tire size DODGE DURANGO SRT 2019 Vehicle Warranty

Page 21 of 270

authorized tire dealer for recommended safe operating speeds, loading
and cold tire inflation pressures.
While studded tires improve performance on ice, skid and traction
capability on wet or dry surfaces may be poorer than that of non-studded
tires. Some states prohibit studded tires; therefore, local laws should be
checked before using these tire types.
Spare Tires — If Equipped
NOTE:For vehicles equipped with Tire Service Kit instead of a spare tire,
please refer to “Tire Service Kit” in “In Case Of Emergency” in your
Owner ’s Manual for further information.
CAUTION!
Because of the reduced ground clearance, do not take your vehicle
through an automatic car wash with a compact or limited use
temporary spare installed. Damage to the vehicle may result.
Spare Tire Matching Original Equipped Tire And Wheel — If
Equipped
Your vehicle may be equipped with a spare tire and wheel equivalent in
look and function to the original equipment tire and wheel found on the
front or rear axle of your vehicle. This spare tire may be used in the tire
rotation for your vehicle. If your vehicle has this option, refer to an
authorized tire dealer for the recommended tire rotation pattern.
Compact Spare Tire — If Equipped
The compact spare is for temporary emergency use only. You can identify
if your vehicle is equipped with a compact spare by looking at the spare
tire description on the Tire and Loading Information Placard located on
the driver ’s side door opening or on the sidewall of the tire. Compact
spare tire descriptions begin with the letter “T” or “S” preceding the size
designation. Example: T145/80D18 103M.
T, S = Temporary Spare Tire
Since this tire has limited tread life, the original equipment tire should be
repaired (or replaced) and reinstalled on your vehicle at the first
opportunity.
Do not install a wheel cover or attempt to mount a conventional tire on
the compact spare wheel, since the wheel is designed specifically for the
TIRES
20

Page 23 of 270

Full Size Spare — If Equipped
The full size spare is for temporary emergency use only. This tire may
look like the originally equipped tire on the front or rear axle of your
vehicle, but it is not. This spare tire may have limited tread life. When the
tread is worn to the tread wear indicators, the temporary use full size
spare tire needs to be replaced. Since it is not the same as your original
equipment tire, replace (or repair) the original equipment tire and
reinstall on the vehicle at the first opportunity.
Limited Use Spare — If Equipped
The limited use spare tire is for temporary emergency use only. This tire
is identified by a label located on the limited use spare wheel. This label
contains the driving limitations for this spare. This tire may look like the
original equipped tire on the front or rear axle of your vehicle, but it is
not. Installation of this limited use spare tire affects vehicle handling.
Since it is not the same as your original equipment tire, replace (or repair)
the original equipment tire and reinstall on the vehicle at the first
opportunity.
WARNING!
Limited use spares are for emergency use only. Installation of this
limited use spare tire affects vehicle handling. With this tire, do not
drive more than the speed listed on the limited use spare wheel.
Keep inflated to the cold tire inflation pressures listed on your Tire
and Loading Information Placard located on the driver ’s side B-Pillar
or the rear edge of the driver ’s side door. Replace (or repair) the
original equipment tire at the first opportunity and reinstall it on
your vehicle. Failure to do so could result in loss of vehicle control.
TIRES22

Page 33 of 270

For Example Only:
Gauge reading of hot tire:................................ 32 psi (220 kPa)
If recommended cold inflation pressure is: ............. 30 psi (205 kPa)
Desired gauge reading of hot tire 3 0+4psi=........
34 psi (205 + 30 = 235 kPa)
Therefore: add 2 psi ....................................... (15 kPa)
Check cold pressure as soon as possible, preferably within 24 hours.
“Bleeding” air from hot tires could result in under-inflation. Use an
accurate tire gauge to check pressures. Never allow children to inflate
or deflate tires.
TIRE PRESSURE MONITORING SYSTEMS (TPMS):
Your vehicle may be equipped with a Tire Pressure Monitoring System
(TPMS) that is designed to monitor the pressure of tires mounted on your
vehicle and sends a signal to the driver if a tire pressure falls below a
predetermined level. A TPMS should not replace monthly manual
pressure checks for all four (4) tires and the spare. We recommend that
you manually monitor and check tire pressure inflation with a pressure
gauge.
Your tires should have the recommended pressure listed by your
vehicle’s manufacturer. This information can be found in the vehicle
owner ’s manual and often on a placard located in the vehicle’s door
jamb, inside the fuel hatch, or on the glove compartment door. If you
have a plus size fitment that requires a higher inflation pressure, your tire
pressure monitoring system will require re-calibration to the new infla-
tion pressure. Refer to your tire dealer/installer of plus size tires for
proper inflation pressure.
We recommend checking air pressure once each month, and before a long
trip. Whether you have a full-sized or mini-spare, make sure that it is
properly inflated as well. If the TPMS generates improper monitoring or
signals we recommend that you consult your owner ’s manual provided
with your vehicle and follow-up with your vehicle’s manufacturer.
BFGOODRICH TIRES
32

Page 38 of 270

The maximum load rating of your tires is molded on the tire sidewall. Do
not exceed this rating. Follow the loading instructions of the manufac-
turer of your vehicle and this will ensure that your tires are not
overloaded. Tires which are loaded beyond their maximum allowable
loads for the particular application will build up excessive heat that may
result in sudden tire destruction.
Do not exceed the gross axle weight rating for any axle on your vehicle.
TRAILER TOWING
If you anticipate towing a trailer, you should visit any BFGoodrich® tire
retailer for advice concerning the correct size tire and pressures. Tire size
and pressures will depend upon the type and size of trailer and hitch
utilized, but in no case must the maximum cold inflation pressure or tire
load rating be exceeded. Check the tire decal and the owner ’s manual
supplied by the manufacturer of your vehicle for further recommenda-
tions on trailer towing.
WHEEL ALIGNMENT AND BALANCING ARE IMPORTANT FOR
SAFETY AND MAXIMUM MILEAGE FROM YOUR TIRES CHECK
HOW YOUR TIRES ARE WEARING AT LEAST ONCE EACH
MONTH
If your tires are wearing unevenly, such as the inside shoulder of the tire
wearing faster than the rest of the tread, or if you detect excessive
vibration, your vehicle may be out of alignment or balance. These
conditions not only shorten the life of your tires but adversely affect the
handling characteristics of your vehicle, which could be dangerous. If
you detect irregular wear or vibration, have your alignment and balance
checked immediately. Tires which have been run underinflated will show
more wear on the shoulders than in the center of the tread.
TIRE MIXING
BFGoodrich® tires are radial tires and for best performance it is recom-
mended that the same size and type of tire be used on all four wheel
positions. Before mixing tires of different types in any configuration on
any vehicle, be sure to check the vehicle manufacturer ’s Owner‘s Manual
for its recommendations.
It is especially important to check the vehicle manufacturer ’s owner ’s
manual when mixing, matching or replacing tires on 4-wheel drive
vehicles, as this may require special precautions.
BFGOODRICH TIRES
37

Page 39 of 270

BFGOODRICH® DOES NOT RECOMMEND MIXING SELF SUPPORT-
ING STRUCTURE (SSS) TIRES WITH NON-SSS TIRES OTHER THAN
THE TEMPORARY USE OF THE SPARE TIRE.
WINTER DRIVING
Tires which meet the Rubber manufactures Association (RMA) definition
of snow tires are marked M/S, M&S. On such tires, this designation is
molded into the sidewall. Tires without this notation are not recom-
mended for winter driving.While All-Season tires are designed to provide reliable
performance in some winter conditions, the use of four
(4) winter tires is recommended for optimum perfor-
mance. Tires designated for use in severe winter condi-
tions are marked on at least one sidewall with the letter
“M” and “S” plus a pictograph of a mountain with a snowflake on it.
TIRE ROTATION AND REPLACEMENT
To obtain maximum tire wear, it may be necessary to rotate your tires. Refer
to your vehicle owner ’s manual for instructions on tire rotation. If you do
not have an owner‘s manual for your vehicle, BFGoodrich® recommends
rotating your tires every 6,000 to 8,000 miles (10,000 to 12,000 km).
Monthly inspection for tire wear is recommended. Your tires should be
rotated at the first sign of irregular wear, even if it occurs before 6,000
miles (10,000 km). This is true for all vehicles.
When rotating tires with a directional tread pattern, observe the arrows
molded on the sidewall which show the direction the tire should turn.
Care must be taken to maintain the proper turning direction.
Some Tire Pressure Monitoring systems (TPMS) may not recognize that a
tire has been moved to a different position on your vehicle. Make certain
that your TPMS system is reset, if necessary, so as to correctly identify the
location of each tire on your vehicle. Refer to your vehicle owner ’s
manual or your vehicle dealer.
Determine whether rotated tires require tire inflation adjustment as front
and rear position tire pressure may vary according to the vehicle manufac-
turer ’s specification due to the actual load on that wheel position. Some
vehicles may have different sized tires mounted on the front and rear axles,
and these different sized tires have rotation restrictions. Always check the
vehicle owner ’s manual for the proper rotation recommendations.
BFGOODRICH TIRES
38

Page 40 of 270

FULL-SIZE SPARE
Full-size spare tires (not temporary spares) of the same size and construc-
tion should be used in a five (5) tire rotation. Always check the inflation
pressure of the full-size spare immediately before incorporating it into
rotation. Follow the vehicle manufacturer ’s recommended pattern for
rotation, or if not available, see a qualified tire technician.
REPLACEMENT OF TWO (2) TIRES
It is recommended that all four (4) tires are replaced at the same time.
However, whenever only two tires are replaced, the new ones should be
put on the rear. The new tires, with deeper tread, may provide better grip
and water evacuation in wet driving conditions.
CUSTOMIZATION OF TIRES, WHEELS, OR SUSPENSION ON
SUVS AND LIGHT TRUCKS
Due to their size, weight and higher center of gravity, vehicles such as
SUVs and light trucks do not have the same handling characteristics as
automobiles. Because of these differing characteristics, failure to operate
your SUV/truck in a proper and safe manner can increase the likelihood
of vehicle rollover. Modifications to your SUV/truck tire size, tire type,
wheels or suspension can change its handling characteristics and further
increase the likelihood of vehicle rollover. Whether your SUV/truck has
the original equipment configuration for tires, wheels and suspension or
whether any of these items have been modified, always drive safely,
avoid sudden, sharp turns or lane changes and obey all traffic laws.
Failure to do so may result in loss of vehicle control leading to an accident
and serious injury or death.
TIRE ALTERATIONS
Do not make or allow to be made any alterations on your tires.
Alterations may prevent proper performance, leading to tire damage
which can result in an accident. Tires which become unserviceable due to
alterations such as trueing, whitewall inlays, addition of balancing or
sealant liquids, or the use of tire dressing containing petroleum distillates
are excluded from warranty coverage.
BFGOODRICH TIRES
39

Page 42 of 270

reflect the tire size. The following one to four digits may be used at the
tire manufacturer ’s option as a descriptive code. The last three characters
are numbers identifying the week and year of manufacture. (Example:
“O25” means second week of the year of decade, eg.: 1995, 1985, etc.)
Tires produced after July 2000 have an additional digit to identify a given
decade. For example, 2800 means the tire was produced during the 28th
week of 2000; 0201 during the 2nd week of 2001. If the last digits of your
DOT number contain three numeric characters consult a qualified tire
technician to determine the year and decade of manufacture.
STORAGE
Tires contain waxes and emollients to protect their outer surfaces from
ozone and weather checking. As the tire rolls and flexes, the waxes and
emollients continually migrate to the surface, replenishing this protection
throughout the normal use of the tire. Consequently, when tires sit
outdoors, unused for long periods of time (a month or more) their
surfaces become dry and more susceptible to ozone and weather check-
ing and the casing becomes susceptible to flat spotting.
For this reason, tires should always be stored in a cool, dry, clean,
indoor environment. If storage is for one month or more, eliminate the
weight from the tires by raising the vehicle or by removing the tires
from the vehicle. Failure to store tires in accordance with these
instructions could result in damage to your tires or premature aging of
the tires and sudden tire failure.
When tires are stored, be sure they are placed away from sources of heat
and ozone such as hot pipes and electric generators. Be sure that surfaces
on which tires are stored are clean and free from grease, gasoline or other
substances which could deteriorate the rubber.(Tires exposed to these
materials during storage or driving could be subject to sudden failure.)
FOLLOW THESE MOUNTING RECOMMENDATIONS
Tire changing can be dangerous and must be done by professionally
trained persons using proper tools and procedures as specified by the
Rubber Manufacturers Association (RMA).
Your tires should be mounted on wheels of correct size and type and
which are in good, clean condition. Wheels that are bent, chipped, rusted
(steel wheels) or corroded (alloy wheels) may cause tire damage. The
inside of the tire must be free from foreign material. Have your retailer
check the wheels before mounting new tires. Mismatched tires and rims
BFGOODRICH TIRES
41

Page 43 of 270

can explode during mounting. Also, mismatched tires and rims can result
in dangerous tire failure on the road. If a tire is mounted by error on the
wrong-sized rim, do not remount it on the proper rim - scrap it. It may
have been damaged internally (which is not externally visible) by having
been dangerously stretched and could fail on the highway.
Old valves may leak. When new tubeless tires are mounted, have new
valves of the correct type installed. Tubeless tires must only be
mounted on wheels designed for tubeless tires i.e., wheels which have
safety humps or ledges.
It is recommended that you have your tires and wheels balanced. Tires
and wheels which are not balanced may cause steering difficulties, a
bumpy ride, and irregular tire wear.
Be sure that all your valves have suitable valve caps. The valve cap is
the primary seal against air loss.
SERVICE LIFE FOR PASSENGER CAR AND LIGHT TRUCK
TIRES INCLUDING SPARE TIRES
The following recommendation applies to passenger car and light truck
tires. Tires are composed of various types of material and rubber
compounds, having performance properties essential to the proper
functioning of the tire itself. These component properties evolve over
time. For each tire, this evolution depends upon many factors such as
weather, storage conditions, and conditions of use (load, speed, inflation
pressure, maintenance etc.) to which the tire is subjected throughout its
life. This service-related evolution varies widely so that accurately
predicting the serviceable life of any specific tire in advance is not
possible.
That it is why, in addition to regular inspections and inflation pressure
maintenance by consumers, it is recommended to have passenger car and
light truck tires, including spare tires, inspected regularly by a qualified
tire specialist, such as a tire dealer, who will assess the tire’s suitability for
continued service. Tires which have been in use for 5 years or more
should continue to be inspected by a specialist at least annually.
Consumers are strongly encouraged to be aware not only of their tires’
visual condition and inflation pressure but also of any change in dynamic
performance such as increased air loss, noise or vibration, which could be
an indication that the tires need to be removed from service to prevent
tire failure.
BFGOODRICH TIRES42

Page 45 of 270

If you see any damage to your tires or wheels, contact your local
participating BFGoodrich® tire retailer listed in the Yellow Pages, or
visit our web site listed below for dealer locations. If further assistance
is required, contact:
IN USAIN CANADA
877-788-8899 888-871-4444
or write:
Michelin North America, Inc.
Attention: Consumer Relations
Department
Post Office Box 19001
Greenville, SC 29602-9001 or write:
Michelin North America (Canada), Inc.
2500 Daniel-Johnson Blvd., Suite 500
Laval, Quebec
H7P 6G2
or visit:
www.bfgoodrichtires.com or visit:
www.bfgoodrichtires.ca
WARNING!
For safety and good performance, you must take care of your tires.
Follow the safety information and instructions contained in this
Owner ’s Manual.
Your Vehicle:Year
Make/Model
Your Tire Size:
Tire Purchase Date:
Recommended Pressures: Front
Rear
Correct tire pressure is very important. Proper inflation pressures may be
found in the vehicle owner ’s manual or on the vehicle tire information
placard. Check cold tire pressures at least once each month. For further
technical information on BFGoodrich® tires, consult a participating
BFGoodrich® tire retailer.
MNA, P.O. BOX 19026, GREENVILLE, SOUTH CAROLINA 29602-9026
AN EQUAL OPPORTUNITY EMPLOYER
BFGOODRICH TIRES
44

Page 56 of 270

Maximum Pressure Indicated on the Tire Sidewall:This is the maxi-
mum permissible inflation pressure for the tire only. The vehicle manu-
facturer ’s recommended tire pressures may be lower than, or the same as,
the maximum pressure indicated on the tire sidewall. The vehicle
manufacturer ’s specification of tire pressure is limited to your particular
vehicle and takes into account your vehicle’s load, ride, and handling
characteristics, among other criteria. Since there may be several possible
vehicle applications for a given tire size, a vehicle manufacturer may
choose a different inflation pressure specification for that same size tire
on a different vehicle. Therefore, always refer to the inflation pressure
specifications on the vehicle tire information placard and/or in your
vehicle owner ’s manual.
Different Tire Pressures for the Front and Rear Tires:For some vehicles,
the recommended front and rear inflation pressures may be different
(such as in the example shown in Figure 2). Make sure you take this into
account during inflation pressure checks and when rotating tires.
Pressure Loss: Tires can lose 1 psi (7 kPa) per month under normal
conditions and can lose 1 psi (7 kPa) for every 10° F (5.6° C) temperature
drop. A puncture, leaking valve, or other damage could also cause
inflation pressure loss. If a tire loses more than 2 psi (14 kPa) per month,
have it checked by a qualified tire service professional.
Figure 2: EXAMPLE—Tire Information Placard
BRIDGESTONE® - FIRESTONE®
55

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 ... 80 next >