light Citroen DS3 2014 1.G Owner's Guide

143
DS3_en_Chap07_visibilite_ed01-2014
A. courtesy lamp
B. M
ap reading lamps
Courtesy lam p
In this position, the courtesy lamp c
omes   on   gradually:
courtesy lamp
- when  the   vehicle   is   unlocked,
-  w hen   the   key   is   removed   from   the   ignition,
-

w
hen a door is opened,
-
 
w
hen   the   remote   control   locking   button   is  
a

ctivated,   in   order   to   locate   your   vehicle.
It
  switches   off   gradually:
-
 
w
hen   the   vehicle   is   locked,
-
 
w
hen   the   ignition   is   switched   on,
-
 
3
0   seconds   after   the   last   door   is   closed.
Permanently
  off.
Permanent
 l

ighting.
With the "permanent lighting" mode, the duration of lighting   varies,   depending   on   the   circumstances:
-
 
w
ith   the   ignition   off,   approximately
 t

en minutes,
-
 
i
n   energy   economy   mode,   approximately
 t

hirty seconds,
- with the engine running, unlimited.
Map reading lamps
F With   the   ignition   on,   press   the  c
orresponding s witch.
Visibility

DS3_en_Chap07_visibilite_ed01-2014
Interior mood lightingThe dimmed passenger compartment lighting improves visibility in the vehicle when the light 
i s   poor.
Switching on
At night, the illumination of footwells and the central   dashboard   storage   compartment   comes  
o

n   automatically   when   the   sidelamps   are  
s

witched   on.
Switching off
The interior mood lighting switches off automatically   when   the   sidelamps   are  
switched
  off.
It
  can   be   switched   off   manually   using   the  
i

nstrument   panel   lighting   rheostat   button.
F
 
W
ith   the   lighting   on,   press   several   times   on  
t

he   left   hand   button   of   the   instrument   panel  
t

o   progressively   reduce   the   dashboard  
l

ighting   level.
F
 
P
ress   again   to   reduce   the   lighting   level  
t

o   the   minimum   and   switch   off   the   interior  
m

ood
 l
ighting. This
  comes   on   automatically   when   the   boot   is  o
pened   and   goes   off   automatically   when   the  b
oot   is   closed.
Boot lamp
The lighting time varies according to the circumstances:
-  w hen   the   ignition   is   off,   approximately t

en minutes,
-
 
i
n   energy   economy   mode,   approximately
 t

hirty

seconds,
- when the engine is running, no limit.

Direction indicators
Selection of the left or right direction indicators to   signal   a   change   of   direction   of   the   vehicle.
F
 
L
eft:   lower   the   lighting   stalk   beyond   the  
p

oint   of   resistance.
F
 
R
ight:   raise   the   lighting   stalk   beyond   the  
p

oint   of   resistance.
Three flashes of the direction
indicators
F Press briefly upwards or downwards, without   going   beyond   the   point   of  
r

esistance;   the   direction   indicators   will  
f

lash   3   times.
Hazard warning lam ps
A visual warning by means of the direction i
ndicators to alert other road users to a vehicle
breakdown,
  towing   or   accident.
F

P
ress this button, the direction indicators
flash.
They
  can   operate   with   the   ignition   off.
Automatic operation of
hazard warning lamps
When braking in an emergency, depending on the   deceleration,   the   hazard   warning   lamps  
c

ome   on   automatically.
They
  switch   off   automatically   the   first   time   you  
a

ccelerate.
F
 
Y
ou   can   also   switch   them   off   by   pressing  
t

he   button.

Braking assistance systems
Group of supplementary systems which help you   to   obtain   optimum   braking   in   complete  
s

afety   in   emergency   situations:
-
 
a
nti-lock   braking   system   (ABS),
-
 
e
lectronic   brake   force   distribution   (EBFD),
-
 
e
mergency   braking   assistance   (EBA).Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the stability and manoeuvrability   of   your   vehicle   when   braking,  
i

n   particular   on   poor   or   slippery   sur faces.
Activation
The anti-lock braking system comes into operation   automatically   when   there   is   a   risk   of  
w

heel   lock.
Normal
  operation   of   the   ABS   may   make   itself  
f

elt   by   slight   vibration   of   the   brake   pedal.
When
  braking   in   an   emergency,   press  
v

ery   firmly   without   releasing   the  
p

ressure.
Operating fault
If this warning lamp comes on, together   with   the   STOP and ABS
warning
  lamps,   accompanied   by   an  
a

udible
 
signal   and   a   message   in   the   screen,   it  
i

ndicates
 
a   malfunction   of   the   electronic   brake  
f

orce distribution which could result in loss of
control
 
of
  the   vehicle   when   braking.
You must stop as soon as it is safe to do so.
When
  replacing   wheels   (tyres   and  
r

ims),   ensure   that   they   conform   to   the  
ma

nufacturer's
 r
ecommendations.
If
  this   warning   lamp   comes   on,  
a

ccompanied   by   an   audible   signal  
a

nd   a   message   in   the   screen,   it  
i

ndicates
 
a   malfunction   of   the   anti-lock   braking  
s

ystem
 
which   could   result   in   loss   of   control   of  
t

he
 
vehicle   when   braking.
In either case, contact a CITR
oË
N dealer or a
qualified
 w

orkshop.

The driver must ensure that passengers use the seat belts correctly and that they are all
restrained
  securely   before   setting   off.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for short
journeys.
Do
  not   interchange   the   seat   belt   buckles   as  
t

hey   will   not   fulfil   their   role   fully.
The seat belts are fitted with an inertia reel
permitting
  automatic   adjustment   of   the   length  
o

f   the   strap   to   your   size.   The   seat   belt   is  
s

towed   automatically   when   not   in   use.
be

fore and after use, ensure that the seat
belt
  is   reeled   in   correctly.
The
  lower   part   of   the   strap   must   be  
p

ositioned   as   low   as   possible   on   the   pelvis.
The
  upper   part   must   be   positioned   in   the  
h

ollow   of   the   shoulder.
The
  inertia   reels   are   fitted   with   an   automatic  
l

ocking   device   which   comes   into   operation   in  
t

he   event   of   a   collision,   emergency   braking  
o

r   if   the   vehicle   rolls   over.   You   can   release  
t

he   device   by   pulling   the   strap   firmly   and   then  
r

eleasing   it   so   that   it   reels   in   slightly.In
  order   to   be   effective,   a   seat   belt   must:
-  b e   tightened   as   close   to   the   body   as  
p

ossible,
-
 
b
e   pulled   in   front   of   you   with   a   smooth  
m

ovement,   checking   that   it   does   not  
t

wist,
-

b
e used to restrain only one person,
-
 
n
ot   bear   any   trace   of   cuts   or   fraying,
-
 
n
ot   be   converted   or   modified   to   avoid  
a

ffecting
 it
s
 p
erformance.
In
 
a
ccordance  
w
ith  
c
urrent  
s
afety  
r
egulations,  
f

or   all   repairs   on   your   vehicle's   seat   belts,   go  
t

o   a   qualified   workshop   with   the   skills   and  
e

quipment   needed,   which   a   CITROËN   dealer  
i

s   able   to   provide.
Have
  your   seat   belts   checked   regularly   by  
a

  CITROËN   dealer   or   a   qualified   workshop,  
p

articularly   if   the   straps   show   signs   of  
d

amage.
Clean the seat belt straps with soapy water or
a
  textile   cleaning   product,   sold   by   CITROËN  
d

ealers.
After
  folding   or   moving   a   seat   or   rear   bench  
s

eat, ensure that the seat belt is positioned
and
  reeled   in   correctly.Recommendations for
children
Use a suitable child seat if the passenger is less than 12 years old or shorter than one
and
  a   half   metres.
Never
  use   the   same   seat   belt   to   secure  
m

ore   than   one   person.
Never
  allow   a   child   to   travel   on   your   lap.
For
  more   information,   refer   to   the   "Child  
sea

ts"
 se
ction.
In the event of an impact
depending on the nature and seriousness
of the impact ,
  the   pretensioning   device   may  
b

e deployed before and independently of the
airbags.
  Deployment   of   the   pretensioners  
i

s   accompanied   by   a   slight   discharge   of  
h

armless   smoke   and   a   noise,   due   to   the  
a

ctivation   of   the   pyrotechnic   cartridge  
i

ncorporated   in   the   system.
In
  all   cases,   the   airbag   warning   lamp   comes   on.
Following
  an   impact,   have   the   seat   belts  
s

ystem   checked,   and   if   necessary   replaced,  
b

y a CITR
oË
N dealer or a qualified
workshop.

165
DS3_en_Chap08_securite_ed01-2014
Airbags
System designed to contribute towards improving   the   safety   of   the   occupants   (with  
t

he   exception   of   the   rear   centre   passenger)  
i

n   the   event   of   violent   collisions.   The   airbags  
s

upplement   the   action   of   the   force-limiting  
s

eat   belts   (with   the   exception   of   the   centre   rear  
p

assenger).
If a collision occurs, the electronic detectors
record
  and   analyse   the   front   and   side   impacts  
s

ustained   in   the   impact   detection   zones:
-
 
i
n   the   case   of   a   serious   impact,   the   airbags  
a

re deployed instantly and contribute
towards better protection of the occupants
of
  the   vehicle   (with   the   exception   of   the  
r

ear   centre   passenger);   immediately   after  
t

he   impact,   the   airbags   deflate   rapidly   so  
t

hat   they   do   not   hinder   visibility   or   the   exit  
o

f the occupants,
-
 
i
n   the   case   of   a   minor   or   rear   impact   or   in  
c

ertain   roll-over   conditions,   the   airbags  
m

ay   not   be   deployed;   the   seat   belt  
a

lone   contributes   towards   ensuring   your  
p

rotection   in   these   situations. This
  equipment   will   only   deploy   once.  
I

f   a   second   impact   occurs   (during   the  
s

ame   or   a   subsequent   accident),   the  
a

irbag   will   not   be   deployed   again.
Impact detection zones
A. Front  impact   zone.
B. S ide   impact   zone.
Deployment
  of   one   or   more   of   the  
a

irbags   is   accompanied   by   a   slight  
e

mission   of   smoke   and   a   noise,   due  
t

o the activation of the pyrotechnic
cartridge
  incorporated   in   the   system.
This
  smoke   is   not   harmful,   but   sensitive  
i

ndividuals   may   experience   slight  
ir

ritation.
The noise of detonation related to the
deployment
  of   one   or   more   airbags  
m

ay   result   in   a   slight   loss   of   hearing   for  
a

  short   time.
The airbags do not operate when the
ignition is switched off.
Safety

DS3_en_Chap10_info-pratiques_ed01-2014
Never store bottles of adblue® in
your vehicle.
a

d
blu

e
® freezes at about -11°C and d
eteriorates   above   25°C.   It   is   recommended  
t

hat bottles be stored in a cool area and
protected
  from   direct   sunlight.
Under these conditions, the additive can be
kept
 
for
 
at   least   a   year.
If the additive has frozen, can be used once it
has
 
completely   thawed   out.
Recommendations on storage
Before topping-up, ensure that the vehicle is parked   on   a   flat   and   level   sur face.
In wintry conditions, ensure that the
temperature
  of   the   vehicle   is   above   -11°C.  
O

ther wise,   by   freezing,   the   AdBlue
® cannot
be
 
poured
 
into
 
its
 
tank.
 
Park
 
your
 
vehicle   in   a  
w

armer
 
area
 
for
 
a
 
few
 
hours
 
to
 
allow   the   top-up  
t

o
 
be
 
carried
 
out.
Procedure
F Switch   off   the   ignition   and   remove   the   key.
F
F
or access to the a
dbl
ue
® tank, raise the b
oot
 
carpet
 
then,
 
depending   on   equipment,  
l

ift
 
out
 
the
 
spare
 
wheel
 
and/or   the   storage  
b

ox.
F
 
W

ithout
 
pressing,
 
turn
 
the
  black   cap   a  
q

uarter
 
turn
 
anti-clockwise   and   lift   it   off.
F

T

urn the blue cap a 6
th of a turn anti-
clockwise.
F
 
L

ift
 
off
 
the
 
cap.

209
DS3_en_Chap10_info-pratiques_ed01-2014
Putting the wheel back in place
F Put  the   box   back   in   place   in   the   centre   of  t
he   wheel   and   clip   it.
F
 
P
ut   the   polystyrene   storage   box   back   in  
p

lace.
F
 
R
efit   the   boot   floor   carpet   by   lightly   folding  
i

t   in   the   middle   (refer   to   the   "Boot   fittings"  
s

ection).
F
 P
ut
 
the
 
wheel
 
back
 
in
 
its
 
housing.
F
U
nscrew the yellow central bolt by a few
turns then place it in the centre of the
wheel.
F
 
T

ighten
 
fully
 
until
 
the
 
central
 
bolt
 
clicks
 
to
 
r

etain
 
the
 
wheel
 
correctly.on v ehicles equipped with a "space-
saver" type spare wheel, the punctured
wheel can be stowed in place of the
"space-saver"
  wheel;   however   the   boot  
f

loor   will   not   then   be   flat.
Practical information

217
DS3_en_Chap10_info-pratiques_ed01-2014
changing main beam headlamp bulbschanging sidelamp bulbs
F Remove  the   protective   cover   by   pulling   the  t
ab.
F
 
D
isconnect   the   bulb   connector.
F
 
S
pread   the   springs   to   release   the   bulb.
F
 
R
emove   the   bulb   and   change   it.
To refit, carry out these operations in reverse
o r d e r. F
 R emove   the   protective   cover   by   pulling   the  t
ab.
F
 
P
ull   the   bulb   holder   pressing   on   the   tabs   on  
bo

th
 s
ides.
F
 
P
ull   the   bulb   and   change   it.
To refit, carry out these operations in reverse
o r d e r.
LEd* / Xenon front lamps
* LED: light-emitting diode.
1.

di
rection indicators (LE
ds
).
2.
S
idelamps (LE d s).
3.
di
pped beam headlamps (Xenon).
4.
M
ain beam headlamps (LE
ds / Xe
non).
5.
da
ytime running lamps (LE d s).
6.
F
ront foglamps (PSX24W).
For   replacements   on   of   these   types   of   lamps  
(

LED   /   Xenon),   contact   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Practical information

223
DS3_en_Chap10_info-pratiques_ed01-2014
Interior lighting
Interior lamp (1 / W5W)
Detach the cover of the interior lamp 1 with a
t hin screwdriver, close to the button, to access
the
  faulty   bulb.
Map reading lamps (2 / W5W)
Detach the cover of the interior lamp 1.   To  a
ccess the faulty bulb, detach the partition for
the
  reading   lamp   2  
c
oncerned.
Boot lamp (W5W)
Detach the unit by pushing it rear wards.
Footwell and central storage
lamps (W5W)
Detach the unit for access to the bulb.
Glove box lamp (W5W)
Detach the unit for access to the bulb.
Practical information