CHRYSLER 200 2017 2.G Owners Manual

Do Not Disturb
With Do Not Disturb, you can disable notifications from
incoming calls and texts, allowing you to keep your eyes
on the road and hands on the wheel. For your convenience,
there is a counter display to keep track of your missed calls
and text messages while you were using Do Not Disturb.Do Not Disturb can automatically reply with a text mes-
sage, a call or both, when declining an incoming call and
send it to voicemail.
Automatic reply messages can be:
•
“I am driving right now, I will get back to you shortly.”
• Create a custom auto reply message up to 160 characters.
NOTE: Only the first 25 characters can been seen on the
touchscreen while typing a custom message.
While in Do Not Disturb, Conference Call can be selected
so you can still place a second call without being inter-
rupted by incoming calls.
NOTE:
• Reply with text message is not compatible with iPhones.
• Auto reply with text message is only available on
phones that supporting Bluetooth MAP.
Siri Eyes Free
4
UNDERSTANDING YOUR INSTRUMENT PANEL 339

General Information
This device complies with FCC rules Part 15 and Industry
Canada RSS-210. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may bereceived including interference that may cause unde-
sired operation.
NOTE:
• The transmitter has been tested and it complies with
FCC and IC rules. Changes or modifications not ex-
pressly approved by the party responsible for compli-
ance could void the user ’s authority to operate the
device.
• The term IC before the certification/registration number
only signifies that Industry Canada technical specifica-
tions were met.
Additional Information
© 2016 FCA US LLC. All rights reserved. Mopar and
Uconnect are registered trademarks and Mopar Owner
Connect is a trademark of FCA US LLC. Android is a
trademark of Google Inc. SiriusXM and all related marks
and logos are trademarks of SiriusXM Radio Inc. Yelp, Yelp
logo, Yelp burst and related marks are registered trade-
marks of Yelp.
For Uconnect system support, call: 1-877-855-8400
(24 hours a day 7 days a week) or visit DriveUconnect.com.
Uconnect Access services support, call: 1-855-792-4241
Please have your Uconnect Security PIN ready when you
call.
340 UNDERSTANDING YOUR INSTRUMENT PANEL

STARTING AND OPERATING
CONTENTS
STARTING PROCEDURES .................344
▫ Normal Starting — Gasoline Engine .........344
▫ Extreme Cold Weather (Below –22°F Or 30°C) .344
▫ Extended Park Starting ...................345
▫ If Engine Fails To Start ..................345
▫ After Starting ......................... .346
 ENGINE BLOCK HEATER — IF EQUIPPED . . . .346
 AUTOMATIC TRANSMISSION ..............347
▫ Ignition Park Interlock ...................348
▫ Brake/Transmission Shift Interlock System . . . .348
▫ Nine-Speed Automatic Transmission .........348
▫ Gear Ranges ......................... .350
 PADDLE SHIFT MODE — IF EQUIPPED .......354
▫ Operation ........................... .354
ALL WHEEL DRIVE (AWD) — IF EQUIPPED . . .356
 DRIVING ON SLIPPERY SURFACES ..........356
▫ Acceleration .......................... .356
▫ Traction ............................ .357
 DRIVING THROUGH WATER ..............357
▫ Flowing/Rising Water ...................357
▫ Shallow Standing Water ..................357
 POWER STEERING ...................... .358
 ELECTRIC PARK BRAKE (EPB) .............359
▫ Auto Park Brake ...................... .362
▫ SafeHold ............................ .362
▫ Brake Service Mode .....................363
 BRAKE SYSTEM ....................... .364
 ELECTRONIC

BRAKE CONTROL SYSTEM .....364
5

▫Electronic Brake Force Distribution (EBD) ......364
▫ Brake System Warning Light ...............364
▫ Anti-Lock Brake System (ABS) .............365
▫ Anti-Lock Brake Warning Light .............366
▫ Brake Assist System (BAS) ................366
▫ Hill Start Assist (HSA) ...................367
▫ Traction Control System (TCS) .............369
▫ Electronic Stability Control (ESC) ...........369
▫ Electronic Roll Mitigation (ERM) ............372
▫ Ready Alert Braking (RAB) ................373
▫ Rain Brake Support (RBS) .................373
▫ Dynamic Steering Torque (DST) .............373
 TIRE SAFETY INFORMATION ..............374
▫ Tire Markings ........................ .374
▫ Tire Identification Number (TIN) ............376
▫ Tire Terminology And Definitions ...........378
▫ Tire Loading And Tire Pressure ............379
TIRES — GENERAL INFORMATION .........382
▫ Tire Pressure ......................... .382
▫ Tire Inflation Pressures ..................384
▫ Tire Pressures For High Speed Operation .....384
▫ Radial Ply Tires ....................... .385
▫ Tire Types ........................... .385
▫ Run Flat Tires — If Equipped ..............387
▫ Spare Tires — If Equipped ................387
▫ Tire Spinning ........................ .390
▫ T

read Wear Indicators ...................390
▫ Life Of Tire .......................... .391
▫ Replacement Tires ..................... .391
 TIRE CHAINS (TRACTION DEVICES) .........392
 TIRE ROTATION RECOMMENDATIONS ......393
 TIRE PRESSURE MONITOR SYSTEM (TPMS) . . .394
▫ Premium System — If Equipped ............396
▫ General Information .....................399
342 STARTING AND OPERATING

FUEL REQUIREMENTS ...................400
▫ Reformulated Gasoline ..................400
▫ Gasoline/Oxygenate Blends ...............400
▫ E-85 Usage In Non-Flex Fuel Vehicles .........401
▫ MMT In Gasoline ...................... .401
▫ Materials Added To Fuel .................402
▫ Fuel System Cautions ....................402
▫ Carbon Monoxide Warnings ...............403
 FLEXIBLE FUEL — IF EQUIPPED ............403
▫ E-85 General Information .................403
▫ Ethanol Fuel (E-85) ..................... .403
▫ Fuel Requirements .....................404
▫ Selection Of Engine Oil For Flexible Fuel Vehicles
(E-85) And Gasoline Vehicles ..............404
▫ Starting ............................ .405▫
Cruising Range ....................... .405
▫ Replacement Parts ..................... .405
▫ Maintenance ......................... .405
 ADDING FUEL ........................ .406
▫ Loose Fuel Filler Cap Message .............408
 VEHICLE LOADING .....................409
▫ Certification Label ..................... .409
 TRAILER TOWING ..................... .410
 RECREATIONAL TOWING (BEHIND
MOTORHOME, ETC.) ....................411
▫ Towing This Vehicle Behind Another Vehicle . . . .411
▫ Recreational Towing — Front-Wheel Drive (FWD)
Models ..............................411
▫ Recreational Towing — All-Wheel Drive (AWD)
Models ............................. .412
5
STARTING AND OPERATING 343

STARTING PROCEDURES
Before starting your vehicle, adjust your seat, adjust both
inside and outside mirrors, and fasten your seat belts.
WARNING!
•When leaving the vehicle, always remove the key fob
from the ignition and lock your vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle.
• Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or others
could be seriously or fatally injured. Children
should be warned not to touch the parking brake,
brake pedal or the gear selector.
• Do not leave the key fob in or near the vehicle, or in
a location accessible to children, and do not leave the
ignition of a vehicle equipped with Keyless Enter-
N-Go in the ACC or ON/RUN mode. A child could
operate power windows, other controls, or move the
vehicle.
Start the engine with the gear selector in the NEUTRAL or
PARK position. Apply the brake before shifting to any
driving range.
Normal Starting — Gasoline Engine
NOTE: Normal starting of either a cold or a warm engine
is obtained without pumping or pressing the accelerator
pedal.
Cycle the ignition switch to the START position and release
when the engine starts. If the engine fails to start within 10
seconds, cycle the ignition switch to the LOCK/OFF posi-
tion, wait 10 to 15 seconds, then repeat the “Normal
Starting” procedure.
Tip Start Feature
Cycle the ignition switch to START position and release it.
The starter motor will continue to run, and will automati-
cally disengage itself when the engine is running. If the
engine fails to start, the starter will disengage automati-
cally in 10 seconds. If this occurs, cycle the ignition switch
to the OFF position, wait 10 to 15 seconds, then repeat the
“Normal Starting” procedure.
Extreme Cold Weather (Below –22°F Or 30°C)
To ensure reliable starting at these temperatures, use of an
externally powered electric engine block heater (available
from your authorized dealer) is recommended.
344 STARTING AND OPERATING

Extended Park Starting
NOTE:Extended Park condition occurs when the vehicle
has not been started or driven for at least 30 days.
1. Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.
2. Cycle the ignition in the START position and release it when the engine starts.
3. If the engine fails to start within 10 to 15 seconds, cycle the ignition to the STOP (OFF/LOCK) position, wait
five seconds to allow the starter to cool, then repeat the
Extended Park Starting procedure.
4. If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the
procedure.
CAUTION!
To prevent damage to the starter, do not crank continu-
ously for more than 10 seconds at a time. Wait 10 to 15
seconds before trying again.
If Engine Fails To Start
WARNING!
•Never pour fuel or other flammable liquid into the
throttle body air inlet opening in an attempt to start
the vehicle. This could result in flash fire causing
serious personal injury.
• Do not attempt to push or tow your vehicle to get it
started. Vehicles equipped with an automatic trans-
mission cannot be started this way. Unburned fuel
could enter the catalytic converter and once the
engine has started, ignite and damage the converter
and vehicle.
• If the vehicle has a discharged battery, booster cables
may be used to obtain a start from a booster battery
or the battery in another vehicle. This type of start
can be dangerous if done improperly. Refer to
“Jump-Starting” in “What To Do In Emergencies” for
further information.
With Tip Start
If the engine fails to start after you have followed the
Normal Starting, “Extreme Cold Weather andExtended
5
STARTING AND OPERATING 345

Park Startingprocedures; it may be flooded. To clear any
excess fuel;
1. Press the accelerator pedal all the way to the floor and hold it
2. Cycle the ignition to the START position and release it as soon as the starter engages. The starter motor will
disengage automatically in 10 seconds.
3. Once this occurs, release the accelerator pedal.
4. Cycle the ignition to the LOCK position, wait 10 to 15 seconds, then repeat the “Normal Starting” procedure.
CAUTION!
To prevent damage to the starter, wait 10 to 15 seconds
before trying again.
After Starting
The idle speed is controlled automatically, and it will
decrease as the engine warms up.
ENGINE BLOCK HEATER — IF EQUIPPED
The engine block heater warms the engine and permits
quicker starts in cold weather. Connect the cord to a 110-115 Volt AC electrical outlet with
a grounded, three-wire extension cord.
For ambient temperatures below 0°F (-18°C), the engine
block heater is recommended. For ambient temperatures
below -20°F (-29°C), the engine block heater is required.
The engine block heater cord is routed under the hood,
behind to the driver ’s side headlamp. Follow the steps
below to properly use the engine block heater:
1. Locate the engine block heater cord (behind the driver ’s
side headlamp).
2. Undo the Velcro strap that secures the heater cord in place.
3. Pull the cord to the front of the vehicle and plug it into a grounded, three-wire extension cord.
4. After the vehicle is running, reattach the cord to the Velcro strap and properly stow away behind the driver ’s
side headlamp.
NOTE:
• The engine block heater cord is a factory installed
option. If your vehicle is not equipped, heater cords are
available from your authorized MOPAR dealer.
346 STARTING AND OPERATING

•The engine block heater will require 110 Volts AC and 6.5
Amps to activate the heater element.
• The engine block heater must be plugged in at least one
hour to have an adequate warming effect on the engine.
WARNING!
Remember to disconnect the engine block heater cord
before driving. Damage to the 110-115 Volt electrical
cord could cause electrocution.
AUTOMATIC TRANSMISSION
CAUTION!
Damage to the transmission may occur if the following
precautions are not observed:
• Shift into or out of PARK or REVERSE only after the
vehicle has come to a complete stop.
• Do not shift between PARK, REVERSE, NEUTRAL,
or DRIVE when the engine is above idle speed.
• Before shifting into any gear, make sure your foot is
firmly pressing the brake pedal.
WARNING!
• It is dangerous to shift out of PARK or NEUTRAL if
the engine speed is higher than idle speed. If your
foot is not firmly pressing the brake pedal, the
vehicle could accelerate quickly forward or in re-
verse. You could lose control of the vehicle and hit
someone or something. Only shift into gear when the
engine is idling normally and your foot is firmly
pressing the brake pedal.
• Unintended movement of a vehicle could injure
those in or near the vehicle. As with all vehicles, you
should never exit a vehicle while the engine is
running. Before exiting a vehicle, always apply the
parking brake, shift the transmission into PARK, and
turn the ignition OFF. When the ignition is in the
OFF mode, the transmission is locked in PARK,
securing the vehicle against unwanted movement.
• When leaving the vehicle, always make sure the
ignition is in the OFF mode, remove the key fob from
the vehicle, and lock the vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Allowing children to
be in a vehicle unattended is dangerous for a number
(Continued)
5
STARTING AND OPERATING 347

WARNING!(Continued)
of reasons. A child or others could be seriously or
fatally injured. Children should be warned not to
touch the parking brake, brake pedal or the trans-
mission gear selector.
• Do not leave the key fob in or near the vehicle (or in
a location accessible to children), and do not leave
the ignition in the ACC or ON/RUN mode. A child
could operate power windows, other controls, or
move the vehicle.
NOTE: You must press and hold the brake pedal while
shifting out of PARK.
Ignition Park Interlock
This vehicle is equipped with an Ignition Park Interlock
which requires the transmission to be in PARK before the
ignition can be turned off. This helps the driver avoid
inadvertently leaving the vehicle without placing the trans-
mission in PARK. This system also locks the transmission
in PARK whenever the ignition is in the OFF mode.
Brake/Transmission Shift Interlock System
This vehicle is equipped with a Brake Transmission Shift
Interlock system (BTSI) that holds the transmission gear selector in PARK unless the brakes are applied. To shift the
transmission out of PARK, the engine must be running and
the brake pedal must be pressed. The brake pedal must
also be pressed to shift from NEUTRAL into DRIVE or
REVERSE when the vehicle is stopped or moving at low
speeds.
Nine-Speed Automatic Transmission
The transmission is controlled using a rotary electronic
gear selector located on the center console. The transmis-
sion gear range (PRNDL/S) is displayed above the gear
selector. To select a gear range, simply rotate the gear
selector. Push down on the gear selector and then rotate it,
to access the L or S position. You must also press the brake
pedal to shift the transmission out of PARK, or to shift from
NEUTRAL into DRIVE or REVERSE when the vehicle is
stopped or moving at low speeds (refer to
Brake/
Transmission Shift Interlock System in this section). To
shift past multiple gear ranges at once (such as PARK to
DRIVE), simply rotate the gear selector to the appropriate
detent. Select the DRIVE range for normal driving.
The electronically-controlled transmission provides a pre-
cise shift schedule. The transmission electronics are self-
calibrating; therefore, the first few shifts on a new vehicle
348 STARTING AND OPERATING