warning Citroen BERLINGO MULTISPACE RHD 2017 2.G User Guide

32
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
WARNING LAMPS
Warning lamp is indicatesSolution - action
STOP on, associated
with another
warning
lamp and
accompanied
by a message
in
  the   screen.major
  faults   linked   with  
the

  "Brake   fluid   level",  
"Engine oil pressure and
temperature", "Coolant
temperature", "Electronic
brake

  force   distribution"   and  
"Power steering" warning
lamps.Y

ou must stop as soon as it is safe to do
so. Park and switch off the ignition. Have it
checked by a CITROËN dealer or a qualified
workshop.
Parking
brake
/
Brake fluid
level
/ EBFDon.
that the
 parking  brake  is  applied or
  has   not   been   released   fully.Releasing the parking brake switches off the warning  lamp.
on. low
 
brake
 
fluid
 
level. Top   up   using   a   fluid   recommended   by   CITROËN.
remaining on even
though the level
is correct and
associated with the
ABS
 
warning
 
lamp.
a fault with the electronic
brake  force   distribution. You must stop as soon as it is safe to do so.
Park and switch off the ignition.
Have it checked by a CITROËN dealer or a
qualified workshop.
Engine oil
pressure and
temperature on while
driving.
low pressure or a high
temperature. Park
  and   switch   off   the   ignition   then   allow   to   cool.
Visually
  check   the   level.
Chapter
  7,   "Levels"   section.
remaining on,
even though the
level  is   correct.a major fault. Have   it   checked   by   a   CITROËN   dealer   or   a  qualified
  workshop.
Each
 
time
 
the
 
vehicle
 
is
 
started:
 
a
 
series
 
of
  warning   lamps   comes   on   applying   a   self-test   check.  
They
  go   off   almost  
immediately

.
Engine
 
running:
 
the
 
lamp
 
becomes
 
a
 
warning   if   it   remains   on   continuously   or   flashes.
This
 
initial
 
warning
 
may
 
be
 
accompanied
 
by   an   audible   signal   and   a   message   in   the   screen.
Do
 
not
 
ignore
 
these
 
warnings.

33
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Warning lamp isindicatesSolution - action
Coolant
temperature
and level on with needle
in the red
zone.
an abnormal increase in
temperature.
Park
  and   switch   off   the   ignition   then   allow   to   cool.  
V

isually   check   the   level.
flashing. a
  drop   in   the   coolant   level.Chapter
  7,   "Levels"   section.
Contact
  a   CITROËN dealer   or   a   qualified  
workshop.
Service on

  temporarily. minor   faults   or   warnings.Consult
  the   alert   log   in   the   display   or   screen.
If your vehicle is equipped with a trip computer or
a
  screen:   refer   to   the   "Steering   mounted   controls"  
section

  in   Chapter   4.
Contact
  a   CITROËN   dealer   or   a   qualified  
workshop.
remaining

  on. major   faults.
Seat belt not
fastened on then
flashing.
the
  driver   and/or   front  
passenger has not fastened
their

  seat   belt.Pull
  the   strap   then   insert   the   tongue   in   the   buckle.
accompanied
by an audible
signal then
remains
  on.the vehicle is moving with
the
  driver's   and/or   front  
passenger's seat belt not
fastened.Check

  that   the   seat   belt   is   fastened   by   pulling   the  
strap.
Chapter

  5,   "Seat   belts"   section.
ECO on.
The Stop & Start
system
has put the engine in STOP
mode following a vehicle
stop
  (red   light,   traffic   jam,  
etc...).As soon as you want to move of

f, the warning
lamp goes off and the engine restarts
automatically
  in   START
 
mode.
flashes
  for   a  
few seconds,
then

  goes   off.STOP mode is temporarily
unavailable.
or
START mode has been
invoked
  automatically.Chapter
  3,   "Stop   &   Start"   section.
READY TO GO
3

34
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Warning lamp isindicatesSolution - action
Front / lateral
airbag flashing
  or  
remaining

  on.a
  failure   of   an   airbag.Have
  the   system   checked   by   a   CITROËN   dealer  
or

  a   qualified   workshop   without   delay.
Chapter
  5,   "Airbags"   section.
Front
passenger's
airbag
deactivated on. the intentional deactivation
of this airbag in the
presence of a rearward
facing
  child   seat.Chapter
  5,   "Airbags"   or   "child   safety"   section.
Low fuel
level on with gauge
needle in the
red
  zone.When
  it   first   comes   on,  
there remains around
8 litres

  of   fuel   in   the   tank.  
The distance you can drive
on this fuel depends on
your style of driving and the
engine

  type.You
  must   fill   up   with   fuel   to   avoid   running   out.
This warning lamp comes on each time you
switch
  on   the   ignition   until   you   have   filled   up.
Capacity
  of   the   tank:   approximately   60   litres   (or  
55

  litres   according   to   version).
Never
  risk   driving   until   the   tank   is   empty,   this  
could

  damage   the   emissions   and   injection  
systems.
flashing. cutting of

f of the fuel supply
following
  a   serious   impact.Restore
  the   supply.
Chapter
  7,   "Fuel"   section.
EOBD
emission
control
system flashing
  or  
remaining

  on.a
  failure   of   the   system.There
  is   a   risk   of   damage   to   the   catalytic  
converter

.   Have   it   checked   by   a   CITROËN  
dealer

  or   a   qualified   workshop.
Battery
charge on.
a fault in the charging
circuit. Check
  the   battery   terminals,   …
Chapter
  8,   "Battery"   section.
flashing. placing of the active
functions on standby
(economy
  mode).Chapter
  8,   "Battery"   section.
remaining on,
in spite of the
checks. an
  ignition   or   injection  
malfunction.Have

  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.

+
ABS
35
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Warning lamp isindicatesSolution - action
Power
steering on. a fault with the
system.
The vehicle
 retains  conventional  steering  without  assistance. Have
  it   checked   by   a   CITROËN   dealer   or   a   qualified workshop.
Door open
detectionon and accompanied
by a message in the
screen. that a door is not
closed
  correctly.Check
  that   all   of   the   doors   are   closed.
ABS remaining
  on.a fault with the anti-
lock
  braking   system.The
  vehicle   retains   conventional   braking.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.
ESC flashing.
triggering of the ASR
or
  DSC   regulation.The system optimises traction and improves the
directional
  stability   of   the   vehicle.
Chapter
  5,   "Driving   safety"   section.
remaining
  on.a fault with the
system.
E.g.:
  under-inflation  
of

  the   tyres.E.g.:
  check   the   pressure   of   the   tyres.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.   (Wheel   speed   sensor,  
hydraulic

  valve   block,   ...).
Under-
inflation on.
the tyre pressure is
too low in or more
wheels.Check
  the   tyre   pressure   as   soon   as   possible.
This
  check   must   be   done   with   the   tyres   cold.
flashing
  then
 remaining on,


accompanied by the
Service warning
lamp, and depending
on equipment, the
display
  of   a   message.the tyre pressure
monitoring system
has a fault or one of
the wheels does not
have
  a   sensor.Detection
  of   under-inflation   is   no   longer   assured.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.
Particle filter on. a problem with the
particle
  filter   (fuel  
additive

  level,   risk   of  
blockage, ...).Have

  the   filter   checked   by   a   CITROËN   dealer   or  
a

  qualified   workshop.
Chapter
  7,   "Levels"   section.
READY TO GO
3

36
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Warning lamp isindicatesSolution - action
Dipped beam
headlamps
/
Daytime
running
lamps on.a manual selection or
automatic illumination of
headlamps.
Turn
  the   ring   on   the   lighting   control   stalk   to   the  
second

  position.
illumination of the dipped beam headlamps
from  the   time   the   ignition   is   switched   on: daytime running lamps (depending on the


country
  in   which   the   vehicle   is   sold).
Chapter 4, "Steering mounted controls" section.
Main beam
headlamps pullin
g
 
of
 
the
 
stalk
 
towards
 
you. Pull

  the   stalk   to   return   to   dipped   beam  
headlamps.
Direction
indicators flashing

 
with
 
audible

 
signal. a change of direction via
the
 
lighting
 
stalk. Flashing
  right:   push   stalk   downwards.
Flashing
  left:   push   stalk   upwards.
Front
foglamps on.
a
 
manual
 
selection. The foglamps only operate if the sidelamps or
dipped
  beam   headlamps   are   on.
Rear
foglamps on.
a
 
manual
 
selection. The foglamps only operate if the sidelamps or
dipped
  beam   headlamps   are   on.
In conditions of normal visibility, switch them off
to
  avoid   breaking   the   law.
"This
  lamp   is   a   dazzling   red".

37
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Warning lamp
in the screenis
indicates Solution - action
Cruise
control on.
cruise
  control   selected.Manual
  selection.
Chapter
  4,   "Steering   mounted   controls"   section.
Speed limiter on.speed
  limiter   selected.Manual
  selection.
Chapter
  4,   "Steering   mounted   controls"   section.
Gear shift
indicator on.a recommendation
independent of the type and
density
  of   traffic.To reduce fuel consumption, change to an
appropriate
  gear   with   a   manual   gearbox.
The driver retains responsibility to follow this
indication
  or   not.
Diesel
pre-heating on.climatic conditions requiring
pre-heating. Wait until the warning lamp goes off before
operating
  the   starter.
Presence of
water in the
Diesel filter
on and
accompanied by
a message in
the
  screen.
water in the Diesel filter. Have   the   filter   bled   by   a   CITROËN   dealer   or   a  qualified
  workshop   without   delay.
Chapter   7,   "Checks"   section.
According
  to   country.
Service
spanner on.that a service will be due
shortly. Refer
  to   the   list   of   checks   in   the   maintenance   and  
warranty

  guide.
Have the service carried out by a CITROËN
dealer
  or   a   qualified   workshop.
Time flashing. adjustment
  of   the   time.Use
  the   left-hand   button   on   the   instrument   panel.
Chapter
  3,   "Instruments   and   controls"   section.
READY TO GO
3

+
38
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
AdBlue®
For more information on filling, refer to the chapter 7, AdBlue® section.
Alert
Information Solution - action
1
st level of alert
There is an audible signal when the ignition is switched on.
The warnings are intermittent and then become
permanent   when   switching   on   the   ignition   or   when   driving.
The remaining driving range is counted down from
1  500   miles   (2   400   km)   to   375   miles   (600   km).
The range figure reduces in steps of 200 miles (300 km).
The contents of the AdBlue® tank has dropped to a level
 
sufficient
 
for
 
a
 
range
 
of   less   than   1   500   miles  
(2

 
400
 
km).
Have
 
the
 
fluid
 
topped-up
 
using   an  
AdBlue®
container
 
or
 
bottles.
2
nd level of alert
There is an audible signal when the ignition is
switched
  on.
The warnings are intermittent (every 30 seconds)
and then become permanent every time the ignition
is
 
switched   on   or   when   driving.
The remaining driving range is counted down from 350 miles
(600  km)   to   zero,   reducing   in   steps   of   30   miles   (50   km).
You must have the AdBlue® topped-up and not wait
for
 
a
 
breakdown.
In the display
screen. Temporary
 
display:
 
"NO START IN".
In the touch
screen
 
tablet. Select:
-
 
"Driving

 
assistance".
-
 
"Diagnostic". The

 
driving
 
range
 
is
 
displayed.
3
rd level of alert
The AdBlue® tank is empty. Starting is impossible.
It is essential to add at least 3.8 litres of AdBlue®
additive
 
to
 
the
 
additive
 
tank.

+ +
39
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
SCR emissions control system
Alerts InformationSolution - action
The UREA, Service and diagnostic warning lamps
come on, an SCR emissions control system fault
has
  been   detected. This is is temporary fault, the alert disappears as
soon as the exhaust emissions return to normal
levels.
After 30 miles (50 km) without AdBlue
®
Confirmation of the fault which is not related to a lack   of   fluid. The
  remaining   driving   range   700   miles  
(1   100   km).
Go   to   a   CITROËN   dealer   or   a   qualified   workshop  
as

  soon   as   possible   to   avoid   a   breakdown.
The
  fault   is   confirmed.
The next time the ignition is switched on, the
authorised driving range will be displayed in miles
(kilometres)
  and   the   alert   will   be   repeated   every  
30
  seconds.
The limit of the driving range has been reached,
exhaust
  emissions   levels   are   above   the   limits.
Starting
  is   impossible. To restart the engine, you must contact a
CITROËN
  dealer   or   a   qualified   workshop.
- BlueHDi Diesel
READY TO GO
3

40
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
FUEL GAUGEC OOLANT TEMPERATURE
The needle is positioned before the
red zone:
  normal   operation.
In arduous conditions of use or hot
climatic conditions, the needle may
move
  close   to   the   red   graduations.What you should do if the needle
enters the red zone:
Reduce your speed or let the engine
run
  at   idle.
What you should do if the warning
lamp comes on:
-
stop immediately
, switch off the
ignition.  
The
  fan   may   continue   to  
operate for a certain time, up to
approximately 10 minutes,
-

wait for the engine to cool down in
order

  to   check   the   coolant   level   and  
top

  it   up   if   necessary.
As the cooling system is pressurised,
follow the procedure below to avoid the
risk   of   scalding:
-
wait at least one hour after
switching of

f the engine before
carrying   out   any   work,
-  
unscrew
  the   cap   by   1/4   turn   to  
allow the pressure to drop,
-

when the pressure has dropped,
check

  the   level   in   the   header   tank,
- if necessary , remove the cap to
top up.
If the needle remains in the red
zone,
  have   the   system   checked   by  
a

  CITROËN   dealer   or   a   qualified  
workshop.Refer

  to   chapter   7,   "Levels"  
section.
Refer

 
to
 
chapter
 
7,
 
"Fuel"
 
section.
The fuel level is tested each time the
key
 
is
 
turned
 
to
 
the
 
"running"
 
position.
The
 
gauge
 
is
 
positioned
 
on:
-

1:

 
the
 
fuel
 
tank
 
is
 
full,
 
approximately

 
60
 
litres.
-

0:

the reserve is now being used,
the warning lamp comes on
continuously.
 
The

 
reserve
 
when
 
the

 
warning
 
first
 
comes
 
on
 
is
 
approximately

 
8
 
litres.

41
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
EMISSIONS CONTROLS
EOBD (European On Board
Diagnosis) is a diagnostics
system which complies with,
among others, the standards
on  emissions   limits   of:
-

CO (carbon monoxide),
-


HC (unburnt hydrocarbons),
-


NOx (nitrogen oxides), detected
by oxygen sensors placed
downstream of the catalytic
converters,
-

 
particles.
UNDER-INFLATION DETECTION
This system
continuously monitors
the pressures of the four
tyres, as soon as the
vehicle   is   moving.
A pressure sensor is located in the
valve of each tyre (except the spare
wheel).
The system triggers an alert if a drop
in pressure is detected in one or more
tyres.
The
 
tyre
 
under-inflation   detection  
system is an aid to driving which
does not replace the need for
vigilance

 
on   the   part   of   the   driver.
The driver is warned of any
malfunction of this emissions
control system by the illumination
of this warning lamp in the instrument
panel.
If this warning lamp comes on, have
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or
 
a
 
qualified

 
workshop. This system does not avoid the
need
  to   check   the   tyre   pressures  
regularly (including the spare
wheel)

  and   before   a   long   journey.
Driving
  with   under-inflated   tyres  
adversely af

fects road holding,
extends
  braking   distances   and   causes  
premature tyre wear

, particularly under
arduous conditions (vehicle loaded,
high
  speed,   long   journey).
Driving
  with   under-inflated   tyres  
increases

  fuel   consumption.
The tyre pressures for your vehicle
can be found on the tyre pressure
label.
Refer
  to   chapter   9,   "Identification  
markings"

  section.
The
  tyre   pressures   must   be   checked  
when the tyres cold (vehicle stopped
for 1 hour or after driving for less then
6

  miles   (10   km)   at   moderate   speed).
Otherwise,
  add   0.3   bar   to   the   values  
indicated

  on   the   label.
READY TO GO
3