head light CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

GENERAL INFORMATION 0-7

a vise using leather or wood on each side to prevent

damage to the cylinder,

7. Stake the retainer securely in place by staking the

cylinder metal over both edges of the retainer ends

using a suitable staking tool at right angles to the

top of the retainer and from the cast metal of the

cylinder over the retainer at each corner.

PUSHING, TOWING AND LIFTING

Pushing

NOTE:
Towing car to start is not recommended

due to the possibility of the disabled car ac-

celerating into tow car.

AUTOMATIC TRANSMISSION

Do not attempt to start the engine by pushing the car.

Should the battery become discharged, it will be neces-

sary to use an auxiliary battery with jumper cables to

start the engine.

CAUTION: To prevent damage to electrical

system, never connect booster batteries in ex-
cess of 12 volts and connect positive to positive

and negative to negative.

Manual Transmission

When a push start is necessary turn off all electrical

loads such as heater, radio, and if possible, lights, turn

on the key, depress the clutch, and place the shift lever

in high gear. Release the clutch when your speed reaches

10 to 15 miles per hour.

TOWING

The car may be towed safely on its rear wheels with

the (selector lever in "N" (Neutral) position at speeds

of 35 miles per hour or less under most conditions.

However, the drive shaft must be disconnected or the

car towed on its front wheels if 1) Tow speeds in excess

of 35 MPH are necessary, 2) Car must be towed for ex-

tended distances (over 50 miles) or, 3) Transmission is

not operating properly. If car is towed on its front

wheels, the steering wheel should be secured to maintain

a straight ahead position.

DRIVE ON HOIST

BUMPER JACK LIFTING AT FRAME ATTACHMENT ONLY

FLOOR JACK OR HOIST LIFT

Fig.
21-Vehicle Lifting Pointe-Chevroiet

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-30

Leak Detector

Tool J-6084 (fig. 43) is a propane gas-burning torch

which is used to locate a leak in any part of the system.

Refrigerant gas drawn into the sampling tube attached to

the torch will cause the torch flame to change color in

proportion to the size of the leak. Propane gas fuel

cylinders used with the torch are readily available

commercially throughout the country.

CAUTION: Do not use lighted detector in any

place where combustible or explosive gases,

dusts or vapors may be present;

Operating Detector

1.
Open control valve only until a low hiss of gas is

heard, then light gas at opening in chimney.

2.
Adjust flame until desired volume is obtained. This

is most satisfactory when blue flame is approxi-

mately 3/8" above reactor plate. The reaction plate

will quickly heat to a cherry red.

3.
Explore for leaks by moving the end of the sampling

hose around possible leak points in the system. Do

not pinch or kink hose.

NOTE: Since R-12 is heavier than air, it is

good practice to place open end of sampling tube

immediately below point being tested, partic-

ularly in cases of small leaks.

CAUTION: Do not breathe the fumes that are

produced by the burning of R-12 gas in the de-

tector flame, since such fumes can be toxic in

large concentrations of R?»12.

4.
Watch for color changes. The color of the flame

which passes through the reaction plate will change

to yellow when sampling hose draws in very small

CHIMNEY

REACTION PLATE

BURNER HEAD

Fig.
43—Leak Detector
leaks of R-12. Large leaks will be indicated by a

change in color to a vivid purplish-blue. When the

sampling hose passes the leak, the flame will clear

to an almost colorless pale-blue again. If the flame

remains yellow when unit is removed from leak,

insufficient air is being drawn in or the reaction

plate is dirty.

NOTE: A refrigerant leak in the high pressure

side of the system may be more easily detected

when, if possible, the system is in operation. A

leak on the low pressure side may be most

easily detected after the engine has been shut

off for several minutes to allow system pres-

sures to equalize. This particularly applies to

the front seal.

VACUUM PUMP

A vacuum pump should be used for evacuating air and

moisture from the air conditioning system.

Vacuum pump, Tool J-5428, (fig.. 44) is available for

this purpose. It is used as a component part of the

Charging Station J-8393, described previously. The fol-

lowing precautions should be observed relative to tbe

operation and maintenance of this pump.

' • Make sure dust cap on discharge outlet of vacuum

pump is removed before operating.

• Keep all openings capped when not in use to avoid

moisture being drawn into the system.

• Oil should be changed after every 250 hours of nor-

mal operation.

To change oil, simply unscrew hex nut located on

back side of pump, tilt backward and drain out oil

(fig. 44). Recharge with 8 ounces of vacuum pump

oil.
If you desire to flush out the pump, use this

same type clean oil. Do not use solvent.

NOTE: Improper lubrication will shorten the

life of pump.

• If this pump is subjected to extreme or prolonged

cold, allow it to remain indoors until oil has reached

approximate room temperature. Failure to warm oil

will result in a blown fuse.

• A five ampere time delay cartridge fuse has been

installed in the common line to protect the windings

of the compressor. The fuse will blow if an ex-

cessive load is placed on the pump. In the event the

fuse is blown, replace with a five ampere time delay

fuse - do not use a substitute fuse as it will result in

damage to the starting windings.

• If the pump is being utilized to evacuate a burnt-out

system, a filter must be connected to the intake

fitting to prevent any sludge from contaminating the

working parts, which will result in malfunction of the

pump.

• Do not use the vacuum pump as an air compressor.

AVAILABILITY OF REFRIGERANT-12

Refrigerant-12 is available through Parts Stock in 25

lb.
drums and in 15 oz. disposable cans. Valves are

available for
the"
disposable cans, which may be used as

individual cans or as a group of up to four cans (fig. 45).

Tool J-6272 is used with one through four cans. The

use of the four-can fixture makes it possible to charge

the system with a known quantity of refrigerant without

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY 1B-29

CUSHION

CUSHION ASNi.^ty** ACCESS

#2 BODY BRACKET

( 67 ONLY)
SHIM

( 37 POSITION).

CUSHION ASM.

( 37)

SHIM

( 67 POSITION)

CUSHION

( 37 ONLY)

#1 BODY BRACKET

Fig.
65—Body Mounts

PRECAUTIONS

Creams are available to protect the skin from a con-

dition known as occupational, or contact dermatitis. This

common type of dermatitis is not contagious. Improved

resin formulas in the approved kits have almost elimi-

nated skin irritation. Cream is supplied with the kit for

men who may have a tendency toward skin irritation

from the resins or dust.

The application of these creams is recommended

whenever the Resin Kit materials are used. Generally,

the cream is not required when the plastic solder kit is

being used. Directions for using the cream is as follows:

a. Wash hands clean. Dry thoroughly.

b.
Squeeze about 1/2 inch (or 1/2 teaspoonful) of

#71 cream into palm of hand.

c. Spread evenly and lightly until cream disappears.

Work cream into cuticle, between fingers and

around wrists.

d. Apply second coat, repeating Steps b and c.

e. Hold hands briefly under cold running water to

set cream.

2.
Remove resin mixture from hands as soon as possi-

ble and imperatively before mixture starts to gel.

This can be observed by the action of the material

being used. Resin may be removed with lacquer

thinner by washing in soap and water.

3.
Respirators are recommended when grinding. Also

some minor skin irritation from glass and powdered

cured resin may be evident. Washing in cold water

will help to minimize.

4.
Use a belt sander with a vacuum attachment for dust

control if possible.
5. Resin mixtures may produce toxic fumes and should

be used in well ventilated areas.

6. Be careful not to get any resin material on clothing.

7. Use the right materials for the job. It is important

to use the approved kits because Chevrolet's rigid

quality standards assure you the right material to

do the job. Other materials available may not meet

the required engineering and safety standards.

8. Keep the materials, utensils and work area clean

and dry. These repairs involve chemical reactions,

and dirt or moisture may upset the chemical bal-

ances and produce unsatisfactory results.

9. Before starting repair operations, look for hidden

damage by applying pressure around the damaged

area, looking for hairline cracks and other breakage.

Check for minor damage at other points in the vehi-

cle such as around exhaust pipes, grille, headlamps

and points of wear or rub. Early repair of this

minor damage may prevent major repair later.

PLASTIC SOLDER
KIT

The Plastic Solder Repair Kit is used for minor re-

pairs on the Corvette body. These materials will produce

an easy, quick and lasting repair in the case of small

cracks, surface imperfections and small holes.

1.
Use paint remover or power sander, and remove

finish from damaged area. Carefully inspect for

other areas requiring repair.

2.
Mix the materials (fig. 72).

3.
Apply the material, using a putty knife or rubber

squeegee, Figure 73. Work the material into the

repair and build the material up to the desired

CHEVROLET CHASSIS SERVICE

CORVETTE BODY
1B-47

REAR

BOW

ASSY.

VIEW
C

Fig.
101—Folding
Top
Adjustments

MATERIAL
FOR
ATTACHMENT

FRONT HEADER PANEL

PAD
WIRE-ON

BINDING

WINDOW

EXTENS

SECTION
E-E

AY STRAP

SECTION

A-A

CEMENT SECURELY

REAR RAIL ONLY

Fig.
102—Folding
Top
Trim Installation

1.
To
remove superficial dust,
do not use a
dry cloth.

Use
a
soft cotton cloth moistened with water
and

wipe cross-wise
of
the window.

2.
To
wash
the
rear window,
use
cold or tepid (not hot)
water
and a
mild neutral soap suds. After washing,

rinse with clear water
and
wipe with
a
slightly

moistened clean soft cloth.
A
high quality plastic

window cleaner
is
available from Chevrolet parts

sources.

CHEVROLET
Oi
SERVia

CORVETTE BODY 1B-52

and pull weatherstrip and trim from rear bow.

Section A-A shows installed position of these com-

ponents. Refer also to figure 105.

installation

1.
Find and mark center of header, #3 bow, rear bow

and leading and trailing edges of top trim. Align

these marks during installation and recheck their

alignment from time to time while installation is in

progress, especially during tacking or stapling.

2.
Assemble top trim and weatherstrip to rear bow,

referring to Section A-A and Figure 105. Note that

filler strip locks this assembly together and goes

in last. Align center marks.

3.
If new pads are required, install at this time, align-

ing with marks made when old pads were removed.

Figure 106 shows pad construction; Figure 107 shows

pad installed.

4.
Install top trim-rear bow assembly on top frame

with four screws removed at disassembly.

5.
Lock down rear bow in desired "top up" position.

Pull up stay straps and staple or tack to #3 bow

(fig. 108).

6. Pull leading edge of trim iip to header and align

center marks. Smooth out fabric and clamp, tack

or staple temporarily to header.

7.
Draw window extension up to #3 bow, aligning cen-

tering marks. Turn an ample amount of fabric under

and tack to #3 bow. Apply neoprene trim cement,

GM Part #3695016 or equivalent, to area shown in

View D of Figure 102. Follow directions on package.

8. Draw roof portion of trim over #3 bow, align marks

and tack on staple.

9. Trim off excess material and install wire-on binding

as shown in Figure 109 and View D of Figure 102.

Install binding caps.

10.
Remove temporary clamps or fastenings holding trim

to header.

11.
With header locked down, pull trim assembly up tight

and mark for final installation.

12.
Apply trim cement to header and rear side rail.

13.
Release header from windshield. Tack or staple trim

to header (fig. 103).

14.
Apply trim to rear side frame, previously cemented.

15.
Install weatherstrips which were removed at dis-

assembly and install retaining screws in header

weatherstrip.

16.
Make any adjustments necessary, following instruc-

tions listed under Folding Top—Adjustments.

FRAME AND LINKAGE

Figure 110 illustrates construction features of the

folding top frame and linkage. Various cross sections in

Figure 110 show the pivoting joints and their assembly.

If an operation is being performed which requires

removal of folding top trim, follow directions in this

section. The entire frame assembly may be removed and

replaced as a unit. Follow instructions for Folding Top

Trim and Rear Window Assembly and Top Assembly—

Removal and Installation.

The pivoting joints should be lubricated with light

machine oil once a year. Apply oil sparingly so as not

to stain top trim.
WEATHERSTRIP

Side Rail Weatherstrip

Figure 111 illustrates installation of side rail weather-

strip which acts to seal window opening. The weather-

strip is held in place by studs which are part of the

weatherstrip assembly, and by neoprene base cement

which is applied between weatherstrip and side rail

surface.

When replacing weatherstrip remove all rust, old

cement and foreign material from the surfaces to be

cemented, to assure successful bonding. Use only good

quality neoprene cement suitable for weatherstrip

application.

Header Weatherstrip

Weatherstrip assembly is retained to the header panel

by a combination of studs, sheet metal screws and special

fasteners as shown in Figure 112, along with neoprene

base weatherstrip cement.

Figure 99 shows' a cross section of weatherstrip taken

through a special fastener. To replace fastener, rotate

ninety degrees to align fastener head with slot. Follow

directions for cementing in the Side Rail Weatherstrip

instructions preceding this write up.

ADDING HARDTOP (ROOF PANEL ASSEMBLY)

An available roof panel assembly (hardtop) complete

can be added to convertible model Corvettes. The hard-

ware is included with the panel assembly.

Reworking of a plastic part (one for each side of the

roof panel) can be used as a marker for drilling of two

required holes in the folding top compartment lid* Hard-

ware is attached at four locations — two on the lid and

two (one each side) at the lock pillar area as follows:

1.
Rework two plastic retainers (#6280765) (used on

Chevrolet and Corvair door inner panels for trim

retention) as shown by Figure 113.

2.
Slide the reworked plastic retainers into the bolt re-

tainer slots on each side of the hardtop rear bow

(position plastic tip inboard).

3.
Mark the hardtop reveal molding at the approximate

location of the two plastic retainers,

4.
Mark the tips of the two plastic retainers with a

china marker pencil.

5.
Close the soft top compartment lid.

6. With aid of an ^assistant, position front of hardtop

onto header and lower onto vehicle. Do not fasten

latches at windshield header.

7.
Apply hand pressure at reveal molding marks.

8. Mark roof panel attachment hole location at each

lock pillar area (fig. 114).

9. With aid of an assistant, lift roof panel straight up

off body and set roof panel aside.

10.
Mark the drill position at the four china marks with

a center punch.

11.
Place a 2" x 4" board under the top compartment lid

to prevent drill damage to folding top material. Make

certain the compartment lid is securely locked

before drilling.

12.
Drill 1/8" pilot hole at the 4 marked locations.

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-8

REPAIR PROCEDURES

Unless otherwise indicated all repair procedures will

apply to all five vehicles covered in this manual.

CAUTION: During any operations which in-

clude breaking the ball stud loose from the

knuckle boss extreme care must be used to as-

sure that the ball stud seal is not damaged or

cut. A recommended way to loosen the stud is to

place a flat bar stock against the knuckle boss

and strike the bar rather than the knuckle.

FRONT BRAKE DRUM-CHEVROLET, CAMARO,

CHEVELLE, CHEVY It

Removal

1.
Remove hub caps, partially loosen wheel nuts and

raise vehicle from floor. Remove wheel nuts and

wheel.

2.
Remove brake drum. In some cases it may be nec-

essary to back off brake adjustment because of

scored drum or unevenly worn brake linings.

3.
Check brake drum for concentricity, damaged pilot

diameter or scored braking surface. Lightly sand

braking surface and wipe clean.

Installation

1.
Install drum over hub bolts making sure alignment

dowel on drum web indexes with hole in wheel hub.

This will assure proper drum alignment with hub

bolts and hub pilot diameter.

2.
Install wheel and partially tighten wheel nuts.

3.
Re-adjust brake shoes to original setting. It may be

necessary to re-adjust brake shoes on both front

and/or rear wheels to assure balanced brake adjust-

ment. See Section 5 for brake adjustment procedure.

4.
Lower vehicle to floor, tighten hub wheel nuts and in-

stall hub cap.

FRONT WHEEL HUB

Replacement

1.
Remove hub caps, break loose the wheel stud nuts
VM" DIA. PIPE OR ARBOR

>l

INNER CUP

OUTER CUP
JL
RADIUS

e^

Fig.
10 - Pressing Front Hub Bolts (Typical)
Fig.
11 - Front Wheel Bearing Cop Removers

and raise vehicle. Remove wheel nuts, wheel and

tire and brake drum or (on Corvette) brake caliper

and brake disc.

NOTE:
On the Corvette, the hub and brake disc

are serviced as a complete assembly.

2.
Pry out hub grease cap, cotter pin, spindle nut and

washer,
and
remove hub. Do not drop wheel bearings.

3.
Reverse this procedure to install.

Replacement of Wheel Hub Bolts

It may be necessary to replace damaged wheel hub

bolts.
In this case, service the hub in the following

manner.

1.
Remove the hub bolts with a press or hammer.

These bolts are not peened into the hub. Do not

damage wheel mounting surface on hub flange.

2.
Install new serrated bolt into hole in
hub.
Tap lightly

with a hammer to start bolt serrations in hole, mak-

ing sure that bolt is square with hub flange.

3.
Press bolt into flange until head is fully seated

against hub flange (fig. 10).

FRONT WHEEL BEARINGS

Removal '

1.
Remove wheel hub as described above.

NOTE: Discard cotter pin. Install new cotter

pin when assembling.

2.
Remove outer roller bearing assembly from hub with

fingers. The inner bearing assembly will remain in

the hub and may be removed after prying out the

inner bearing lip seal assembly. Discard seal.

3.
Wash all parts thoroughly in cleaning solvent and

blow dry.

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-15

4.
Insert Spring Compressor J-
6874-
4-
5 with Adapters

J-6874-8-9 into upp^r spring tower so that lower

MU"
bolt fits into shock absorber mounting holes in

spring seat (fig. 23). Secure the two lower studs to

the spring seat with nuts.

5.
Fit the tool upper pilot to top of spring and compress

spring by tightening upper nut (fig. 24). Compress

spring until screw is bottomed out.

6. Remove lower spring seat retaining nuts, lift spring

and seat assembly from control arm and guide it

down and out through fender skirt (fig. 25).

Spring Seat Replacement (Fig. 26)

1.
Release spring tension and disconnect spring com-

pressor from spring seat.

2.
Install new spring seat to spring compressor.

Installation

1.
If spring is to be replaced, install new spring into

tool and compress spring until screw is bottomed

out.

NOTE: Spring coil ends must be against spring

stops in upper and lower seats.

2.
Lift spring and tool assembly into place and position

so that the upper spring stop is inboard.

NOTE: Locating tab on upper spring seat may

be flattened before reinstalling spring.

3.
Install lower spring seat to control arm and torque

nuts as shown in the Specifications.

4.
Loosen spring compressor until spring is properly

seated in upper spring tower and remove.

5.
Install shock abosrber as outlined under Shock Ab-

sorber—Installation in this section.

Corvette

Removal

1.
With car on suitable hoist or jack, (support vehicle

by frame so control arms may swing free) remove

wheel and tire assembly, stabilizer bar and shock

absorber. Loosen the lower ball joint to steering

knuckle nut, and the' two lower control arm cross

shaft bushing bolts.

2.
Place Tool J-6874-1 across top of sixth coil (ap-

prox.),
then loosely secure Tool J-6874-2 to the up-

per shoe, with attaching capscrews and lock washers.

The upper shoe "V" notch and lower shoe raised land

should contact spring.

3.
Insert Tool J-6874 up through center of spring and

attach to upper and lower shoe assembly.

4.
Position spacers under shock absorber mounting hole

and against bottom of lower control arm. Install

special bearing washer and Tool J-6874-5. Locate

bearing against spacer and large washer against

bearing. Feed screw up through large washer bear-

ing and spacer and thread into Tool J-6874 and

tighten snugly (fig. 22).

5.
Center shoe assembly on spring and tighten screw

until a very slight compression is placed on spring

(fig. '22). Then firmly tighten down the two cap-

screws securing the upper and lower shoes to lock

these shoes to spring.

6. Turn head of screw until spring is compressed just

enough to clear the spring tower, then remove the

lower ball joint to steering knuckle nut (fig. 22).
NOTE: It may be necessary to assist the

spring out of the spring tower with a pry bar or

a similar tool.

7.
Disconnect the lower ball joint from the steering

knuckle and lower the control arm with the com-

pressed spring. Immediately release compression

on spring by backing off long screw. Release spring

and tool and withdraw spring.

CAUTION: The spring force under compres-

sion is very large. Exercise every safety pre-

caution when performing this operation to see

that individuals and materials subject to damage

are removed from the path of the spring when

the control arm is being lowered. Also, the

compressed spring
be relaxed immedi-

ately after lowering the control arm to reduce

the time of exposure to the large compressive

force.

Installation

1.
Position spring with closely coiled end up. Place

Tool J-6874-1 across the top of the sixth coil (ap-

prox.) then loosely secure Tool J-6874-2 to the

upper shoe with attaching capscrews and lock wash-

ers.
The upper shoe MV" notch and lower shoe

raised land should contact spring.

2.
Insert Tool J-6874 up through center of spring and

attach to upper and lower shoe assembly with bolt

and nut.

3.
Set spring in its seat on the lower control arm.

4.
Position spacers centrally under shock absorber

mounting hole and against bottom of lower control

arm. Install bearing, large washer and Tool

J-6874-5.
Locate bearing against spacer and large

washer against bearing. Feed the screw up through

large washer, bearing and spacer and thread into

yoke rod. Tighten snugly, but do not start to draw

down yet

5.
Center the shoe assembly on the spring and tighten

the lag screw until a very slight compression is

placed on spring, then firmly tighten down the two

capscrews securing the upper and lower shoes. This

will lock the shoes to the coil spring.

6. Turn head of screw until spring is compressed just

enough to clear the spring tower.

NOTE: It may be necessary to assist the

spring into the spring tower with a pry bar or

similar tool.

7.
Immediately install the lower ball joint into steering

knuckle and secure in place with attaching nut.

8. Release compression on spring and at the same time

use a drift to guide the coil spring into its proper

seat. End of coils must be 3/8" from coil stops in

spring seat.

9. Tighten the lower ball joint to steering knuckle nut

and lock with cotter key.

10.
Install shock absorber and stabilizer bar.

11.
Install wheel, tire and drum assembly.

12.
Remove car from hoist or jack stands.

13.
Tighten the two lower control cross shaft bushing

bolts to 45-55 lbs. ft. torque.

NOTE: If a suitable adjustable jack-stand is

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-21

Chevy II

Removal

1.
Support control arm on Tool J-7 574-4 and insert

Spacer J-9514 (fig. 34).

2,
Press bushing out with Tool J-9226 and Handle

J-7079-2 (fig. 34).

Installation

With Spacer J-9514 still in control arm, invert control

arm and press in new bushing with Tool, J-7474-2 and

Handle J-7079-2 until bushing is fully seated.

CAUTION: It should be noted that control arm

bushing diameters are unequal and bushing must

be pressed into position through larger diameter

only.

CROSS SHAFT AND/ON BUSHINGS

Corvette

Removal

1.
Remove bolt, lock washer and collar from each end

of cross shaft.

2.
Thread a 7/16 x 20 capscrew (furnished with Tool

J-5888) to the bottom of the threads in one end of the

cross shaft.

3.
Support control arm in an arbor press on Tool

J-5888-3,
as shown in Figure 35.

NOTE:
Be certain bushing flange does not

contact support.

4.
Press on cap screw until bushing is free of control

arm. Discard bushing.

5. Remove cap screw from cross shaft. Insert it in

other end of shaft. Invert control arm on support.

Again be certain bushing flange does not contact

support.

6. Press on cap screw until bushing is free of control

arm. Discard bushing.

Installation

1.
With cross shaft in control arm and Tool J-7052-1

in position, place control arm on Tool J-5888-3.

Hand start bushing into control arm and over end of

cross shaft.

NOTE:
The end of the shaft with the two bolt

holes should be toward front of control arm.

2.
Install Tool J-7052-5 over bushing. Be certain

three-piece spacer is not over-lapping bushing holes

in control arm.

3.
Press bushing into control arm until flange contacts

control arm (fig. 36).

4.
Invert arm in press and repeat the process on the

other bushing. After installation, cross shaft should

be free enough to be rotated by hand.

5. Install collar, lock washer and cap screw in each end

of cross shaft. Tighten to torque shown in Specifica-

tions after spring installation.
UPPER CONTROL ARM SPHERICAL JOINT

Chevrolet, Chevelle, Comoro and Corvette

Inspection

The upper spherical joint is checked for wear by

checking the torque required to rotate the ball stud in the

assembly. After performing the first four steps under

"Replacement" below, install a stud nut on the stud and

measure the torque required to turn the stud in the as-

sembly with a torque wrench. Specified torque for a new

joint is 9 lbs. ft. If torque readings are excessively

high or low, replace the ball joint. If excessive wear is

indicated in upper joint, both upper and lower joints

should be replaced.

NOTE:
This inspection does not necessitate

upper control arm removal.

Replacement

1.
Support the vehicle weight at the outer end of the

lower control arm.

2.
Remove the wheel and tire assembly.

3.
Remove cotter pin and nut from upper control arm

ball stud.

4.
Remove the stud from knuckle.

5. Cut off the ball joint rivets with a chisel.

6. Install new joint and retain in place with the special

nuts and bolts supplied.

7. Reassemble ball stud to the steering knuckle.

Chevy II

Inspection

The following on-the-vehicle check is to determine ball

joint wear.

NOTE:
The upper ball joint is a loose fit when

not connected to the steering knuckle. Wear may

be checked without disassembling the ball stud

by
using'
the following procedure:

1.
While vehicle weight is still on front wheels, insert

upper control arm support as shown in Figure 14.

2.
Raise vehicle and allow wheel and tire to hang free.

3.
Measure distance from tip of ball stud to top surface

of control arm.

4.
Place adjustable jackstand under tire and raise

slightly to take up ball joint looseness.

5. Repeat Step 3 and if the difference in measurements

exceeds 3/32", the joint is excessively worn and

should be replaced.

Replacement

1.
With vehicle weight still on front wheels, install

spacer between upper control arm and frame side

rail (fig. 15). Raise vehicle.

2.
Remove wheel and tire.

3.
Disconnect stabilizer link (if present) and strut rod

at lower control arm.

4.
Remove cotter pin and nut from upper ball joint stud.

5. Break ball stud loose. Drop lower control arm,

steering knuckle and brake assembly with an adjust-

able jackstand until upper control arm ball joint is

easily accessible.

6. Using a large chisel, cut off the three ball joint re-

taining plate rivet heads. It may be necessary to

drill out rivet heads before chiseling.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-16

5.
Adjust ignition timing and carburetor idle speed and

mixture.

VALVE STEM OIL SEAL AND/OR VALVE SPRING

Replacement

1.
Remove rocker arm cover as outlined.

2.
Remove spark plug, rocker arm and push rod on the

cylinder(s) to be serviced.

3.
Apply compressed air to the spark plug hole to hold

the valves in place.

NOTE: A tool to apply air to the cylinder is

available through local jobbers or may be manu-

factured. In manufacturing this Tool a AC-46N

Spark Plug or its equivalent is recommended.

This will make the Tool universal for all

Chevrolet engines. Chisel the spark plug as

shown, then drive the porcelain out of the plug

by tapping the center electrode against a hard

block. Using a 3/8" pipe tap, cut threads in the

remaining portion of the spark ^>lug and assem-

ble as shown (fig. 3L).

4.
Using Tool J-5892 to compress the valve spring, re-

move the valve locks, valve cap, valve shield and

valve spring and damper (fig. 4L).

5.
Remove the valve stem oil seal.

6. To replace, set the valve spring and damper, valve

shield and valve cap in place. The close coiled end

of the spring is installed against the cylinder head.

Compress the spring with
Too^
J-5892 and install oil

seal in the lower groove of the stem, making sure the

seal'is flat and not twisted.

NOTE: A light coat of oil on the seal will help

prevent twisting.

7.
Install the valve locks and release the compressor

tool, making sure the locks seat properly in the

upper groove of the valve stem.

NOTE: Grease may be used to hold the locks

in place while releasing the compressor tool.

8. Install spark plug, using a new gasket, and torque to

specifications.

9. Install and adjust valve mechanism as outlined.

CYLINDER HEAD ASSEMBLY

Removal

1.
Remove manifold assembly as. outlined.

2.
Remove valve mechanism as outlined.

3.
Drain cooling system (block).

4.
Remove fuel and vacuum line from retaining clip at

water outlet then disconnect wires from temperature

sending units.

5.
Disconnect upper radiator hose at water outlet hous-

ing and battery ground strap at cylinder head.

6. Remove coil (L6 engines only).

7.
Remove cylinder head bolts, cylinder head and gas-

ket. Place cylinder head on two blocks of wood to

prevent damage.

Installation

CAUTION: The gasket surfaces on both the

head and the block must be clean of any foreign
matter and free of nicks or heavy scratches.

Cylinder bolt threads in the block and threads

on the cylinder head bolt must be cleaned. (Dirt

will affect bolt torque.) Do not use gasket sealer

on composition steel asbestos gasket.

Fig. 3L -
AIF
Adapter Tool

1.
Place the gasket in position over the dowel pins with

the bead up.

2.
Carefully guide cylinder head into place over dowel

pins and gasket.

3.
Coat threads of cylinder head bolts with sealing com-

pound and install finger tight.

4.
Tighten cylinder head bolts a little at a time in the

sequence shown on the torque sequence chart until

the specified torque is reached.

5.
Install coil (if removed).

6. Connect upper radiator hose and engine ground strap.

7.
Connect temperature sending unit wires and install

fuel and vacuum lines in clip at water outlet.

8. Fill cooling system.
•

9. Install manifold assembly as outlined.

10.
Install and adjust valve mechanism as outlined.

Fig.
4L
- Compressing Valve Spring

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-29

an extent that the return spring can no longer push

the plunger back up to working position. Probable

causes are:

a. Excessive varnish or carbon deposit causing ab-

normal stickiness.

b.
(Sailing or "pick-up" between plunger and bore of

lifter body, usually caused by an abrasive piece of

dirt or metal wedging between plunger and lifter

body.

2.
Moderate Rapping Noise--Probable causes are:

a. Excessively high leakdown rate.

b.
Leaky check valve seat.

c. Improper adjustment.

3.
General Noise Throughout the Valve Train-rThis

will, in almost all cases, be a definite indication of

insufficient oil supply, or improper adjustment.

4.
Intermittent Clicking—Probable causes are:

a. A microscopic piece of dirt momentarily caught

between ball seat and check valve ball.

b.
In rare cases, the ball itself may be out-of-round

or have a flat spot.

c. Improper adjustment.

In most cases where noise exists in one or more lifters

all lifter units should be removed, disassembled, cleaned

in a solvent, reassembled, and reinstalled in the engine.

If dirt, corrosion, carbon, etc. is shown to exist in one

unit, it more than likely exists in all the units, thus it

would only be a matter of time before all lifters caused

trouble.

Removal

1.
Remove intake manifold as outlined.

2.
Remove valve mechanism as outlined.

3.
Remove valve lifters.

NOTE: Place valve lifters in a rack so they

may be reinstalled in the same location.

Installation

1.
Install valve lifters.

NOTE: Whenever new valve lifters are being

installed coat foot of valve lifters with Molykote

or its equivalent.

2.
Install intake manifold as outlined.

3.
Install and adjust valve mechanism as outlined.

VALVE STEM OIL SEAL AND/OR VALVE SPRING

Replacement

1.
Remove rocker arm cover(s) as outlined.

2.
Remove spark plug, rocker arm and push rod on the

cylinders to be serviced.

3.
Apply compressed air to the spark plug hole to hold

tl*e valves in place.

NOTE: A tool to apply air to the cylinder is

available through local jobbers or may be manu-

factured. In manufacturing this Tool a AC-46N

Spark Plug or its equivalent is recommended.

This will make the Tool universal for all

Chevrolet engines. Chisel the spark plug as

shown, then drive the porcelain out of the plug

by tapping the center electrode against a hard

block. Using a 3/8" pipe tap, cut threads in the

remaining portion of the spark plug and assem-

ble as shown (fig. 6V).
Fig.
6V - Air Adapter Tool

4.
Using Tool J-5892, to compress the valve spring, re-

move the valve locks, valve cap, and valve spring and

damper (fig. 7V).

5.
Remove valve stem oil seal.

6. Remove as follows:

283, 327 and 350 eu. in.
Engines

a. To replace, set the valve spring and damper,

valve shield and valve cap in place. The close

coiled end of the spring is installed against the

cylinder head.

b.
Compress the spring with Tool J-5892 and install

oil seal in the lower groove of the stem, making

sure the seal is flat and not twisted.

NOTE: A light coat of oil on the seal will help

prevent twisting.

Fig.
7V - Compressing Valve Spring

CHEVROLET CHASSIS SERVICE MANUAL