ignition Citroen BERLINGO FIRST RHD 2009 1.G User Guide

Page 39 of 115

41SEATS-
FRONT SEATS

The adjustment is correct when
the upper edge of the head
restraint is level with the top of
the head.
To remove the head restraint, place it
in the top position, press the tabs and
pull it upwards.
To put it back in position, locate the
stems of the restraint in the holes,
taking care to keep them in line with
the seat back.
No person or object must pre-
vent the seat from returning
to its initial position; return to
this position is necessary for
the seat to lock in place.
4. Forwards-backwards
adjustment
Lift the control and slide the seat for-
wards or backwards.
1. Head restraint height
adjustment
To raise or lower the restraint, slide it.
2. Armrests
These can be folded back. 3. Seat back angle adjustment
5. Storage drawer (version with
passenger air bag)
There is a storage drawer under the
front passenger seat.
To open it, lift it and pull. 6. Heated seats switch
Press the switch. The temperature is
controlled automatically.
Pressing the switch again stops opera-
tion.

Note: the command for activation of
heating of the seat(s) remains memo-
rised for two minutes after the ignition
has been switched off.
7. Access to rear seats (version with one
sliding side door only)
Lift the control to fold the seat back
and move the seat forwards.
On repositioning, the seat returns to
its initial position (driver’s side).
Do not place heavy objects
in the drawers.
A. Turn the knob.

B. Pull the lever (version
with one sliding side door
only).
Never drive with the head re-
straints removed; they must be
in place and correctly adjusted.

Page 49 of 115

SEATS50 -
SEAT BELTS
Locking the seat belts
Pull the strap, then insert the end into
the buckle.
Check that the seat belt is fastened
correctly by pulling the strap.
Unfastening the seat belts
Press the button on the buckle.
Front seat belts with
pre-tensioner
Safety in the event of frontal impacts
has been improved by the introduction
of pre-tensioning seat belts for the
front seats.
Depending on the seriousness of the
impact, the pre-tensioning system
instantly tightens the seat belts and
pulls them against the bodies of the
occupants.
The pre-tensioning seat belts are
armed when the ignition is on.
Seat belt height adjustment:
To lower or raise: slide the control
downwards or upwards. Rear seat belts
The rear seats are fi tted with three
three-point inertia reel seat belts
(two-part rear seat, 1/3 - 2/3).

Page 51 of 115

ACCESS and STARTING52 -
KEYS
The keys allow you to switch on the
ignition and operate the passenger
air bag disarming switch as well as to
independently operate the locks on
the doors and the fuel fi ller cap. Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:

 press button A , the courtesy lights
come on and the direction indica-
tors fl ash for a few seconds. Changing the battery of the
remote control
CR 2016/3 volt battery.
The information "battery fl at" is given by
an audible signal accompanied by the
message
"Remote control battery
fl at" on the screen.
To change the battery, unclip the casing
using a coin at the ring.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Programming the remote
control

 Switch off the ignition.

 Switch the ignition on again.

 Press button A immediately for a
few seconds.

 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control
is now working again.
Remote control
Central locking
From the front doors, the keys allow
you to lock and unlock the doors.
If one of the doors is open, the central
locking does not work.

The remote control performs the
same functions at a distance. Locking
Press button
A to lock the vehicle.
This is confi rmed by fi xed lighting of the
direction indicators for approximately
two seconds.
Unlocking
Press button B to unlock the vehicle.
This is confi rmed by rapid fl ashing of
the direction indicators.

Note: if the vehicle is locked and
unlocking is activated inadvertently,
unless the doors are opened within
30 seconds, the vehicle will lock au-
tomatically.

Page 52 of 115

53ACCESS and STARTING-
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system as
soon as the ignition has been switched
off and therefore prevents starting of
the vehicle by anyone who does not
have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
must be recognised for the vehicle to
start.

If the system does not function
correctly, the central locking button
indicator light, situated in the centre
of the fascia, fl ashes rapidly when the
ignition is switched on (2nd notch),
accompanied by an audible signal
and a message on the display.
In this case your vehicle will not
start.
Contact a CITROËN dealer as soon
as possible.
Key in ignition
A buzzer sounds on opening the
driver’s door, if the key has been left
in the ignition. Make a careful note of the
number of each key. This
number is coded on the label
attached to the key.
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reprogramming.
Do not operate the deadlocking
function if there is anyone inside the
vehicle.
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
more diffi cult in an emergency.
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time.
Do not repeatedly press the buttons
of your remote control out of range of
your vehicle.
You run the risk of stopping it from
working and the remote control would
have to be reprogrammed.
When purchasing a second-hand ve-
hicle, have the key codes memorised
by a CITROËN dealer, to ensure that
the keys in your possession are the
only ones which can start the vehi-
cle.
Do not make any modifi cations to the
electronic engine immobiliser system. If the keys are lost
Visit a CITROËN dealer with the ve-
hicle's V5 registration certifi cate and
your personal identifi cation docu-
ments.
The CITROËN network will be able to
retrieve the key code and the trans-
ponder code to order a replacement
key.

Page 53 of 115

ACCESS and STARTING52 -
KEYS
The keys allow you to switch on the
ignition and operate the passenger
air bag disarming switch as well as to
independently operate the locks on
the doors and the fuel fi ller cap. Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:

 press button A , the courtesy lights
come on and the direction indica-
tors fl ash for a few seconds. Changing the battery of the
remote control
CR 2016/3 volt battery.
The information "battery fl at" is given by
an audible signal accompanied by the
message
"Remote control battery
fl at" on the screen.
To change the battery, unclip the casing
using a coin at the ring.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Programming the remote
control

 Switch off the ignition.

 Switch the ignition on again.

 Press button A immediately for a
few seconds.

 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control
is now working again.
Remote control
Central locking
From the front doors, the keys allow
you to lock and unlock the doors.
If one of the doors is open, the central
locking does not work.

The remote control performs the
same functions at a distance. Locking
Press button
A to lock the vehicle.
This is confi rmed by fi xed lighting of the
direction indicators for approximately
two seconds.
Unlocking
Press button B to unlock the vehicle.
This is confi rmed by rapid fl ashing of
the direction indicators.

Note: if the vehicle is locked and
unlocking is activated inadvertently,
unless the doors are opened within
30 seconds, the vehicle will lock au-
tomatically.

Page 54 of 115

SPECIAL FEATURES
112 -
THE ALARM SYSTEM*
The alarm offers two types of protection:
- exterior protection: the alarm
sounds if a door, the boot or the
bonnet is opened ;
-
interior protection: the alarm sounds if
there is a variation in the volume inside
the vehicle (breaking of a window or
movement inside the vehicle) .
Setting the alarm
Switch the ignition off and get out of
the vehicle.
Activate the alarm within five minutes
following your exit from the vehicle,
by locking using the remote control
key (the red indicator light on the
switch 1, which can be seen from the
outside, flashes once a second). When the alarm is triggered, the siren
sounds and the direction indicators
flash for thirty seconds.
After it has been triggered, the alarm
becomes operational again.
Note:
if you wish to lock your vehicle
without setting the alarm, lock it using
the key in the door lock.
Warning
If, on setting the alarm, a door, the
boot or the bonnet are not closed
correctly, the siren sounds for a mo-
ment.
Close the vehicle correctly to set the
alarm.
If the interior protection alarm is trig-
gered ten times in succession, it is
disarmed automatically. It must be
set again in order for it to operate
correctly.
Disarming the alarm
Unlock the vehicle using the remote
control key (the red indicator light on
the switch 1 goes out).
Note: if the warning light flashes, it is
a sign that the alarm has been trig-
gered in your absence.
To stop it, switch on the ignition. Note:
when the alarm is set, but the
remote control no longer works:
 unlock the doors using the key
and open the door; the alarm is
triggered;
 switch the ignition on within ten
seconds; the alarm is disarmed.
To set the alarm with exterior
protection only.
If, while you are away from the vehicle,
you wish to leave a window partially
open or a pet inside the vehicle, you
need to select exterior protection only:


Page 55 of 115

53ACCESS and STARTING-
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system as
soon as the ignition has been switched
off and therefore prevents starting of
the vehicle by anyone who does not
have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
must be recognised for the vehicle to
start.

If the system does not function
correctly, the central locking button
indicator light, situated in the centre
of the fascia, fl ashes rapidly when the
ignition is switched on (2nd notch),
accompanied by an audible signal
and a message on the display.
In this case your vehicle will not
start.
Contact a CITROËN dealer as soon
as possible.
Key in ignition
A buzzer sounds on opening the
driver’s door, if the key has been left
in the ignition. Make a careful note of the
number of each key. This
number is coded on the label
attached to the key.
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reprogramming.
Do not operate the deadlocking
function if there is anyone inside the
vehicle.
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
more diffi cult in an emergency.
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time.
Do not repeatedly press the buttons
of your remote control out of range of
your vehicle.
You run the risk of stopping it from
working and the remote control would
have to be reprogrammed.
When purchasing a second-hand ve-
hicle, have the key codes memorised
by a CITROËN dealer, to ensure that
the keys in your possession are the
only ones which can start the vehi-
cle.
Do not make any modifi cations to the
electronic engine immobiliser system. If the keys are lost
Visit a CITROËN dealer with the ve-
hicle's V5 registration certifi cate and
your personal identifi cation docu-
ments.
The CITROËN network will be able to
retrieve the key code and the trans-
ponder code to order a replacement
key.

Page 57 of 115

55ACCESS and STARTING-
Locking from the inside
Lower or raise control C to lock or
unlock from the inside. Locking from the inside
Pressing control
D operates the
central locking, when the doors are
closed. Automatic central locking
Your vehicle can lock automatically
while driving (speed greater than
6 mph (10 km/h)). You can activate or
deactivate this function.
Unlocking from the inside
Press control D .
It is still possible to open the doors
from the inside. Activation
Press and hold control
D .
Activation of the function is accom-
panied by an audible signal and a
message on the display.
Deactivation
Press and hold control D .
Deactivation of the function is accom-
panied by an audible signal.

Notes:
- doors locked and ignition off: the indicator light fl ashes,
- doors locked and ignition on: the indicator light remains on.

Page 62 of 115

59VISIBILITY-
Dipped/Main beam change
Pull the stalk towards you.

Note: with the ignition off, when the
driver’s door is opened, a buzzer
sounds if you have left your lights on.
LIGHTS STALK
Lights off
Side lights
Dipped/main beam
headlamps Front fog lamps and rear fog
lamp
Rotate the ring forwards to switch on
and backwards to switch off. The sta-
tus is confi rmed by the indicator light
on the instrument panel.
"Follow-me-home" lighting
In poor light, or at night, if you leave
your vehicle, the side lights and
dipped headlamps may remain on for
approximately one minute.
To activate this function:
- place the key in the
STOP position,
- place the lights stalk in position 0 ,
- fl ash the headlamps,
- exit the vehicle and lock it.
In good or rainy weather,
both day and night, the front
fog lamps and the rear fog
lamp are dazzling and are
prohibited.
Do not forget to switch them
off when they are no longer needed.
Left: downwards.

Right: upwards.
Direction indicators (fl ashers)
Vehicles fi tted with a rear
fog lamp only (ring B)
Vehicles fi tted with
front fog lamps and
a rear fog lamp
(ring B)
Front fog lamps (fi rst rotation of the
ring forwards).
Front and rear fog lamps (2nd rotation
of the ring forwards).

Note: to switch off the rear fog lamp
and the front fog lamps, turn the ring
backwards twice in succession.
Front and rear lights
Selection is by turning ring
A .
Rotate the ring forwards.
This only operates with the dipped/
main beam headlamps.

Page 64 of 115

61-
ELECTRIC WINDOWS
Always remove the ignition
key when leaving the vehi-
cle, even for a short time.
If an obstacle is encountered
while the electric windows
are in use, you must reverse the
movement of the window. To do this,
press the switch concerned.
When the driver operates the pas-
senger electric window switches, he
must ensure that no one is preven-
ting correct closing of the windows.
The driver must ensure that passengers
use the electric windows correctly.
Be aware of children when operating
the windows.
1. Driver’s electric window switch
2. Passenger electric window switch
You have two options:
- Manual operation:
Press switch 1 . The window
stops as soon as the switch is
released.
- Automatic operation (driver):
Press and hold switch 1 . One
touch completely opens or closes
the window.
Automatic closing only operates when
the engine is running.
REAR WINDOWS
To partially open the rear windows,
tilt the lever and push it fully to lock
the windows in the open position.

Page:   < prev 1-10 11-20 21-30 next >