Engine DAEWOO LACETTI 2004 Service Repair Manual

5A2 – 28IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
FUNCTION CHECK
Confirm whether below condition before function check.
S Oil temperature is hot condition (50°C (122°F) ~
80°C (176°F)).
S Switch of A/C and light etc are off.
Stall Test
Stall test’ purpose is to inspect overall performance of A/T
and engine by measuring the stall speed in ”D” and ”R”
range.1. Chock 4 Wheels and apply parking brake fully, lock
vehicle perfectly.
2. Fully pressed on foot brake pedal with left foot.
3. Shift into ”D” and ”R” range, fully press on accelera-
tor pedal with right foot.
Quickly read stall speed at this time.
Standards
2390 ± 150 rpm
Notice : Do not continuously run longer than 5 sec be-
cause of extreme increasing oil temp.
Make sure to keep interval for more than 1 min between
stall tests.
Result of Stall Test
Cause of Failure
Lower than standards
both ”D” and ”R”Less engine power
Torque converter one way clutch failure
Higher than standards
only ”D”Lower line pressure
S Pressure control solenoid (PCS) failure
S Primary regulator valve failure
Forward clutch (C1) failure (Slipping)
No.2 One–way clutch (F2) failure
Higher than standards
only ”R”Lower line pressure
S Pressure control solenoid (PCS) failure
S Primary regulator valve failure
Reverse clutch (C3) failure (Slipping)
1st & reverse brake (B3) failure (Slipping)
Higher than standards
both ”D” and ”R”Lower line pressure
S Pressure control solenoid (PCS) failure
S Primary regulator valve failure
Oil pump failure
Oil strainer failure (clogging)
Oil leak for each range circuit
Time Lag Test
Time lag is time till slightly shock can be felt when shift le-
ver is shifted ”N”  ”D” and ”N”  ”R” while engine idling.
Time lag test can inspect hydraulic condition and clutch/
brake condition.
1. Chock 4 Wheels and apply parking brake fully, lock
vehicle perfectly.
2. Measure time lag by using stop watch from moment
when shift lever is shifted in ”N”  ”D” and ”N” 
”R” until moment slightly shock can be felt.”N  D”less than 0.7 sec
”N”  ”R”less than 1.2 sec
Notice : Make sure to take 3 measurement and take the
average value.
Make sure to keep interval for more than 1 min between
time lag tests. (That purpose is to remove clutch/brake
pressure was left unfinished.)

AISIN AUTOMATIC TRANSAXLE 5A2 – 29
DAEWOO V–121 BL4
Result of Time Lag TestCause of Failure
Longer than standards ”N”  ”D”Lower line pressure
S Pressure control solenoid (PCS) failure
S Primary regulator valve failure
Forward Clutch (C1) failure (Slipping)
Timing solenoid failure
Oil leak for ”D” range circuit
Longer than standards ”N”  ”R”Lower line pressure
S Pressure control solenoid (PCS) failure
S Primary regulator valve failure
Reverse clutch (C3) failure (slipping)
1st & reverse brake (B3) failure (slipping)
Oil leak for ”R” range circuit
Hydraulic Test
Hydraulic test can inspect working condition inside A/T by
measuring line pressure in ”D” / ”R” range and ”idle” / ”stall”
condition.
1. Chock 4 Wheels and apply parking brake fully, lock
vehicle perfectly.2. Install oil pressure gage adapter DW240–010–02 to
test hole for line pressure.
3. Fully pressed on foot brake pedal with left foot, shift
into ”D” and ”R” range and measure line pressure
”idle” / ”stall” condition.
Line pressure
Mpa (kgf/cm
2)
DR
Engine idle0.37 (3.9)
–0.14 (4.2)0.59 (6.0)
–0.68 (6.9)
Engine stall1.10 (11.3)
–1.23 (12.5)1.58 (16.2)
–1.83 (18.6)
Notice : Do not continuously run longer than 5 sec be-
cause of extreme increasing oil temp.
Make sure to keep interval for more than 1 min between
stall tests.
Make sure to check no oil leak after installing oil pressure
gage adapter.
Result of Hydraulic Test
Cause of Failure
Higher than standards
both ”D and ”R”Pressure control solenoid (PCS) failure
Primary regulator valve failure
Lower than standards
both ”D and ”R”Pressure control solenoid (PCS) failure
Primary regulator valve failure
Oil pump failure
Oil strainer failure (clogging)
Oil leak for each range circuit
Lower than standards
only ”D”D” hydraulic circuit failure
Forward clutch (C1) failure
Lower than standards
only ”R””R” hydraulic circuit failure
Reverse clutch (C3) failure
1st and reverse brake (B3) failure

5A2 – 36IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE DIAGNOSIS
DIAGNOSTIC TROUBLE CODE CHART
DTCDESCRIPTIONTYPEIlluminate
MILBlink
Hold
Lamp
P0562System Voltage LowBYe sNo
P0563System Voltage HighBYe sNo
P0601Internal Control Module Memory Checksum ErrorAYe sNo
P0604Internal Transmission Control Module (TCM) Random Access
Memory (RAM) ErrorBYe sNo
P0705Transmission Range (TR) Switch Circuit MalfunctionBYe sNo
P0712Transmission Fluid Temperature Sensor Circuit Low InputAYe sNo
P0713Transmission Fluid Temperature Sensor Circuit High InputAYe sNo
P0717Input Shaft Speed (ISS) Sensor Circuit No SignalAYe sNo
P0722Output Shaft Speed (OSS) sensor Circuit No SignalAYe sNo
P0727Engine Speed Input Circuit No SignalAYe sNo
P0741Torque Converter Clutch (TCC) Circuit Stuck OffBYe sNo
P0742Torque Converter Clutch (TCC) Circuit Stuck OnBYe sNo
P0743Torque Converter Clutch (TCC) ElectricalBYe sNo
P0748Pressure Control Solenoid (PCS) ElectricalAYe sNo
P0751Shift Solenoid 1 (SS1) Stuck OffBYe sNo
P0753Shift Solenoid 1 (SS1) ElectricalAYe sNo
P0756Shift Solenoid 2 (SS2) Stuck OffBYe sNo
P0758Shift Solenoid 2 (SS2) ElectricalAYe sNo
P0785Timing Solenoid (ST) ElectricalAYe sNo
P1781Engine Torque Signal ErrorAYe sNo
P1791Throttle Position Signal ErrorAYe sNo
P1792Engine Coolant Temperature (ECT) Signal ErrorDNoNo
U2105CAN ErrorAYe sNo
* Description of Type
S Type A : TCM will request the illumination of MIL and store DTC when TCM detects a failure on the first ignition
cycle.
S Type B : TCM will request the illumination of MIL and store DTC when TCM detects failures on two consecutive
ignition cycle.
S Type D : TCM will not request the illumination of MIL or hold lamp, but will store DTC when TCM detects a failure
on the first ignition cycle.

AISIN AUTOMATIC TRANSAXLE 5A2 – 37
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0562
SYSTEM VOLTAGE LOW
Conditions for Setting the DTC
S System voltage is too low.
S TCM detects that voltage is less than 9 volts for 0.5
seconds continuously.
S Engine revolution is 600 rpm or greater.
Action Taken When the DTC Sets
S TCM will request the illumination of MIL and store
DTC when TCM detects failures on two consecu-
tive ignition cycle.
Conditions for Clearing the DTCS The TCM turns off the MIL when no further failures
detected for three consecutive ignition cycles.
S The scan tool can clear the DTC from the TCM his-
tory.
S The TCM clears the DTC from the TCM history
memory after forty consecutive warm up cycles
without fault.
Cause of Failure
S TCM wiring harness and connectors
S Battery
S TCM

5A2 – 38IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DTC P0562 System Voltage Low
StepActionValue(s)YesNo
11. Turn the ignition OFF.
2. Install the Scan tool.
3. Turn the ignition ON, with the engine OFF.
4. Run the engine to 600 rpm or greater.
5. Record then clear DTC(s).
6. Select system voltage on the scan tool.
7. Drive the vehicle and observe the scan tool for
either of the flowing conditions:
Is the voltage within the values shown?9–16vGo to Step 4Go to Step 2
21. Disconnect the battery cable.
2. Measure the battery voltage.
Is the voltage within the values shown?9–16vGo to Step 4Go to Step 3
31. Replace the battery.
Is the replacement completed?–System OK–
41. Turn the headlamp ON.
2. Turn the air conditioner ON.
3. Run the engine to 600 rpm or greater.
4. Observe the scan tool for system voltage.
Is the voltage within the values shown?9–16vGo to Step 6Go to Step 5
51. Turn the ignition LOCK.
2. Repair the alternator circuit if necessary.
Is the action completed?–System OK–
6Inspect the EF1,F2 fuse for an open.
Was a problem found?–Go to Step 7Go to Step 8
7Inspect the EF1,F2 fuse for short. Replace the fuse
if necessary.
Is the replacement complete?–System OK–
81. Turn the ignition ON.
2. Measure the voltage of EF1, F2.
Is the voltage within the values shown?9–16vGo to Step 10Go to Step 9
9Repair the fuse voltage supply lines for open.
Is the action completed?–System OK–
101. Turn the ignition LOCK.
2. Disconnect the TCM wiring connector.
3. Measure the resistance between EF1 fuse and
terminal A24 of the TCM wiring connector.
Is the resistance within the values shown?0ΩGo to Step 12Go to Step 11
11Repair the circuit (between EF1 and terminal A24)
for short to ground and open.
Is the repair completed?–System OK–
121. Disconnect the C105 connector and TCM con-
nector.
2. Turn the ignition ON.
3. Measure the voltage of the terminal A24.
Is the voltage within the values shown?9–16vGo to Step 13Go to Step 14
13Repair the circuit from EF1 to terminal A24 of the
TCM for short to battery.
Is the repair completed?–System OK–

5A2 – 40IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0563
SYSTEM VOLTAGE HIGH
Conditions for Setting the DTC
S System voltage is too high.
S TCM detects that voltage is greater than 18 volts
for 0.5 seconds continuously.
S Engine revolution is 600 rpm or greater.
Action Taken When the DTC Sets
S TCM will request the illumination of MIL and store
DTC when TCM detects failures on two consecu-
tive ignition cycle.
Conditions for Clearing the DTCS The TCM turns off the MIL when no further failures
detected for three consecutive ignition cycles.
S The scan tool can clear the DTC from the TCM his-
tory.
S The TCM clears the DTC from the TCM history
memory after forty consecutive warm up cycles
without fault.
Cause of Failure
S TCM wiring harness and connectors
S Battery
S TCM

AISIN AUTOMATIC TRANSAXLE 5A2 – 41
DAEWOO V–121 BL4
DTC P0563 System Voltage High
StepActionValue(s)YesNo
11. Turn the ignition OFF.
2. Install the Scan tool.
3. Turn the ignition ON, with the engine OFF.
4. Run the engine to 600 rpm or greater.
5. Record then clear DTC(s).
6. Select system voltage on the scan tool.
7. Drive the vehicle and observe the scan tool for
either of the flowing conditions:
Is the voltage within the values shown?9–16vGo to Step 4Go to Step 2
21. Disconnect the battery cable.
2. Measure the battery voltage.
Is the voltage within the values shown?9–16vGo to Step 4Go to Step 3
31. Replace the battery.
Is the replacement completed?–System OK–
41. Turn the headlamp ON.
2. Turn the air conditioner ON.
3. Run the engine to 600 rpm or greater.
4. Observe the scan tool for system voltage.
Is the voltage within the values shown?9–16vGo to Step 6Go to Step 5
51. Turn the ignition LOCK.
2. Repair the alternator circuit if necessary.
Is the action completed?–System OK–
6Inspect the EF1,F2 fuse for an open.
Was a problem found?–Go to Step 7Go to Step 8
7Inspect the EF1,F2 fuse for short. Replace the fuse
if necessary.
Is the replacement complete?–System OK–
81. Turn the ignition ON.
2. Measure the voltage of EF1,F2.
Is the voltage within the values shown?9–16vGo to Step 10Go to Step 9
9Repair the fuse voltage supply lines for open.
Is the action completed?–System OK–
101. Turn the ignition LOCK.
2. Disconnect the TCM wiring connector.
3. Measure the resistance between EF1 fuse and
terminal A24 of the TCM wiring connector.
Is the resistance within the values shown?0ΩGo to Step 12Go to Step 11
11Repair the circuit (between EF1 and terminal A24)
for short to ground and open.
Is the repair completed?–System OK–
121. Disconnect the C105 connector and TCM con-
nector.
2. Turn the ignition ON.
3. Measure the voltage of the terminal A24.
Is the voltage within the values shown?9–16vGo to Step 13Go to Step 14
13Repair the circuit from EF1 to terminal A24 of the
TCM for short to battery.
Is the repair completed?–System OK–

5A2 – 44IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DTC P0601 Internal Control Module Memory Checksum Error
StepActionValue(s)YesNo
11. Turn the ignition OFF.
2. Install the Scan tool.
3. With the engine OFF, turn the ignition switch to
the ON position.
4. Select Store Freeze Frame/Failure Records
from the Diagnostic Trouble Codes Information
menu.
5. Store Freeze Frame/Failure Records.
6. Select Clear DTC Information from the Diag-
nostic Trouble Codes Information menu.
7. Clear DTC Information.
8. Perform one vehicle drive cycle.
Is the Malfunction Indicator Lamp (MIL) ON?–Go to Step 2Inspect Trans-
mission Control
Module (TCM)
wiring harness
and connector
for signs of an
intermittent
condition. Re-
pair as neces-
sary.
21. Select Request DTC by Status from the Diag-
nostic Trouble Codes Information menu.
2. Request DTC by Status.
Is DTC P0601 displayed?–Replace the
Transmission
Control Module
(TCM)Inspect Trans-
mission Control
Module (TCM)
wiring harness
and connector
for signs of an
intermittent
condition. Re-
pair as neces-
sary.

5A2 – 46IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DTC P0604 Internal Transmission Control Module (TCM) Random
Access Memory (RAM) Error
StepActionValue(s)YesNo
11. Turn the ignition OFF.
2. Install the Scan tool.
3. With the engine OFF, turn the ignition switch to
the ON position.
4. Select Store Freeze Frame/Failure Records
from the Diagnostic Trouble Codes Information
menu.
5. Store Freeze Frame/Failure Records.
6. Select Clear DTC Information from the Diag-
nostic Trouble Codes Information menu.
7. Clear DTC Information.
8. Perform two vehicle drive cycles.
Is the Malfunction Indicator Lamp (MIL) ON?–Go to Step 2Inspect Trans-
mission Control
Module (TCM)
wiring harness
and connector
for signs of an
intermittent
condition. Re-
pair as neces-
sary.
21. Select Request DTC by Status from the Diag-
nostic Trouble Codes Information menu.
2. Request DTC by Status.
Is DTC P0604 displayed?–Replace the
Transmission
Control module
(TCM)Inspect Trans-
mission Control
Module (TCM)
wiring harness
and connector
for signs of an
intermittent
condition. Re-
pair as neces-
sary.

AISIN AUTOMATIC TRANSAXLE 5A2 – 47
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0705
TRANSMISSION RANGE (TR) SWITCH CIRCUIT
MALFUNCTION
Conditions for Setting the DTC
S TCM detects more than two equal signals from the
Park/Neutral Position switch circuit for 10 seconds
continuously.
S TCM detects the no signal of TR switch circuit for 2
seconds continuously.
S Vehicle speed is 30 km/h (19 mph) or greater.
S Engine revolution is 1500 rpm or greater.
Action Taken When the DTC Sets
S TCM will request the illumination of MIL and store
DTC when TCM detects failures on two consecu-
tive ignition cycle.
S TCM judges with the priority. (D>2>1>R>N>P)
S No timing solenoid control for N–D
S No self–learning control
S No lockupS No prevent reverse gear control
Conditions for Clearing the DTC
S The TCM turns off the MIL when no further failures
detected for three consecutive ignition cycles.
S The scan tool can clear the DTC from the TCM his-
tory.
S The TCM clears the DTC from the TCM history
memory after forty consecutive warm up cycles
without fault.
S TCM detects single ”D range” signal of the TR
switch.
Cause of Failure
S Wiring harness or connector between TR switch
and TCM
S TR switch
S TCM