light Citroen C4 PICASSO 2016 2.G Repair Manual

223
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed01-2016
Panoramic sunroof
F Rotate the control A to slide the roof blind to the desired position (positions 1 to 4 ).
Closing the roof blindAnti-pinch
It is fitted with an electrically controlled blind.
Opening the roof blind
F Rotate the control A to position 0 to close
the   roof   blind. The
  blind   has   an   anti-pinch   function.
At the end of its travel, when the blind
encounters   an   obstacle   on   closing,   it   stops   and  
m

oves   back   slightly.
Following   a   fault   or   after   a   battery  
d

isconnection   during   the   movement   of   the   blind  o
r after it has stopped, you must re-initialise the
anti-pinch f unction:
F

p
lace the blind in the closed position,
F
 
p
ress   control   knob   B   for   approximately  
t

wo seconds.
5
Lighting and visibility

226
C4-Picasso-II_en_Chap06_securite_ed01-2016
Intelligent traction control
system ("Snow motion")
When this warning lamp comes on, coupled with the STOP  and   ABS   warning  
l

amps,   accompanied   by   an   audible   signal  
a

nd   a   message,   it   indicates   that   there  
i

s   a   fault   with   the   electronic   brake   force  
di

stribution
 (
EBFD).
Anti-lock braking system (ABS) and electronic brake force
distribution (EBFD)
The fixed illumination of this warning lamp indicates that there is a fault
with
  the   ABS. Depending
  on   version,   your   vehicle   has   a  s
ystem   to   help   driving   on   snow:   intelligent
traction control.
This system detects situations of difficult
sur face
  adhesion   that   could   make   it   difficult   to  
m

ove   off   or   make   progress   on   deep   fresh   snow  
o

r   compacted   snow.
In these situations, the intelligent traction
control limits the amount of wheel slip to
provide
  the   best   traction   and   trajectory   control  
f

or   your   vehicle.
The
  use   of   snow   tyres   is   strongly  
r

ecommended   on   sur faces   offering   low   levels  
o

f   adhesion.
When
  changing   wheels   (tyres   and  
r

ims), ensure that these are approved
for
  your   vehicle.
Normal
  operation   of   the   ABS   may   make  
i

tself   felt   by   slight   vibrations   of   the   brake  
ped

al.
In emergency braking, press ver y
firmly and maintain this pressure.
You must stop as soon as it is safe to do so.
In
 
both
 
cases,   have   the   system   checked   by   a  
C

ITROËN   dealer   or   a   qualified   workshop   as  
s

oon
 
as
 
possible.
The
 
vehicle   retains   conventional   braking.   Drive  
c

arefully
 
at   moderate   speed.
Safety

232
C4-Picasso-II_en_Chap06_securite_ed01-2016
The driver must ensure that passengers use the seat belts correctly and that they are all
fastened
  before   setting   off.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for short
journeys.
Do
  not   interchange   the   seat   belt   buckles   as  
t

hey   will   not   fulfill   their   role   fully.
The seat belts are fitted with an inertia reel
permitting
  automatic   adjustment   of   the  
l

ength   of   the   strap   to   your   size.   The   seat   belt  
i

s   stowed   automatically   when   not   in   use.
Before and after use, ensure that the seat
belt
  is   reeled   in   correctly.
The lower part of the strap must be
positioned
  as   low   as   possible   on   the   pelvis.
The upper part must be positioned in the
hollow
  of   the   shoulder.
The inertia reels are fitted with an automatic
locking
  device   which   comes   into   operation   in  
t

he   event   of   a   collision,   emergency   braking  
o

r   if   the   vehicle   rolls   over.   You   can   release  
t

he   device   by   pulling   the   strap   firmly   and  
t

hen   releasing   it   so   that   it   reels   in   slightly.Recommendations for children
Use a suitable child seat if the passenger is less than 12 years old or shorter than one
and
  a   half   metres.
Never use the same seat belt to secure more
than
  one   person.
Never
  allow   a   child   to   travel   on   your   lap.
For more information on Child seats , refer
to
  the   corresponding   section.
In
 
order
 
to
 
be
 
effective,
 
a
 
seat
 
belt
 
must:
-
 b
e
 
tightened
 
as
 
close
 
to
 
the
 
body
 
as
 p
ossible,
-

b

e pulled in front of you with a smooth
movement,
 
checking
 
that
 
it
 
does
 
not
 
t

wist,
-

b

e used to restrain only one person,
-
 
n

ot
 
bear
 
any
 
trace
 
of
 
cuts
 
or
 
fraying,
-

n

ot be converted or modified to avoid
affecting
 it

s
 p

erformance.
In the event of an impact
Depending on the nature and
seriousness of the impact , the
pretensioning
  device   may   be   deployed  
b

efore   and   independently   of   the   airbags.  
D

eployment of the pretensioners is
accompanied
  by   a   slight   discharge   of  
h

armless   smoke   and   a   noise,   due   to   the  
a

ctivation   of   the   pyrotechnic   cartridge  
i

ncorporated   in   the   system.
In
  all   cases,   the   airbag   warning   lamp   comes  
o

n.
Following
  an   impact,   have   the   seat   belts  
s

ystem   checked,   and   if   necessary   replaced,  
b

y a CITROËN dealer or a qualified
workshop.
In accordance with current safety
regulations,
 
for
 
all
 
repairs
 
on
 
your
 
vehicle's
 
s

eat
 
belts,
 
go
 
to
 
a
 
qualified
 
workshop
 
with
 t
he
 
skills
 
and
 
equipment
 
needed,
 
which
 
a
 C
ITROËN
 
dealer
 
is
 
able
 
to
 
provide.
Have
 
your
 
seat
 
belts
 
checked
 
regularly
 
by
 
a

 
CITROËN
 
dealer
 
or
 
a
 
qualified
 
workshop,
 
p

articularly
 
if
 
the
 
straps
 
show
 
signs
 
of
 
d

amage.
Clean the seat belt straps with soapy
water
 
or
 
a
 
textile
 
cleaning
 
product,
 
sold
 
by
 
C

ITROËN
 
dealers.
After
 
folding
 
or
 
moving
 
a
 
seat
 
or
 
rear
 
bench
 
s

eat, ensure that the seat belt is positioned
and
 
reeled
 
in
 
correctly.
Advice
Safety

233
C4-Picasso-II_en_Chap06_securite_ed01-2016
Airbags
System designed to contribute towards improving   the   safety   of   the   occupants   (with  
t

he   exception   of   the   rear   centre   passenger)  
i

n   the   event   of   violent   collisions.   The   airbags  
s

upplement   the   action   of   the   force-limiting  
s

eat   belts   (with   the   exception   of   the   rear   centre  
p

assenger).
If a collision occurs, the electronic detectors
record and analyse the front and side impacts
sustained
  in   the   impact   detection   zones:
-
 
i
n   the   case   of   a   serious   impact,   the   airbags  
a

re deployed instantly and contribute
towards better protection of the occupants
of
  the   vehicle   (with   the   exception   of   the  
r

ear   centre   passenger);   immediately   after  
t

he   impact,   the   airbags   deflate   rapidly   so  
t

hat   they   do   not   hinder   visibility   or   the   exit  
o

f the occupants,
-

i
n the case of a minor or rear impact or in
certain
  roll-over   conditions,   the   airbags  
m

ay   not   be   deployed;   the   seat   belt  
a

lone   contributes   towards   ensuring   your  
p

rotection   in   these   situations.
The airbags do not operate when the
ignition is switched off.
This
  equipment   will   only   deploy   once.  
I

f   a   second   impact   occurs   (during   the  
s

ame or a subsequent accident), the
airbag
  will   not   be   deployed   again. Deployment of one or more of the
airbags
  is   accompanied   by   a   slight  
e

mission   of   smoke   and   a   noise,   due  
t

o the activation of the pyrotechnic
cartridge
  incorporated   in   the   system.
This
  smoke   is   not   harmful,   but   sensitive  
i

ndividuals   may   experience   slight  
ir

ritation.
The noise of detonation related to the
deployment
  of   one   or   more   airbags   may  
r

esult   in   a   slight   loss   of   hearing   for   a  
s

hort   time.
Impact detection zones
A. Front  impact   zone.
B. S ide   impact   zone.
6
Safety

261
C4-Picasso-II_en_Chap07_info-pratiques_ed01-2016
Very cold climate screen(s)*
Removable protective screens which prevent the accumulation of snow at the radiator cooling fan.
D epending   on   version,   you   will   have   one   or   two   screens.
F
 
O
ffer   up   the   corresponding   very   cold  
c

limate screen to the upper or lower
section
  of   the   front   bumper.
F
 
P
ress   around   the   edge   of   each   screen   to  
e

ngage   its   fixing   clips   one   by   one.
F

U
se a screwdriver as a lever to release the
fixing
  clips   in   turn   on   each   screen.
Do
  not   forget   to   remove   the   very   cold   climate  
s

creen(s)
 w
hen:
-
 
t
he   ambient   temperature   exceeds   10   °C,
-
 tow

ing,
-
 
d
riving  
a
t  
s
peeds  
a
bove  
7
5  
m
ph  
(
120 km/h).
Removal Fitting
360 Vision system
The pre-cut zone must be removed
before  fitting   the   screen   to   the   front  
b

umper, to allow operation of the
camera.
When the very cold climate screen
is
  fitted,   the   image   provided   by   the  
c

amera   is   slightly   different.
* Depending
 
on
 
the
 
country
 
of
 
sale.
7
Practical information

278
C4-Picasso-II_en_Chap07_info-pratiques_ed01-2016
Brake wear depends on the style of   driving,   particularly   in   the   case o

f vehicles used in town, over short
distances.
  It   may   be   necessary   to   have
 t

he   condition   of   the   brakes   checked,
 e

ven   between   vehicle   services.
Brake pads
For information on checking brake disc wear, contact a CITROËN dealer
or
  a   qualified   workshop.
Brake disc wear
Only use products recommended by
CITROËN or products of equivalent
quality
 an
d
 sp
ecification.
In order to optimise the operation of
units as important as those in the
braking
  system,   CITROËN   selects   and  
o

ffers   very   specific   products.
After
  washing   the   vehicle,   dampness,  
o

r in wintry conditions, ice can form
on
  the   brake   discs   and   pads:   braking  
e

fficiency   may   be   reduced.   Make   light  
b

rake   applications   to   dry   and   defrost  
t

he   brakes.
Electric parking brake
For more information, refer to the " Electric
parking brake - Operating faults "
  section.
This system does not require any
routine
  servicing.   However,   in   the  
e

vent of a problem, have the system
checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Manual gearbox
The gearbox does not require any m
aintenance   (no   oil   change).
Refer
  to   the   manufacturer's   service  
s

chedule   for   the   checking   interval   for  
t

his
 c
omponent.
Automatic gearbox
The gearbox does not require any maintenance   (no   oil   change).
Refer
  to   the   manufacturer's   service  
s

chedule for details of the level
checking
  interval   for   this   component.
To
  avoid   damaging   the   electrical   units,  
n

ever use   a   high   pressure   jet   wash   in  
t

he   engine   compartment.
Unless
  there   is   a   leak   in   the   circuit,   a   drop   in  
t

he   brake   fluid   level   indicates   that   the   brake  
p

ads   are   worn.
Practical information

281
C4-Picasso-II_en_Chap07_info-pratiques_ed01-2016
Recommendations on storage
AdBlue® freezes at about -11°C and
deteriorates   above   25°C.   It   is   recommended  
t

hat bottles be stored in a cool area and
protected
  from   direct   sunlight.
Under
 
these   conditions,   the   fluid   can   be   kept  
f

or
 
at
 
least   a   year.
If the additive has frozen, it can be used once it
has
 
completely   thawed   out.
Procedure
Before topping-up, ensure that the vehicle is parked   on   a   flat   and   level   sur face.
In wintry conditions, ensure that the
temperature
  of   the   vehicle   is   above   -11°C.  
O

ther wise,   by   freezing,   the   AdBlue
® cannot
be
 
poured
 
into
 
its
 
tank.
 
Park
 
your
 
vehicle   in   a  
w

armer area for a few hours to allow the top-up
to
 
be
 
carried
 
out.
F
 
P

ress
 
the
 
START/STOP
 
button
 
to   switch  
o

ff
 
the
 
engine. F
F or access to the AdBlue® tank, raise the b
oot floor, or on 7-seat versions, unfold the
right
 
hand
 
seat
 
in
 
the
 
third
  row.
Never store bottles of AdBlue
® in your
vehicle.
F
 
W
ithout   pressing,   turn   the   black   cap   a  
q

uarter   turn   anti-clockwise   and   lift   it   off.
F

T
urn the blue cap a 6
th of a turn anti-
clockwise.
F
 
L

ift
 
off
 
the
 
cap.
F

O

btain a bottle of AdBlue
®. After first c
hecking
 
the
 
use-by
 
date,
  read   carefully  
t

he instructions on use on the label before
pouring
 
the
 
contents
 
of
 
the   bottle   into   your  
v

ehicle's
 Ad

Blue
® tank.
7
Practical information

301
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Changing a bulb
For H7 type bulbs with lugs... take care to observe their correct installation
so
  as   to   ensure   the   best   lighting  
p

erformance.
Risk of electrocution
Xenon bulbs (D5S-25W) must be
replaced by a CITROËN dealer or a
qualified
 w
orkshop.
Front lamps
Model with xenon headlamps
1. Directional dipped beam headlamps (D5S-25W).
2.
 M

ain   beam   headlamps   (H7-55W).
3.
 D

aytime   running   lamps   /   sidelamps
 (

6   light   emitting   diodes   -   LEDs).
4.
D

irection indicators
 (

6   light   emittng   diodes   -   LEDs).
5.
 F

ront   foglamps   (H11-55W).
Model with halogen headlamps
1. Dipped  beam   headlamps   (H7-55W).
2. M ain   beam   headlamps   (H7-55W).
3.
 D

aytime
 r
unning
 lam
ps/sidelamps
 (

4   light   emitting   diodes   -   LEDs).
4.
 D

irection   indicators   (PW Y24W).
5.
 F

oglamps
 (
H11-55W). In
  some   weather   conditions   (e.g.   low  
t

emperature or humidity), the presence
of   misting   on   the   internal   sur face   of   the  
g

lass   of   the   headlamps   and   rear   lamps  
i

s   normal;   it   disappears   after   the   lamps  
h

ave   been   on   for   a   few   minutes.
Light- emitting diodes - LEDs
For replacement, contact a CITROËN dealer or
qualified w
orkshop.
8
In the event of a breakdown

304
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
The direction indicator bulb is located below
the  front   lamp.
F

T
urn the bulb holder a quarter turn anti-
clockwise.
F
 
R
emove   the   bulb   holder.
F
 
C
hange   the   failed   bulb.
For reassembly, carry out these operations in
reverse
 o

rder.
Direction indicators Front foglamps
F Unclip  the   finisher   by   pulling   at   the   top.
F  R emove   the   two   screws   to   remove   the   unit.
F
 
T
urn   the   bulb   holder   a   quarter   turn.
F
 
R
emove   the   bulb   holder.
F
 
C
hange   the   failed   bulb.
For reassembly, carry out these operations in
reverse
  order,   pressing   on   the   finisher   to   refit   it.
Faster
 
flashing
 
of
 
a
 
direction
 
indicator
 
w

arning
 
lamp
 
(left
 
or
 
right)
 
indicates
 
a
 
f

ailed
 
bulb
 
on
 
that
 
side.
Direction indicators (light
emitting diodes - LED)
For the replacement of this type of lamp,
contact a CITROËN dealer or a qualified
workshop.
In the event of a breakdown

305
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
You should contact a CITROËN dealer or a
qualified  workshop   for   the   replacement   of   the  
l

ight-emitting   diode   -   LED.
Door mirror spotlamps
Integrated direction indicator
side repeaters
You should contact a CITROËN dealer or a
qualified  workshop   for   the   replacement   of   these  
b

ulbs. 1.
D

irection indicators (PY21W amber)
.
2.
 S
idelamps   /   foglamps   (P21/5W)
.
Rear lamps
Light-emitting diodes -
LEDs
For replacement, contact a CITROËN
dealer
  or   qualified   workshop.
3.
 B

rake
 
lamps
 
/
 
sidelamps
 
(light-emitting
 d
iodes
 
-
 
LEDs).
4. R
eversing
 
lamps
 
(W16W).
5.
 D

irection
 
indicators
 
(PY21W).
Model with LED lamps
3. Sidelamps ( 5W5).
4. B rake   lamps   (P21/ W).
5.
 D

irection   indicators   (W Y16W).
6.
 R

eversing   lamps   (W16W).
Model with conventional bulb lamps
8
In the event of a breakdown