turn signal Citroen DS3 RHD 2016 1.G Owner's Manual

Page 37 of 380

35
With the engine running, when the needle is:
-  i n   zone   A,
  the   temperature   is   correct,
-
 
i
n   zone   B,   the   temperature   is   too   high;  
t

he central STOP
 
warning   lamp   and   the  
m

aximum   temperature   warning   lamp 1
come
  on   in   red,   accompanied   by   an  
a

udible   signal   and   a   message   in   the  
m

ultifunction
 s
creen.
You must stop as soon as it is safe to do so.
Wait
  a   few   minutes   before   switching   off   the  
e

ngine.
Contact
  a   CITROËN   dealer   or   a   qualified  
w

orkshop.
Coolant temperature indicator
After driving for a few minutes, the temperature and   pressure   in   the   cooling   system   increase.
To
  top   up   the   level:
F
 
w
ait   for   the   engine   to   cool   down,
F

u
nscrew the cap by two turns to allow the
pressure
  to   drop,
F
 
w
hen   the   pressure   has   dropped,   remove  
t

he cap,
F
 
t
op   up   the   level   to   the   "MA X"   mark.
Monitoring

Page 109 of 380

107
To facilitate unlocking of the steering column,   put   the   front   wheels   in   the  
s

traight  
a
head  
p
osition  
b
efore  
s
witching  
t

he   ignition   off.
Never
  switch   the   ignition   off   until   the
 v

ehicle   has   come   to   a   complete   stop
 a

nd   the   parking   brake   has   been   applied.
 W

ith   the   engine   stopped,   the   braking   and
 s

teering   assistance   systems   are   also   cut
 o

ff:   risk   of   loss   of   control   of   the   vehicle.When
  you   leave   the   vehicle,   take   the  
k

ey   with   you   and   lock   the   vehicle.
For   more   information,   refer   to   the  
"

Energy   economy   mode"   section.
Key reminder
If the key is left in the ignition switch, an audible   signal   sounds   when   the   driver's  
d

oor   is   opened.
Switching the engine off
F Immobilise   the   vehicle.
F  W ith   the   engine   at   idle,   turn   the   key   fully  
t

owards   you   to   position   1 (Stop).
F
 
R
emove   the   key   from   the   ignition   switch.
F
 
T
o   lock   the   steering   column,   turn   the  
s

teering   wheel   until   it   locks.
F
 
E
nsure   that   the   parking   brake   is   applied  
c

orrectly,   particularly   when   on   a   slope.
Energy economy mode
After switching off the engine (position 1 - Stop), y
ou   can   still   use   functions   such   as   the   audio a

nd   telematic   system,   the   wipers,   dipped   beam,
 c

ourtesy   lamps,   etc.,   for   maximum   cumulative
 p

eriod   of   30   minutes.
driving

Page 118 of 380

When you move the selector in the gate to select   a   position,   the   corresponding   indicator   is  
d

isplayed   in   the   instrument   panel.
P.
 Pa

rk
R.
R

everse
n. N

eutral
d

.
 D
rive   (Automatic   driving)
S.
Sport
 pro
gramme
T .
Snow
 pro
gramme
1 2 3 4.
  
G
ears   engaged   during   manual  
ope

ration
-.
 I

nvalid   value   during   manual   operation
displays in the instrument panel
Foot on brake
F Press  the   brake   pedal   when   this  i
ndicator   lamp   is   displayed   in   the  
i

nstrument   panel   (e.g.:   starting  
t

he
 eng
ine).
Moving off
If position n is selected inadvertently while   driving,   allow   the   engine   to  
r

eturn   to   idle   then   select   position  d to
accelerate.
If
  the   ambient   temperature   is  
b

elow -23°C,   the   engine   should   be   left  
a

t   idle   for   four   minutes,   to   ensure   the  
c

orrect   operation   and   life   of   the   engine  
an

d
 g
earbox. When
  the   engine   is   running   at   idle,   with  
t

he   brakes   released,   if   position   R
, d or
M   is   selected,   the   vehicle   moves   even  
w

ithout   the   accelerator   being   pressed.
When   the   engine   is   running,   never  
l

eave   children   in   the   vehicle   without  
sup

ervision.
When   carrying   out   maintenance   with  
t

he   engine   running,   apply   the   parking  
b

rake   and   select   position   P
.
F
 
A

pply   the   parking   brake.
F

Sel
ect position P or n
.
F

 
S

tart   the   engine.
If
 
this
 
procedure   is   not   followed,   there   is   an  
a

udible   signal,   accompanied   by   the   display   of  
a

n
 
warning   message.
F
 
W
ith   the   engine   running,   press   the   brake  
ped

al.
F
 
R

elease   the   parking   brake.
F

Sel
ect position R
, d or M
.
F
 
G

radually   release   the   brake   pedal.
The
 
vehicle   moves   off   immediately.

Page 120 of 380

There is a risk of damage to the gearbox:
-  i f   you   press   the   accelerator   and  
b

rake   pedals   at   the   same   time,
-
 
i
f   you   force   the   movement   of   the  
s

elector   from   the   P position to
another position when the battery
is
  flat.
To
  reduce   fuel   consumption   when   at  
a

  prolonged   standstill   with   the   engine  
r

unning   (traffic   jam...),   put   the   selector  
i

n the n  position   and   apply   the   parking  
b

rake.
If the selector is not in position P
,
when
 
the
 
driver's
 
door
 
is
 
opened
 
or
 
a

pproximately
 
45
 
seconds
 
after
 
the
 
i

gnition
 
is
 
switched
 
off,
 
a
 
warning
 
m

essage
 
appears
 
in
 
the
 
screen.
F

R

eturn the selector to position P ;
 
t

he
 
message
 
disappears.
When
 
driving
 
on
 
flooded
 
roads
 
or
 
when
 
c

rossing
 
a
 
ford,
 
proceed
 
at
 
walking
 
p

ace.
Operating fault
Manual operation
When the ignition is on, the lighting o
f   this   warning   lamp,   accompanied  
b

y
 
an
 
audible   signal   and   a   message   in   the  
m

ultifunction   screen,   indicates   a   gearbox   fault.
In
 
this
 
case,   the   gearbox   switches   to   back-up  
m

ode
 
and
 
is   locked   in   3rd   gear.   You   may   feel  
a

 
substantial   knock   when   changing   from   P
to R
 
and
 
from  n to R .
  This   will   not   cause   any  
d

amage
 
to
 
the   gearbox.
Do
 
not
 
exceed   60   mph   (100   km/h),   local   speed  
r

estrictions
 p
ermitting.
Contact
 
a
 
CITROËN   dealer   or   a   qualified  
w

orkshop
 
as   soon   as   possible.
F
Sel
ect position M for sequential c
hanging o
f
 
the
 
four
 
gears.
F
 
P

ush
 
the
 
selector
 
towards
 
the
 
+
 
sign
 
to
 
c

hange
 
up
 
a
 
gear.
F
 
P

ull
 
the
 
selector
 
towards
 
the
 
-
 
sign
 
to
 
c

hange
 
down
 
a
 
gear.
It
 
is
 
only
 
possible
 
to
 
change
 
from
 
one
 
gear
 
to
 
a

nother
 
if
 
the
 
vehicle
 
speed
 
and
 
engine
 
speed
 
p

ermit;
 
other wise,
 
the
 
gearbox
 
will
 
operate
 
t

emporarily
 
in
 
automatic
 
mode. This
 
symbol
 
is
 
displayed
 
if
 
a
 
gear
 
i

s
 
not
 
engaged
 
correctly
 
(selector
 
b

etween
 
two
 
positions).
d

 
disappears
 
and
 
the
 
gears
 
e

ngaged
 
appear
 
in
 
succession
 
in
 
the
 
in

strument
 pan

el.
Stopping the vehicle
Before switching off the engine, you can engage p osition P or

to   place   the   gearbox   in   neutral.
In
  both   cases,   apply   the   parking   brake   to  
i

mmobilise   the   vehicle.
Invalid value during manual
operation
If the engine speed is too low or too high, the gear   selected   flashes   for   a   few   seconds,   then  
t

he   actual   gear   engaged   is   displayed.
It
  is   possible   to   change   from   position  d
(automatic)
  to   position   M   (manual)   at   any   time.
When
  the   vehicle   is   stationary   or   moving  
v

ery   slowly,   the   gearbox   selects   gear   M1
automatically.
The
  sport   and   snow   programmes   do   not  
o

perate   in   manual   mode.

Page 122 of 380

Moving off
F Apply  the   parking   brake.
F Sel ect position P or n.
F
 
S
tart   the   engine.
If
  these   conditions   are   not   met,   there   is   an  
a

udible   signal,   accompanied   by   the   display   of  
a

n   warning   message.
F
 
W
ith   the   engine   running,   press   the   brake  
ped

al.
F
 
R
elease   the   parking   brake.
F

Sel
ect position R ,
d or M.
F
 
G
radually   release   the   brake   pedal.
The
  vehicle   moves   off   immediately.
If position
n  is   selected   inadvertently  
w

hile   driving,   allow   the   engine   to  
r

eturn   to   idle   then   select   position  d to
accelerate.
If
  the   ambient   temperature   is  
b

elow -23°C,   the   engine   should   be   left  
a

t   idle   for   four   minutes,   to   ensure   the  
c

orrect   operation   and   life   of   the   engine  
an

d
 g
earbox. When
  the   engine   is   running   at   idle,   with  
t

he   brakes   released,   if   position   R,
d or
M
  is   selected,   the   vehicle   moves   even  
w

ithout   the   accelerator   being   pressed.
When
  the   engine   is   running,   never  
l

eave   children   in   the   vehicle   without  
sup

ervision.
When
  carrying   out   maintenance   with  
t

he   engine   running,   apply   the   parking  
b

rake   and   select   position   P.

Page 124 of 380

To reduce fuel consumption when at a  prolonged   standstill   with   the   engine  
r

unning   (traffic   jam...),   put   the   selector  
i

n the n  position   and   apply   the   parking  
b

rake.
If the selector is not in position P
,
when
 
the
 
driver's
 
door
 
is
 
opened
 
or
 
a

pproximately
 
45
 
seconds
 
after
 
the
 
i

gnition
 
is
 
switched
 
off,
 
a
 
warning
 
m

essage
 
appears
 
in
 
the
 
screen.
F
R
eturn the selector to position P
;
 t
he
 
message
 
disappears.
When
 
driving
 
on
 
flooded
 
roads
 
or
 
when
 
c

rossing
 
a
 
ford,
 
proceed
 
at
 
walking
 
p

ace. There
  is   a   risk   of   damage   to   the   gearbox:
-  
i
f   you   press   the   accelerator   and  
b

rake   pedals   at   the   same   time,
-  
i
f   you   force   the   movement   of   the  
s

elector   from   the   P position to
another position when the battery
is   flat.
F

Sel

ect position M for sequential
 c

hanging
 o

f
 
the
 
six
 
gears.
F
 
M

ove
 
the
 
selector
 
towards
 
the
 
+
 
sign
 
to
 
c

hange
 
up
 
a
 
gear.
F
 
M

ove
 
the
 
selector
 
towards
 
the
 
-
 
sign
 
to
 
c

hange
 
down
 
a
 
gear.
It
 
is
 
only
 
possible
 
to
 
change
 
from
 
one
 
gear
 
to
 
a

nother
 
if
 
the
 
vehicle
 
speed
 
and
 
engine
 
speed
 
p

ermit;
 
other wise,
 
the
 
gearbox
 
will
 
operate
 
t

emporarily
 
in
 
automatic
 
mode.
Manual operation
d disappears and the gears e
ngaged   appear   in   succession   in   the  
in

strument
 pan
el.
If
 
the
 
engine   speed   is   too   low   or   too   high,   the  
g

ear
 
selected   flashes   for   a   few   seconds,   then  
t

he
 
actual
  gear   engaged   is   displayed.
It
 
is
 
possible   to   change   from   position  d
(automatic)
  to   position   M   (manual)   at   any   time.
When
 
the
  vehicle   is   stationary   or   moving  
v

ery
 
slowly,   the   gearbox   engages   first   gear  
au

tomatically.
Invalid value during manual
operation
This symbol is displayed if a gear i s   not   engaged   correctly   (selector  
b

etween   two   positions).
Stopping the vehicle
Before switching off the engine, you can engage   position   P or n  to   place   the   gearbox   in  
neu

tral.
In
  both   cases,   apply   the   parking   brake   to  
i

mmobilise   the   vehicle. When
  the   ignition   is   on,   the   lighting  
o

f   this   warning   lamp,   accompanied  
Operating fault
by an audible signal and a message in the m
ultifunction   screen,   indicates   a   gearbox   fault.
In
  this   case,   the   gearbox   switches   to   back-up  
m

ode   and   is   locked   in   3rd   gear.   You   may   feel  
a

  substantial   knock   when   changing   from   P
to R
  and   from  n to R.
  This   will   not   cause   any  
d

amage   to   the   gearbox.
Do
  not   exceed   60   mph   (100   km/h),   local   speed  
r

estrictions
 p
ermitting.
Contact
  a   CITROËN   dealer   or   a   qualified  
w

orkshop   as   soon   as   possible.

Page 143 of 380

141
The temporary illumination of the dipped beam headlamps   after   the   vehicle's   ignition   has   been  
s

witched   off   makes   the   driver's   exit   easier  
w

hen   the   light   is   poor.
Switching on
F With  the   ignition   off,   "flash"   the   headlamps  u
sing   the   lighting   stalk.
F
 
A
  further   "headlamp   flash"   switches   the  
f

unction   off.
Switching off
The manual guide-me-home lighting switches off   automatically   after   a   set   time.
Manual guide-me-home
lighting
The sidelamps and dipped beam headlamps are   switched   on   automatically,   without   any  
a

ction   on   the   part   of   the   driver,   when   a   low   level  
o

f   external   light   is   detected   or   in   certain   cases  
o

f   activation   of   the   windscreen   wipers.
As
  soon   as   the   brightness   returns   to   an  
a

dequate   level   or   after   the   windscreen   wipers  
a

re   switched   off,   these   lamps   are   switched   off  
a

utomatically   and   the   daytime   running   lamps  
c

ome   on.
Automatic illumination of
headlamps
Activation
F Turn   ring   to   the   "AUTO"  position.   The  a
ctivation   of   the   function   is   confirmed   by  
t

he   display   of   a   message.
deactivation
F Turn  ring   to   a   position   other   than   "AUTO".  T
he   deactivation   of   the   function   is  
c

onfirmed   by   the   display   of   a   message.
Operating fault
In the event of a fault with the
sunshine  sensor,   the   lighting   come  
o

n,   this   warning   lamp   is   displayed  
o

n   the   instrument   panel   and/or   a  
m

essage   appears   in   the   screen,  
a

ccompanied   by   an   audible   signal.
Contact
 
a
 
CITROËN   or   a   qualified   workshop  
w

orkshop.
Visibility

Page 204 of 380

Important:   if   your   vehicle's  Ad
Blue® tank is completely empty - w
hich
 
is
  confirmed   by   the   alert  
m

essages   and   the   impossibility   of  
s

tarting
 
the   engine,   you   must   add   at  
l

east
 
3.8   litres   (so   two   1.89   litre   bottles).If
  any   additive   is   split   or   splashed,   wash  
i

mmediately   with   cold   water   or   wipe  
w

ith   a   damp   cloth.
If   the   additive   has   crystallised,   clean   it  
o

ff   using   a   sponge   and   hot   water.Important:
 i
n the event of a top-up after
a breakdown because of a lack of
additive ,   signalled   by   the   message   "Top
 u

p   emissions   additive:   Starting   prevented",
 y

ou   must   wait   around   5   minutes   before
 s

witching  
o
n  
t
he  
i
gnition,  
w
ithout opening
the driver's door, locking the vehicle
or introducing the key into the ignition
switch .
Switch   on   the   ignition,   then,   after
 1

0 seconds,   start   the   engine.
F
 
O

btain
 
a
 
bottle   of   AdBlue
®. After first c
hecking
 
the
 
use-by
 
date,
  read   carefully  
t

he instructions on use on the label before
pouring
 
the
 
contents
 
of
 
the   bottle   into   your  
v

ehicle's
 Ad

Blue
® tank. N ever   dispose   of   AdBlue
® additive b
ottles
 
in
 
the
 
household
 
waste.   Place  
t

hem
 
in
 
a
 
special
 
container   provided  
t

his
 
purpose
 
or
 
take
 
them
  to   your  
d

ealer.
F
 
A

fter
 
emptying
 
the
 
bottle,
 
wipe
 
away
 
any
 
s

pillage
 
around
 
the
 
tank
 
filler
 
using
 
a
 
damp
 
c

loth.
F
 
R

efit
 
the
 
blue
 
cap
 
to
 
the
 
tank
 
and
 
turn
 
it
 
a


6
th of a turn clockwise, to its stop.
F
 R
efit   the   black   cap   and   turn   it   a   quarter   of  
a

 
turn   clockwise   without   pressing.   Ensure  
t

hat
  the   indicator   on   the   cap   lines   up   with  
t

he
 
indicator   on   the   support.
F
 
D

epending   on   equipment,   return   the   spare  
w

heel   and/or   the   storage   box   to   the   bottom  
o

f
 
the   boot.
F
 
R

efit   the   boot   carpet   and   close   the   tailgate.