engine Citroen GRAND C4 PICASSO RHD 2013 1.G Service Manual

128
Comfort
1. Screen power switch 2.
Display adjustment buttons


Each head
phone set has a switch,
a connection indicator lamp (blue)and a channel selector (A or B).
) With the engine running, connect your
portable system to the RCA connectors (e.g. with AV1 on the left). ) Press the switch on the control panel,
the indicator lamp comes on and the AV1
indicator lamps come on.
) Make a long press on the switch, its
indicator lamp flashes in blue.) Make a long press on the control panelswitch, the pairing with the headphone set
is complete when the blue indicator lampson the headphones and on the system areon continuously. ) Repeat the operation for the other
headphone set.
) Press the screen switch if you have a video source. )
Start playing your por table system.


Operation


The Multimedia system allows theconnection of a third Bluetoothheadphone set, not supplied.


If your seat is in the table position,position a cover to avoid damaging thescreen.
These covers also conceal eachscreen.

)It is possible at any time to modify thesource for the video display (using button 6or 7
on the control panel: the indicator lamp for the source selected comes on) as well as the audio channel (using the selector on
the headphones).

135
4
Driving








Starting-switching off the engine with the electronic key
)Place the gear selector lever at Nfor
vehicles with an electronic gearbox, Por Nfor vehicles with an automatic gearbox or neutral with a manual gearbox. )Inser t the electronic key in the reader.)Press the brake pedal for vehicles with an electronic or automatic gearbox, or
fully declutch for vehicles with a manualgearbox.

Starting the engine
For Diesel vehicles, intemperatures below zero theengine will not star t until the preheater warning lamp has gone off.
If this warning lamp comes on after pressing "STA R T/STOP", you should hold the brake or clutch pedal down
until the warning lamp goes off and do not press the START/STOP buttonagain.



If one of the star ting conditions is notmet, a reminder message appears in the instrument panel screen. In somecircumstances, it is necessary to turnthe steering wheel slightly while pressingthe "STA R T/STOP" button to assistunlocking of the steering; a messagewarns you when this is needed.
)
Briefly press the " START/STOP"button.
The steering column unlocks and
the engine star ts more or less
immediatel
y (see the advice for
Diesel versions).

136
Driving
Electronic key left in the reader
If the electronic key is left in the reader,on opening the driver's door a message appears to warn you. In the event o
f an emergency only,
the engine can be switched off
without any conditions. To do this,press the "STA R T/STOP" button for about three seconds.
In this case the steering column locks
as soon as the vehicle stops

Emergency stop
)Immobilise the vehicle. )Place the gear selector lever at Nfor
vehicles with an electronic gearbox, Por Nfor an automatic gearbox, or neutral with amanual gearbox.
Switching off the engine

If the vehicle is not immobilised, the engine will not stop.

)
Briefly press the " START/STOP
"button
The engine stops and the steering column locks.
)Remove the electronic key from the reader.

137
4
Driving








Starting-switching off the engine with the "Keyless Entry and
Starting" system
)Place the gear selector lever at Nfor
vehicles with an electronic gearbox, Por Nwith an automatic gearbox, or neutral witha manual gearbox. )With the electronic key inside the vehicle (it is not necessary to put it in the reader), press the brake pedal for vehicles withan electronic or automatic gearbox, or fully declutch for vehicles with a manual
gearbox.
For Diesel vehicles, intemperatures below zero theengine will not star t until thepreheater warning lamp hasgone off. If this warning lamp comes onafter pressing "STA R T/STOP", you should hold the brake or clutch pedal down until thewarning lamp goes off and donot press the START/STOP button again.

Starting the engine
If one of the star ting conditions is not met, a reminder message appears inthe instrument panel screen. In somecircumstances, it is necessary to turn the steering wheel slightly while pressing the "STA R T/STOP" button to assist unlocking of the steering; a message warns you when this is needed.
)
Briefly press the " START/STOP"button.
The steering column locks and
the engine star ts more or less
instantly (see the advice for
Diesel versions).
The presence in the defined zone of theelectronic key for the "Keyless Entry and Starting" system is essential. For safety reasons, do not leave this zone with the vehicle running.


If the electronic key is not detected in the zone, a message is displayed. Movethe electronic key into the zone so thatthe engine can be started.

138
Driving
Emergency starting

When the electronic key is in the defined zone
and your vehicle does not star t after pressing
the "STA R T/STOP" button: ) Place the gear selector at N
for vehicles
with an electronic gearbox, P or N
for
vehicles with an automatic gearbox or
neutral
for vehicles with a manual gearbox.
) With the electronic key inside
the vehicle, press the " START/
STO
P " button.
The engine stops and the steering column locks.
)Immobilise the vehicle. )Place the gear selector lever at Nfor
vehicles with an electronic gearbox, Por Nwith an automatic gearbox, or neutral with
a manual gearbox.
Switching off the engine

If the vehicle is not immobilised, the engine will not stop.

Do not leave your vehicle with theelectronic key still inside.
)Inser t the electronic key in the reader.)Press the brake pedal on vehicles with anelectronic or automatic gearbox, or fully
declutch with a manual gearbox.)Press the "STA R T/STOP" button.
The engine starts.

139
4
Driving
Electronic key not
recognised
If the electronic key is no longer in the definedzone when driving or when you (later) request
switching off the engine, a message appears in
the instrument panel.
) Press and hold the "STA R T/STOP" button for about3 seconds if you want to forceswitching off the engine (note
that restarting will not be possible without the key ).

y

Emergency switch- off
In the event of an emergency only,
the engine can be switched of withoutconditions. To do this, press and hold
the "STA R T/STOP" button for about3 seconds.

In this case the steering column locks as soon
as the vehicle stops.

140
Driving














Ignition on without
starting


With the ignition on, the system goes into energy economy mode whennecessary to maintain the state of charge of the battery. With the electronic key in the reader or the
Keyless Entry and Starting key inside the
vehicle, pressin
g the "START/STOP" button,
with no action on the pedals
, allows the
ignition to be switched on.
)
Press the "START/STOP" button,the instrument panel comes onbut the engine does not star t.
)Press the button again to switch off the ignition and so allow the vehicle to belocked.












Anti-theft protection


Electronic engine immobiliser

The keys contain an electronic chip which has
a secret code. When the ignition is switched
on, this code must be recognised in order for
starting to be possible.
This electronic engine immobiliser locks the
engine management system a few minutes
after the ignition is switched off and prevents
starting of the engine by anyone who does not
have the key.
In the event of a malfunction, you are informedby a message in the instrument panel screen.
In this case, your vehicle does not start; contact
a CITROËN dealer as soon as possible.

141
4
Driving








Electric parking brake


In the event of a battery failure, theelectric parking brake no longer works.

As a safety measure, if the parking brake is not applied, immobilise thevehicle by engaging a gear or placing achock at one of the wheels. Contact a CITROËN dealer or a qualified workshop.
Indicator lamp

This indicator lamp comes on in theinstrument panel and in the control
lever to con
firm the application of the
parking brake.

The s
ystem provides, in automatic operation,
the application of the parking brake onswitching off the engine and release as the
vehicle moves off.
The driver can take over at any time to apply
or release the parking brake, by operating thecontrol lever:


- by briefly pullingthe control lever to applythe brake,

- by briefly pushing
the control lever, while pressing the foot brake, to release.
Automatic mode is activated by default.


The technology adopted for the electric
parking brake does not allow the fitmentof wheels smaller than 16 inches.It
goes off to confirm the release of the parkingbrake.
The indicator lamp in the control lever flashes
durin
g manual application or release.
After the parking brake has been applied, the
simultaneous flashing of the two indicator lamps in the instrument panel and the control lever alerts you to the need to fully secure your
vehicle by engaging a gear (with a manual
or electronic gearbox) or by placing the gear
selector in position P with an automatic
gearbox, or by fitting a chock to one of the wheels. (E.g. : parking on a very steep slope or
on a slope with a low battery).

142
Driving
Label on door panel
Before leaving the vehicle, check thatparking brake is applied: the indicator lamps in the instrument panel andthe control lever must be on fixed, not flashing.
If the parking brake is not applied, there is an audible signal and a message isdisplayed on opening the driver's door.


Never leave a child alone inside thevehicle with the ignition on, as theycould release the parking brake.
When towing, parking on a steepslope, or if your vehicle is heavilyladen, turn the wheels towards the kerb and engage a gear (with a manual or electronic gearbox) or place the gear selector in position P
with an automaticgearbox).For towing, you vehicle is approved for parking on slopes of up to 12%.


Manual operation


Application of of the parking brake
is confirmed by illumination of the
brake indicator lamp and the Pindicator lamp in the control lever,
accompanied by the display of the
message "Parking brake applied".

Manual release

With the ignition on or the engine running, to
release the parking brake: )press the brake pedal, )while maintaining pressure on the brakepedal, briefly push the control lever.
The complete release o
f the parking brake is confirmed by the brake indicator lamp and thePindicator lamp in the control lever going off,
accompanied by the display of the message
"Parking brake released".


If you push the control lever withoutpressing the brake pedal, the parkingbrake will not be released and a message is displayed.


Manual application

With the vehicle stationary: briefly pull the control lever.

Confirmation of the instruction is signaled by
flashing of the indicator lamp in the control
lever.

143
4
Driving
With the vehicle stationary, the parking brakeis automatically applied when the engine is switched offby pressing the START/STOP fbutton.

Application o
f of the parking brake
is confirmed by illumination of the
brake indicator lamp and the Pindicator lamp in the control lever, accompanied by the display of the message "Parking brake applied".

With the engine stalled or in STOP mode of Stop & Star t, automatic application does not take place.


In automatic mode, you can manuallyapply or release the parking brake using the control lever.


Automatic operation


Automatic release


The complete release of the parkingbrake is confirmed by the brake
indicator lamp and the P indicator
lamp in the control lever going off,
accompanied by the display of the
message "Parking brake released".
When stationary with the engine running, do notdepress the accelerator pedal unnecessarily,you risk releasing the parking brake.
Ensure first that the engine is running and the
driver's door is properly closed.
The electric parkin
g brake releases automatically and progressivelywhen youpress the accelerator: )Manual gearbox: fully depress the clutchpedal, engage 1 st
or reverse gear; press
the accelerator pedal and let up the clutch pedal. )Automatic gearbox: select position D , Mor Rthen press the accelerator. )Electronic gearbox: select position A, Mor Rthen press the accelerator pedal.



Automatic application