brake CHEVROLET CORVETTE 2007 6.G Owners Manual

To program each button, use the following steps:
1. Adjust the settings for the driver’s seat
position, both outside mirrors, and the
telescopic steering column position to a
comfortable driving position.
2. Press and hold button 1 until two beeps are
heard, then release the button.
Your settings are now programmed.
A second seating, mirror, and telescopic steering
column position can be programmed by
repeating the above steps and pressing button 2
for driver 2.
To recall a memory position, do one of the
following:
If you have an automatic transmission vehicle,
press and release the desired button 1 or 2
while the vehicle is in PARK (P).
A single beep will sound and the memory
position will be recalled after a brief delay.
If the vehicle is not in PARK (P), three beeps
will sound and the memory position will
not be recalled.
If you have a manual transmission vehicle,
press and release the desired button 1 or 2.
If the vehicle is on, the parking brake needs to
be set to recall the memory position.
A single beep will sound and the memory
position will be recalled after a brief delay.
If the vehicle is on and the parking brake is not
set, three beeps will sound and the memory
position will not be recalled.
If your vehicle has the Auto Memory Recall
feature and it is turned on in the Driver Information
Center (DIC), the seat, mirrors, and telescopic
steering column position will automatically adjust
to their programmed positions when the engine
is started. See “Auto Memory Recall” under
DIC Vehicle Personalization on page 234for more
information.
To stop recall movement of the memory feature at
any time, press one of the power seat controls,
power mirror control buttons, memory buttons, or
the telescopic steering column switch.
11

Easy Exit Seat
Two personalized exit positions can also be
programmed to allow for an easy exit or entry into
the vehicle. The controls for this memory
function are located on the driver’s door.
B(Easy Exit Seat):This button is used to
program and recall the desired driver’s seat exit
position.
To program an exit position, use the
following steps:
1. Recall the desired driving position by pressing
button 1 or 2.
The seat will move to the programmed
memory position.
2. Position the seat and the telescopic steering
column position to a comfortable exit position.
3. Press and hold the exit button until two beeps
sound.
Your exit position is now programmed.A second exit position can be programmed by
repeating the above steps and pressing the other
memory button.
To recall an exit position, do one of the following:
If you have an automatic transmission
vehicle, press and release the exit button while
the vehicle is in PARK (P).
One beep will sound and the exit position for
the currently identied driver will be recalled.
If you have a manual transmission vehicle,
press and release the exit button. The
parking brake needs to be set to recall the
memory position.
One beep will sound and the exit position for
the currently identied driver will be recalled.
If your vehicle has the Auto Exit Recall feature
and it is turned on in the DIC, automatic seat and
telescopic steering column movement to the
exit position will occur when you use the keyless
access transmitter to unlock your vehicle or
when you turn the engine off and open the driver’s
door. See “Auto Exit Recall” underDIC Vehicle
Personalization on page 234for more information.
12

Keys.............................................................. 71
Keyless Access System.............................. 72
Keyless Access System Operation.............. 73
Doors and Locks.......................................... 78
Door Locks................................................. 78
Power Door Locks....................................... 80
Automatic Door Lock................................... 81
Programmable Automatic Door Unlock........ 81
Lockout Protection....................................... 82
Hatch/Trunk................................................. 82
Windows....................................................... 85
Power Windows.......................................... 86
Sun Visors.................................................. 87
Theft-Deterrent Systems............................... 87
Theft-Deterrent System................................ 87Starting and Operating Your Vehicle........... 89
New Vehicle Break-In.................................. 89
Ignition Positions......................................... 90
Retained Accessory Power (RAP)............... 91
Starting the Engine..................................... 91
Engine Coolant Heater................................ 93
Automatic Transmission Operation............... 95
Manual Transmission Operation................. 100
Parking Brake........................................... 102
Shifting Into Park (P)
(Automatic Transmission)....................... 103
Shifting Out of Park (P)
(Automatic Transmission)....................... 104
Parking Your Vehicle
(Manual Transmission)........................... 105
Parking Over Things That Burn................. 105
Engine Exhaust......................................... 106
Running the Engine While Parked............. 107
Section 2 Features and Controls
69

K(Unlock):Press this button to unlock the
driver’s door. The light on the door will ash
two times. Press the button two times within
10 seconds to unlock both doors. If it is dark
enough outside, your interior lamps will come on.
Your memory settings may also be recalled
when you press the unlock button on the keyless
access transmitter. SeeMemory Seat, Mirrors
and Steering Wheel on page 10for more
information.
}(Hatch/Trunk):Press and hold this button
for about one second to open the hatch/trunk
lid while the engine is turned off. If the engine is
running the shift lever needs to be in PARK (P)
for an automatic transmission or NEUTRAL
with the parking brake set for a manual
transmission. SeeParking Brake on page 102.
L(Panic):Press this button to sound the vehicle
alarm. Press any other button on the keyless
access transmitter to stop the vehicle alarm.
Matching Transmitter(s) to Your
Vehicle
Each keyless access transmitter is coded to allow
only transmitters programmed to your vehicle, to
work. If a transmitter is lost or stolen, a replacement
can be purchased and programmed through your
dealer/retailer. Your dealer/retailer can reprogram
your vehicle so lost or stolen transmitters no longer
work with your vehicle. Each vehicle can have a
maximum of four transmitters matched to it.
To match a new transmitter to your vehicle
when you have a recognized transmitter
(two recognized transmitters are required
for Canadian owners), do the following:
1. The vehicle must be off.
2. Have the recognized and new, unrecognized
transmitters on your person.
3. Go to the rear of the vehicle and insert the
vehicle key into the key cylinder located
above the license plate. SeeHatch/Trunk
on page 82for more information on the key
cylinder.
4. Open the trunk.
5. Turn the key ve times within ve seconds.
74

Battery Replacement
Under normal use, the battery in your keyless
access transmitter should last about three years.
The battery is weak if the transmitter will not
work at the normal range in any location. If you
have to get close to your vehicle before the
transmitter works, it is probably time to change
the battery.
A weak battery may also cause the DIC to display
NO FOBS DETECTED when you try to start the
vehicle. If this happens, place the transmitter in
the glove box transmitter pocket with the buttons
facing towards the passenger’s side. Then, with the
vehicle in PARK (P) for an automatic transmission,
press the brake pedal and the START button. If
your vehicle has a manual transmission, press
the clutch and the START button. Although this
will start the vehicle, it is recommended that you
replace the transmitter battery as soon as possible.
The DIC may display FOB BATTERY LOW.
Notice:When replacing the battery, use
care not to touch any of the circuitry. Static
from your body transferred to these surfaces
may damage the transmitter.1. Insert a at object with a thin edge into the
slot on the side or back of the transmitter
and separate the bottom half from the top half.
2. Gently pull the battery out of the transmitter.
3. Put the new battery in the transmitter,
positive (+) side down. Use a battery,
type CR2032, or equivalent.
4. Reassemble the transmitter. Make sure to put
it together so water will not get in.
5. Test the transmitter.
77

When lock is pressed, a beep will sound. If the
door is closed when lock is pressed, the light will
come on for a few seconds, then turn off. If
the door is open when lock is pressed, the light
will stay on.
When unlock is pressed, a beep will sound.
If the door is closed when unlock is pressed,
the light will ash two times. If the door is open
when unlock is pressed, the light will ash.
Automatic Door Lock
Your vehicle is programmed so that, when the
doors are closed, the ignition is on and the shift
lever is moved out of PARK (P) for automatic
transmissions, or when vehicle speed becomes
faster than 8 mph (13 km/h) for manual
transmissions, both doors will lock.
If someone needs to get out while the vehicle
is running or not in PARK (P), have the person use
the power door unlock switch. When the door is
closed again, the doors will lock either when your
foot is removed from the brake or the vehicle speed
becomes faster than 8 mph (13 km/h).
Programmable Automatic Door
Unlock
Your vehicle is programmed so that when the
shift lever is moved into PARK (P) for automatic
transmission vehicles or when the ignition is turned
off or is in Retained Accessory Power (RAP) for
manual transmission vehicles, both doors will
unlock.
With the vehicle stopped and the engine running,
door unlocking can be programmed through
prompts displayed on the Driver Information
Center (DIC). These prompts allow the driver to
choose various unlock settings. For programming
information, seeDIC Vehicle Personalization
on page 234.
81

Notice:Closing the hatch/trunk lid forcefully
or from the sides can cause damage to the
glass, the defogger or the weather stripping.
Be sure objects will t in the hatch/trunk
area before closing the hatch/trunk lid. When
closing the hatch/trunk lid, gently pull down
from the center.
Notice:Do not store heavy or sharp objects
in the rear storage compartments located in the
hatch/trunk area. If you do, the objects could
damage the underbody.
Hatch/Trunk Lid Release
There are several ways to release the hatch/trunk
lid. If your vehicle has an automatic transmission,
the shift lever must be in PARK (P). For manual
transmission vehicles, the parking brake must be
set when the ignition is started for the hatch/trunkrelease to operate. The parking brake does not
need to be set when the ignition is off for the
hatch/trunk release to operate. SeeParking
Brake on page 102.
V(Hatch/Trunk):Press the hatch/trunk lid
release button, located on the instrument
panel to the left of the steering wheel. The
theft-deterrent alarm system must not be
armed.
}(Hatch/Trunk):Press the hatch/trunk
lid release button on the keyless access
transmitter. SeeKeyless Access System
on page 72.
Press the hatch/trunk release button located on
the rear of the hatch/trunk lid above the license
plate, as long as you have your transmitter
with you.
83

Disarming the System
Always use your keyless access transmitter to
unlock a door either by pressing the unlock button
on the transmitter or by squeezing the door handle
sensor while you have the transmitter with you.
Unlocking a door any other way will set off the
alarm. If your alarm sounds, press the unlock
button on the keyless access transmitter to
disarm it.
Do not leave the key or device that disarms or
deactivates the theft deterrent system in the
vehicle.
Starting and Operating Your
Vehicle
New Vehicle Break-In
Notice:Your vehicle does not need an
elaborate break-in. But it will perform better in
the long run if you follow these guidelines:
Keep your speed at 55 mph (88 km/h)
or less for the rst 500 miles (805 km).
Do not drive at any one constant speed, fast
or slow, for the rst 500 miles (805 km).
Do not make full-throttle starts. Avoid
downshifting to brake, or slow, the vehicle.
Avoid making hard stops for the rst
200 miles (322 km) or so. During this time
the new brake linings are not yet broken in.
Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking-in guideline every
time you get new brake linings.
Following break-in, engine speed and load can
be gradually increased.
89

Ignition Positions
Your vehicle has an
electronic keyless
ignition with a
pushbutton start.
/(START):Press this button while your foot is on
the brake for an automatic transmission, or while
pressing in the clutch for a manual transmission,
to start the engine. If your vehicle is in OFF or
Retained Accessory Power (RAP) mode, the
keyless access transmitter must be inside the
vehicle to start the engine.
9Acc. (OFF/ACCESSORY):When the engine
is on or the vehicle is in accessory power mode,
it is recommended that a manual transmission beplaced in REVERSE (R). An automatic
transmission must be placed in PARK (P).
Then press the Acc. button to turn the engine
off and place the vehicle in RAP. See “Retained
Accessory Power (RAP)” later for more information.
If an automatic vehicle is not correctly placed in
PARK (P) a SHIFT TO PARK message will display
on the Driver Information Center (DIC).
For more information, seeDIC Warnings and
Messages on page 214.
When the engine is off, press this button to place
the vehicle in accessory mode. ACCESSORY
MODE ON will display on the Driver Information
Center (DIC). This mode allows you to use things
like the radio and the windshield wipers while the
engine is off. Use accessory mode if you must have
your vehicle in motion while the engine is off, for
example, if your vehicle is being pushed or towed.
After being in accessory mode for about
20 minutes, the vehicle will automatically enter
RAP or OFF, depending on if the doors are
opened or closed.
90

Retained Accessory Power (RAP)
These vehicle accessories can be used for up to
10 minutes after the engine is turned off:
Audio System
Power Windows
These features continue to work up to 10 minutes
after the engine is turned off or until either door
is opened. If a door is opened, the power windows
and audio system will shut off.
Starting the Engine
Move the shift lever to PARK (P) or NEUTRAL (N)
for an automatic transmission. For a manual
transmission the vehicle can be started in
NEUTRAL or any other gear as long as the clutch is
depressed. To restart a manual transmission when
you are already moving, use the NEUTRAL position
only. To restart an automatic transmission when
you are already moving, use NEUTRAL (N).Notice:Do not try to shift to PARK (P) if
your vehicle is moving. If you do, you could
damage the transmission. Shift to PARK (P)
only when your vehicle is stopped.
The keyless access transmitter must be inside the
vehicle for the ignition to work.
Cell phone chargers can interfere with the
operation of the Keyless Access System. Battery
chargers should not be plugged in when starting
or turning off the engine.
To start your vehicle, do the following:
1. For an automatic transmission, with your foot
on the brake pedal, press the START button
located on the instrument panel. For a manual
transmission, while pressing in the clutch,
press the START button.
If there is not a keyless access transmitter in
the vehicle or if there is something causing
interference with it, the DIC will display
NO FOBS DETECTED. SeeDIC Warnings
and Messages on page 214for more
information.
91