wheel Citroen C3 PLURIEL 2004 1.G Repair Manual

Downloaded from www.Manualslib.com manuals search engine 222
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: RHY RHZ N° RPO 9128 #
Reposition the timimg belt, belt at «a»well tensioned, in the following order:
Fuel high pressure pump pulley
(21).
Guide roller
(15).
Crankshaft pinion
(19).
Coolant pump pinion
(16).
Tensioner roller
(18).
Position tool
[1]on the belt at «a».
Remove tools
[4]and [9].
Turn the tensioner roller
(18)anticlockwise, using tool [2], to attain an overtension of:
98 ± 2 SEEM units.
Tighten screw
(17)of the tensioner roller to 2,5 ± 0,2 m.da N.
Lock the flywheel by means of tool
[6].
Tighten the accessories drive pulley screw
(8)to 7 ± 0,7 m.da N.
Remove tools
[1], [3], [5] and [6].
Rotate the crankshaft eight times in the normal direction of rotation.
Peg:
The crankshaft, using tool
[3].
The camshaft drive pulley, using tool
[5].
B1EP1ABDB1EP1ACC
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 223
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: RHY RHZ N° RPO 9128 #
Lock the engine flywheel, using tool [6].
Slacken:
The accessories drive pulley
(8).
The screw (17) of the tensioner roller (18).
Fit the tool [1].
Turn the tensioner roller, using tool [2], to attain a tension of:54 ± 2 SEEM units.
Tighten screw (17)of the tensioner roller (18)to 2,5 ± 0,2 m.daN.
Remove tool [1].
Fit tool [1].
The tension value should be:
54 ±3 SEEM units.ESSENTIAL: If the value is incorrect, recommence the operation.
Remove tools [1], [3], [5]and [6].
Rotate the crankshaft two times in the normal direction of rotation.
Peg:
The crankshaft, using tool
[3].
The camshaft drive pulley.
IMPERATIVE:If the pegging is not possible, recommence the operation.
B1EP1ACC
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 253
INJECTION
XSARACHECKING AND SETTING THE DELPHI MECHANICAL INJECTION PUMP
Tools.
[1]
Flywheel locating peg: 7014T.J
[2] H M8 screw: ().0188.E Tool kit C.0188
[3]Injection pump setting peg Ø 6 mm : ().0188.H
After carrying out the necessary dismantling operations on the vehicle, proceed in the following manner:
Remove:
The screws
(6), (7), (9), (10)and (12).
The upper casing (8).
The intermediate casing (11).
WARNING:Refit the screw (6)equipped with a washer.(Thickness 5 mm)
Turn the front RH wheel to turn the engine.(Normal direction of rotation) Bring the camshaft and injection pump pulleys to their setting point.
Position the flywheel peg, using tool [1].(From below the vehicle) Turn the engine until the peg [1]engages in the flywheel.
B1EP12NC
Engine: WJY
B1BP1S9C

Downloaded from www.Manualslib.com manuals search engine 286
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engines: HFX – KFV – KFU – NFU – 8HX – 8HW – 8HV – 8HY
NOTE:All the clutches are «push»type with hydraulic control.
Description.The declutch control has a declutch fork mounted on a balljoint.(1)The balljoint is screwed into the clutch casing.(2)Declutch fork.(3)Clutch casing.(4)Bearing.(5)Clutch plate.
The clutch control slave cylinder
(7)is fixed by two screws (6)onto the exterior of the clutch casing.
Tightening torques (m.daN).
Fixing of clutch plate / engine flywheel: 2 ± 0,2 Fixing of clutch control slave cylinder / clutch housing:2 ±0,25 Fixing of engine flywheel / crankshaft
Pretightening:1,7 ± 0,1Angular tightening:70° ± 5°
B2BP047CB2BP04QC
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 287
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engines: KFW NFU NFV 6FZ RFN RFS 8HZ 9HZ 9HY WJY RHY RHZ
NOTE:All the clutches are «push»type with hydraulic control.
Description.The declutch control has a declutch fork mounted on a balljoint.(1)The balljoint is screwed into the clutch casing.(2) Declutch fork.(3) Clutch casing.(4) Bearing.(5) Clutch plate.
The clutch control slave cylinder
(7) is fixed by two screws (6)onto the exterior of the clutch casing.
Tightening torques (m.daN).
Fixing of clutch plate / engine flywheel: 2 ± 0,2 Fixing of clutch control slave cylinder / clutch housing:2 ±0,25 Fixing of engine flywheel / crankshaft
Pretightening:1,75 ± 0,1Angular tightening:75° ± 5°: 6,3 ± 2,2
B2BP047CB2BP05SC
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 301
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX
Engines: HFX KFV NFU 8HX 8HW
(1)Retaining clip.(2)Secondary shaft.(3)Drive pinion (5th gear).(4) Bearing retaining clip screw.(5)Gearbox casing.(6)Intermediate plate.(7)Gearbox casing fixing screw.(8)Clutch bearing guide screw.(9) Clutch housing.(10)Bearing guide.(11)Primary shaft.(12)Differential housing.(13)Speedometer screw.(14)Counter drive.(15)Planet pinions.(16) Satellite pinions.(17)Differential gearwheel.(18)Driven pinion (1st gear).(19)1st / 2nd gear synchroniser and reverse gear driven pinion.(20)Driven pinion (2nd gear).(21) Driven pinion (3rd gear).(22) 3rd / 4th gear synchroniser.B2CP3SRP
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 305
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX
Engines: KFW NFU
(1)Primary shaft.(2)Clutch bearing guide.(3)Clutch housing.(4) Gearbox casing.(5) Intermediate plate.(6)Bearing retaining clip.(7) Drive pinion (5th gear).(8) Secondary shaft.(9)5th gear synchroniser.(10)Driven pinion (5th gear).(11)Driven pinion (4th gear).(12)3rd / 4th gear synchroniser.(13)Driven pinion (3rd gear).(14)Driven pinion (2nd gear).(15) 1st / 2nd gear synchroniser and reverse gear driven pinion.(16) Driven pinions (1st gear).(17)Differential gearwheel.(18)Satellite pinions.(19)Planet pinions.(20)Counter drive.(21)Speedometer screw.(22) Differential housing.B2CP167P
XSARA

Downloaded from www.Manualslib.com manuals search engine 313
CLUTCH
GEARBOX
TRANSMISSION
MA/5 PILOTED MANUAL GEARBOX
Engines: KFV 8HX
(1)Circlip.(2) Secondary shaft.(3) Drive pinion (5th gear).(4)Bearing stop screw.(5) Gearbox casing.(6)Intermediate plate.(7) Gearbox casing fixing screw.(8)Clutch bearing guide screw.(9)Clutch housing.(10)Bearing guide.(11)Primary shaft.(12)Differential housing.(13)Speedometer screw.(14)Counter drive.(15) Planet pinions.(16)Satellite pinions.(17) Differential gearwheel.(18)Driven pinion (1st gear).(19)1st / 2nd gear synchroniser and reverse gear driven pinion.(20)Driven pinion (2nd gear).(21)Driven pinion (3rd gear).(22)3rd and 4th gear synchroniser.B2CP3SRP
C2

Downloaded from www.Manualslib.com manuals search engine 320
CLUTCH
GEARBOX
TRANSMISSION
BE4/5 GEARBOX
Engines: 6FZ RFN RFS WJY 8HV 8HY 8HZ 9HZ 9HY RHY RHZ
Tightening torques (m.daN).
(23)
Clutch bearing guide (3 screws): 1,25 ± 0,2
(24)
Clutch housing (13 screws): 1,3 ± 0,2
(25)
Primary shaft nut (1 screw):7,25 ± 0,5
(26)
Secondary shaft nut (1 screw): 6,5 ± 0,5
(27)
Yoke retaining screw (2 screws): 1,5 ± 0,2
(28)
Differential gearwheel screw (2 screws): 6,5 ± 0,5
Reverse gear switch (1 screw): 2,5 ± 0,3
(29)
Differential housing (4 screws): 5 ± 0,5
(30)
Breather pipe:1,7 ± 0,2
(31)
Rear housing cover screws (7 screws):1,25 ±0,2
(32)
Topup plug (1 screw):2,2 ±0,2
(33)
Differential housing screws (4 screws):1,25 ±0,2
(34)
Drain plug (1 screw):3,5 ±0,3
B2CP3BRD
C3 XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 354
CLUTCH
GEARBOX
TRANSMISSION
DRIVESHAFTS GEARBOX
Tightening torques (m.daN)
Driveshaft
bearing Engines
V ehiclesGearboxRH side LH side Tool kitGearbox oil seal mandrels
24,5 ± 0,5
32 ± 1,5
32,5 ± 2,57114T.W
Seal extractor
RH / LH
() 0338 C
() 0338 J1
+ () 0338 J3() 0338 H1
+ () 0338 H2
() 0338 J1
+ () 0338 J2() 0338 H1
+ () 0338 H2() 0338 7114T.X
7116T Driveshaft
nut
HFX KFV KFU
8HX 8HW
NFU
KFW NFU
NFV RFS RFN 6FZ WJY
8HZ 9HZ 9HY RHY RHZ
8HV 8HY
NFU RFN RHZ
KFV MA/5
XSARA
XSARA PICASSOC2 C3 C3 Pluriel
XSARANO
2 ± 0,2
1,8 ± 0,1
2 ±0,2
1,8 ±0,1
1 ±0,1
C3
C3
XSARA PICASSO
XSARA
Tightening torque (m.daN) for wheel bolts: XSARA = 8,5 ± 0,8 XSARA PICASSO = 10 ± 1 C2 C3 C3 PLURIEL = 9 ± 1BE4/5
AL 4
C2 C3 C3 PLURIEL XSARA XSARA PICASSO