air Citroen XSARA PICASSO 2004 1.G Repair Manual

Downloaded from www.Manualslib.com manuals search engine 311
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS PRECAUTIONS: MA PILOTED MANUAL GEARBOX
Engines: HFX KFV NFU 8HX
Engaging of «N», without using a diagnostic tool (continued).
Preliminary operation:
Disconnect the battery negative terminal.
Remove the air filter.
Use a
22 mmspanner.
Use the spanner to lift the gear engagement lever the maximum possible until
the axis
«A»of the engagement lever is perpendicular to the axis «B»(mid
point of the gear engagement lever).
When this position is attained, position
«N»is engaged.
B2CP3L8D
C2

Downloaded from www.Manualslib.com manuals search engine 318
CLUTCH
GEARBOX
TRANSMISSION
BE4/5 GEARBOX
Engines: NFV 6FZ RFN RFS 8HV 8HY 9HZ 9HY WJY RHY RHZ
(1)Drain plug.
(2)Filling and topup plug.
(3)Air vent.
NOTE:The air vent aperture can be used for filling.
Quality of oil.Refer to the manufacturer’s instructions.
Quantity of oil.Gearbox empty:1,9 Litres.
After draining:2 Litres.
B2CP3BLD
C3 XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 330
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Tools.
[1] Tool for positioning the gear lever: 9607T.
Adjustements.
WARNING: Cables should be adjusted each
time the gearbox, gear controls or power unit
are removed.
Inside the vehicle:
Remove the trim under the gear lever.
Lock the gear lever in neutral position,
using tool
[1].
Under the bonnet: Remove the air filter assembly.
Unlock the balljoint keys at «a».
Place the gear selection and control levers on
neutral.
Lock the cable lengths with the balljoint locking
keys.
Checks.
Remove the tool [1].
Check that all the gears engage without
«tightness ».
Check that the gear lever moves identically
forwards and backwards and to right and left. If it
does not, repeat the adjustment.
Refit the trim under the gear lever.
Refit the air filter assembly.
Adjusting the gear controls Engines: NFV 6FZ RFN RFS WJY 8HZ 9HZ 9HY RHY RHZ
XSARA XSARA PICASSO
B2CP3C6CB2CP3C0C

Downloaded from www.Manualslib.com manuals search engine 331
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS PRECAUTIONS: AL4 AUTOMATIC GEARBOX
Engines: KFV NFU RFN RHZ
If a gearbox malfunction occurs, there are two possible
configurations depending on the seriousness of the fault:
Gearbox in backup mode with a replacement programme of
(the
fault values are taken in substitution).
Gearbox in backup mode with an emergency programme (3rd
hydraulic).WARNING:In the emergency programme, an impact is felt
when changing P/R, N/R and N/D.
Réception client.
Discuss with the customer, to find out all the malfunction symptoms.Oil quality Oil level.
Oil quality.
If the gearbox has suffered a serious fault resulting in a malfunction
or the destruction of a clutch, the oil will overheat and become
contaminated with impurities: the oil is said to be
«burnt».
This is characterised by a black colour and the presence of an
unpleasant smell.
ESSENTIAL: The gearbox must be replaced.
Oil level (see corresponding operation).
An excessive oil level can result in the following consequences:
Excessive heating of the oil.
Oil leaks.
An insufficent level causes the destruction of the gearbox.
Top up the level of oil in the gearbox (if necessary).
Check using a diagnostic tool.
Read the fault codes
(engine and gearbox).
Absence of fault codes.Carry out parameter measures, actuator tests and a road test.
Presence of fault codes.Carry out the necessary repairs.
Delete the fault codes.
Carry out a road test to check the repair and, if need be, modify the
gearbox ECU parameters
(this is essential after an initialisation
of the ECU).
XSARA XSARA PICASSO
Procedure to be followed prior to carrying out repairs on AL4 autoactive gearbox

Downloaded from www.Manualslib.com manuals search engine 332
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS PRECAUTIONS: AL4 AUTOMATIC GEARBOX
Engines: KFV NFU RFN RHZ
Precautions to be taken.
Towing.
The front of the vehicle must be raised in order to be towed.
If the front of the vehicle cannot be raised:
IMPERATIVE: Put gear lever in position «N».
Do not add any oil.
Do not exceed
30 mphover a distance of 30 milesof maximum.
Driving.
Never drive with the ignition switched off.
Never push the vehicle to try to start it
(impossible with an automatic gearbox).
NOTE:The automatic gearbox is only lubricated when the engine is
running.
Repairs on electrical components.
Do not disconnect:
The battery when the engine is running.
The ECU when the ignition is switched on.
Before reconnecting a switch,check: The condition of the various contacts (for deformation, corrosion etc).
The presence and condition of the mechanical locking.
When performing electrical checks: The battery should be correctly charged.
Never use a voltage source higher than 16V.
Never use a test lamp.
C3 XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 333
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS PRECAUTIONS: AL4 AUTOMATIC GEARBOX
Engines: KFV NFU RFN RHZ
Precautions to be taken.
Repairs on mechanical components.
Never place the gearbox on the ground without protection.
In order to avoid breaking the input shaft ring, it is
imperativethat
the converter retaining bracket should be in place when handlingthe gearbox.
It is
imperativeto use the centring peg and the converter retaining
bracket to couple the gearbox on the engine.
After coupling the gearbox on the engine, remove the centring peg.
Modification of the oil usage counter value.
Exchanging the gearbox ECU:
Note down the gearbox counter value.
Transfer the value read into the the new gearbox ECU.
Exchanging the gearbox :
Initialise the oil usage counter to 0.
Draining the gearbox:
Initialise the oil usage counter(follow the diagnostic tool procedure).
C3 XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 386
AXLES
SUSPENSION
STEERING
FRONT AXLE
Evolution: Suspension arm balljoint
XSARA
Application from RPO: 7968.
New components:
Suspension arm balljoint.
Pivot.
Old fitting
ØA = 16 mm.
New fittingØA = 18 mm.
Repair requirements.
ESSENTIAL:Swapping of old and new components is forbidden.
It is permitted to fit a new pivot/balljoint assembly on one side of an old
vehicle.
Replacement Parts.
The old components are still available from Replacement Parts.
B3CP054D

Downloaded from www.Manualslib.com manuals search engine 393
AXLES
SUSPENSION
STEERING
XSARA
Steering wheel Manual steering
MANUAL STEERING SPECIFICATIONS
(a): LHD/RHD = White.
(L): Shaft length = 311 ± 1.5 mm.
(1) Steering wheel fitted with AIRBAG(according to equipment).
(4)Steering column adjustment lever.
Tightening torques (m.daN).
(2) AIRBAG to steering wheel fixing: 0.8 (3)Steering wheel fixing: 3.3 (5) Steering column to support fixing:2.3 (6)Steering cardan joint fixing:2.3
(b) = Locating bush.
The locating bush must be centred in the reference window before
tightening the cardan bolts
(6).
B3EP08PD

Downloaded from www.Manualslib.com manuals search engine 396
AXLES
SUSPENSION
STEERING
XSARA POWERASSISTED STEERING SPECIFICATIONS
Steering wheel Powerassisted steering
(a): LHD = Blue.
: RHD = White.
(L): Shaft length = 311 ± 1.5 mm.
(1) Steering wheel fitted with AIRBAG(according to equipment).
(4)Steering column adjustment lever.
Tightening torques (m.daN).
(2) AIRBAGto steering wheel fixing: 0.8 (3)Steering wheel fixing: 3.3 (5)Steering column to support fixing: 2.3 (6)Steering cardan joint fixing: 2.3
(b) = Locating bush.
The locating bush must be centred in the reference
window before tightening the cardan bolts
(6).
B3EP08QD

Downloaded from www.Manualslib.com manuals search engine 407
AXLES
SUSPENSION
STEERING
STEERING COLUMN SPECIFICATIONS
Left hand drive = Greenmarking.
Right hand drive = Whitemarking.
(1) Steering wheel(4)Steering column adjustment
Tightening torques m.daN.
(2)
Airbag to steering wheel fixing: 0.8 ± 0.1
(3)Steering wheel fixing: 3.3 ± 0.6
(5)Steering column to support fixing: 4 ± 0.1
(6) Steering cardan joint fixing:2.3 ± 0.2
B3EP116D
XSARA PICASSO