check engine CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

CLUTCH AND TRANSMISSIONS 7-10 ,

GENERAL DESCRIPTION

The overdrive unit is essentially a two-speed planetary-

transmission attached to the rear of a conventional three-

speed transmission. In overdrive, engine speed is ap-

proximately 30 per cent slower at a given road speed

since the drive train includes planetary gears which pro-

vide a lower overall gear ratio than that obtained in high

gear with the conventional transmission.

The electrical equipment which controls the automatic

action of the mechanical portion of the overdrive unit

consists of a solenoid, a speed-sensitive governor switch,

a relay and a kickdown switch. The circuit including this

equipment makes it possible to operate in overdrive above

a pre-set cut-in speed, or in .conventional drive at any

speed.

With the overdrive unit engaged, the transmission

should not be left in any forward gear with intent of lock-

ing the drive-line as the overrunning clutch is a free-

wheeling condition.
SERVICING THE OVERDRIVE

With the,overdrive assembly removed from the trans-

mission, service operations on the transmission proper

are the same as for the standard three-speed trans-

mission.

Repairs to the overdrive housing, output shaft, ring

gear assembly, clutch cam, roller retainer, pinion cage,

sun gear, shift rail, sun gear control plate, output shaft

bearing, oil seal, speedometer drive gear, solenoid pawl

and interlock plunger may be performed underneath the

car, if so desired, by removing the overdrive housing

without disturbing the transmission. Refer to Overhaul

Manual for Service Procedure.

If the transmission mainshaft, overdrive adapter or

transmission rear bearing which is retained in adapter

require replacement, the entire transmission and over-

drive assembly should be removed and overhauled on the

bench.

MAINTENANCE AND ADJUSTMENTS

Servicing of the overdrive governor switch and pinion,

the sun gear solenoid, oil seal and cable bracket, the out-

put shaft rear oil seal, the control shaft lever, and the

speedometer driven gear may be accomplished without

removing the overdrive from the vehicle, as discussed

in the following paragraphs:

GOVERNOR SWITCH AND PINION

To remove governor switch, disconnect wires at gover-

nor switch and screw governor
out
of housing, using Tool

J-4653 on the flat hexagonal surface of governor case.

The pinion may be separated from the governor by re-

moving the snap ring on the shaft.

SUN GEAR SOLENOID, OIL SEAL AND

CONTROL CABLE BRACKET

Remove the solenoid by taking out the two mounting

bolts and lock washers, removing
the.
cable bracket with

the lower bolt. Turn the solenoid 1/4 turn and
pull,
sole-

noid plunger out of adapter. The oil seal may be pried

out of the adapter.

CASE REAR OIL SEAL

Removal

1.
Remove propeller shaft as outlined in Section 4.

2.
Using a punch against seal in housing, pry out seal

from housing.

Installation

1.
Prelubricate between sealing lips and coat outside of

new oil seal with a suitable sealant, then start seal

into bore in overdrive housing.

2.
Using Tool J-5154 drive oil seal into counterbore.

3.
Install propeller shaft as outlined in Section 4.

CONTROL SHAFT LEVER AND/OR "O" RING

OIL SEALS

To remove- the control shaft, disconnect the cpntrol
cable, remove tapered pin and pull lever out. Replace

the two "0" ring seals on the control shaft. Insert shaft

and new "O" ring seals into housing and install tapered

pin. Connect control wire to lever.

SPEEDOMETER DRIVEN GEAR

Disconnect speedometer cable, remove lock plate to

housing bolt and lock washer and remove lock plate. In-

sert screw driver in lock plate slot in fitting and pry

fitting, gear and shaft from housing. Pry "O" ring from

groove in guide.

Install new "O" ring in groove in fitting and insert

shaft.

Hold the assembly so slot in fitting is toward lock plate

boss on housing and install in housing. Push fitting into

housing until lock plate can be inserted in groove and

attached to housing.

L
dl

ZAIR GAP

km (CHECK WITH

M*= POINTS BARELY
'A

AoWER
|^

POINT

0 ADJUST

=^ i
SUPPORT

Fig. IB - Checking Relay Air Gap

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-13

PULL-IN

WINDING
li
HOLD-IN

WINDING

Fig.
4B -
Overdrive Electrical Circuit Wiring Diagram

ELECTRICAL

Any one of the following general complaints may be due

to electrical trouble in the overdrive circuit.

1.
Does not engage.

2.
Does not release.

3.
Does not kickdown from overdrive.

These troubles may be traced and remedied as de-

scribed in the following paragraphs.

1.
Does not engage

a. With the ignition switch on, ground the "KD" ter-

minal of the solenoid relay with a jumper lead.

If the solenoid clicks, the relay and solenoid cir-

cuits are in operating condition. If no click is

heard in the relay, check the fuse and replace if

defective.

b.
If the fuse is good, use a second jumper lead to

connect the "SOL" and "BAT" terminals of the

relay. If a click is now heard in the solenoid, the

relay is probably at fault and should be repaired

or replaced.

c. If the solenoid does not click in Step b, check the

wiring to the No. 4 terminal of the solenoid and

replace if necessary. If the wiring is not defec-

tive,
the trouble is probably in the solenoid. Re-

move the solenoid cover, examine the solenoid

contacts in series with the pull-in winding and

clean if necessary. Test again for clicks, as in

Step b, after replacing solenoid cover and lead

wires.
Replace the solenoid if trouble has not

been corrected.

d. If the relay and solenoid circuits are in good con-

dition as determined in Step a, leave the ignition

switch on and make sure the manual control knob

is in the overdrive position. Ground one and then

the other of the two terminals next to the stem of

the kickdown switch (identified as "SW" and
?fREL"). K the solenoid clicks when one terminal

is grounded but not the other, replace the switch.

If the solenoid does not click when either of the

terminals is grounded, check the wiring between

the relay and the kickdown switch and replace if

defective.

e. If the solenoid clicks as each terminal is grounded

in Step d, ground the governor switch terminal.

If the solenoid clicks, the governor switch may be

defective. If the solenoid does not click, check

the wiring between the kickdown and governor

switches and replace if necessary.

2.
Does not release

a. Remove the connection to the "KD" terminal of

the relay. If this release overdrive, look for a

grounded control circuit between the relay and

governor switch.

b.
If the overdrive is not released in Step a, dis-

connect the lead to the "SOL" terminal of relay.

If this releases the overdrive, replace the relay.

3.
Does not kickdown from overdrive

a. With the engine running, connect a jumper lead

between the No. 6 terminal of the solenoid and

ground. Operate the kickdown switch by hand.

This should stop the engine. If it does, the sole-

noid is probably defective and it should be checked

for dirty ground-out contacts or other defects

within the ground-out circuit of the solenoid (fig.

4B).
Clean the contacts or replace the contact

plate as required.

b.
If the engine does not stop in Step a, ground one

and then the other of the two terminals (Identified

as "IGN" and "SOL") farthest from the sfem of

the kickdown switch. The engine should stop when

one of the two terminals (IGN) is grounded. If

the engine does not stop when the terminal is

grounded, the wiring or connections to the switch

between the switch and coil are defective. When

the btlier terminal (SOL) is grounded, the engine

should stop when the kickdown switch is operated.

If the engine does not stop when the kickdown

switch is operated with the second terminal

grounded, the kickdown switch is defective. If

the trouble is in the kickdown switch, adjust the

linkage to give more travel of the switch rod.

If this does not correct the trouble, replace the

kickdown switch.

If the kickdown switch operates as it should,

check for an open circuit in the wiring between

the kickdown switch and the No. 6 terminal of the

solenoid.

c. If the trouble is not located by the above checks,

the upper contacts of the kickdown switch may not

be opening. To check for this condition, ground

the overdrive control circuit at the governor

switch. This should cause the solenoid to click.

Operate the kickdown switch by hand. This should

cause a second click as the solenoid releases.

If there is no second click, adjust the linkage to

give more travel of the switch rod. If this does

not correct the trouble, replace the kickdown

switch.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-14

SPEED HEAVY DUTY TRANSMISSION

(WARNER MODEL T 16)

INDEX

General Description ......

Maintenance and Adjustments

Shift Linkage Adjustment

Side Cover ........

Removal .........

Disassembly
7-14

7-14

7-14

7-14

7-14

7-14
Assembly 7-14

Installation • 7-15

Other Maintenance
&
Adjustment

Operations See 3-Speed Saginaw Section

Transmission Replacement . . . See 3-Speed Saginaw Section

GENERAL DESCRIPTION

The Borg-Warner heavy duty three speed fully syn-

chronized (all forward gears) transmission incorporates

helical gears throughout specially designed to provide

high torque capacity, and gear teeth proportion to operate

at high speeds with neither excessive heat generation nor

excessive frictional losses. Shafts, bearings, high ca-

pacity clutches and other precision parts are held to

close limits providing proper clearances necessary for

durability during extended heavy usage.

The main drive gear is supported by a heavy duty ball

bearing at the front end of the transmission case and is

piloted at its front end in an oil impregnated bushing

mounted in the engine crankshaft. The front end of the

mainshaft is piloted in a row of roller bearings set into

the hollow end of the main drive gear and the rear end

is carried by a heavy duty ball bearing mounted in the

front of the extension housing.

The countergear is carried on a double row of rollers

at both ends while thrust is taken on thrust washers lo-

cated between the ends of the gear and the thrust bosses

in the case. An anti-rattle plate assembly at the front
of the countergear provides a constant spring tension be-

tween the counter and clutch gears to reduce torsional

vibrations. The reverse idler gear is carried on 25

roller bearings while thrust is taken on thrust washers

located between the ends of the gear and the thrust bosses

of the case.

Gear shifting is manual through shift control rods from

the shifter tube in the mast jacket to the rearward shift

lever of the side cover assembly for first and reverse

gear; and through a cross shaft assembly attached to the

forward side cover lever for second and third gear. All

three forward gears are fully synchronized. The syn-

chronizer assemblies consist of a clutch hub, clutch

sleeve, two clutch key springs and three energizer clutch

keys and are retained as an assembly on the main shaft

by a snap ring. The transmission may be used as an aid

in deceleration by downshifting in sequence without

double-clutching or any gear clashing. Reverse is not

synchronized, however, it is a helical gear to insure

quiet operation.

MAINTENANCE AND ADJUSTMENTS

Refer to similar procedures under the 3-speed Saginaw

Transmission Section for—Column Mounted Shift Linkage

Adjustment, Speedometer Driven Gear and Oil Seal Re-

placement, Extension Oil Seal Replacement and Trans-

mission Replacement. ~~

Camaro and Corvette Floor Shift Linkage Adjustment

(Fig.
lc)

1.
Set Lever (L), (K) in neutral position.

2.
Move Lever Assembly (A) and Levers (C), (D) to

neutral position and insert Locating Gauge (B) into

control Lever Bracket Assembly.

3.,
Install Rod (H) with Retainer (M) on Lever (L).

4.
With two Jam Nuts (G), (E) and Swivel (F) loose on

Rod (H) insert and attach Swivel with Retainer (N)

to Lever (D).

5.
Repeat steps 3 and 4 for Rod (J) and Levers (C
&
K).

6. Remove' Locating Gauge and check shift to insure

proper operation.

SIDE COVER ASSEMBLY

Removal

1.
Drain transmission and disconnect control rod and

cross shaft from side cover levers. *

2.
Remove nine cap screws securing the transmission

side cover assembly to transmission, case and re-

move cover assembly, shifting forks, and gasket.
Disassembly (Fig. 2C) '

1.
Remove shifting forks from shift lever assemblies.

2.
Remove nut and lock washer from each shift lever

shaft.

3.
Remove outer shift levers and lightly tap shift lever

shafts from assembly.

4.
Remove two steel balls, poppet spring, interlock pin

and interlock sleeve from cover.

5.
Remove "O" ring seals from shift lever shafts.

Assembly (Fig. 2C)

1.
Install new "O" ring seals to shift lever shafts.

2.
Install low and reverse shifter shaft and plate as-

sembly to cover.

3.
Place shifter shaft and plate assembly in neutral po-

sition, middle detent, and install interlock sleeve,

ball, poppet spring and interlock pin.

4.
Install remaining poppet ball and then install second

and third shifter shaft and plate assembly.

NOTE: Installation is easiest if shifter shaft

and plate assembly passes over ball in its neu-

tral position.

5.
Check clearance between end of interlock sleeve and

shifter shaft and plate cams when one plate is in

neutral and the other is shifted into gear position.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-16

FOUR-SPEED TRANSMISSION (MUNCIE)

INDEX

Page

General Description 7-16

Maintenance and Adjustments 7-16

Shift Linkage Adjustment 7-16

Gearshift Lever Reverse Blocker Cable 7-17

Replacement . 7-17

Adjustment 7-17

Speedometer Driven Gear and Oil Seal 7-19

Replacement 7-19

Transmission Side Cover 7-19

Removal 7-19
Page

Disassembly 7-19

Assembly 7-19

Installation . 7-19

Extension Oil Seal ......... 7-19

Replacement 7-19

Component Parts Replacement 7-20

Transmission Replacement 7-20

Removal from Vehicle , 7-20

. Installation in Vehicle . . . 7-20

GENERAL DESCRIPTION

The four-speed synchromesh transmission incorpo-

rates helical gears throughout specially designed to pro-

vide high torque capacity without additional weight, and

gear teeth proportioned to operate at high speeds with

neither excessive heat generation nor excessive fric-

tional losses. Shafts, bearings, high capacity clutches

and other precision parts are held to close limits, pro-

viding proper clearances necessary for durability during

extended heavy usage.

The main drive gear is supported by a heavy-duty ball

bearing at the front end of the transmission case and is

piloted at its front end in an oil impregnated bushing

mounted in the engine crankshaft. The front end of the

mainshaft is piloted in a row of roller bearings set into

the hollow end of the main drive gear and the rear end

is carried by a heavy-duty ball bearing mounted at the

rear end of the transmission case in a retainer casing.

The counter gear is carried on a double row of rollers

at both ends while thrust is taken on thrust washers lo-
cated between the ends of the gear and the thrust bosses

in the case.

The two-piece reverse idler gear is carried on bronze

bushings while thrust is taken on thrust washers located

between the front of the gear and the back of the reverse

idler thrust boss and between the rear of the gear and the

reverse idler shaft boss in the case extension.

Gearshifting is manual through shift control rods to the

transmission cover shifter levers for first through fourth

gears,
and to the reverse lever located in the case ex-

tension. The shifter lever to the rear of the transmis-

sion cover controls first and second gears while the

lever to the front controls third and fourth gears. All

four forward gears are fully synchronized. The trans-

mission may be used as an aid in deceleration by down-

shifting in sequence without double clutching. Reverse is

not synchronized, however, it is a helical gear to insure

quiet operation.

MAINTENANCE AND ADJUSTMENTS

SHIFT LINKAGE ADJUSTMENT (EXC. CORVETTE

AND CAMARO) (Fig. 1m)

1.
Set Transmission Levers (M), (P) and (S) in neutral

detent position.

2.
Move Shift Lever (A) to neutral detent position and

insert a Locating Gauge (1/8" thick by 41/64" (.646)

wide and 3" long) (B) into Control Lever Bracket

Assembly slot.

3.
Install Rod (V) with retainer on Lever (D).

4.
Maintaining Lever (D) against Locating Gauge, ad-

just Clevis (T) at Lever (S) until clevis pin freely

passes through holes in Clevis and Lever.

5. Install clevis pin, washer, and cotter pin. Tighten

Jam Nut (U) against Clevis.

6. Install Rod (H) with retainer on Lever (W).

7. With Jam Nuts (J) and (L) and Swivel (K) loose on

Rod (H), insert and attach Swivel with washer and

retainer to Lever (M).

8. Maintaining Lever (W) against Locating Gauge (B)

and while holding Swivel (K), run Jam Nut (J) against

Swivel until Nut contacts Swivel. Then tighten Jam

Nut (L) against Swivel.

9. Install Rod (R) with retainer on Lever (P).

10.
With Jam Nuts (E) and (G) and Swivel (F) loose on

Rod (R), insert and attach Swivel with retainer to
Lever (C).

11.
Maintaining Lever (C) against Locating Gauge (B) and

while holding Swivel (F), run Jam Nut (G) against

Swivel until Nut contacts Swivel. Then tighten Jam

Nut (E) against Swivel.

12.
Remove Locating Gauge and check shifts to insure

proper operation. Readjust clevis and swivels if

necessary.

NOTE:
Control rods may be attached to trans-

mission shift lever lower holes, to reduce shift

lever travel, for a "faster shift" adjustment op-

tion.
Increased shifting effort is required when

control rods are installed in this "short throw"

position.

CORVETTE AND CAMARO SHIFT LINKAGE

ADJUSTMENT (Fig. 2M)

1.
Set Transmission Shift Levers in neutral position.

2.
Move Shift Lever (A) to neutral position and insert

Locating Gauge (C) into control Lever Bracket As-

sembly (B).

3.
Install Reverse Rod (J) with Retainer on Lever (O).

4.
With two Jam Nuts and Swivel loose on Rod (J) insert

and attach Swivel with Retainer to Lever (D).

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH
AND
TRANSMISSIONS
7-20

COMPONENT PARTS REPLACEMENT

3.

4.

5.

6.
TRANSMISSION REPLACEMENT
(EXC.
CORVETTE)

Removal From Vehicle

1.
Remove shift lever trim plate and dust boot.

Remove shift lever assembly.

Raise vehicle
to
desired working height.

Disconnect
the
speedometer cable from speedometer

driven gear fitting.
.
~
. •

Remove propeller shaft, then support engine
at the

oil
pan
rail with
a
jack
or
other suitable support

capable
of
supporting
the
engine when transmission

is removed.

Disconnect shift lever bracket assembly from exten-

sion
and
remove
all 3
transmission shifter levers

from shifter shafts, (leave linkage connected
to

levers)
and
remove bracket assembly levers
and

linkage.

Remove extension mount7 to-crossmember attaching

bolts.

Loosen transmission crossmember
and
move rear-

ward
or
remove.

Remove
the
transmission-to-clutch housing retaining

bolts
and
install two guide pins, J-1126,
in
top holes.

Slide
the
transmission straight back until
the
input

shaft
is
free
of
splines
in the
clutch disc.

Slide
the
transmission rearward
to
allow sufficient

clearance
of
input shaft
and
clutch housing. Then tilt

input shaft
end of
transmission downward and with-
8.

9.

10.

11.
draw transmission from vehicle.

installation
to
Vehicle

1.
Raise transmission
and
rotate
as
necessary-to start

input shaft into clutch disc
and
slide transmission

forward until
it
bottoms against clutch housing.
Re-

move guide pins.

2.
Install
the
transmission-to-clutch housing retaining

bolts.
Torque
all
four retaining bolts
to 50 ft. lbs.

3.
Raise engine
and
position extension mount
to
cross-

member,
and
loosely install
the
retaining bolts.

Tighten crossmember
to
frame retaining bolts.

4.
Remove temporary support from engine, and torque

the extension mount retaining bolts.

5. Install propeller shaft.

6. Install control lever bracket assembly
to
transmis-

sion extension
and
connect shifter levers
to
shifter

shafts.

7. Fill transmission
to
level
of
filler plug hole with

correct lubricant specified
in
Section
0.

8. Lower vehicle and install shift lever assembly, check

shift pattern and adjust linkage
as
required.

9. Install trim plate and dust boot.

CORVETTE TRANSMISSION REPLACEMENT

Refer
to
similar procedure under 3-Speed Corvette

Transmission.

FOUR-SPEED (SAGINAW) TRANSMISSION

INDEX

Page

General Description
7-20

Maintenance
and
Adjustments
. . 7-21

Shift Linkage Adjustment.
. 7-21

Speedometer Driven Gear
and

Oil Seal ................
(See
Muncie 4-Speed)

Side Cover
7-22
Page

Removal
. . , 7-22

Disassembly
. . 7-22

Assembly
. . . 7-22

Installation
. 7-22

Extension
Oil
Seal
(See
Muncie 4-Speed)

Transmission Replacement (See Muncie 4-Speed)

GENERAL DESCRIPTION

The Saginaw four speed fully synchronized
(all
forward

gears) transmission incorporates helical drive gears

throughout.

The main drive gear
is
supported
by a
ball bearing
at

the front
end of the
transmission case and
is
piloted
at its

front
end in an oil
impregnated bushing mounted
in the

engine crankshaft.
The
front
end of the
mainshaft
is

piloted
in a row of
roller bearings
set
into
the
hollow
end

of
the
main drive gear
and the
rear end
is
carried
by a

ball bearing mounted
in the
front
of the
extension housing.

The countergear
is
carried
on a
single
row of
rollers

at both ends while thrust
is
taken on thrust washers
lo-

cated between
the
ends
of the
gear and
the
thrust bosses

in
the
case. Ah anti-rattle plate assembly
at the
front
of

the countergear provides
a
constant spring tension
be-

tween
the
counter
and
clutch gears
to
reduce torsional

vibrations.
The
sliding reverse idler gear
is
carried
on

a bushing finish bored
in
place.
It
rotates
on a
short

idler shaft retained by
a
woodruff
key.

The synchronizer assemblies consist
of a
clutch
hub,

clutch sleeve,
two
clutch
key
springs and three energizer

clutch keys
and are
retained
as an
assembly on
the
main

shaft
by a
snap ring.
A great deal
of
similarity
and
interchangeability
now

exists between
the new 3 and
4-speed Saginaw trans-

missions.

However,
the
synchronizer assembly
at the
front
of the

mainshaft
is
used
for the
third and fourth rather than
the

second
and
third shift.
The
synchronizer assembly
at

the rear
of the
mainshaft
is
used
for the
first and second

rather than
the
first
and
reverse shift. Gear teeth
cut

in
the
first and second synchronizer sleeve (reverse gear)

distinguish
it
from
the
third
and
fourth synchronizer

sleeve.

Starting from
the
front, gears
on the
mainshaft
are

third, second
and
first rather than second, first and
re-

verse.
A
fourth blocker ring
is
used between
the 1-2

synchronizer assembly
and
first gear
on the
four-speed

transmissions.

The cover
on the new
four-speed transmission
is lo-*

cated
on the
left-hand side
of the
case.
It is
similar
to

the three-speed cover with
the
addition
of a
reverse

shifter shaft assembly, detent ball
and
detent spring.

Disassembly
and
assembly procedures
are
covered
in

this section.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH
AND
TRANSMISSIONS
7-23

Assembly (Fig.
4X)

1.
With detent spring tang projecting
up
over
the 3rd

and
4th
shifter shaft cover opening install
the
first

and second detent
cam
onto
the
detent
cam
pivot
pin.

With
the
detent spring tang projecting
up
over
the

first
and
second shifter shaft cover hole install
the

3rd
and 4th
detent
cam,

NOTE:
The 1-2
detent
cam has a
.090" greater

contour
on the
inside detent notch.

2.

3.
Install detent
cam
retaining
"C"
ring
to
pivot shaft,

and hook spring into detent
cam
notches.

Install
1-2 and 3-4
shifter shaft assemblies
in
cover

being careful
not to
damage seals. Install both shift

forks
to
shifter shaft assemblies, lifting
up on
detent
cam
to
allow forks
to
fully seat into position.

4.
Install reverse detent ball
and
spring
to
cover, then

install reverse shifter shaft assembly
to
cover.

5.
Install outer shifter levers, flat washers, lock wash-

ers
and
bolts.

Installation

1.
Shift shifter levers into neutral detent (center) posi-

tion. Position cover gasket
on
case.

2.
Carefully position side cover into place making sure

the shift forks
are
aligned with their respective

mainshaft clutch sliding sleeves.

Install cover attaching bolts
and
tighten evenly
to

specified torque.

Remove filler plug
and add
lubricant specified
in

Section
0, to
level
of
filler plug hole.
3.

4.

ALUMINUM POWERGLIDE

INDEX

Page

General
Description
7-23

Maintenance
and
Adjustments .............. 7—23

Oil
Level Check
7-23

Periodic
Oil
Change
7-24

Periodic
Low
Band Adjustment
7-24

Manual
Shift Linkage Check
and
Adjust
7-24

Floor
Shift Linkage
7-25

Floor
Mounted Control Lever
and

Bracket
Assembly
7-29

Throttle
Valve Linkage
.... 7-29

Neutral
Safety Switch
.. . 7-30

Throttle
Return Check Valve (Dashpot)
7-30

Component
Parts Replacement
7-30

Transmission
Replacement .............. 7—30
Page

Other
Service Operations
7-32

Diagnosis
7-32

Warming
Up
Transmission
7-32

Shop
Warm
Up , 7-32

Road
Warm
Up 7-32

Checking
Fluid Level
and
Condition
7-32

Manual
Linkage
7-32

Oil
Leaks
7-33

Basic
Pressure Checks
7-33

Wide
Open Throttle Upshift Pressure Check
.... 7-33

Idle
Pressure
in
Drive Range
7-33

Manual
"Low"
Range Pressure Check .......
7-33

Drive
Range Overrun (Coast) Pressure
.
.......
7-33

Powerglide
Shift Points
. . 7-35

GENERAL DESCRIPTION

The case
and
converter housing
of the two
speed alumi-

num Powerglide Transmission
is a
single case aluminum

unit. When
the
manual control
is
placed
in the
drive
po-

sition,
the
transmission automatically shifts
to low
gear

for initial vehicle movement.
As the car
gains speed
and

depending
on
load
and
throttle position,
an
automatic shift

is made
to
high gear.
A
forced downshift feature
pro-

vides
a
passing gear
by
returning
the
transmission
to low

range.

The
oil
pump assembly
is a
conventional gear type
and

the
oil
pump housing
is of the
large diameter type acting

as
the
front bulkhead
of the
transmission.
The
torque

converter
is a
conventional three element welded design

bolted
to the
engine flywheel which drives through
a
two-

speed planetary gearset.
The
high clutch assembly
is

typical
of the
designs used
in
this type transmission.
The

aluminum Powerglide uses
an
output shaft mounted
gov-
ernor which requires
a
hole through
the
output shaft.
The

reverse clutch assembly
is a
multiple disc type clutch.

The steel plates
are
splined directly
to the
case while
the

face plates
are
splined
to the
internal
or
ring gear.
The

clutch piston operates within
the
rear portion
of the
case.

The internal diameter
of the
pistoh
is
sealed to
an
integral

hub portion
of the
case rear bulkhead.
The
outside
dia-

meter
is
sealed
to a
machined portion
of the
case.
The

piston
is
hydraulically applied
and is
released
by
separate

coil springs.
The
valve body assembly
is
bolted
to the

bottom
of the
transmission case
and is
accessible
for

service
by
removing
the oil pan
assembly.
The
valve

body consists
of an
upper
and
lower body located
on
either

side
of a
transfer plate.
The
vacuum modulator
is lo-

cated
on the
left rear face
of the
transmission case.
The

modulator valve bore
is
located
in the
upper valve body.

MAINTENANCE
AND
ADJUSTMENTS

OIL LEVEL CHECK

The transmission
oil
level should
be
checked period-

ically
as
recommended
in
Section
0. Oil
should
be
added

only when level
is on or
below
the
"ADD" mark
on the dip

stick with
oil hot or at
operating temperature.
The oil

level
dip
stick
is
located
at the
right rear
of the
engine
compartment. Fill with
oil
specified
in
Section
0.

In order
to
check
oil
level accurately,
the
engine should

be idled with
the
transmission
oil hot and the
control

lever
in
neutral (N) position.

It
is
important that
the oil
level
be
maintained
no

higher than
the
"FULL" mark
on the
transmission
oil

level gauge.
DO NOT
OVERFILL,
for
when
the oil
level

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-24

is at the full mark on the dip stick, it is just slightly be-

low the planetary gear unit. If additional oil is added,

bringing the oil level above the full mark, the planetary

unit will run in the oil, foaming and aerating the oil. This

aerated oil carried through the various oil pressure pas-

sages (low servo, reverse servo, clutch apply, converter,

etc.) may cause malfunction of the transmission assem-

bly, resulting in cavitation noise in the converter and

improper band or clutch application. Overheating may

also occur.

If the transmission is found consistently low on oil, a

thorough inspection should be made to find and correct

all external oil leaks.

PERIODIC OIL CHANGE

The transmission oil should be changed periodically as

recommended in Section 0, and whenever transmission is

to be removed from the vehicle for repairs.

1.
Run engine for one minute in neutral prior to chang-

ing.

2.
Be sure vehicle is level or raise from the rear only.

3.
Remove the oil pan drain plug and allow oil to drain

thoroughly into a pan or can.

Replace drain plug and refill with approximately two

quarts of oil specified in Section 0.

NOTE: To refill the transmission, remove dip

stick from oil filler tube and refill transmission

with oil specified in Section 0 using filler tube

and funnel J-4264. Then, after shifting into all

ranges at idle speed to fill all oil passages, the

engine should be run at 800-1000 rpm with the

transmission in Neutral until the oil warms up,

then add oil as required to raise the fluid level

to the full mark on the dip stick. Refill capacity

is approximately 2 qts.
4.

Fig.
1PG - Adjusting Low Band Using J-21848
PERIODIC LOW BAND ADJUSTMENT (Fig. 1PG)

Low band adjustment should be periodically performed

at 12,000 mile intervals, or sooner, as necessary if op-

erating performance indicates low band slippage.

1.
Raise vehicle and place selector lever in neutral.

2.
Remove protective cap from transmission adjusting

screw.

3.
a. On Corvette Models: Drop left exhaust pipe for

clearance.

b.
On Chevelle Models: To gain clearance between

underbody and transmission, it may be necessary

to remove rear mount bolts from crossmember,

and move transmission slightly toward passenger

side of vehicle. .

4.
Loosen adjusting screw lock nut 1/4 turn and hold in

this position with wrench.

5.
Using Special Tool J-21848 adjust band to 70 in. lbs.

and back off four (4) complete turns for a band which

has been in operation for 6,000 miles or more,.or

three (3) turns for one in use less than 6,000 miles.

CAUTION: Be sure to hold the adjusting screw

lock nut at 1/4 turn loose with a wrench during"

the.adjusting procedure.

6. Tighten the adjusting screw lock nut to specified

torque.

CAUTION: The amount of back-off is not an

approximate figure, it must be exact.

MANUAL SHIFT LINKAGE CHECK & ADJUST

(Column Type)

1.
The shift tube and lever assembly must be free in the

mast jacket. See Section 9 for alignment of steering

column assembly if necessary.

2.
To check for proper shift linkage adjustment, lift

the transmission selector lever towards the steering

wheel. Allow the selector lever to be positioned in

drive (D) by the transmission detent.

NOTE: Do not use the indicator pointer as a

reference to position the selected lever. When

performing linkage adjustment, pointer is ad-

justed last.

3.
Release the selector lever. The lever should be in-

hibited from engaging low range unless the lever is

lifted.

4.
Lift the selector lever towards the steering wheel,

and allow the lever to be positioned in neutral (N) by

the transmission detent.

5.
Release the selector lever. The lever should now

be inhibited from engaging reverse range unless the

lever is lifted.

6. A properly adjusted linkage will prevent the selector

lever from moving beyond both the neutral detent, and

the drive detent unless the lever is lifted to pass

over the mechanical stop in the steering column.

7.
In the event that an adjustment is required, place

the selector lever in drive (D) position as determined

by the transmission detent. See Steps 2 and 3.

8. Loosen the adjustment swivel at the cross-shaft,

and rotate the transmission lever so that it contacts

the drive stop in the steering column.

9. Tighten the swivel and recheck the adjustment. See

2 and 6.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS
7*30

V-8 Models-With Uni-Directional Linkage

1.
Remove air cleaner.

2.
Disconnect accelerator linkage at carburetor.

3.
Disconnect accelerator return and TV rod return

springs.

4.
With right hand, pull TV upper rod forward until

transmission is through detent. With left hand, open

carburetor to wide open throttle position. Carbure-

tor must reach wide open throttle position at the

same time the ball stud contacts end of slot in upper

TV rod.

5. Adjust swivel on end of upper TV rod to obtain set-

ting described in Step 4. Allowable tolerance is

approximately 1/32".

6. Connect and adjust accelerator linkage as described

in Section 6.

7. Check for throttle linkage freedom.

Neutral Safety Switch Adjustment

The adjustment at the neutral safety switch is de-

scribed in the Electrical Section 12.

Throttle Return Check Valve (Dashpot) Adjustment

The adjustment of the throttle return check valve is

described in Section 6M for each carburetor installation.
Fig.
12PG - Floor Mounted Control Lever and

Bracket Assembly (Chevrolet Shown)

COMPONENT PARTS REPLACEMENT

TRANSMISSION REPLACEMENT (EXC. CORVETTE)

Removal

1.
Raise car on hoist (preferably) or on stand jack and

remove oil pan drain plug to drain oil.

NOTE:
If desired, the oil may be drained after

transmission removal.

2.
Disconnect the oil cooler lines (external cooled

models), vacuum modulator line and the speedometer

drive cable fitting at the transmission. Tie lines

out of the way.

3.
Disconnect manual and TV control lever rods from

transmission.

4.
Disconnect propeller shaft from transmission.

5. Install suitable transmission lift equipment to jack

or other lifting device and attach on transmission.

6. Disconnect engine rear mount on transmission ex-

tension, then disconnect the transmission support

crossmember and slide rearward.

7. Remove converter underpan, scribe flywheel-con-

verter relationship for assembly, then remove the

flywheel-to-converter attaching bolts.

NOTE:
The "light" side of the converter is

denoted by a "blue" stripe painted across the

ends of the converter cover and housing. This

marking should be aligned as closely as possible

with the "white" stripe painted on the. engine

side of the flywheel outer rim (heavy side of

engine) to maintain balance.

8. Support engine at the oil pan rail with a jack or other

suitable brace capable of supporting the engine

weight when the transmission is removed.
9. Lower the rear of the transmission slightly so that

the upper transmission housing-to-engine attaching

bolts can be reached using a universal socket and a

long extension. Remove upper bolts.

CAUTION: Oh V-8 engines, care must be taken

not to lower rear of transmission too far as the

distributor housing may be forced against the

dash causing damage to the distributor. It is

best to have an assistant observe clearance of

all upper engine components while the trans-

mission rear end is being lowered.

10.
Remove remainder of transmission housing-to-

engine attaching bolts.

11.
Remove the transmission by moving it slightly to the

rear and downward, then remove from beneath the

car and transfer to a work bench.

NOTE:
Observe converter when moving the

transmission rearward. If it does not move

with the transmission, pry it free of flywheel

before proceeding.

CAUTION: Keep front of transmission upward

to prevent the converter from falling out. Install

converter Tool J-9549 (or a similar tool con-

structed as shown in Figure 13PG, or, in an

emergency, a length of strong wire may be used)

immediately after removal from the engine.

Installation

NOTE:
The "light" side, of the converter is

denoted by a "blue" stripe painted across the

ends of the converter cover and housing. This

marking should be aligned as closely as possible

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-31

with the "white" stripe painted on the engine

side of the flywheel outer rim, denoting the

"heavy" side of the engine.

1.
Mount transmission on transmission lifting equip-

ment installed on jack or other lifting device.

2.
Remove converter holding tool.

CAUTION: Do not permit converter to move

forward after removal of holding tool.

3.
Raise transmission into place at rear of engine and

install transmission case to engine upper mounting

bolts,
then install remainder of the mounting*bolts.

Torque bolts to 35 ft. lbs.

4.
Remove support from beneath engine, then raise

rear of transmission to final position.

5. Through flywheel cover opening align as closely as

possible the "white" flywheel balance mark stripe

and the "blue" painted stripe on the end of converter

cover and housing. If scribed during removal, align

scribe marks on flywheel and converter cover. In-

stall converter to flywheel attaching bolts. Torque

bolts to 15-20 ft. lbs.

6. Install converter under pan.

7. Reinstall transmission support crossmember to

transmission and frame.

8. Remove transmission lift equipment.

9. Connect propeller shaft to transmissions.

10.
Connect manual and TV control lever rods to

transmission.

11.
Connect oil cooler lines (if so equipped), vacuum

Fig.
13PG - Converter Holding Tool
modulato:* line, and speedometer drive cable to

transmission.

12.
Refill transmission through filler tube, using Funnel

J-4264 and following the recommended procedure

provided earlier in this section.

13.
Check transmission for proper operation and for

leakage. Check and, if necessary, adjust linkage.

CORVETTE POWERGLIDE TRANSMISSION

Replacement

1.
Disconnect battery ground cable.

2.
Remove ball end from transmission shift control

lever.

3.
Raise front and rear of vehicle.

4.
Insert a block of wood between the top of the dif-

ferential carrier housing and the underbody (to

prevent upward travel of the carrier when the car-

rier front support is disconnected).

5. Disconnect the differential carrier front support

from its frame bracket, by removing the nut on the

underside of the biscuit mount.

6. Pry the carrier downward to relieve load while re-

moving the two center mounting bolts from the

carrier front support. (To pry carrier downward

insert crowfoot end of a pry bar**hrough the open-

ing in the carrier front support, hooking end of bar

over top of the center mounting bolt pad cast in the

underside of the carrier).

7. Pivot carrier support downward for access to prop

shaft "U"-joint.

8. Disconnect prop shaft front and then rear
"U"
bolts.

9. Disconnect parking brake cable from ball socket at

idler lever located near center of underbody.

10.
Remove prop shaft by moving shaft forward.

11.
Remove left bank exhaust pipe.

12.
Remove right bank exhaust pipe and heat riser.

13.
Disassemble the transmission mount, as follows:

a. Remove the two bolts that attach rear mount

cushion to the rear mount bracket.

b.
Support engine under oil pan and raise engine to

remove load from rear mount cushion.

CAUTION: To avoid damage to oil pan, a suit-

able wide base, heavy wood platform should be

placed between the jack pad and the oil pan.

c. Remove the three transmission mount bracket-

to-crossmember bolts, then remove mount

bracket.

d. Remove the two bolts from mount pad to trans-

mission case and remove rubber mount cushion

and exhaust pipe "yoke".

14.
Disconnect oil cooler lines at transmission and

swing lines clear.

15.
Remove connector underpan.

16.
Remove converter to flywheel attaching bolts.

17.
At transmission disconnect vacuum modulator line

and speedometer cable.

18.
Disconnect transmission shift linkage from trans-

mission gearshift control lever. Remove shift lever.

19.
At transmission, remove throttle valve linkage and

disconnect neutral safety switch linkage, also re-

move the gearshift control linkage.

20.
Remove neutral safety switch from transmission

control bracket.

CHEVROLET CHASSIS SERVICE

CLUTCH AND TRANSMISSIONS 7-32

21.
Remove transmission output shaft slip yoke and in-

sert a plastic shipping plug in end of extension to

prevent spillage of transmission fluid.

NOTE:
The yoke is removed to avoid tearing

the heat reflecting pad on the underbbdy, when

the transmission is being removed.

22.
Remove bright metal ignition shielding from dis-

tributor area.

23.
Remove the transmission dip stick and tube

assembly.

24.
Disconnect transmission vacuum modulator line at

distributor advance line tee.

25.
Position transmission hoist under transmission and

attach safety chain to transmission.

26.
Remove transmission converter housing-to-engine

attaching foolts and slide transmission rearward.
NOTE:
Observe converter when moving trans-

mission rearward. If converter does not move

with the transmission, pry it free of flywheel

before proceeding.

27.
Install converter retaining strap.

28.
Lower and remove transmission from vehicle by

tilting the front down and to the right while inter-

mittently lowering the transmission to facilitate its

• removal.

29.
Reinstall transmission assembly by performing the

above steps in reverse order.

Bolt Torques

Transmission Case to Flywheel

Housing Bolts 35 ft. lbs.

Converter to Flywheel Bolts. . , . . 35 ft. lbs.

OTHER SERVICE OPERATIONS

Although certain operations, such as oil pan or gasket

replacement, valve body, governor, filler pipe "O" ring,

speedometer drive gear, case extension "0" ring and

rear oil seal, vacuum modulator, and servo cover or

gasket service may be performed from underneath the
vehicle without removing the Powerglide; their service

procedure is covered in the Passenger Overhaul Manual

and is not repeated here. Refer to the- Powerglide Sec-

tion of the Passenger Overhaul Manual for all other

service operations not covered here.

DIAGNOSIS

Proper operation of the Powerglide transmission may

be affected by a number of factors, all of which must be

considered when trouble in the unit is diagnosed.

Proper trouble diagnosis can only be accomplished

when performed in a thorough step by step procedure.

The following procedure has been devised and tested and

is recommended for all trouble diagnosis complaints and

if the service man will follow this checking procedure,

accurate and dependable diagnosis may be accomplished.

This will result in a savings of time, not only to the

service man, but to the customer as well.

WARMING UP TRANSMISSION

Before attempting to check and/or correct any com-

plaints on the Powerglide transmission it is absolutely

essential that the oil level be checked and corrected if

necessary. An oil level which is either too high or too

low can be the cause of a number of abnormal conditions

from excessive noise to slippage in all ranges.

It must be remembered that cold oil will slow up the

action of the hydraulic controls in the transmission. For

this reason a trouble or oil leak diagnosis should not be

attempted until the transmission has been warmed up by

either of the following procedures:

Shop Warm Up

1.
Connect tachometer to engine.

2.
Set parking brake tight and start engine.

3.
Place selector light in
"D"
(drive) range.

4.
Adjust carburetor idle speed adjusting screw to run

engine at approximately 750 rpm and operate in this

manner for two minutes. At the end of two minutes

of operation, the transmission will be sufficiently

warmed up for diagnosis purposes.
NOTE:
At this point, readjust the engine idle

speed to 450-475 rpm in
"D"
range.

Road Warm Up

Drive the car approximately 5 miles with frequent

starts and stops.

NOTE:
At this point, make sure the engine idle

speed is set to 450-475 rpm in
"D"
range.

CHECKING FLUID LEVEL AND CONDITION

After transmission has been warmed up, check the

fluid level with the engine idling, parking brake set and

control lever in "N" (neutral). If the fluid level is low,

add fluid to bring level up to the full mark on gauge rod,

CAUTION: If fluid level is too high, fluid may

be aerated by the planet carrier. Aerated fluid

will cause turbulence in the converter which will

result in lost power, lower stall speed and lower

pressures in control circuits. Lower fluid level

to full mark, then shut off engine to allow air

bubbles to work out of fluid.

When checking oil level, aburned smell and discolora-

tion indicate burned clutches or bands and the transmis-

sion will have to be removed.

MANUAL LINKAGE

Manual linkage adjustment and the associated neutral

safety switch are important from a safety standpoint.

The neutral safety switch should be adjusted so that the

engine will start in the Park and Neutral positions only.

With the selector lever in the Park position, the park-

ing pawl should freely engage and prevent the vehicle

CHEVROLET CHASSIS SERVICE MANUAL