steering wheel CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

GENERAL INFORMATION 0-7

a vise using leather or wood on each side to prevent

damage to the cylinder,

7. Stake the retainer securely in place by staking the

cylinder metal over both edges of the retainer ends

using a suitable staking tool at right angles to the

top of the retainer and from the cast metal of the

cylinder over the retainer at each corner.

PUSHING, TOWING AND LIFTING

Pushing

NOTE:
Towing car to start is not recommended

due to the possibility of the disabled car ac-

celerating into tow car.

AUTOMATIC TRANSMISSION

Do not attempt to start the engine by pushing the car.

Should the battery become discharged, it will be neces-

sary to use an auxiliary battery with jumper cables to

start the engine.

CAUTION: To prevent damage to electrical

system, never connect booster batteries in ex-
cess of 12 volts and connect positive to positive

and negative to negative.

Manual Transmission

When a push start is necessary turn off all electrical

loads such as heater, radio, and if possible, lights, turn

on the key, depress the clutch, and place the shift lever

in high gear. Release the clutch when your speed reaches

10 to 15 miles per hour.

TOWING

The car may be towed safely on its rear wheels with

the (selector lever in "N" (Neutral) position at speeds

of 35 miles per hour or less under most conditions.

However, the drive shaft must be disconnected or the

car towed on its front wheels if 1) Tow speeds in excess

of 35 MPH are necessary, 2) Car must be towed for ex-

tended distances (over 50 miles) or, 3) Transmission is

not operating properly. If car is towed on its front

wheels, the steering wheel should be secured to maintain

a straight ahead position.

DRIVE ON HOIST

BUMPER JACK LIFTING AT FRAME ATTACHMENT ONLY

FLOOR JACK OR HOIST LIFT

Fig.
21-Vehicle Lifting Pointe-Chevroiet

CHEVROLET CHASSIS SERVICE MANUAL

GENERAL INFORMATION
0-9

Fig.
25—Attachment
of
Towing Chain Hooks
to
Axle Tube

Fig.
24—Towing Sling Attachment—Front

Rear

Connect standard chain hooks around the axle tube from

the underneath side between the axle rear spring pad and

the brake flange plate (fig. 25). It is mandatory that the

chain hook be positioned as stated above so that the brake

lines are not damaged.

The lower lifting bar should be positioned in below the

vehicle so that the rubber straps protect the rear valance

panel. With the lower bar in this position, it is necessary

that the bar be spaced down a minimum of
1
5/8" to pre-

vent damage to the fuel tank. This can be accomplished

by placing 6.0" section of 2x4' wood blocks below the

rear section of each rear spring (fig. 26).

To facilitate towing without a helper it will be neces-

sary to attach the
2x4*
s to the rear spring by a strap or

tape.
See Figure 27.

Also it will be necessary to lock the steering wheel in

the straight ahead position prior to actually moving the

vehicle.
Fig.
26—Towing SJing Attachment—Rear

REAR SPRING

EYE

WOOD

BLOCK

Fig.
27—Strapping Wood Block
to
Rear Spring

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-13

LUBRICATION

INDEX

Page

Engine Crankcase Oil . 0-13

Crankcase Capacities. . 0-13

Lubrication . ,
•
o-13

SAE Viscosity Oils 0-13

Types of Oils 0-14

Maintaining Oil Level 0-14

Oil and Filter Change Intervals 0-14

Oil.
. . ...:.. 0-14

Filter o-14

Crankcase Dilution . 0-14

Automatic Control Devices to Minimize

Crankcase Dilution 0-14

Crankcase Breather Cap 0-14

Crankcase Ventilation System 0-15

Valve Type 0-15

Fuel Filter 0-15

Air Cleaner . 0-15

Polyurethane Type 0-15

Oil Wetted Paper Element Type 0-15

Battery Terminal Washers 0-15
Page

Distributor 0-15

Rear Axle and 3-Speed and Overdrive

4-Speed Transmission 0-15

Recommended Lubricants 0-15

Multi-Purpose Gear Lubricants 0-15

Lubricant Additions 0-15

Lubricant Changes 0-15

Powerglide Transmission 0-15

Turbo Hydra-Matic 0-16

Front Wheel Bearings 0-16

Manual Steering Gear . . . . 0-16

Power Steering 0-16

Air Conditioning 0-16

Brake Master Cylinder. 0-16

Parking Brake 0-16

Clutch Cross-Shaft , 0-16

Chassis Lubrication 0-16

Lubrication Diagrams . . 0-19

Body Lubrication (Chevrolet, Chevelle, Chevy n, Camaro). 0-20

Body Lubrication Points (Corvette) . 0-21

The selection of the proper lubricant and its correct

application at regular intervals does much to increase the

life and operation of all moving parts of the vehicle.

Consequently, it is important that the correct grade of

oil or grease, as noted in the following pages, be used.

ENGINE CRANKCASE OIL

Crankcase Capacity

4 Cylinder 4 qt.

6 Cylinder 4 qt.

8 Cylinder (283) 4 qt.

8 Cylinder (327) 4 qt.

8 Cylinder (350) 4 qt.

8 Cylinder (396) 4 qt.

8 Cylinder (427) Chevrolet 4 qt.

8 Cylinder (427) Corvette 5 qt.

For 4 Cyl. Add .5 qt. with filter change;

1 qt. for 6 and 8 Cyl. engines.

Lubrication

Crankcase oil should be selected to give the best per-

formance under the climatic and driving conditions in the

territory in which the vehicle is driven.

During warm or hot weather, an oil which will provide

adequate lubrication under high operating temperatures

is required.

During the colder months of the year* an oil which will

permit easy starting at the lowest atmospheric tempera-

ture likely to be encountered, should be used.

When the crankcase is drained and refilled, the crank-

case oil should be selected, not on the basis of the exist-

ing temperature at the time of the change, but on the

lowest temperature anticipated for the period during

which the oil is to be used.

Unless the crankcase oil is selected on the basis of

viscosity or fluidity of the anticipated temperature, dif-

ficulty in starting will be experienced at each sudden

drop in temperature.
SAE Viscosity Oils

SAE Viscosity Numbers indicate only the viscosity or

body of the oil, that is, whether an oil is a light or a

heavy body oil, and do not consider or include other

properties or quality factors.

The lower SAE Viscosity Numbers, such as SAE 5W

and SAE 10W which represent the light body oils, are

recommended for use during cold weather to provide

easy starting and instant lubrication. The higher SAE

Viscosity Numbers such as SAE 20 and SAE 20W, which

represents heavier body oils, are recommended for use

during warm or hot weather to provide improved oil

economy and adequate lubrication under high operating

temperatures.

Oils are available which are designed to combine the

easy starting characteristics of the lower SAE Viscosity

Number with the warm weather operating characteristics

of the higher SAE Viscosity Number. These are termed

"multi-viscosity oils," SAE 5-10W, SAE 5W-20, SAE

10W-20W, and SAE 10W-30.

The following chart will serve as a guide for the

selection of the correct SAE Viscosity Number for use

under different atmospheric temperature ranges, and

suggests the appropriate SAE Viscosity Numbers when

multi-viscosity oils are used.

Lowest Anticipated

Temperature

During Time

Oil Will Be

in Crankcase

32°F.

0°F.

Below 0°F.
Recommended

SAE Viscosity

Oils

SAE 20 or 20W

SAE 10W

SAE 5W
Recommended

SAE

Multi-

Viscosity

Oils

SAE 10W-30 .

SAE 10W-30

SAE 5W-20

SAE 30 or 10W-30 is recommended when most of the

driving is at high speeds and/or at temperatures above

90
°F.

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-16

Every 12,000 miles (more frequently*, depending on

severity of service, if vehicle is used to pull trailers,

carry full loads during high ambient temperatures,

operate in mountainous terrain or operate under other

severe conditions--Remove fluid from the transmission

sump and add one and a half quarts of fresh fluid for

Camaro and Chevy II and two quarts for Chevrolet,

Chevelle, and Corvette. Operate transmission through all

ranges and check fluid level as described above.

•Except if vehicle is equipped with transmission pro-

vided in heavy duty service options. If so equipped,

drain converter and pump every 12,000 miles and add

approximately seven and a half quarts of fresh fluid

for Chevy II and nine quarts for Chevrolet and Chevelle.

TURBO HYDRA-MATIC

Lubrication. recommendations for the Turbo Hydra-

Matic are the same as outlined for the Powerglide

transmission except for fluid capacity and filter change

listed below.

After checking transmission fluid level it is important

that the dip stick be pushed all the way into the fill tube.

Every 12,000 miles — after removing fluid from the

transmission sump, approximately 7 1/2 pints of fresh

fluid will be required to return level to proper mark on

the dip stick.

Every 24,000 miles, or at every other fluid change--

the transmission sump strainer should be replaced.

FRONT WHEEL BEARINGS

It is necessary to remove the wheel and hub assembly

to lubricate the bearings. The bearing assemblies should

be cleaned before repacking with lubricant. Do not pack

the hub between the inner and outer bearing assemblies

or the hub caps, as this excessive lubrication results in

the lubricant working out into the brake drums and

linings.

Front wheels of all passenger car models are equipped

with tapered roller bearings and should be packed with a

high melting point water resistant front wheel bearing

lubricant whenever wheel and hub are removed.

CAUTION: "Long fibre" or "viscous" type

lubricant should not be used. Do not mix wheel

bearing lubricants. Be sure to thoroughly clean

bearings and hubs of all old lubricant before

repacking.

The proper adjustment of front wheel bearings is one

of the important service operations- that has a definite

bearing on safety. A car with improperly adjusted front

wheel bearings lacks steering stability, has a tendency to

wander or shimmy and may have increased tire wear.
The adjustment of these bearings is very critical. The

procedure is covered in Section 3 of this manual under

Front Wheel Bearings—Adjust,

MANUAL STEERING GEAR

Check lubricant level every 36,000 miles. If required,

add EP Chassis Lubricant.

POWER STEERING

On models equipped with power steering gear, check

fluid at operating temperature in pump reservoir. Add

GM Power Steering Fluid, or, if this is not available, use

Automatic Transmission Fluid "Type A" bearing the

mark AQ-ATF followed by a number and the suffix letter

'A'
to bring level to full mark on dip stick.

AIR CONDITIONING

After the first 6,000 miles, check all hose clamp

connections for proper tightness.

Every 6,000 miles check sight glass under the hood,

after the system has been in operation for several

minutes. Sight glass should be clear but may, during

milder weather, show traces of bubbles. Foam or dirt

indicate a leak which should be repaired immediately.

BRAKE MASTER CYLINDER

Check level every 6,000 miles and maintain 1/4" below

lowest edge of each filler opening with GM Hydraulic

Brake Fluid Supreme No. 11.

PARKING BRAKE

Every 6,000 miles, apply water resistant lube to park-

ing brake cable, cable guides and at all operating links

and levers.

CLUTCH CROSS-SHAFT

Periodic lubrication of the clutch cross shaft is not

required. At 36,000 miles or sooner, if necessary;

remove plug, install lube fitting and apply CHASSIS

LUBRICANT.

CHASSIS LUBRICATION

For chassis lubrication, consult the lubrication chart.

It shows the points to be lubricated and how often the

lubricant should be applied.

The term "chassis lubricant" as used in this manual,

describes a water resistant EP chassis grease designed

for application by commercial pressure gun equipment.

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-17

LUBRICATE EVERY 6,000 MILES

LUBRICATE EVERY 12,000 MILES

LUBRICATE EVERY 36,000 MILES

Refill Positraction Rear Axle with

Special Lubricant Only.
GL—Multi-purpose
or
Universal Gear Lubricant4

WB-Wheel Bearing Lubricant

(Whenever Brakes are serviced)

CL—Chassis Lubricant

EO-EngineOil
AT-Automatic Transmission Fluid {Type
A)

BF-Brake Fluid

Fig.
32—Lubrication Diagram—Chevrolet

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
4.
Air Cleaner

5. Crankcase Breather Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9. Oil Filter
10.
Battery

11.
Parking Brake

12.
Brake Master Cylinder

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-18

12

LUBRICATE EVERY 6000 MILES GL -Multi-purpose Gear Lubricant*

WB—Wheel Bearing Lubricant

LUBRICATE EVERY 12000 MILES (Whenever Brakes are serviced)

CL —Chassis Lubricant

LUBRICATE EVERY 36000 MILES E°-En9ine°il

"Refill Positraction Rear Axle with Special Positraction Rear Axle

Lubricant Only.
AT —Automatic Transmission Fluid (Type A)

SL —Steering Gear Lubricant

BF -Hydraulic Brake Fluid

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
Fig.
33—Lubrication Diagram—Chevelle

4.
Air Cleaner

5. Crankcase Breather Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9. Oil Filter
10.
Battery

11.
Parking Brake

12.
Brake Master CylincU

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION
0-19

.
3-SPEED
4-SPEED

7 OVER DRIVE

10 9 5 1 6 2 '
AUTOMATIC

3 12 11

LUBRICATE EVERY 6,000 MILES GL-Gear Lubricant*

WB-Wheel Bearing Lubricant

(Wh Bk
AT-Automdtic Transmission Fluid

^ WB-Wheel Bearing Lubricant (Type A)

-TV
LUBRICATE
EVERY 12,000 MILES (Whenever Brakes are serviced)

' CL—Chassis Lubricant

• LUBRICATE EVERY 36,000 MILES EO_Engine Oil
BF
-Brake Fluid

•Refill Positt

Special Lubricant Only.
Axl«
with

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
Fig.
34—Lubrication Diagram—Chevy I!

4. Air Cleaner

5. Crankcase Breather. Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9.
Oil Filter
10.
Battery

11.
Parking Brake

12.
Brake Master Cylinder

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-20

3-SPEED

4—SPEED

AUTOMATIC

LUBRICATE EVERY 6000 MILES

LUBRICATE EVERY 12000 MILES

LUBRICATE EVERY 36000 MILES

*
Refill
positraction rear axle with

special lubricant only.
GL -GEAR LUBRICANT*

WB-WHEEL BEARING LUBRICANT

(WHENEVER BRAKES
ARE
SERVICED)

CL -CHASSIS LUBRICANT

CO-ENGINE
Oil;
AT -AUTOMATIC TRANSMISSION

FLUID (TYPE
A)

BF -BRAKE FLUID

Fig.
35—Lubricafion Diagram—Camaro

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
4.
Air Cleaner

5. Crankcase Breathe Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9. Oil Filter
10.
Battery,

11.
Parking Brake

12.
Brake Master Cylinder

BODY LUBRICATION

See Body Service Manual
for
Body Lubrication,

cept Corvette)
(Ex-

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION
0-21

6

3-SPEED

4-SPEED

AUTOMATIC

10

LUBRICATE EVERY 6,000 MILES GL -Multi-purpose
or
Universal Gear Lubrincant*

-(V LUBRICATE EVERY 12,000 MILES WB-Wheel Bearing Lubricant

V/^ (Whenever Brakes
are
serviced)
AT —Automatic Transmission Fluid (Type)

BF -Brake Fluid

a
LUBRICATE EVERY 36,000 MILES

* Refill Positraction Rear Axle with

Special Lubricant Only.
CL -Chassis Lubricant

EO—Engine
Oil

Fig.
36—Lubrication Diagram—Corvette

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
4.
Air
Cleaner

5. Front Wheel

Bearings
6. Transmission

7. Rear Axle

8.
Oil
Filter
9. Battery

10.
Parking Brake

11.
Brake Master Cylinder

BODY LUBRICATION POINTS (CORVETTE)

Lubricate the following items when possible.

Hood Latch Mechanism and Hinges --Apply light engine oil

to pivot points. Don't oil lock pins or catch plates.

i

Rear Compartment Lid Release and Hinges --Apply light

engine
oil.

Side Door Hinge Pins—Apply light engine oil.
Door Lock Rotor and Striker Plate—Apply light engine oil or

stainless stick lubricant.

Lock Cylinders—Lubricate with powdered graphite.

Window Regulators and Controls and Door Lock Remote

Link —Apply light engine
oil.

Gas Tank Filler Cap Hinge—Apply light engine oil.

Weatherstrips and Rubber Bumpers —Coat lightly with
a

rubber lubricant.

CHEVROLET CHASSIS SERVICE MANUAL

SECTION 2

FRAME

INDEX

Page

General Description 2-1

Chevrolet 2-1

Cheveile '. 2-1

Repair Procedures 2-1
Page

Checking Frame Alignment 2-1

Car Preparation 2-1

Tramming Sequence 2-1

Reference Point Dimensions 2-1

GENERAL DESCRIPTION

CHEVROLET AND CHEVELLE

Frames used on Chevrolet and Cheveile lines are basi-

cally the same, consisting of full length right and left

side members joined laterally by crossmembers. Sev-

eral different frames are used in each line to meet the

various vehicle size and function requirements but the

basic shape for each line remains the same. Differences

between frames in a given line exist only in metal gauge,

part size and numbers of parts necessary to meet the

particular structural requirements of the models

involved.

CORVETTE

The Corvette frame is a rigid perimeter unit, with five
crossmembers. From the rear kick-up forward, trap-

azoidal shaped, closed side members outline and protect

the passenger compartment. At the cowl area, the side

members curve inward in a sweeping "S" shape, to pro-

vide a sturdy foundation for the engine mounts and clear-

ance for front wheel movement. From the kick-up

rearward, box-sectioned side rails provide fore and aft

support for the rear axle and suspension. Lateral sup-

port is provided by five variously shaped welded-in

crossmembers, including the front unit, which formerly

was bolted-in.

CHEVY II AND CAMARO

Underbody alignment checking procedures will be found

in the Body Service Manual.

REPAIR PROCEDURES

CHECKING FRAME ALIGNMENT

Vehicles involved in an accident of any nature which

might result in a "swayed" or "sprung" frame should

always be checked for proper frame alingment in addi-

tion to steering geometry and wheel alignment.

CAR PREPARATION

Preparing the car for the frame alignment check in-

volves the following:

1.
Place the car on level surface.

2.
The weight of the car should be supported at the

wheel locations.

3.
A visual damage inspection should be made to elim-

inate needless measuring. Obviously damaged or

misaligned areas can often be located by sight.

TRAMMING SEQUENCE

When checking a frame for alignment in case of dam-

age,
the first step is horizontal "X" checking with a

tram from similar given points on opposite side of the

frame.

Frame alignment checks on all models should be made

with the tram points set at the center of each locating

point indicated and the cross bar level to insure

accuracy.

When "X" checking any section of the frame, the

measurements should agree within 3/16". If they do not,
it means that corrections will have to be made.

If a tram gauge is not available, the "plumb bob"

method of checking may be used. To assure any degree

of accuracy when using this method, the vehicle should

be on a level floor.

By using this method, it is only necessary to have a
#

piece of cord attached to an ordinary surveyor's plumb

bob.
When measuring the distance between two points,

the free end of the cord should be placed on the reference

point allowing the plumb bob to hang on the floor. A check

mark should be made on the floor just under the tip of

the plumb bob. This operation should be repeated at all

reference points. With these points located on the floor,

they may easily be measured with a rule.

The second step is checking the vertical dimensions

from the datum plane to the points to be trammed. With

the proper settings the tram bar will be on a plane

parallel to that of the frame. The exception to this would '

be when one of the reference locations is included in the

misaligned area; then the parallel plane between the

frame and the tram bar may not prevail. After com-

pletion of the repairs, the tram gauge should be set at

the specified dimension to check the accuracy of the re-

pair operation.

ALIGNMENT REFERENCE POINT DIMENSIONS

Dimensions to holes are measured to dead center of

the holes and flush to the adjacent surface metal.

CHEVROLET CHASSIS SERVICE MANUAL