change time Citroen C CROSSER 2008 1.G Owner's Manual

I N S T R U M E N T S a n d C O N T R O L S
I
32
System which provides current infor-
mation about the route travelled.
TRIP COMPUTER Average consumption (l/100km or km/l or
mpg)
This is the average
quantity of fuel consumed
since the last zero reset.
This fi gure may increase following a
change in the style of driving or the
relief resulting in a reduction in the
current consumption.
Average speed
(km/h or mph)
This is the average
speed calculated since
the last zero reset.
Resetting the information to zero
Automatic
If the ignition remains in the “ACC”
(Accessories) position for at least
4 hours, the average consumption value
is reset to zero automatically.
If dashes “---” are displayed for long
periods in place of the digits while
driving, contact a CITRÖEN dealer. Current consumption (l/100km or km/l or
mpg)
This is the average
quantity of fuel con-
sumed during the last
few seconds of driving.
Data displays
With the ignition on, press the INFO
button on the fascia, to the right of
the instrument panel, several times
in succession to display the different
information:
- the average consumption,
- the average speed,
- the current consumption. When the required information is
displayed, press the
INFO button for
more than two seconds.

When the ignition is switched on, the
zero reset switches automatically from
manual mode to automatic mode.

I N S T R U M E N T S a n d C O N T R O L S
I
33

When the vehicle is
stationary , it allows
the user to change the
following parameters:
- the choice of the reini-
tialisation of the average
consumption and aver-
age speed,
- the fuel consumption unit,
- the temperature display unit,
- the display language,
- activation/deactivation of the INFO
button sound,
- the break (rest) reminder display in- terval,
- restore the manufacturer’s param- eters.
FUNCTION PARAMETERS
System which provides access to
certain function parameters.
In order to change the settings,
it is essential that you stop
the vehicle and switch on the
ignition.
Apply the handbrake and place the
gear lever in neutral.

When the vehicle is moving ,
the functions setting display is not
displayed when you press the INFO
button.

With the ignition on , press the
INFO
button on the fascia, to the right of
the instrument panel, several times in
succession until the “SETTING MENU”
screen is displayed. Operation

 press and hold the INFO button for
a few seconds to display the menus
screen. Press and hold the
INFO button
for a few seconds to return to the
previous screen.
When the menus screen is displayed,
if no operation is carried out within
15 seconds, the function parameters
screen is displayed.

 on the menus screen, press the

INFO button to select a function
from the list:

MENU 1/2 :
- 1 - 2 (choice of the reinitialisation of
the average consumption and aver-
age speed) ,
- UNIT (choice of the fuel consump-
tion units) ,
- choice of the temperature display
unit ,
- LANGUAGE (choice of the display
language),

MENU 2/2:
- a/b (choice of displaying a different
language on the instrument panel
display and the navigation display),
- activation / deactivation of the
INFO
button sound ,
- ALERT (changing of the “BREAK
ADVISED” break reminder display
interval),
- REINITIALISE (restore the manu-
facturer’s parameters). Choice of the reinitialisation of
the average consumption and
average speed
You can choose between two average
consumption and average speed
reinitialisation modes:
-
automatic reinitialisation (
choice 1) ,
- manual reinitialisation (choice 2) .
On the menus screen:

 press the INFO button to select:

 press and hold the INFO button
for a few seconds to switch in suc-
cession from reinitialisation mode

1
(automatic) to reinitialisation
mode
2 (manual) .
The mode selected is confi rmed.

I N S T R U M E N T S a n d C O N T R O L S
I
36
Restoring the manufacturer’s
parameters (REINITIALISE)
You can restore all of the manufacturer’s
settings for all of the functions.
On the menus screen:

 press the INFO button to select
“REINITIALISE”

(located on menu
2/2) .

 press and hold the
INFO button for

at least 5 seconds .
An audible signal is heard and all of the
manufacturer’s settings are restored for
all of the functions. The manufacturer’s settings are: LIGHTING RHEOSTAT
With the lights on or off, press the button
to change the intensity of the lighting of
the instruments and controls in “day” or
“night” mode.
When the lighting reaches the maximum
setting, press again to change to the
minimum setting.
When the lighting reaches the required
intensity, release the button.
The setting is saved when the ignition
switch is turned to OFF. An audible signal is heard and the
intensity of the lighting increases
each time the button is pressed.
System for manual adjustment of the
brightness of the instruments and
controls in relation to the exterior
brightness.

Functions
Manufacturer’s
setting
Reinitialisation
of the average
consumption and
average speed
1 (automatic)
Fuel consumption
units
L/100 km
Temperature
display unit
°C
Display language ENGLISH
INFO button
sound
ON (activated)
Displaying of the
“BREAK ADVISED”
message
OFF (deactivated)

I N S T R U M E N T S a n d C O N T R O L S
I
39
COLOUR DISPLAY
This permits displaying of the following
main menus: On the control panel, press button
B
(SET) to access the “Settings” screen
and select:
- “Display Deactivated” to switch
off the display,
- “Sound control” for the sound dis-
tribution or volume, the type of mu-
sic and the sound fi eld (surround),
- “Picture control” to set the colour,
the intensity, the brightness, the
contrast and the level of black,
- “System” to change the time zone,
the language, the units and other
settings,
- “Wide Screen” to change the size
of the DVD picture to 4/3 format,
wide screen mode, centred wide
screen mode or enlargement,
- “Equipment” to set certain equip-
ment offered in the vehicle,
- “Col Contrast” to select the con-
trast of the display in relation to the
exterior light (Day, Night or Auto),
- “TP standby” to activate or deacti-
vate the traffi c information.
“Audio-video” menu
“Navigation-guidance” menu
On the control panel, press button A
(MODE) to access the “AV mode”
screen and select:
- the radio (FM, MW, LW),
- the CD (audio, MP3 or WMA),
- the Music Server,
- the DVD,
- the Auxiliary (Rear Display). “Settings” menu
On the control panel, press button C
(MENU) to access the “Menu” screen
and select:
- “Address/Junction” to search for
a location using the address or the
name of the street,
- “POI name” to search for a location
using the name of a point of interest
(POI),
- “Advanced search” to search for a
location using an advanced search
based on a POI,
- “20 Previous” to search for a
location using one of the 20 previous
destinations,
- “Address book” to search for a
location using a stored address,
- “Return to the initial screen” to
enter a return home,
- “Navigation settings” to set
functions linked with the navigation,
- “Navigation tools” to access
the basic information or a pre-set
demonstration.
The “CD” and “DVD” buttons are
active if you insert a CD or DVD in
the player.

I N S T R U M E N T S a n d C O N T R O L S
I
40
Setting the time
The digital clock is set automatically .
This mode enables the system to set
the local time automatically using the
signal from the RDS stations.

 On the control panel, press button

A (SET) to access the “Settings”
menu.

 On the touch screen, press button

B to access the “System” menu.
The system settings screen is
displayed.
“Information” menu
On the control panel, press button
D
(INFO) to access the “Info” screen and
consult:
- “Support info” to display the
software and data versions,
- “Vehicle position” to display the
GPS location of the vehicle,
- “Calendar” to make a note of events,
birthdays, etc.,
- “Journey” to display the average
speed, the consumption, the
distances and the duration of driving,
- “Environment” to display the
altitude, the atmospheric pressure,
the exterior temperature (the ice
symbol is displayed if there is a risk
of ice),
- “Air conditioning” to display
the information relating to the air
conditioning,
- “Mobile telephone” to enter a
number, delete a character, make or
receive a call. “Map” menu
On the control panel, press button
E
(NAVI) to access the “Routes Menu”
screen and select:
- “Detour” to make a detour through
a specifi ed region,
- “Route” to change the route,
- “Display a route” to display a route
in different ways,
- “Delete a route” to delete a route,
- “Local POI” to search for the POIs
in the surrounding area.

I N S T R U M E N T S a n d C O N T R O L S
I
41

1.
RDS Auto Correction:
Activate / deactivate the automatic
adjustment.

2.
GMT / GMT+1 / GMT+2
Select the time zone.

3.
Summer Time:
Activate / deactivate summer time.

 Press button D to confi rm and re-
turn to the previous menu.

 Press button C to access the “Time”
menu .
Once this menu has been selected, you
can access the following functions: It is essential to deactivate the
automatic adjustment (RDS Auto
Correction) in order to be able to
change the time zone and summer
time.
On each screen, you can return to
the previous screen by pressing
button
D “Return” .
Select the “AV Mode” menu by
pressing the “MODE” button on the
control panel.
From the “AV MODE” menu on the
touch screen, press:
- the “RearDisplay” button to access
the Auxiliary menu,
- the “Video parameters” button to
set the display format, the brightness,
the contrast and the colours.
VIDEO MENU
You can connect video equipment
(camcorder, digital camera, etc.) to the
three video sockets located on the back
of the front central armrest.
Video sources can only be displayed
when stationary.
Press the “Back” button to exit video
mode.

C O M F O R T
II
42
For even air distribution, take care not
to obstruct the exterior air intake grille
located at the bottom of the windscreen,
the vents, the air outlets under the front
seats and the air extractor located be-
hind the fl aps in the boot. The water formed by the air conditioning
condensation is discharged via an open-
ing provided for this purpose. Therefore,
a puddle of water may form underneath
the vehicle when stationary.
If the system does not produce cold air,
do not use it and have it checked by a
CITROËN dealer.
THE AIR CONDITIONING
Do not cover the temperature and hu-
midity sensor
2 and the sunshine sen-
sor
7 .
They are required for regulation of the
air conditioning.
Advice on operation
In hot weather, in order to obtain in-
tense ventilation, it is advisable to
use vents 1 and
4 only.
If, when the vehicle has been parked
in the sun for a long time, the interior
temperature remains very high, do
not hesitate to ventilate the passen-
ger compartment for a few minutes. Switch off the air conditioning when
the climatic conditions permit.
Use of the automatic regulation of the
air conditioning is recommended. It per-
mits automatic and optimised control of
all of the following functions: air fl ow,
passenger compartment temperature
and air distribution, by means of vari-
ous sensors (exterior temperature, in-
terior temperature, sunshine), so pre-
venting the need for you to change your
reference settings other than the value
displayed.
In certain cases of particularly arduous
use (towing the maximum load on a
steep gradient in hot weather), cutting
off the air conditioning permits recovery
of the engine power and therefore im-
provement of the towing capacity.
Close the windows to benefi t from the
full effectiveness of the air condition-
ing.
Ensure that the passenger compart-
ment fi lter is in good condition. Have
the fi lter elements replaced periodically.
If you drive in a dusty environment, re-
place it twice as often.
The air conditioning system does not
contain chlorine and is not harmful to
the ozone layer.
Operate the air conditioning system for
5 to 10 minutes, once or twice a month,
to keep it in perfect working order.
1. Centre panel vents.

2. Temperature sensor .

3. Air outlet to passenger footwells.

4. Side vents.

5. Front windows de-icing or demisting
vents.

6. Windscreen de-icing or demisting
vents.

7. Sunshine sensor.

C O M F O R T
II
46
Air conditioning On / Off (5)

 Press button 5 to activate the air
conditioning.
The indicator light comes on.
Intake of exterior air / Recirculation of interior air (4)

This function insulates the passenger
compartment from exterior odours and
smoke.

 Press button 4 to select the air in-
take mode.
When the indicator light on button 4 is
off, the exterior air intake function is ac-
tivated.
When the indicator light on button 4 is
on, the intake of exterior air is deacti-
vated and the system is in air recircula-
tion mode.
Do not drive for long periods in in-
terior air recirculation mode, except
in truly exceptional atmospheric
conditions. Personalisation of the Exterior air
intake / Interior air recirculation
function
This function is controlled automati-
cally. However, you can deactivate its
automatic control if you wish to change
the air intake mode at any time.
Personalisation of the Air
Conditioning On / Off function
This function is controlled automati-
cally. However, you can deactivate its
automatic control if you wish to activate
or deactivate the air conditioning at any
time.
The settings are retained, even after
switching off the ignition.
Changing the status
Press the Air Conditioning On / Off but-
ton for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
indicator light fl ashes three times.
When the status changes from inactive
to active, two bleeps are heard and the
indicator light fl ashes three times.
Automatic control active
If the air distribution adjustment dial and
the air fl ow adjustment dial are placed
in the “AUTO” position, or if the temper-
ature control dial is set to the minimum
temperature, the air conditioning sys-
tem is controlled automatically.
Automatic control active
If the air distribution adjustment dial
and the air fl ow adjustment dial are
placed in the “AUTO” position, the Air
intake / Interior air recirculation func-
tion is also controlled automatically.
Changing the status
Press the Air intake / Interior air recircu-
lation button for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
indicator light fl ashes three times.
When the status changes from inactive
to active, two bleeps are heard and the
indicator light fl ashes three times.
Automatic control inactive
Even if the air distribution adjustment
dial and the air fl ow adjustment dial are
placed in the “AUTO” position, the Air
intake / Interior air recirculation function
is no longer controlled automatically.
Automatic control inactive
The air conditioning system is no
longer controlled automatically.

D R I V I N G
VII
111
Switching to automated mode
Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position D .

“D” appears on the instrument panel
display.
The gearbox then operates in auto-ac-
tive mode, without any action on the
part of the driver.
It continuously selects the gear most
suited to the following parameters:
- driving style,
- road characteristics,
- vehicle load.
To optimise driving comfort and obtain
the most suitable gear, avoid sharp var-
iations in the pressure on the accelera-
tor pedal. “Auto sequential” mode
In the automated mode, you can
resume control temporarily at any time
using the steering wheel controls.
The use of these controls permits man-
ual selection of the gears in situations
which require a faster changedown
than that offered in automated mode
(arrival at a roundabout, exit from a car
park with a steep gradient, overtaking,
etc.).
The gearbox engages the gear re-
quested if the engine speed permits it.
The gear engaged appears.
To return to the automated mode, press
the back of the
“+/OFF” control for ap-
proximately 2 seconds.
Stopping the vehicle
Before switching off the engine, you
can:
- move to position N to leave the
gearbox in neutral.
- leave a gear engaged, such as fi rst or reverse.
In both cases, it is imperative that you
apply the handbrake to immobilise the
vehicle. Operating anomaly
With the ignition on, if the message

“Slow down” or
“Maintenance
required” appears on the multifunction
display, this indicates a gearbox mal-
function.
When a message is displayed, carry
out the following operations:
- slow down and stop your vehicle in a safe place,
- place the lever in position N and let
the engine run,
- open the bonnet to allow the engine to cool.
If the message disappears for a long
period, you can set off again.
If the message remains displayed or
appears frequently, contact a CITROËN
dealer without delay.
Take your foot off the accelerator pedal
gently to engage the gear.
At low speeds, when approaching a
stop or traffi c lights for example, the
gearbox changes down to fi rst gear au-
tomatically.

A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
157
GENERAL FUNCTIONS
Switching on Press the “PWR” button.
The last source selected
before switching off resumes
operation.
The audio equipment functions can be
used when the ignition switch is in the
“ON or “ACC” position.
Adjusting the volume Turn the “VOL” dial
respectively to the left to
decrease the volume or to
the right to increase it.
Switching off
Press the “PWR” button again. Setting the audio modes
Press the “SOUND” button
several times; the audio
modes change in the
following order:
SUB PUNCH / TYPE /
FIELD / BASS / MID /
TREBLE / FADER / BALANCE / OFF.
Quick access mode
To access the personalised sound
functions quickly, press and hold
this button, then turn it to reach the
personalised sound setting of your
choice.
Release the button to store the setting.
“Hold” mode
If you press this button for more than
2 seconds in the audio setting mode, the
system switches to “Hold” mode. The
audio mode selected will be retained
until you press this button again for
more than 2 seconds. Selecting the musical ambience
“TYPE”
Turn the “SOUND” dial; the
musical ambiences change
in the following order:
CLASSIC / JAZZ / POP /
ROCK / HIP-HOP.
Once the ambience has
been selected, press the “SOUND” but-
ton to confi rm.
“CLASSIC”: optimises the acoustics to
obtain perfect equalisation of the sound
for classical music.
“JAZZ”: optimises the acoustics to
obtain an ambient sound with speciifc
modulations in the bass, mid tone and
treble for jazz.
“POP”: optimises the acoustics to obtain
clear vocals and modulation of the bass
and treble for pop music.
“ROCK”: optimises the acoustics to
obtain a sound in harmony with the
rhythm which places the emphasis on
the mid tone for rock music.
“HIP-HOP”: optimises the acoustics
to obtain a powerful sound and
accentuation of the bass for hip-hop
music.
If the “TYPE” is changed, the sound
cuts out briefl y.
The audio setting mode is deactivated
when the radio is operated or a CD
is played or after approximately
10 seconds without any action.