service Citroen C4 PICASSO 2008 1.G Owner's Manual

Page 17 of 266

A
IN BRIEF
I
20
M O N I T O R I N G
Seat belts not fastened / unfastened warning lamp
This warning lamp informs you if the driver’s or front passenger’s seat belt is not fastened (depend-ing on model), and if the front pas-senger’s (depending on model) or the second- and third-row passen-gers’ seat belts are unfastened. The lit up positions represent those whose seat belts are not fastened / unfastened.
Locking from inside
You can use electrical central locking or unlocking by pressing on button A.
If one of the doors is open or is not closed properly, central lock-ing will not work.
Anti-intrusion security
When starting the engine, the sys-tem automatically locks the doors once you reach approximately 10 km/h (approximately 6 mph).
Tyre defl ation detection
This function warns you if a tyre is defl ated or punctured.
This system does not absolve the driver of the need to regularly check the tyre pressures.
The SERVICE warning lamp lights up, and a ve-hicle outline is displayed, accompanied by a mes-sage and a sound signal.
Defl ation warning
The STOP warning lamp lights up, and a vehicle outline is displayed, ac-companied by a message and a sound signal.
Puncture

Page 35 of 266

36
II
Depollution system warning lamp
If it fl ashes or lights up while you are driving, this indicates a depol-lution system malfunction.
Urgently contact a CITROËN dealer.
SERVICE warning lamp
This warning lamp remains on for as long as the fault relating to the alert message is present, for a seri-ous fault.
Urgently contact a CITROËN dealer.
The warning lamp remains on only temporarily in the case of mi-nor faults.
Contact a CITROËN dealer.
To recall the corresponding alert message, see “Log of alerts”.
Child safety warning lamp
When you activate the child safety, or each time you switch on the ig-nition, the warning lamp appears but goes out after 10 seconds (see chapter “Child safety”).
ABS system
The ABS warning lamp comes on when you switch on the ignition and should go off after a few seconds.
If the warning lamp does not go off, there may be a system mal-function (see “Brakes”).
Diesel engine preheater warning lamp
See the procedures for starting the engine.
See the chapter “Starting”.
Coolant temperature warning lamp
This comes on each time you switch on the ignition, for a few seconds. If it comes on while the engine is running, this indicates an abnormal increase in the coolant temperature.
It is essential to stop the vehicle. Check the coolant level, having tak-en all the appropriate precautions. If the level is satisfactory, contact a CITROËN dealer.If the level is satisfactory, contact a If the level is satisfactory, contact a
Warning lamp for detection of a door left open
When the engine is running, it comes on to indicate that a door, the bonnet and/or the boot is open.
Front / side airbag fault warning lamp
See “Airbags”.
Front passenger’s airbag deactivation warning lamp
See “Airbags”.
W A R N I N G L A M P S
Seat belt non-fastening/unfastening warning lamp (continued)
Seat belts unfastened dur-ing the journey :
- The point corresponding to the seat position with seat belt un-fastened lights up between 0 and 20 km/h. Above 20 km/h (approx. 12 mph), it fl ashes ac-companied by a sound signal for around 120 seconds. The sound signal stops when the ig-nition is switched off or if a door is opened.

Page 38 of 266

II
39
It informs you when the next routine service is due in accordance with the vehicle servicing schedule in the Maintenance Guide. This information is dependent on tw o parameters: the mileage covered, and the time elapsed since the last visit.
Operation
When the ignition is switched on a for a few seconds, the spanner symbolising maintenance opera-tions lights up ; the total mileage recorder display tells you the dis-tance remaining to the next serv-ice (in thousands and hundreds of kilometres, or miles).
Example : before the next service you can still travel :
Operation if the distance remaining to the next service is less than 1 000 km (approx. 600 miles)
Each time you switch on the igni-tion and for 5 seconds, the symbol and the distance fl ash.
Example : There remain up to the next service : 900 km (or miles).
On switching on the ignition and for 5 seconds, the instrument pan-el indicates :
Operation if the service interval has been exceeded
Each time you switch on the igni-tion, the spanner and the mileage covered (preceded by a minus) beyond the recommended interval fl ash.
Example : You have passed the service interval by 300 km (or miles).The routine service on your vehi-cle needs to be carried as soon as possible.
A few seconds after that, the total mileage recorder display appears.After a few seconds, the total mile-age indicator is displayed and the spanner remains lit.
A few seconds after switching on the ignition, the total mileage re-corder resumes its normal role and the spanner remains lit up.
M A I N T E N A N C E I N D I C A T O R

Page 64 of 266

–+II
65
The fl ashing of the warning lamp for the position reque
sted signals that this position is not yet obtained.If the warning lamp is on fi xed, the position is confi rmed.Display of a dash in the rev counter indicates a malfunction. Urgently contact a CITROËN dealer.If the warning lamp is on fi xed, the position is confi rmed.If the warning lamp is on fi xed, the position is confi rmed.
Lighting of the SERVICE warning lamp accompanied by a message an d a sound signal indicates a functioning anomaly. In this case :
- a marked snatching may be felt when selecting R for reverse gear,- the gearbox is locked on a gear,- do not exceed 100 km/h (approx. 60 mph).
Urgently contact a CITROËN dealer.
Sequential mode with manual gear changing
Position of the selector for manual gear changing.
- Move the selector to position M.
- Pull the lever “+” to change up a gear.
- Pull the lever “-” to change down a gear.
A U T O M A T I C G E A R B O X S E Q U E N T I A L M O D E
Observations :
- If the vehicle stops or reduces speed (for example when ap-proaching a stop sign), the gear-box changes down automatically to fi rst gear.
- In sequential mode, it is not necessary to release the accel-erator during gear changes.
- A request to change gear is ac-cepted only if the engine speed permits it.- For safety reasons, depending on the engine speed, a change up or down may be performed automatically.
- It is possible at any time to move from position D (driving in auto-matic mode) to position M (driv-ing in sequential mode) or vice versa.

Page 89 of 266

88
II
Stopping the function
- by an action on the control on position "REG" to position 0.
- by the engine stopping.
The cruise speed previously cho-sen is no longer memorised.
If there is a malfunction,a mes-sage will display accompanied by a sound signal and lighting of the SERVICE warning lamp.
Contact a CITROËN dealer.
Cruise control should only be used when the driving conditions allow you to drive at a constant speed.
Do not use it in heavy traffi c, or on dangerous or slippery roads.
The driver must remain attentive and in full control of his vehicle.
You are recommended to keep your feet within range of the pe dals.
To avoid any risk of interfering with the pedals :
- check that the fl oor mat is correctly positioned,
- never use more than one fl oor mat.
Re-engaging cruise control
-by recall of the memorised speed :
After a disengagement, press on button 3. Your vehicle automati-cally returns to the memorised cruise speed which is displayed in zone A.
If the memorised cruise speed is higher than the current speed, the vehicle wll accelerate to reach the former.
- by selection of the current speed :
Press on button 2 or 4 once the desired speed has been reached.The information "OFF" will thendisappear from zone A.
Observation : If during the opera-tion of cruise control, the system is unable to keep within the memo-rised speed (for example on a steep descent), then the speed fl ashes. Adapt your speed as necessary.
Disengaging of cruise control while retaining the memorised speed
- Either by pressing on the brake pedal or on the clutch pedal.
- Or by pressing button 3.
- Or if either the ESP or the ASR system is active.
Note : cruise control is not active if the gear lever is in neutral.
These actions cause the informa-tion "OFF" to appear in zone A of the instrument panel.
These manœuvres do not cancel the cruise speed which remains displayed in the instrument panel.
C R U I S E C O N T R O L

Page 91 of 266

90
II
Stopping the function
- by an action on the control on position "LIM" to position 0.
- by the engine stopping.
The speed previously chosen is still memorised.
If there is a malfunction,a mes-sage will display accompanied by a sound signal and lighting of the SERVICE warning lamp.
Contact a CITROËN dealer.
Temporary override of the maximum speed
The accelerator pedal is equipped with an end-of-travel switch. If you action this switch by pressing the pedal hard down, you can exceed the memorised maximum speed at any time.
During the time the speed is being exceeded, the displayed speed fl ashes.
You have only to release the ac-celerator pedal to return below the maximum speed and render the function active again.
Observation : If during the operation of the speed limiter, the system is unable to keep within the maximum speed (for example on a steep de-scent or under heavy acceleration) then the speed fl ashes. Adapt your speed as necessary.
The function will re-engage when your speed returns below the de-sired maximum speed.
Disengagement of the maximum speed
Press on button 3.
This action causes the information "OFF" to appear on the instru-ment panel screen.
Use of fl oor mats that are not approved by CITROËN may hinder access to the accelerator pedal and thus interfere with the func-tioning of the speed limiter.
To avoid any risk of interfering with the pedals :
- check that the fl oor mat is correctly positioned,
- never use more than one fl oor mat.
This action does not cancel the memorised maximum speed which remains displayed in zone A ofthe instrument panel.
S P E E D L I M I T E R

Page 92 of 266

II
D I E S E L P A R T I C U L A T E F I L T E R S Y S T E M
Complementary to the catalytic converter, this fi lter makes an active contribution to the preservation of air quality by the retaining of the unburnt pollutant particles. Black exhaust fumes are thus no longer emitted.
Clogging of the particle fi lter
If there is risk of clogging, a message appears on the multifun ction display, accompanied by a sound signal and lighting of the SERVICE warning lamp.
This alert tells you that the particle fi lter is starting to fi ll up (in conditions of urban driving of exceptionally lon g dura-tion: low speeds, traffi c jams etc.)
To regenerate the fi lter, it is advised to drive as soon as p ossible, when traffi c conditions permit, at a speed of 60 km/h (around 40 mph) or more for at least fi ve minutes (until t he alert message disappears).
If this alert persists, consult a CITROËN dealer.
Observation : After prolonged idling or driving at very low speeds, you may occa sionally notice water vapour be-ing emitted from the exhaust when accelerating. This is of no consequence to the running of the vehicle or to the environment.
Diesel fuel additive level
If the additive level becomes too low, a message appears on the multifunction display, accompanied by a sound signal and lighting of the SERVICE warning lamp. It is necessa ry to have the additive level topped up. Urgently consult a CITROËN dealer.signal and lighting of the SERlighting of

Page 93 of 266

A
92
II
This driving assistance device alerts you if you are wandering from your lane (continuous or dotted line marking on the road surface).
It is designed especially for use on motorways and dual carriage-ways, operating only at speeds above 80 km/h (approx. 50 mph).
Activation / Deactivation
A press on control A activates the function, the warning lamp on the control lights up.
A second press on control A de-activates the function, the warning lamp on the control goes out.
Whenever you start the engine, the mode (activated/deactivated), selected when you last switched off the engine, is retained.
The driver must still remain attentive and in complete control of the ve-hicle.
Operation
Provided you are travelling at over 80 km/h (approx. 50 mph), if you cross a lane marking, you are alerted by a vibration within the cushion of your seat :
- oriented to the right for crossing a lane marking to the right,
- oriented to the left for crossing a lane marking to the left.
The system does not alert you while your direction indicator is o perating, nor for about 20 seconds after your direction indicator has stopped.
Note : In the event of an electronic malfunction, a message is displayed, the SERVICE warning lamp comes on and a sound signal is heard. Con-tact a CITROËN dealer. warning lamp warning
Observations : This device is designed to identify traffi c lane markings.
In certain specifi c instances, it may trigger an unwanted alert, for example when you cross a direction arrow or some other random marking.
The effectiveness of the system may be temporarily affected by condi tions external to the vehicle :
• Detection of lanes made diffi cult by:
- Markings that are worn or erased.
- Insuffi cient contrast with the surface of the road.

Page 95 of 266

94
II
Proximity sensors are located in the front and rear bumpers of your vehicle.
Functioning
- When you engage reverse gear, a sound signal informs you that the system is active. The outline of your vehicle is displayed on the multi-function screen C or DT. Obstacles situated at the rear or in front of the vehicle will be detected.
- When you are moving forward, provided this is at a speed less than 10 km/h (approx. 6 mph), either in neutral or in gear, the outline on your vehicle is displayed on the screen as soon as an obstacle is dete cted in front of the vehicle. Obstacles located in front of the vehicle will be detected.
- In forward gear or in reverse gear, as the vehicle approaches the ob-stacle, the sound signal becomes more and more rapid and the ba rs are seen to move ever nearer to the vehicle.
- Whether in forward gear or in reverse gear, when theobstacle is close, the sound signal becomes continuous and the WARNING panel appears on the multifunction display.
Note : the sound signal is emitted by the loudspeakers that are nearest to the obstacle.
P A R K I N G A S S I S T A N C E
Multifunction screen DT
Multifunction screen C
This system can in no way replace vigilance and responsibility on the part of the driver.
When you engage reverse gear, a short sound signal followed by a different sound signal accompanied by a message and the lighting of the SERVICE warning lamp, indi cates that there is a malfunction.
Contact a CITROËN dealer.

Page 153 of 266

B
150
III
The rear pneumatic suspension enhances driving comfort by maintaining a constant body height what-ever the vehicle load.
OPERATION
- If there is an increase in vehicle load, a sinking of the rear of the vehicle is detected and the pneumatic springs infl ate in order to compensate for the extra weight.- If there is an decrease in load, a rising of the rear of the vehicle is detected and so the pneumatic springs defl ate to return the vehicle to its nominal height.- If the vehicle has been unused for a long period, the pneumatic springs may infl ate if necessary when you unlock or open a door, so as to return the vehicle to its nominal height.
Note: If you do not reactivate the system manually, the automatic correction will be activated as soon as the vehicle starts to move. During the correction, the SERVICE warning lamp lights up and a message on the screen reminds you not to exceed 10 km/h (6 mph).
Note : the automatic correction does not function if the doors or the tailgate are open.
The automatic correction operates even if your vehicle is in economy mode.
ACTIVATION / DEACTIVATION
The automatic correction can be deactivated :
- Press on the button B for approximately two seconds.
- Release the button when you hear a beep. Deactivation is confi rmed by the lighting of the LED on the button B.
It is essential that you should deactivate the system in the following instances :
- working under the vehicle,
- changing a wheel,
- transporting the vehicle on a truck or on a boot.
To reactivate the automatic correction :
- Press again on the button B for approximately two seconds.
- Release the button when you hear a beep. Activa-tion is confi rmed by the extinction of the LED on the button B.
In the event of the system malfunctioning, alert messages, always in association with the SERVICE warning lamp, will display in the instrument panel. Contact a CITROËN dealer as soon as possiblewarning lamp, will display in the instrument pan, will d.
Grand C4 PicassoC4 Picasso
P N E U M A T I C S U S P E N S I O N

Page:   1-10 11-20 next >