reset Citroen C CROSSER DAG 2008 1.G Owner's Manual

I N S T R U M E N T S a n d C O N T R O L S
I
30
The total distance is
displayed in zone 1 of
the display and the trip
distance in zone 2 .
DISTANCE RECORDERS (A / B)
System for measuring the total distance
travelled by the vehicle during its
service life and the distance travelled in
a day or other period until it is reset to
zero by the driver.
Zero reset
With the ignition on, press the INFO

button for more than 2 seconds until
zeros appear. When the engine is
running, this indicates
the temperature of the
coolant.
COOLANT TEMPERATURE
If the bar is close to
the
critical position
located on the right, the
temperature is too high.
The symbol fl ashes when your engine
is overheating.

It is imperative that you stop your
vehicle safely.

Wait a few minutes before switching
off the engine.
Wait for the engine to cool
before topping up the level. The
cooling system is pressurised.
When the engine is
running , this indicates
the distance which can
still be travelled with the
fuel remaining in the tank
in relation to the average
consumption over the
last few miles/kilometres
travelled.
RANGE
When the range is less than 30 miles
(50 km) , dashes are displayed.
Fill the fuel tank as soon as possible.
The display of the range is updated.
As the cooling system is pressurised, to
avoid any risk of scalding, unscrew the
cap by two turns to allow the pressure
to drop.
When the pressure has dropped,
remove the cap and top up the level, if
necessary.
Consult a CITROËN dealer. This fi gure may increase following a
change in the style of driving or the
relief, resulting in a reduction in the
current consumption.
If you only add a few litres, the
value displayed will be incorrect.
Therefore, you must fi ll the tank
whenever possible.
When you disconnect
the battery, the previous
consumption data is lost and
the value displayed will be different
from that displayed before the battery
was disconnected. The distance
displayed must be considered an
approximate indication.

I N S T R U M E N T S a n d C O N T R O L S
I
31
SERVICE INDICATOR Resetting the service indicator
to zero
Your CITROËN dealer carries out this
operation after each service.
If you have carried out your vehicle’s
service yourself, the zero reset
procedure is the following:

 switch off the ignition,

 press the INFO button several times
in succession until the service indi-
cator is displayed.

 press and hold the INFO button for
a few seconds until the spanner
fl ashes .

 press the INFO button while the
spanner is fl ashing to change the
display “---” to “CLEAR” then the
time remaining before the next serv-
ice is due is displayed.
Service overdue
Operation
When the ignition is switched on, you
must press the INFO button several
times in succession until the service
indicator is displayed. The distance
recorder display line indicates the
number of miles (kilometres) remaining
and the time elapsed line indicates the
number of months remaining before the
next service is due.
After a certain distance and a
certain time, the displaying of “---”
is reinitialised and the display
indicates the time remaining before
the next service is due.
System which informs the driver when
the next service is due in accordance
with the manufacturer’s servicing
schedule.
The point at which the next service is
due is calculated from the last service
indicator zero reset.
It is determined by two parameters:
- the distance travelled (in miles
(km)),
- the time elapsed since the last serv- ice (in months).
The distance remaining to be travelled
may be weighted by the time factor,
depending on the user’s driving habits.
Example: the display indicates that
7300 miles (kilometres) remain before
the next service is due.
The symbol “---” remains displayed
until the fi rst service of a new vehicle
has been carried out.

Example: the display indicates that the
service is overdue. This service must
be carried out by a CITROËN dealer.
Each time the ignition is switched on,
the display
“SCHEDULED SERVICE”
is displayed for a few seconds to
indicate that the service must be carried
out without delay.

I N S T R U M E N T S a n d C O N T R O L S
I
32
System which provides current
information about the route travelled.
TRIP COMPUTER Average
consumption
(l/100km or km/l or
mpg)
This is the average
quantity of fuel consumed
since the last zero reset.
This fi gure may increase following a
change in the style of driving or the
relief resulting in a reduction in the
current consumption. Average speed
(km/h or mph)
This is the average
speed calculated since
the last zero reset. Resetting the information to
zero
Automatic
If the ignition remains in the “ACC”

(Accessories) position for at least
4 hours, the average consumption value
is reset to zero automatically.
If dashes “---” are displayed for long
periods in place of the digits while
driving, contact a CITROËN dealer. Current
consumption
(l/100km or km/l or
mpg)
This is the average
quantity of fuel
consumed during the
last few seconds of
driving.
Data displays
With the ignition on, press the
INFO
button on the fascia, to the left of the
instrument panel, several times in
succession to display the different
information:
- the average consumption,
- the average speed,
- the current consumption. When the required information is
displayed, press the
INFO button for
more than two seconds.
When the ignition is switched on, the
zero reset switches automatically from
manual mode to automatic mode.

I N S T R U M E N T S a n d C O N T R O L S
I
38
Set the time using the buttons as
indicated below:

 with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK button until the
time display fl ashes.
 Press the appropriate button to set
the time:

Button H: setting of the hour
The hours digits scroll when you press
this button.

Button M: setting of the minutes
The minutes digits scroll when you
press this button.

Button :00: resetting of the minutes to
zero.
- from 1 to 29 min
: rounded down to
the previous hour,
- from 30 to 59 min: rounded up to
the next hour.
Manual mode
Automatic mode
In this mode, setting is automatic using
the signal from the RDS radio stations.
 After setting the time, press the

DISP button; the time display stops
fl ashing.
The digital clock does not display
seconds.
When the “minutes” display is set or
reset to zero, the clock starts at the
zero second of the minute selected.
The time setting is lost if the battery
is disconnected.

 Turn button B “TUNE” to the left or
to the right to select “CT ON” (auto-
matic mode) or “CT OFF” (manual
mode).

 After selecting the mode, you can
exit the “Functions setting mode”
menu by pressing button B “TUNE”
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the “functions setting mode” menu
automatically.

D
C
D1D2D3
D4D5
D6D7D8
D7
D9D10D11D12
A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
204
Calendar, trip These double arrows permit
access to the driving information
screen, previous or next.
D - Consult the driving information:

D1 - the average speed,
D2 - the average consumption,

D3 - the current consumption,

D4 - for speed and consumption
graphs in 5 minute intervals,
D5 - choose an automatic reini- tialisation (key at off for more
than 4 hours) or manual
reinitialisation (press reset),

D6 - the distance which can still be
travelled (in relation to the fuel
remaining and the recent aver-
age consumption),
D7 - the distance travelled since the fuel tank was last fi lled (press
refuel to reinitialise),

D8 - the driving time (dura-
tion between the key being
turned to on then to off).
- press start to measure intermediate times with:

D9 - the duration,
D10 - the distance,
D11 - the speed,

D12 - the consumption.
C - Make a note on the calendar of
special days, birthdays, ...
Use the arrows to fi nd a date
and press directly on the day
required to enter the event.