change wheel Citroen C4 PICASSO 2008 1.G Owner's Manual

–+
60
II
To select manual mode :
- Move the selector to po-sition M.
Controls under the steering wheel
The levers under the steering wheel give you access to all the six forward gears.
To change gear :
- Pull the lever “+” to change up a gear.
- Pull the lever “-” to change down a gear.
Note : The levers do not permit you to select neutral or reverse gear, or to exit reverse gear.
In situations of high engine speeds (heavy acceleration), a change up will not occur unless the driver ac-tions this on the lever controls.
( 6 - S P E E D ) E L E C T R O N I C G E A R B O X S Y S T E MM A N U A L M O D E( 6 - S P E E D ) E L E C T R O N I C G E A R B O X S Y S T E M( 6 - S P E E D ) E L E C T R O N I C G E A R B O X S Y S T E M
Observations :
- If the vehicle stops or reduces speed (for example when ap-proaching a stop sign), the gear-box changes down automatically to fi rst gear.
- In manual mode, it is not neces-sary to release the accelerator completely during gear changes.
- A request to change gear is ac-cepted only if the engine speed permits it.
- For safety reasons, depending on the engine speed, a change down may be performed auto-matically.

78
II
Direction indicators
Left : downwards.
Right : upwards.
For a change of direction, operate the control stalk to go beyond the “tight spot”. It will revert automati-cally to its initial position with the return of the steering wheel.
Headlamp fl ash
Pull the control stalk towards you.
The headlamp fl ash is possible even with the ignition switched off.
Horn
Press at the lower part of the fi xed centred controls steering wheel.
Emergency activation of the hazard warning lamps
A heavy deceleration of the vehi-cle will cause the hazard lamps to activate automatically.
They will cease automatically on reacceleration of the vehicle or manually if you press on the hazard lamps button on the dashboard.
Driving with the hazard lamps activated renders the direction indicators inoperational.
Distress signal
The distress signal operates all the direction indicators simultaneously.
Only make use of this in a situa-tion of danger, for an emergency stop or if you fi nd yourself driving in exceptional weather conditions.
The distress signal will operate even with the ignition switched off.
S I G N A L L I N G
Sound signal for vehicle lamps left on
With the ignition switched off, the signal will activate when the driv-er’s door is opened, to indicate that lamps have been left on.
It will cease when the door is closed, the lamps switched off, or the ignition switched on again.
This signal is inactive if the auto-matic lighting of headlamps and /or the guide-me-home lighting are activated.

154
IV
Multifunction screen A
Technical specifi cations
Your Bluetooth compatible radio possesses :
-3 wavebands (MW/LW/FM).
-Dual tuner with RDS EON PTY, display of the PS name, RDS programme search, TA traffi c informa-tion, 24 pre-selections (18 FM - 6 MW/LW), automatic memorisation of the AST strongest stations.
-An MP3- compatible CD reader.
-Audio power of 4 x 35 W.
Multifunction screen C
C O N T R O L S A T T H E S T E E R I N G W H E E L
The controls at the steering wheel give you access to certain functions, without you needing to use the radio-CD control panel.
1VOL +Volume increase
2
Radio source :Short press : Automatic search of higher frequencies.CD and CD changer source :Short press : Forward search for tracks.Long press : Fast forward with accelerated sound.
3
Radio source :Scrolling of pre-set stations.CD and MP3 source :Search of the track.CD changer source :Selection of next or previous CD.
4VOL -Volume decrease.
5MuteFirst press : Temporary sound pause.Second press : Restoration of sound.
6MENU
Access to the main menu to activate/deactivate or choose the adjustments for your vehicle.In certain countries, this control is deactivated while the vehicle is moving.
7OK
In a menu, a list, an alphabet :Validation of the function, the element or the value chosen.If your vehicle has the Bluetooth system : Answer call, end call
8Selection of the next or previous elements of a menu in a screen, a list, an alphabet.
9ESCShort press : Cancellation of the current operation.Long press : Return to the permanent display.
10MODESelection of type of information displayed on the right of the screen and, for screen A, choice of activation/deactivation of functions and adjustments.
11If your vehicle has the Bluetooth system : Press : Display of the “Directory” menu.
12If your vehicle has the Bluetooth system :Press : Activation of voice recognition.

155
G E N E R A L F U N C T I O N S -
A U D I O A D J U S T M E N T S
On / Off
With the key in Drive position M, press on control A to switch the radio on or off.
Note :
- If the radio was on the last time you switched off the ignition, it will resume automatically when you switch on the ignition again. You will not have to press on control A.
- After switching off the ignition, you can still operate the audio system even without the ignition key be-ing present. Simply press on but-ton A. The system will turn itself off after approx.30minutes.
Anti-theft system
This radio is coded in such a way as to function only on your particu-lar vehicle. It would be unusable if installed on any other vehicle.
Note :
The anti-theft system is automatic and requires no action on your part.
Selection of source
To select either Radio, CD (CD already inserted and Radio source activated), or CD changer source, press on control D.
When you insert a CD it automati-cally starts being read.
Note :
When the radio is switched off, the source selected is memorised.
Volume adjustment
Rotate control A to increase or de-crease the sound volume.
You can also increase or decrease the volume using buttons 1 and 4at the steering wheel.
Note :
- The sound volume when you switch off the radio will be the same when you switch it on again.
- The radio sound volume auto-matically adjusts to the vehicle speed, provided the “volume ad-justment” function is activated.
Temporary sound pause
Press on control 5 at the steering wheel, or on the MUTE button, to activate this function.
The sound will be paused, regard-less of the source selected.
To restore the audio output, press one of the controls at the steering wheel.
Sound adjustments
Each press on button F brings up the parameter to be adjusted :choice of predefi ned sound am-biances, bass, treble, loudness, fade (front/rear sound distribu-tion), balance (left/right sound dis-tribution) and volume adjusted to vehicle speed.
Press buttons K or N to modify the values for the function displayed.
Note :
- The selection of a sound am-biance automatically adjusts bass and treble. These can be modifi ed. To restore the original adjustments for the musical am-biances, reset bass and treble to zero.
- Adjustment of loudness, as well as bass and treble when they are available, are specifi c to each sound source and to each musical ambiance.
- If you leave the audio system un-actioned for a few seconds, it will revert to the normal display.

IV
Selecting CD source
After inserting a CD, with the printed side facing upwards, the player will start playing the CD automatically.To change manually to CD source (CD already inserted), press but-ton D until you obtain the source you require.
Ejecting a CD
Press button B to eject the CD, the audio system will automati-cally switch to radio source.
If the CD is not removed within 10 to 15 seconds of being ejected, it will automatically be taken back into the CD player, although it will not be played.
Selecting a track
Press button K once to play the next track.
Press button N once to return to the beginning of the track current-ly being played, press a second time to go back to the start of the previous track.
Press the buttons successively to skip several tracks at a time.
This can also be done via the con-trol G. As the list of tracks is dis-played on the screen, select the desired track using buttons J or M, then validate using button L.
You can also do this by means of control 2 at the steering wheel.
Fast forward and rewind with accelerated sound
To move swiftly through the CD, press and keep pressed button Kor N, respectively for fast forward or rewind with accelerated sound.
Play resumes as normal when the button is released.
Menu
This menu allows activation/deac-tivation of two options :
- Playback of the fi rst 7 seconds (approx.) of each track of the CD.
- Random playback of the CD tracks.
This can be accessed in two ways :
- Either by pressing button O and proceeding as for Search of Sta-tions RDS – for screen C, the sub-menu corresponds to the Audio Preferences.
- Or, provided you are in CD source, by pressing onbutton L. You can then access the Audio menu (for screen C only).
Note :
If one of these options is active, it remains active for CD changer source.
Safety precautions
For safety, do not use a CD player if the cabin temperature is higher than +60 °C or lower than -10° C.
If the temperature becomes too high, an automatic safety device will prevent the CD player from working until an acceptable tem-perature is restored.
Handling compact discs
Do not drop them. Store the CDs so that they are kept of dust. Avoid touching the disc surface as any scratches may adversely affect the sound quality. Do not attach any stickers to the discs. Do not use damaged or deformed discs. Do not expose them to heat or di-rect sunlight.
If the surface of the compact disc is dirty, it can be wiped with a soft, clean cloth. Always wipe from the centre of the disc outwards.
C D S O U R C E

IV
C D C H A N G E R S O U R C E
Selecting a CD
To select a CD, either press one of the pre-selection buttons 1 to 5 on the keypad P, or scroll using but-tons J or M.
The CD will start to play automati-cally.
You can also do this by means of control 3 at the steering wheel.
After each change of source, on return to CD changer source, play-back will resume at the same point where it had been interrupted.
Selecting a track
Press button K once to play the next track.
Press button N once to return to the beginning of the track current-ly being played, press a second time to go back to the start of the previous track.
Press the buttons successively to skip several tracks at a time.
You can also do this by means of the controls 2 and 3 at the steer-ing wheel.
Fast forward and rewind with accelerated sound
Press and keep pressed one of the buttons K or N respectively for fast forward or rewind with accelerated sound. Play resumes as normal when the button is released.
Menu
This menu is for activation/deacti-vation of three options :
- Playback of the fi rst 7 seconds (approx.) of each track of the CD.
- Repetition of the current CD.
- Random playback of tracks, CD by CD.
This can be accessed in two ways :
- Either by pressing button O and proceeding as for Search of Sta-tions RDS – for screen C, the sub-menu corresponds to the Audio Preferences.
- Or if you are in CD changer source by pressing button L. You then have access to the AUDIO menu (for screen C only).
Note:
If one of these options is active, it remains active for CD source.
CD Changer
This equipment S (if present) is lo-cated in the passenger’s storage compartment on the dashboard. It can accommodate 5 discs.
Inserting CDs into the magazine
Insert the CDs printed surface to the left.
Note :
- Each compartment takes one disc only.
- The CD changer will not operate if discs are inserted the wrong way up.
Removing discs
To remove a CD, give a long press on the corresponding button.
Note :
- The CD changer (if there is one) is not MP3 compatible.
Selecting CD changer source
Press on button D until you reach CD changer.
After the magazine engages, play-back of the fi rst track of the fi rst CD will begin.

A
1
VI
193
C H A N G I N G A W H E E L
REMOVING A WHEEL
1. Park the vehicle on level, sta-ble and non-slippery ground. Apply the parking brake.
Switch off the ignition, check that the parking brake is ap-plied (message and warning lamp in the instrument panel) and engage fi rst gear or re-verse gear depending on the slope (P if an automatic gear-box, D or R if a 6-speed elec-tronic gearbox).
2. Use a chock to secure the ve-hicle more safely. Place the chock in front of the wheel that is opposite the wheel affected.
3. Detach the trim using the re-moving tool 4, pulling in the area of the valve.
For vehicles with alloy wheels, insert the trim removing tool 1into the recess in the central trim and lever it off.
For vehicles with alloy wheels that have visible bolts, remove the chromes covers using the tool 2.
Before any operation of this sort, it is advisable to deactivate your pneumatic suspension (see “Pneumatic sus-pension”). When changing a wheel, it is essential to immobil ise the vehicle on ground that is level, stable and non-slippery.
4. Slacken the wheel bolts. For vehicles with alloy wheels, undo the anti-theft bolts using tool 9.
5. Position the jack under the vehicle (see diagrams), at the jacking point A closest to the wheel to be changed.
6. Unwind the jack 5 until its bracket is in contact with the ground. Make sure that the jack is vertical under the jack-ing point used.
7. Continue to extend the jack so as to raise the vehicle.
8. Undo the wheel bolts and re-move the wheel.

VI
195
Any repair or any change of tyre, on a wheel fi tted with a sensor, should be carried out by a CITROËN dealer.Any repair or any change of tyre, on a wheel fi tted with a sensor, Any repair or any change of tyre, on a wheel fi tted with a sensor,
The system may be affected from time to time by interference from radio transmissions on similar frequencies.
This function alerts you in the event of a tyre being defl ated or punctured. For this purpose, sen-sors continuously monitor the con-dition of the vehicle’s wheels.
This system does not absolve the driver of the need to check the tyre pressures regularly.
T Y R E D E F L A T I O N D E T E C T I O N
The SERVICE warning lamp comes on and a ve-hicle outline is displayed, accompanied by a mes-sage and a sound signal. The wheel(s) concerned will be shown fl ashing on the vehicle outline. Check the tyre pressures as soon as possible.
Defl ation warning
The STOP warning lamp comes on and a vehicle outline is displayed, ac-companied by a mes-sage and a sound signal. The wheel(s) concerned will be shown fl ashing on the vehi-cle outline. Stop the vehicle imme-diately, avoiding any violent actions on the steering wheel or brakes.
Puncture
Change the damaged wheel (whether punctured or substan-tially defl ated), have the tyre re-paired as soon as possible, then check the tyre pressures as soon as you can after that.
The wheel affected will no longer be detectable by the alert system if it is in the boot or undergoing re-pair. The spare wheel is not moni-tored by the alert system.
The SERVICE warning lamp comes on and a vehicle outline is dis-played, accompanied by a message and a sound signal. The wheel(s) concerned will be shown as ab-sent on the vehicle outline. If you have not changed a wheel, this in-formation indicates a malfunction-ing of the system.
Consult the CITROËN network to have the defective sensor(s) re-placed.
Wheel not monitored
The defl ation detection system is a driving assistance function which does not relieve the driver from the responsibility to be vigilant.
This system does not absolve the driver of the need to check the tyre pressures on a regular basis (see “Vehicle identifi cation"), to ensure that the vehicle behaves as it should and to avoid prema-ture wear on the tyres, especially when the vehicle is being subject-ed to heavy loads or driven at high speeds.
Do not forget to check the tyre pressure on the spare wheel.

198
VI
A C C E S S O R I E S
A wide range of accessories and parts are available from the CITROËN network.and parts are available and parts
These accessories and parts have been tested and approved for reli-ability and safety.
They are all adapted to the needs of your vehicle and come with a CITROËN guarantee.of your vehicle and come your vehicle
There are 5 families into which these accessories and parts are arranged :
"Comfort and leisure" :
fl oor mats*, boot tray, boot carpet, sun visors, mini-bar, fragrance dif-fuser, boosters and child seats, roof bars, bicycle carrier, ski carri-ers, roof box, towbars, etc.
The fi tting of electrical equipment or accesso-ries which are not rec-ommended by CITROËN may result in a failure of your ve-hicle’s electrical system and overconsumption.
We ask you to take note of this warning and advise you to con-tact a dealer who can show you the range of approved equip-ment and accessories.
"Safety" :
anti-intrusion alarm, anti wheel theft, stolen vehicle locating, medical kit, warning triangle, high-visibility vest, dog guard, snow chains, front foglamps kit, rear parking assistance, etc.
"Navigation and communication" :
audio systems, navigation sys-tems, CD changer, DVD player, Bluetooth hands-free kit, auxiliary cable to connect a portable MP3 player, USB Box, loudspeakers, etc.
Depending on the country of sale, the law may require you to carry high-visibility vests, warn-ing triangles and replacement bulbs in the vehicle.
"Personalisation" :
seat covers, alloy wheels, wheel trims, mud fl aps, door sill protec-tors, etc.
"Boutique products" :
screen wash fl uid, cleaning and in-terior/exterior maintenance prod-ucts, bodywork touch-up aerosol and pen, etc.
* To avoid any risk of interfering with the pedals :
- check that the fl oor mat is cor-rectly positioned and fi xed,
- never use more than one fl oor mat.

414141
IV
DBC
A
C D C H A N G E R S O U R C E
( A C C O R D I N G T O E Q U I P M E N T )
Hold down one of the buttons 1 to 5 on the alphanumeric keypad to choose the CD that you wish to play back.
1. Press on button C or rotate the control on the steering wheel D upwards to listen to the next CD.2. Press on button B or rotate the control on the steering wheel D downwards to listen to the previous CD.Note: Playback of the star t of the CD is automatic.After each change of source, on return to CD changer source, playback will resume at the same point where it had been interrupted.
WHAT IS THE CD CHANGER ?SELECTING A CD
P LAY BACK THE NEXT /PREVIOUS CD
or
CD CHANGER SOURCE
This device can accommodate 5 discs.
I NSERTING CDS INTO THE MAGAZINE
Insert the CDs printed sur face to the left.
Note:Each compartment takes one disc only.The CD changer will not operate if discs are inserted the wrong way up.
R EMOVING DISCS
To remove a CD, give a long press on the corresponding button A.
S ELECTING CD CHANGER SOURCE
Press successively on button 24, until the desired source is obtained.