instrument panel CITROEN C1 2017 User Guide

74
C1_en_Chap04_conduite_ed01-2016
There is an audible signal when the driver's door is   opened   and   the   vehicle   is   in   "ACC "
  mode.
If
  the   vehicle   is   not   immobilised,   the  
e

ngine   will   not   stop.
Switching off using the
electronic key
F Immobilise
  the   vehicle.
F  W ith   a   manual   gearbox:   put   the   gear   lever  
i

nto   neutral.
F
 
W
ith   an   ETG   gearbox:   place   the   gear  
s

elector at N .
F
 
W
ith   the   electronic   key   inside  
t

he vehicle, press the " S TA R T/
STOP "
  button.
The
  engine   stops.
The
  steering   locks   when   a   door   is   opened   or   on  
l

ocking   the   vehicle.
F

P
ress the "START/STOP " button
again
  to   change   to   "OFF "
  mode.
Emergency starting
When the electronic key is in the recognition   zone   and   your   vehicle  
d

oes   not   start   after   pressing   the  
"ST

ART/STOP "
  button,   this   warning  
l

amp   flashes   in   the   instrument   panel.
F
 
W

ith
 
a   manual   gearbox:   put   the   gear   lever  
i

nto
 
neutral.
F
 
W

ith
 
an   ETG   gearbox:   place   the   selector  
l

ever at N . F
 
P
ut   the   corner   of   the   electronic   key,   where  
t

he   indicator   lamp   is   located,   in   contact  
w

ith the "
START/STOP "   button.
 T

here   is   an   audible   signal   when   the  
e

lectronic   key   is   recognised;   the   vehicle  
c

hanges   to   "
ON "   mode.
F  
W
ith   a   manual   gearbox:   press   the   clutch  
p

edal   fully   down.
F  
W
ith   an   ETG   gearbox:   press   the   brake  
ped

al.
F  
C
heck   that   the   "Keyless   Entry   and  S
tarting"   indicator   lamp   comes   on   in   green  i
n   the   instrument   panel.
F

P
ress the "START/STOP "
  button.
 T

he   engine   starts.
If
  the   engine   does   not   start,   contact   a  
C

ITROËN   dealer   or   a   qualified   workshop.
Driving

77
C1_en_Chap04_conduite_ed01-2016
Gear selector
ETG electronic gearbox
The five-speed ETG electronic gearbox offers a choice between the ease of automated operation o r the pleasure of manual gear changing.
R.
 R
everse:   with   your   foot   on   the   brake   pedal,  
m

ove   the   gear   selector   to   the   right   then  
f

or ward   to   select   this   position.
N.
 N

eutral:   with   your   foot   on   the   brake   pedal,  
s

elect   this   position   to   start   the   engine.
E.
 
A
utomatic   (Easy)   mode:   move   the   gear  
s

elector   back   to   select   this   mode.
M.
 M

anual   mode   with   sequential   gear  
c

hanging:   move   the   gear   selector   back  
t

hen   to   the   left   to   select   this   mode.Press
  behind   the   "+"
 s
teering
 m

ounted   control   paddle   to   change   up.
Steering mounted control paddles
The position of the gear selector (R , N, E or M )  i
s   displayed   in   the   instrument   panel.
In
  automatic   (Easy)   mode,   when   you  
t

emporarily   take   control   of   gear   changing,  
t

he   gear   engaged   is   also   displayed   in   the  
in

strument
 pan
el.
Display in the instrument panel
Press behind the "-"  steering  m
ounted   control   paddle   to   change  
d

own.
The
  steering   mounted   control   paddles  
c

annot   be   used   to   select   neutral   or   to  
e

ngage   or   come   out   of   reverse   gear.
4
Driving

80
C1_en_Chap04_conduite_ed01-2016
The vehicle can be stopped whatever the position   of   the   gear   selector   (N , E or R ).
However,
  there   is   an   audible   signal   on   opening  
t

he   driver's   door   if   the   gear   selector   is   not   at  
p

osition N .
Switching off
When the vehicle is stopped with the e
ngine   running,   always   put   the   gear  
s

elector to neutral N .
There
  is   a   continuous   audible   signal  
i

f   you   turn   the   ignition   switch   to   "OFF "
with
  the   vehicle   in   2
nd, 3rd, 4th or 5th ge a r.
In
 
this
 
case
 
return
 
the
 
ignition
 
switch  
t

o " ON ",
 
move
 
the
 
gear
 
selector
 
to  
p

osition


N , then to position E , M or R,
then
 
turn
 
the
 
ignition
 
switch
 
to
 
" OFF ".
On
 
a
 
slope,
 
use
 
the
 
brakes
 
to
 
i

mmobilise
 
the
 
vehicle
 
and
 
place
 
the  
g

ear
 
selector
 
in
 
position
 
N , E or R . With
  the   ignition   on,   illumination  
o

f   this   warning   lamp   indicates   a  
g

earbox   fault.
Contact   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Operating faults
In all cases, it is essential
that you
apply the parking brake  to   immobilise  
t

he   vehicle.
Before
  doing   anything   under   the  
b

onnet,   check   that   the   gear   selector   is  
i

n neutral N   and   the   parking   brake   is  
a

pplied.
Limits of operation
On a gradient, or when hill start assist is activated, n ever hold the vehicle using the
accelerator :
  you   could   damage   the   clutch.
In
  these   situations   there   is   an   audible   signal.
F
 
M
ove   the   gear   selector   to   position   N.
F
 
W
ait   15   minutes   to   allow   the   clutch   to   cool  
d

own   before   setting   off. -
 
c
heck   that   the   ignition   switch   is   at   the  
"
O
N
"

position,
-  
p
lace   the   gear   selector   at   N
,   then   move   it  
t

o E
, M or R .
If 1   is   flashing   in   the   instrument   panel:
-  p lace   the   gear   selector   at   E or M
, then
move   it   to   N.
If R
  is   flashing   in   the   instrument   panel:
-
 
p
lace   the   gear   selector   at   R,
  then   move   it  
t

o N.
If
N is   flashing   in   the   instrument   panel
 a

ccompanied   by   an   audible   signal   for   a   long   time:
Driving

83
C1_en_Chap04_conduite_ed01-2016
Stop & Start (VTi 68 S&S engine)
Operation
Going into engine STOP
mode
This indicator lamp comes on in the instrument   panel   and   the   engine  
g

oes   into   standby   automatically:
-
 
w

hen
  stationary,   in   neutral,   and   you  
r

elease   the   clutch   pedal.
Never
  refuel   with   the   engine   in  
S

TOP mode;   you   must   switch   off   the  
i

gnition   with   the   button.
For
  smoother   operation,   during  p
arking   manoeuvres   STOP   mode   is  n
ot   available   for   a   few   seconds   after  
c

oming   out   of   reverse   gear.
The
  Stop   &   Start   does   not   affect   the  
v

ehicle's   systems,   such   as   for   example,  
b

raking,   power   steering...
The
 
Stop
 
&
 
Start system
 
puts
 
the
 
engine
 
t

emporarily
 
into
 
standby
 
-
 
STOP
 
mode
 
-
 
during
 
s

tops
 
in
 
the
 
traffic
 
(red
 
lights,
 
traffic
 
jams,
 
or
 o
ther...).
 
The
 
engine
 
restarts
 
automatically
 
-
 S
TART
 
mode
 
-
 
as
 
soon
 
as
 
you
 
want
 
to
 
move
 
o

ff.
 
The
 
restart
 
takes
 
place
 
instantly,
 
quickly
 
a

nd
 
silently.
Per fect
 
for
 
urban
 
use,
 
the
 
Stop
 
&
 
Start
 
system
 
r

educes
 
fuel
 
consumption
 
and
 
exhaust
 
e

missions
 
as
 
well
 
as
 
the
 
noise
 
level
 
when
 
s

tationary.
Stop & Start time counters
A partial time counter counts the periods in S TOP   mode   during   a   journey.
It
  is   displayed   in   the   trip   computer   once   the  
S

top   &   Start   is   operating.
Press one of the " DISP" buttons to return to the
previous
 d

isplay.
A
  global   time   counter   counts   the   periods   in  
S

TOP   mode   since   the   last   reset.
When
  it   is   displayed,   press   one   of   the  
"D

ISP " buttons
  to   reset   the   counter.
4
Driving

85
C1_en_Chap04_conduite_ed01-2016
At any time, press this button to deactivate the system.
Manual deactivation /
reactivation
If the system has been deactivated in S TOP mode,   the   engine   restarts   immediately.
The
  system   is   reactivated   automatically   at  
e

very   new   engine   start   by   the   driver.
Press
  this   button   again.
The
  system   is   active   again;   this   is   confirmed   by   the
 i

ndicator   lamp   going   off   in   the   instrument   panel.
Deactivation
  is   confirmed   by   the  
i

llumination   of   this   indicator   lamp   in  
t

he   instrument   panel.
Before
 
doing
 
anything
 
under
 
the
 
b

onnet,
 
deactivate
 
the
 
Stop
 
&
 
Start
 
s

ystem
 
to
 
avoid
 
any
 
risk
 
of
 
injury
 
r

esulting
 
from
 
automatic
 
operation
 
of
 
S

TART
 
mode.
Maintenance
The Stop & Start system requires a 12 V b
attery   of   a   special   specification   and  
t

echnology.
All
  work   on   this   type   of   battery   must   be  
d

one   only   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
For
  more   information   on   the   12   V  
b

attery,   refer   to   the   corresponding  
s

ection.
4
Driving

86
C1_en_Chap04_conduite_ed01-2016
The speed limiter cannot, in any circumstances,   replace   the   need   to o

bserve   speed   limits,   nor   can   it   replace   the
 n

eed   for   vigilance   on   the   part   of   the   driver.
Speed limiter (PureTech 82 engine)
The speed limiter is switched on  manually: t
his   can   be   done   whatever   the   speed   of   the  
v

ehicle.   However,   if   you   are   driving   at   less   than  
2

0   mph   (30   km/h),   the   programmed   speed   will  
b

e   fixed   at   20   mph   (30   km/h).
The
  speed   limiter   is   paused by operation of the
control.
The
  programmed   speed   can   be   exceeded  
t

emporarily   by   pressing   the   accelerator   firmly  
b

eyond   the   point   of   resistance.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal   until   the   vehicle  
r

eturns   to   the   programmed   speed   limit.
System
  which   prevents   the   vehicle   from   exceeding   the   speed   programmed   by   the   driver.Steering mounted controls
The controls are grouped together on this c
ontrol   stalk   at   the   steering   wheel.
1.
 S

peed   limiter   on   /   off:   by   pressing   the   end  
o

f   the   control   stalk.
2.
 D

ecrease   the   setting:   by   pushing   the  
c

ontrol   stalk   down.
3.
 I

ncrease   the   setting:   by   pushing   the   control  
s

talk   up.
4.
 S

peed   limiter   on   /   pause:   by   pulling   the  
c

ontrol   stalk   towards   you.
Displays in the instrument panel
The information is grouped together in the instrument   panel   screen.
5.
 S

peed   limiter   mode   selection   indication.
6.
 S

peed   limiter   on   /   pause   indication.
7.
 S

peed   value   setting.
The
 
programmed
 
speed
 
remains
 
in
 
the
 m

emory
 
when
 
the
 
ignition
 
is
 
switched
 
off.
Driving

88
C1_en_Chap04_conduite_ed01-2016
Switching off
F Press  the   end   of   the   control   stalk. T
he   display   of   information   related   to   the  
sp

eed
 l
imiter
 d
isappears.
Operating fault
Illumination of this warning lamp in the   instrument   panel   indicates   a   fault  
w

ith   the   speed   limiter.
Have
  it   checked   by   a   CITROËN  
d

ealer   or   a   qualified   workshop.
The
  use   of   mats   not   approved   by  
C

ITROËN   may   inter fere   with   the  
o

peration   of   the   speed   limiter.
To
 
avoid   any   risk   of   jamming   of   the  
ped

als:
-
 
e
nsure   that   the   mat   is   secured  
c

o r r e c t l y,
-
 
d
o   not   fit   one   mat   on   top   of   another.
Temporarily exceeding the
programmed speed
F Press f irmly  on   the   accelerator   pedal,  g
oing   beyond   the   point of resistance, to
exceed
  the   programmed   speed   limit.
The
  speed   limiter   is   deactivated   temporarily  
a

nd   the   displayed   programmed   speed   flashes.
As
  soon   as   the   vehicle's   speed   returns   to   the  
p

rogrammed   value,   the   limiter   operates   again:  
t

he   display   of   the   programmed   speed   becomes  
s

teady   again.
An
  audible   signal   accompanies   the  
f

lashing   of   the   programmed   speed  
w

hen   exceeding   the   speed   is   not   due   to  
a

n   action   by   the   driver   (steep   hill...).
Driving

89
C1_en_Chap04_conduite_ed01-2016
Speed limiter (VTi 68 engine)
System which prevents the vehicle from exceeding the speed programmed by the driver.
T he   speed   limiter   is   switched on
 m
anually:
 t

his   can   be   done   whatever   the   speed   of   the  
v

ehicle.   However,   if   you   are   driving   at   less   than  
2

0   mph   (30   km/h),   the   programmed   speed   will  
b

e   fixed   at   20   mph   (30   km/h).
The
  speed   limiter   is   paused by operation of the
control.
The
  programmed   speed   can   be   exceeded  
t

emporarily   by   pressing   the   accelerator   firmly  
b

eyond   the   point   of   resistance.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal   until   the   vehicle  
r

eturns   to   the   programmed   speed   limit.
The
  programmed   limit   speed   is   erased  
w

hen   switching   off   the   ignition.
Steering mounted controls
The controls are grouped together on this control   stalk   at   the   steering   wheel.
1.
 S

peed   limiter   on   /   off:   by   pressing   the   end  
o

f   the   control   stalk.
2.
 P

rogramming   the   speed
 D

ecrease   the   setting:   by   pushing   the  
c

ontrol   stalk   down.
3.
 R

estore   speed   limiter
 I

ncrease   the   setting:   by   pushing   the   control  
s

talk   up.
4.
 P

ause   speed   limiter:   by   pulling   the   control  
s

talk   towards   you.
Displays in the instrument panel
The information is grouped together in the instrument   panel   screen.
5.
 S

peed   limiter   on   /   pause   indication.
6.
 S

peed   value   setting.
The speed limiter cannot, in any circumstances,   replace   the   need   to   observe s

peed   limits,   nor   can   it   replace   the   need   for
 v

igilance   on   the   part   of   the   driver.
If you choose to display other information (trip  A
  for   example),   the   speed   limiter  
i

nformation   is   automatically   displayed   again  
a

fter   about   6   seconds.
4
Driving

91
C1_en_Chap04_conduite_ed01-2016
Switching off
F Press  the   end   of   the   control   stalk T
he   display   of   information   related   to   the  
sp

eed
 l
imiter
 d
isappears.
Operating fault
Illumination of this warning lamp in the   instrument   panel   indicates   a   fault  
w

ith   the   speed   limiter.
The
  use   of   mats   not   approved   by  
C

ITROËN   may   inter fere   with   the  
o

peration   of   the   speed   limiter.
To
 
avoid   any   risk   of   jamming   of   the  
ped

als:
-
 
e
nsure   that   the   mat   is   secured  
c

o r r e c t l y,
-
 
d
o   not   fit   one   mat   on   top   of   another.
Temporarily exceeding the
programmed speed
F Press f irmly  on   the   accelerator   pedal,  g
oing   beyond   the   point of resistance,
to
exceed
  the   programmed   speed   limit.
The
  speed   limiter   is   deactivated   temporarily  
a

nd   the   displayed   programmed   speed   flashes.Have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
An
  audible   signal   accompanies   the  
f

lashing   of   the   programmed   speed  
w

hen   exceeding   the   speed   is   not   due   to  
a

n   action   by   the   driver   (steep   hill...).
As
  soon   as   the   vehicle's   speed   returns   to   the  
p

rogrammed   value,   the   limiter   operates   again:  
t

he   display   of   the   programmed   speed   becomes  
s

teady   again.
4
Driving

93
C1_en_Chap04_conduite_ed01-2016
Lane departure warning system
System which detects the unintended crossing of longitudinal traffic lane markings on the ground, using a camera that recognises both solid and broken   lines.
To
  improve   your   safety,   the   camera   analyses   the   image   and   then   triggers   a   warning   if   the   vehicle   wanders   over   a   lane   marking   (speed   higher   than  
3

0 mph   (50   km/h)).
This
  system   is   particularly   suitable   for   motor ways   and   dual   carriageways.
The
  lane   departure   warning   system  
c

annot   in   any   circumstances   replace  
t

he   need   for   vigilance   on   the   part   of   the  
d

river.
It
  is   necessary   to   observe   driving  
r

egulations   and   take   a   break   every  
two
  hours.
Activation
F Press  this   button,   located   on   the   steering  w
heel.
Detection
You are alerted by an audible signal and the display   of   a   warning   lamp   in   the   instrument   panel.
No
  alert   is   given   if   the   direction  
i

ndicators   are   on   and   for   around  
20
  seconds   after   they   stop   flashing.
The
 
s

ystem
 
s

hould
 
b

e
 
d

eactivated
 
w

hen
 
d

riving
 
with
 
snow
 
chains
 
or
 
the
 
spare
 
w

heel
 
fitted.
4
Driving