spare wheel Citroen C5 2008 (RD/TD) / 2.G Owner's Manual

I
6
A
B
IN BRIEF
Access to the spare wheel
To access the spare wheel:1. Lift up the boot fl oor using the strap (saloon) or the retractable hook (Tourer).2. Fold back the boot carpet (saloon).3. Attach the hook to the upper section of the boot.4. To remove the spare wheel, detach the strap then push the wheel forwards, before lifting it out.
Spare wheel
Note: The tools are to be found in a protective holder inside the spare wheel.
173144
O P E N I N G
Bonnet release
This operation should only be performed while the vehicle is stationary.
Open the door.
To unlock, pull release lever A.
Lift up lever B, then raise the bon-net.
174
Puncture kit
The puncture repair kit is a com-plete system including a compres-sor and a setting product.
Saloon
Tourer

73
II
T Y R E D E F L A T I O N D E T E C T I O N
Wheel not detected
The defl ation detection system is a driving aid, but which does not absolve the driver from the need to be vigilant and responsible.
This system does not dispense with the requirement to check the tyres on a regular basis (see “Vehicle identifi cation”), to make sure that the vehicle is behaving correctly and to avoid premature tyre wear arising from driving too fast etc.
Do not forget to check the pres-sure in the spare wheel.
Any repair or replacement of a tyre on a wheel that is equipped with a sensor must be carried out by a CITROËN dealer.Any repair or replacement of a tyre on a wheel that is equippel tha
The system may suffer from temporary interference caused by radio transmissions on neighbouring frequencies.
Automatic detection:
A message indicates to you which tyre is punctured.
Driver request detection:
The vehicle outline indicates the punctured tyre(s).
The message is accompanied by the STOP warning lamp lighting up and a beep.
Puncture
Automatic detection:
A message indicates to you which wheel is not detected.
Driver request detection:
The vehicle outline indicates the wheel(s) which is/are not detected.
Press on Check
Automatic detection
Press on Check
Automatic detection
Note:If you have fi tted a wheel/wheels not equipped with tyre defl a-tion detection (e.g. snow tyres), contact a CITROËN dealertion detection (e.g. snow tyres), (e.g. snow .
The message is accompanied by the SERVICE warning lamp lighting up and a beep.Contact a CITROËN dealer to have the faulty sensor(s) replaced.

120
III
2
1
43
B O O T ( S A L O O N )
1 Battery for vehicles with V6 HDi engine.
2 Pull strap (spare wheel storage).
3 Boot lamp.
4 6 CD changer.
Luggage securing rings
Use the 4 securing rings on the boot fl oor to secure your luggage.
For safety reasons, in case of the need for sharp braking, you are advised to place heavy objects as far forward in the boot as possible.

167
VI
A
B
CD
C H A N G I N G B U L B S
R E A R L A M P S ( S A L O O N )
Rear lamp on wing
1 Remove the lateral boot trim fl ap A. To do so, pull it towards the inside of the boot, then pull it upwards.
2 Disconnect connector B.
3 Unscrew the 2 fi xings C.
4 Remove the lamp from its housing.
5 Detach the bulb holder D.
6 Replace the bulb.
7 Replace the bulb holder D.
8 Place the lamp in its housing.
9 Screw in the 2 fi xings C.
10 Connect connector B.
11 Refi t the trim A.
Note: You can use the spare wheel jack handle to screw or unscrew the fi xings C.

169
VI
A
B
CD
A
1
2
1
2
C H A N G I N G B U L B S
R E A R L A M P S ( T O U R E R )
Rear lamp on wing
Remove the lateral boot trim A.
To do so :
1 Pull it towards towards the inside of the boot.
2 Pull it upwards.
3 Disconnect the connector B.
4 Unscrew the fi xing screw C.
5 Remove the lamp from its housing.
6 Detach the bulb holder D.
7 Replace the faulty bumb.
8 Replace the bulb holder D.
9 Place the lamp in its housing.
10 Screw in the fi xing screw C.
11 Connect the connector B.
12 Refi t the trim A.
Note : You can use the spare wheel jack handle to screw or unscrew the fi xing screw C.

174
VI
35
6
1
2
4
C H A N G I N G A W H E E L
Access to the spare wheel
To access the spare wheel
1 Lift up the boot fl oor using the strap (saloon) or the retractable handle (Tourer).
2 Fold back the boot carpet (saloon).
3 Attach the hook to the upper section of the boot (in the middle of the boot pillar).
4 To remove the spare wheel, detach the strap then push the wheel forwards so as to be able to lift it.
Tools
The tools are to be found in a pro-tective holder inside the spare wheel. Pull back the retaining strap to have access.
1 Handle
2 Jack
3 Tool for the removal/refi tting of bolt protectors
4 Centring guide
5 Towing eye
6 Moveable chock
To reposition the spare wheel
To put the spare wheel back in the boot
1 Position the spare wheel fl at in the boot, then pull it towards you.
2 Next place the toolbox inside the wheel, then secure the assem-bly with the belt.
3 Release the strap to return the boot fl oor to its initial position.
Tyre pressures
The tyre pressure is indicated on the label located on the left-hand door centre pillar. On this label, the pressures are specifi ed, according to the vehicle load.

176
VI
If your vehicle is fi tted with a spare wheel of a different size to those on the vehicle, you must not exceed 80 km/h (50 mp h) whilst using the spare wheel.
The wheel bolts are specifi c to the type of wheel.
If the type of wheel is changed, check with your CITROËN dealer that the wheel bolts are compatible with the new wheels.
Note: take care to note down the code number engrav ed on the head of the anti-theft bolt socket. This will enable you to obtain replacement anti-theft bolt sockets from a dealership.
Spare wheel
Your vehicle may be fi tted with a different spare wheel to those on the vehicle. When fi tting the spare wheel, it is normal to notice that the wheel bolt washers do not come into contact with the wheel rim. The spare wheel is secured by the conical tapering of the wheel bolt’s shaft.
When refi tting the original wheel, ensure that the wheel bolt contact surfaces are clean and in good condition.
Refi tting a wheel
1 Fit the wheel on the hub, using the centring guide. Make sure that the contact surface between the hub and the wheel is clean.
2 Screw in the bolts but do not fully tighten them.
3 Lower the jack and remove it.
4 Tighten the wheel bolts, using the wheelbrace.
5 Refi t the protectors on the bolts.
6 Return the ground clearance to the normal position. See chap-ter “Hydractive III+ Suspen-sion”.
7 Ensure the tyre pressure is cor-rect (see “Vehicle identifi ca-tion”) and have the balancing checked.
Wheel equipped with defl ation detection sensor
Such wheels have tyre pressure sensors. It is essential to have repairs carried out by a CITROËN dealer.
Anti-theft bolts
Each wheel is equipped with one anti-theft bolt.
To remove it
1 Remove the protector using tool 3.
2 Use the anti-theft socket with the handle.
C H A N G I N G A W H E E L