jump start CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

GENERAL INFORMATION 0-7

a vise using leather or wood on each side to prevent

damage to the cylinder,

7. Stake the retainer securely in place by staking the

cylinder metal over both edges of the retainer ends

using a suitable staking tool at right angles to the

top of the retainer and from the cast metal of the

cylinder over the retainer at each corner.

PUSHING, TOWING AND LIFTING

Pushing

NOTE:
Towing car to start is not recommended

due to the possibility of the disabled car ac-

celerating into tow car.

AUTOMATIC TRANSMISSION

Do not attempt to start the engine by pushing the car.

Should the battery become discharged, it will be neces-

sary to use an auxiliary battery with jumper cables to

start the engine.

CAUTION: To prevent damage to electrical

system, never connect booster batteries in ex-
cess of 12 volts and connect positive to positive

and negative to negative.

Manual Transmission

When a push start is necessary turn off all electrical

loads such as heater, radio, and if possible, lights, turn

on the key, depress the clutch, and place the shift lever

in high gear. Release the clutch when your speed reaches

10 to 15 miles per hour.

TOWING

The car may be towed safely on its rear wheels with

the (selector lever in "N" (Neutral) position at speeds

of 35 miles per hour or less under most conditions.

However, the drive shaft must be disconnected or the

car towed on its front wheels if 1) Tow speeds in excess

of 35 MPH are necessary, 2) Car must be towed for ex-

tended distances (over 50 miles) or, 3) Transmission is

not operating properly. If car is towed on its front

wheels, the steering wheel should be secured to maintain

a straight ahead position.

DRIVE ON HOIST

BUMPER JACK LIFTING AT FRAME ATTACHMENT ONLY

FLOOR JACK OR HOIST LIFT

Fig.
21-Vehicle Lifting Pointe-Chevroiet

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-2

remotely at the starter, with a special jumper

cable or other means, the primary distributor

lead must be disconnected from the negative

post on the coil and the ignition switch must be

in the "ON" position. Failure to do this will

result in a damaged grounding circuit in the

ignition switch.

3.
Crank engine through at least four compression

strokes to obtain highest possible reading.

4.
Check and record compression of each cylinder.

5.
If one or more cylinders read low tor uneven, inject

about a tablespoon of engine oil on top of pistons

in low reading cylinders (through spark plug

port).
Crank engine several times and recheck

compression.

• If compression comes up but does not necessarily

reach normal, rings are worn.

• If compression does not improve, valves are

burnt, sticking or not seating properly.

• If two adjacent cylinders indicate low compres-

sion and injecting oil does not increase compres-

sion, the cause may be a head gasket leak between

the cylinders. Engine coolant and/or oil in cylin-

ders could result from this defect.

NOTE: If a weak cylinder cannot be located

with the compression check, see "Cylinder Bal-

ance Test" under "Additional Checks and Adjust-

ments" in this section.

Service and Install Spark Plugs (Fig. 2)

1.
Inspect each plug individually for badly worn elec-

trodes,
glazed, broken or blistered porcelains and

replace plugs where necessary. Refer to spark plug

diagnosis information presented in Section 6Y for an

analysis of plug conditions.

2.
Clean serviceable spark plugs thoroughly, using an

abrasive-type cleaner such as sand blast. File the

center electrode flat.

3.
Inspect each spark plug for make and heat range. All

plugs must be of the same make and number.

4.
Adjust spark plug gaps to specifications using a

round feeler gauge.
PORCELAIN

INSULATOR

INSULATOR CRACKS

OFTEN OCCUR HERE

CENTER ELECTRODE

[FILE FLAT WHEN

ADJUSTING GAP-

[DO NOT BEND!
(PROPER GAP)

(BEND TO ADJUST GAP)

CAUTION:

adjust gap.
Fig.
2 - Spark Plug Detail

Never bend the center electrode to

Always adjust by bending ground or

side electrode.

If available, test plugs with a spark plug tester.

Inspect spark plug hole threads and clean before in-

stalling plugs. Corrosion deposits can be removed

with a 14 mm. x 1.25 SAE spark plug tap (available

through local jobbers) or by using a small wire brush

in an electric drill. (Use grease on tap to catch

chips.)

ADJUST DWELL

ANGLE SETTING OR

POINT OPENING

Fig.
1 - Checking Compression
Fig.
3 - Distributor (In Line)

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE FUEL 6M-11

dripping fuel, but a leak on the suction would not be ap-

parent except for its effect of reducing volume of fuel on

the pressure side.

1.
Tighten any loose line connections and look for bends

or kinks in lines.

2.
Disconnect fuel pipe at carburetor. Disconnect dis-

tributor to coil primary wire so that engine can be

cranked without firing. Place suitable container at

end of pipe and crank engine a few revolutions. If

little or no gasoline flows from open end of pipe then

fuel pipe is clogged or pump is inoperative. Before

removing pump disconnect fuel pipe at gas tank and

outlet pipe and blow through them with an air hose

to make sure they are clear. Reconnect pipes and

retest while cranking engine.

CAUTION: Whenever the engine is cranked re-

motely at the starter, with a special jumper

cable or other means, the primary distributor

lead must be disconnected from the negative

post on the coil and the ignition switch must be

in the "ON" position. Failure to do this will

result in a damaged grounding circuit in the

ignition switch.

3.
If fuel flows from pump in good volume from pipe

at carburetor, check fuel delivery pressure to be

certain that pump is operating withint specified limits

as follows:

a. Attach a fuel pump pressure test gauge to dis-

connect end of pump to carburetor pipe.

b.
Run engine at approximately 450-1,000 rpm (on

gasoline in carburetor bowl) and note reading on

pressure gauge.

c. If pump is operating properly the pressure will

be within specifications and will remain constant

at speeds between 450-1,000 rpm. If pressure

is too low, too high, or varies materially at dif-

ferent speeds, the pump should be replaced.

Removal

1.
Disconnect fuel inlet and outlet pipes at fuel pump.
Fig.
2P-Installing 283, 327, 350 V8 Engine Fuel Pump

2.
Remove fuel pump mounting bolts and remove pump

and gasket.

3.
On V8 engines; if push rod is to be removed, remove

pipe plug then remove push rod (396 and 427 cu. in.

engines), remove fuel pump adapter and gasket then

remove push rod (283 and 327 cu. in. engines).

4.
If a new fuel pump is to be installed, transfer

fittings.

Installation

1.
On V8 engines; if removed, install fuel pump push

rod and pipe fitting or fuel pump adapter. Use.

gasket sealer on gasket or pipe fitting.

2.
Install fuel pump using a new gasket and tighten

securely. Use sealer on fuel pump mounting bolt

threads.

NOTE:
On V8 engines, a pair of mechanical

fingers may be used to hold fuel pump push rod

up while installing fuel pump (fig. 2P).

3.
Connect fuel pipes to pump.

4.
Start engine and check for leaks.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-11

I
BAT
JUNCTION BLOCK
DELCOTRON

—GRQ

BATTERY

&HJVVWV

0 VA OHM TEST RELAY >

RESISTOR [ 1 d

FUSIBLE

LINK

TO CRANKING

MOTOR
Ik

REGULATOR

VOLTMETER

FUSIBLE LINK

IGN.
SWITCH

Fig.
7c—Voltage Setting Test Connections

NOTE:
Voltage will not greatly exceed 12-1/2

volts until the battery develops a surface charge,

a few minutes generally, unless the battery is

severely discharged or is hot.

If reading is:

a. 12-1/2 volts or more, turn off electrical loads,

stop engine and proceed to Step 7.

b.
Less than 12-1/2 volts, perform "Delcotron Out-

put Test-Voltmeter Method."

(1) Delcotron tests bad—refer to "Service Op-

erations" and repair Delcotron, then repeat

Step 6.

(2) Delcotron tests good—disconnect regulator

connector, remove regulator cover and recon-

nect the connector. Then repeat Step 6 and

turn voltage adjusting screw (fig. 6c) to raise

setting to 12-1/2 volts. On transistor regula-

tor remove pipe plug (fig. 6c), insert screw

driver into slot and turn clockwise one or two

notches to increase setting. Turning counter-

clockwise decreases setting. For each notch

moved, the voltage setting will change ap-

proximately .3 volt. Turn off loads, stop en-

gine and proceed to Step 7. If 12-1/2 volts

cannot be obtained, install a new regulator and

repeat Step 6.

ADJUSTING REGULATOR VOLTAGE

7. Connect a 1/4 ohm-25 watt fixed resistor (purchased

commercially) into the charging circuit at the junc-

tion block as shown in Figure 7c.

NOTE:
Between both leads and the terminal.

8. Run engine at 1500 rpm or above for at least 15

minutes of warm-up, then cycle regulator voltage

control (by disconnecting and re-connecting regulator

connector) and read voltage.

If voltage is 13.5 to 15.2, the regulator is okay.

If voltage is not within 13.5 to 15.2 volts, leave en-

gine running at 1500 rpm or above and:
a. Disconnect four terminal connector and remove

regulator cover. Then re-connect four terminal

connector and adjust voltage to i4.2 to 14.6.

(Refer to Step 6 and fig. 6c).

b.
Disconnect four terminal connector and reinstall

regulator cover, then reinstall connector.

c. Continue running engine at 1500 rpm for 5-10

minutes to re-establish regulator internal

temperature.

d. Cycle regulator voltage by disconnecting and re-

connecting regulator connector. Read voltage. A

reading between 13.5 and 15.2 indicates a good

regulator.

CAUTION: Be sure four terminal regulator

connector is disconnected when removing or in-

stalling cover. This is to prevent regulator

damage by short circuits.

DELCOTRON OUTPUT TEST

Ammeter Method (Fig. 8c)

1.
Disconnect the battery ground cable at the battery.

2.
Disconnect the red wire at Delcotron battery termi-

nal and connect an ammeter in series between the

wire and terminal.

3.
Connect a voltmeter from battery terminal to a good

ground on the generator.

4.
Disconnect the F-R terminal connector at the

Delcotron.

5. Connect the jumper wire between Delcotron "F" and

battery terminals.

6. Connect the battery ground cable at the battery.

7. Connect an adjustable carbon pile across the battery

posts.

8. Start the engine and slowly bring the speed to 1500

RPM and at the same time adjust the carbon pile

load to hold the voltage at 14 volts.

9. Read the amperage and compare with a specifications

chart.

CHEVROLET CHASSIS SERVICE MANUAL