BMW X4 2017 Owners Manual

35-watt bulb, H8.1.Insert the screwdriver from the onboardvehicle tool kit, with the flat side on the clip,
arrow 1.2.Turn the screwdriver by 90p, arrow 2.3.Remove the front fog lamp toward the front.4.Detach the connector.5.Turn the bulb bracket and remove it.6.Remove the bulb and replace it.7.Proceed in reverse order to insert the frontfog lamp. Note the guide rails in doing so.LED
front
fog
lights
These front fog lights are made using LED
technology. In the case of a malfunction, conj
tact a dealerss service center or another qualij fied service center or repair shop.
Turn
signal
General
information
Observe the safety information, refer to page 228.
The turn signals are located next to each low beam in the engine compartment.
21-watt bulb, PY 21W.
Replacement1.Open the hood, refer to page 216.2.Turn the bulb with the socket counterj
clockwise and carefully remove.3.Push the bulb down slightly and unscrew from the socket.4.To insert the new bulb, proceed in reverse
order of removal.
Turn
signal
in
exterior
mirror
The turn signals in the exterior mirrors feature LED technology. In the case of a malfunction,contact a dealerss service center or another
qualified service center or repair shop.
Seite 231Replacing
componentsMobility231
Online Edition for Part no. 01 40 2 973 100 - VI/16

Tail
lamps,
bulb
replacement
Overview1Turn signal2Backup lamp3Inside brake lamp4Rear lamp5Brake light
Bulb
replacement,
exterior
tail
lamps General
information
Observe the safety information, refer to page 228.
Turn signal: 21-watt bulb, P21W.
Outer brake lamp: 24-watt bulb, PW24W.
The rear lamp features LED technology. In the case of a malfunction, contact a dealerss servjice center or another qualified service center or
repair shop.
Removing
the
exterior
tail
lamp
1.Open the tailgate.2.Insert the screwdriver from the onboard vehicle tool kit, refer to page 227, frontjward at an angle into the cover opening, arj
row 1.3.Pry the cover out of the lower plug connecjtor, arrow 2.'yLeft vehicle side: pry to the right.'yRight vehicle side: pry to the left.4.To unfasten the upper plug connector, arj
row 3, carefully remove the cover, arrow 4.5.Loosen the two nuts with the screwdriver handle, arrows.6.Remove the tail lamp from the body anddetach the connector from the bulb holder.Seite 232MobilityReplacing
components232
Online Edition for Part no. 01 40 2 973 100 - VI/16

Replacing
the
bulbs1.Loosen the three fasteners, arrows 1, onthe bulb holder and remove the bulb holderfrom the tail lamp, arrow 2.2.Press the nonworking bulb gently into thesocket, turn counterclockwise and remove.
The turn signal is the upper bulb and the brake lamp is the lower bulb on the bulb
holder.3.Proceed in the reverse order to insert the new bulb and attach the bulb holder. Make
sure that the bulb holder engages in all fasj
teners.
Installing
the
tail
lamp
1.Attach the connector to the tail lamp.2.Place the cover on the three fixing points,
arrows, and push in. Make sure that the tail lamp engages in the fasteners.3.Screw the two nuts tight and mount the
cover.Lights
in
the
tailgate
General
information
Observe the safety information, refer to page 228.
Reversing lights: 21-watt bulb, P21W Inner brake lamp: 21-watt bulb, H21W.
Accessing
the
lights1.Open the tailgate.2.Pull out the cover at the recessed grip, arj
row.3.Detach the connector.
Replacing
the
reversing
lamp
and
inner
brake
lamp
1.Detach the bulb holder from the tail lamp.
The reversing lamp is the upper bulb and
the inner brake lamp is the lower bulb on the bulb holder.2.To replace the reversing lamp, pull off the
bulb carefully.
To replace the inner brake lamp, push the
bulb down and turn it to the left.
Installing
the
bulb
holder
1.Attach the connector to the tail lamp.2.Proceed in the reverse order to insert the new bulb and attach the bulb holder.
Ensure that the bulb holder is firmly atj
tached.Seite 233Replacing
componentsMobility233
Online Edition for Part no. 01 40 2 973 100 - VI/16

Rear
lights
and
license
plate
lightsObserve the safety information, refer to
page 228.
These lights are made using LED technology.
In the case of a malfunction, contact a dealerss
service center or another qualified service cenj
ter or repair shop.
Vehicle
battery Maintenance
The battery is maintenance-free.
The added amount of acid is sufficient for the service life of the battery.
More information about the battery can be rej quested from a dealerss service center or anjother qualified service center or repair shop.
Battery
replacement NOTE
Vehicle batteries that are not compatible
can damage vehicle systems and impair vehij
cle functions. There is a risk of personal and
property damage. Only vehicle batteries that are compatible with your vehicle type should
be installed in your vehicle. Information on
compatible vehicle batteries is available at your
dealerss service center.'

Disposing
of
old
batteriesHave old batteries disposed of by adealerss service center or another
qualified service center or repair shop
or take them to a collection point.
Maintain the battery in an upright position for transport and storage. Secure the battery so
that it does not tip over during transport.
Fuses General
information Plastic tweezers and information on the fusetypes and locations are stored in the fuse boxin the cargo area.
Safety
information WARNING
Incorrect and repaired fuses can overload
electrical lines and components. There is a risk of fire. Never attempt to repair a blown fuse.Do not replace a nonworking fuse with a subjstitute of another color or amperage rating.'

Breakdown
assistanceVehicle
features
and
options
This chapter describes all standard, country- specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable country provisions
must be observed.
Hazard
warning
flashers
The button is located in the center console.
The red lamp in the button flashes with the
hazard warning flashers switched on.
Intelligent
emergency
call
Concept
In case of an emergency, an Emergency Rej
quest can be made through the system.
General
information Only press the SOS button in an emergency.
For technical reasons, the Emergency Request cannot be guaranteed under unfavorable conj
ditions.
Overview
SOS button in the roofliner
Requirements
'yThe SIM card integrated in the vehicle hasbeen activated.'yThe radio-ready state is switched on.'yThe Assist system is functional.
Initiating
an
Emergency
Request
1.Press the cover briefly to open it.2.Press the SOS button until the LED at thebutton lights up green.'yThe LED illuminates green when the Emerj
gency Request has been initiated.
If a cancel prompt appears on the Control
Display, the Emergency Request can be
aborted.
If the situation allows, wait in your vehicle
until the voice connection has been estabj
lished.'yThe LED flashes green when a connection to the BMW Response Center has been
established.
When the Emergency Request is received
at the BMW Response Center, the BMW
Response Center contacts you and takes
further steps to help you.Seite 236MobilityBreakdown
assistance236
Online Edition for Part no. 01 40 2 973 100 - VI/16

Even if you are unable to respond, the
BMW Response Center can take further steps to help you under certain circumj
stances.
For this, data is transmitted to the BMW
Response Center which serves to deterj
mine the necessary rescue measures. E.g., the current position of the vehicle, if it canbe established.'yIf the LED is flashing green, but the BMWResponse Center can no longer be heardvia the speaker, you can nevertheless still
be heard at the BMW Response Center.
Initiating
an
Emergency
Request
automatically
Under certain conditions, an Emergency Rej
quest is automatically initiated immediately afj ter a severe accident. Automatic Collision Notij
fication is not affected by pressing the SOS
button.
Roadside
Assistance
Service
availability Roadside Assistance can be reached aroundthe clock in many countries. You can obtain asjsistance there in the event of a vehicle breakj
down.
Roadside
Assistance The Roadside Assistance phone number can
be viewed via iDrive or a connection to Roadj
side Assistance can be established directly.
Warning
triangle
The warning triangle is located behind the left- hand cover in the cargo area.
To remove, loosen the bracket.
First-aid
kit General
information Some of the articles have a limited service life.
Check the expiration dates of the contents regularly and replace any expired items
promptly.
Storage
The first-aid kit is located behind the left-hand
cover in the cargo area.
Jump-starting General
information
If the battery is discharged, the engine can be
started using the battery of another vehicle
Seite 237Breakdown
assistanceMobility237
Online Edition for Part no. 01 40 2 973 100 - VI/16

and two jumper cables. Only use jumper caj
bles with fully insulated clamp handles.
Safety
information DANGER
Contact with live components can lead to
an electric shock. There is a risk of injuries or danger to life. Do not touch any componentsthat are under voltage.'

corresponding engine or body ground of
the vehicle to be started.
Starting
the
engine
Never use spray fluids to start the engine.
1.Start the engine of the assisting vehicle
and let it run for several minutes at an inj creased idle speed.2.Start the engine of the vehicle that is to bestarted in the usual way.
If the first starting attempt is not successj
ful, wait a few minutes before making anj
other attempt in order to allow the disj
charged battery to recharge.3.Let both engines run for several minutes.4.Disconnect the jumper cables in the rej verse order.
Check the battery and recharge, if needed.
Tow-starting
and
towing Safety
information WARNING
Due to system limits, individual functions
can malfunction during tow-starting/towing with the Intelligent Safety systems activated,
e.g., approach control warning with light brakj
ing function. There is a risk of an accident.
Switch all Intelligent Safety systems off prior to
tow-starting/towing.'

Towing
other
vehicles
General
information
Switch on the hazard warning system, dependj
ing on local regulations.
If the electrical system has failed, clearly idenj tify the vehicle being towed by placing a sign
or a warning triangle in the rear window.
Safety
information WARNING
If the approved gross vehicle weight of
the towing vehicle is lighter than the vehicle to be towed, the tow fitting can tear off or it willnot be possible to control the vehicle's rejsponse. There is a risk of an accident! Makesure that the gross vehicle weight of the towjing vehicle is heavier than the vehicle to betowed.'