air conditioning Citroen BERLINGO 2004 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 126
ENGINE
B1BP1HJC
XSARAAUXILIARY EQUIPMENT DRIVE BELT 2002
Fit the drive belt.
The tensioner roller
(1).
Tighten the screws
(3)to 2 m.daN.
Move the tensioner roller
(1)using the tool (9.52 mm square drive (3/8))at (2), in order to remove
the tool or locking peg
(Ø 4 mm)at (4).
Slowly release the tensioner roller
(1)so that the roller (5)presses against the belt.
With air conditioning. Engine: RFS

Downloaded from www.Manualslib.com manuals search engine 127
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT 2002XSARA
Tools.
[1]
Belt tension measuring instrument :4122T
(1)
Tensioning screw.
(2)Roller support fixing screw (3).
Lightly tighten the screws
(2).
Place the tool
[1]on the belt.
Tension the belt using the screw
(1).
• Reused belt
90 SEEM units.
• New belt
120 SEEM units.
Tighten the screws
(2)to 2 m.daN.
Remove the tool
[1].
Rotate the crankshaft by 3 turns
(direction of rotation).
Check the belt tension using the tool
[1], and adjust (if necessary).
Without air conditioning.
B1EP12YCB1EP12XC
Engine: RFS

Downloaded from www.Manualslib.com manuals search engine 128
ENGINEAUXILIARY EQUIPMENT DRIVE BELT 2002
Engines: 6FZ RFN
Without air conditioning.With air conditioning.
Tools.
[1]
Pliers for removing plastic pegs :7504T
Remove the belt.
Detension the belt (3)by turning the screw (2)of the tensioner roller (1)(anticlockwise).
The screw
(2) (WARNING: not left hand screw).
Remove the belt (3), while keeping the tensioner roller (1)tight.
Refit the belt. Refit the belt (3), while keeping the tensioner roller (1)tight.
Release the tensioner roller (1).
B1BP23PCB1BP23QCB1BP23PCB1BP23RC
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 130
ENGINEXSARAAUXILIARY EQUIPMENT DRIVE BELT 2002
Sans Powerassisted steering With air conditioning.
Tools.
[1]
Belt tension measuring instrument: 4122T
Removal.
Loosen the screws (1).
Tighten the screw
(2)until it is against its stop.
Remove the belt.
Refitting.
Refit the belt.
Fit the tool
[1]at "e".
Tighten the screw
(2)to obtain:106 ±10 SEEM units.
Tighten the screws (1)to 2 m.daN.
Remove the tool
[1].
B1BP1SGCB1BP1SFC
Engine: WJY

Downloaded from www.Manualslib.com manuals search engine 131
ENGINE
XSARA
AUXILIARY EQUIPMENT DRIVE BELT 2002
Powerassisted steering without air conditioning.
Tools.
[1]
Belt tension measuring instrument: 4122T
Removal.
WARNING: If the belt is to be reused, measure the tension before removal.
Loosen:
the screw
(1).
the nut
(2).
NOTE:The tensioner arm (3) must be against the alternator.
Remove the belt.
B1BP1SHD
Engine: WJY

Downloaded from www.Manualslib.com manuals search engine 132
ENGINEAUXILIARY EQUIPMENT DRIVE BELT
Engine: WJY
Powerassisted steering without air conditioning (continued).
XSARA
Refitting. Refit the belt.
Place the tool [1]on belt at "f".
WARNING: Position tool [1], with the knob downwards. Tighten the nut (2)to obtain a value of :
Reused belt:Keep the value taken at removal.
New belt:Tension should be 110 SEEM units.
Tighten the screw (1)to 9.5 m.daN.
Check belt tension, using tool [1].
Tension should be 144 ± 3 SEEM units.
Remove the tool [1].
Start the engine and run it for 10 seconds.
Stop the engine.
Place the tool
[1]on the belt at "f".
Tension should be 130 ± 4 SEEM units.
Remove the tool [1].
B1BP1SJD

Downloaded from www.Manualslib.com manuals search engine 133
ENGINE
XSARA
AUXILIARY EQUIPMENT DRIVE BELT 2002
Powerassisted steering with air conditioning.
Tools.
[1]
Dynamic tensioner peg: () 0188 H
[2]Belt tension measuring instrument: 4122T
Removal.
Peg the dynamic tensioner (1)at "a", using tool [1].
Loosen the screw (2)of the roller (3).
Turn the roller (3)backwards.
Remove the belt.
NOTE:If it can not be pegged at "a":
Loosen the screw (2)of the roller (3).
Using a 7 mmsquare drive, turn the roller (3)at "b".
Peg the tensioner (1)at "a", using tool [1].
NOTE:If the belt is broken:
Support the engine using a jack (insert a wooden block between the housing and the jack).
Remove the right engine support. Using a square drive at
(b)turn the tool (3)in the direction of the arrow "a", so that it can be
pegged at "a"using the tool [1].
B1BP1SKC
Engine: WJY

Downloaded from www.Manualslib.com manuals search engine 134
ENGINEAUXILIARY EQUIPMENT DRIVE BELT 2002
Powerassisted steering with air conditioning (continued).
Refitting.
Refit the belt.
Using a
7 mm squaredrive at "b", turn the roller (3), until the tool [1]located at "a"becomes
free.
Tighten the screw
(2).
Remove the tool
[1].
B1BP1SLC
Engine: WJY
XSARA

Downloaded from www.Manualslib.com manuals search engine 140
ENGINE
140
B1BP2Z6DB1BP2ZCD
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 9HZ 9HY
Tools.
[1]
Dynamic tensioner compression lever: ().0188.Z
[2]Peg for dynamic tensioner roller: ().0194.F
Removing.
Remove the front RH wheel, the underengine sounddeadening and the splashshield.
Vehicle with air conditioning.WARNING:Mark the direction of fitting of the accessories drive belt, if it is to be reused.
Compress the tensioner roller (1)by acting at «a»(clockwise), using tool [1].
Peg at «b», using tool [2].
Remove the accessories drive belt.
IMPERATIVE:Check that the rollers (1) and (2) can turn freely (without play and without tight spots).
Refitting.
WARNING:
Belt to be reused, mark the direction of fitting of the belt.
Refit the accessories drive belt.
Compress the tensioner roller
(1)by acting at «a»(clockwise), using tool [1].
Remove tool [2].
IMPERATIVE: Make sure the belt is correctly positioned in the grooves of the various pulleys.
Complete the refitting in the opposite order to removal.
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 141
ENGINE
XSARA XSARA PICASSO
A UXILIARY EQUIPMENT DRIVE BELT 2002
Engines: RHY RHZ
Without air conditioning.
B1BP1YKD
Tools.
[1]Belt tension adjusting square: ().0188 J2
[2] Ø 4 mmpeg: ().0188.Q1
[3] Ø 2 mmpeg: ().0188.Q2
[4]Dynamic tensioner compression lever:().0188.Z
Removal.
Reuse of belt.
WARNING: Mark the direction the belt was fiited in case of reuse of the same
belt.
Compress the tensioner roller (2)by action at «a»(in anticlockwise direction),
tool [4].
Keep the tensioner roller (2)compressed and remove the belt.
No reuse of belt. Compress the tensioner roller (2)by action at «a»(in anticlockwise direction),
tool [4].
Peg using tool [2], at «b».
Keep the tensioner roller (2)compressed and remove the belt.
Loosen the screw (1).