suspension FORD MUSTANG 2003 Repair Manual

REMOVAL AND INSTALLATION
Bushing —
Stabilizer Bar
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number or an equivalent part must be installed, if installation is necessary. Do
not use a part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to ensure correct retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assemblies. For additional information, refer to Section 204 - 04 .
3. Disconnect the front stabilizer bar links (5K483) from the front stabilizer bar (5482). 1. Remove the nuts and bushings. Discard the nuts.
2. Rotate the stabilizer bar to disconnect the links.
4. Remove and discard the nuts.
5. Remove the stabilizer bar bracket (5486) and the stabilizer bar mounting bracket adapter (5B482).
SECTION 204-
01: Front Suspension 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Cut the stabilizer bar insulators (5493) from the stabilizer bar.
Installation 1. NOTE: To aid installation, coat the necessary parts of the front stabilizer bar and the inside
diameter of the stabilizer bar bushing with Rubber Suspension Insulator Lube E25Y-19553- A or
equivalent meeting Ford specification ESF-M99B112- A.
To install, reverse the removal procedure. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Spindle
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number or an equivalent part must be installed, if installation is necessary. Do
not use a part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to ensure correct retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Remove the front wheel hub (1104). For additional information, refer to Wheel Hub and Bearing in this section.
4. Remove the bolt and the ABS sensor.
5. Unclip the ABS sensor wire from the bracket.
SECTION 204-
01: Front Suspension 2003 Mustang Workshop Manual Special Tool(s)
Tie-
Rod End Remover
211- 001 (TOOL- 3290-D) or
Equivalent Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Remove the front brake disc shield.
1. Remove the three shield rivets.
2. Remove the shield.
7. Remove the cotter pin and nut. Discard the cotter pin.
8. CAUTION: Use care not to damage the tie- rod end dust boot.
Using the special tool, disconnect the tie- rod end from the front wheel spindle.
9. CAUTION: To prevent damage to the front suspension lower arm (3078), do not
remove the nut from the ball joint (3050) at this time.
Disconnect the ball joint stud from the front wheel spindle (3105).
zLoosen the ball joint stud two or three turns.
z Sharply rap on the spindle at the ball joint connection to disconnect the ball joint stud. Klj . 2 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

10. Support the front suspension lower arm with a jack stand.
11. Remove the nut and the ABS sensor wire bracket.
12.
WARNING: All vehicles are equipped with gas pressurized shock absorbers which
will extend unassisted. Do not apply heat or flame to the shock absorbers during
removal or component servicing. Failure to follow these instructions can result in
personal injury.
Disconnect the front shock absorber (18124) from the spindle. 1. Remove and discard the nuts and bolts.
2. Disconnect the shock absorber.
13. Remove the spindle. 1. Remove and discard the nut.
2. Remove the spindle. Klj . 3 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Shock Absorber
Removal
WARNING: All vehicles are equipped with gas pressurized shock absorbers which will
extend unassisted. Do not apply heat or flame to the shock absorbers during removal or
component servicing. Failure to follow these instructions can result in personal injury.
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number or an equivalent part must be installed, if installation is necessary. Do
not use a part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to ensure proper retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Remove the front brake disc. For additional information, refer to Section 206 - 03 .
4. Remove the bolt and the ABS sensor.
5. Unclip the ABS sensor wire from the bracket.
6. Remove the nut and the ABS sensor wire bracket.
SECTION 204-
01: Front Suspension 2003 Mustang Workshop Manual Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

7. Support the front suspension lower arm (3078) with a jack stand.
8. Disconnect the shock absorber (18124) from the spindle (3105).
1. Remove and discard the nuts and bolts.
2. Disconnect the shock absorber.
9. Carefully lower the front suspension lower arm and remove the jack stand.
10. CAUTION: Do not allow the weight of the vehicle to rest on the front brake disc
shield. Damage to the shield can occur.
Lower the vehicle to access the upper mount nuts and bolt.
11. Remove the shock absorber. 1. Remove the bolt and nuts. Discard the nuts.
2. Remove the shock absorber.
12. Position the shock absorber in a vise. 13. Remove the nut and the front shock absorber mounting bracket (18183). Klj . 2 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Spring
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number or an equivalent part must be installed, if installation is necessary. Do
not use a part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to ensure proper retention of these parts.
1. Mark the front shock absorber (18124) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
3. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
4. Remove the cotter pin and nut. Discard the cotter pin.
SECTION 204-
01: Front Suspension 2003 Mustang Workshop Manual Special Tool(s)
Tie-
Rod End Remover
211- 001 (TOOL- 3290-D) or
Equivalent Coil Spring Compressor
204-
D001 (D78P-5310- A) or
Equivalent Klj . 1 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

5.
CAUTION: Use care not to damage the tie- rod end dust boot.
Using the special tool, disconnect the tie- rod from the spindle.
6. Disconnect the front stabilizer bar link (5K483) from the front suspension lower arm (3078). 1. Remove the nut and bushing.
2. Disconnect the link.
7. CAUTION: Do not allow the intermediate shaft to rotate while it is disconnected
from the gear or damage to the clockspring can occur. If there is evidence that the
intermediate shaft has rotated, the clockspring must be removed and recentered. For
additional information, refer to Section 501 - 20B .
Remove the bolt and disconnect the intermediate shaft from the gear. zDiscard the bolt. Klj . 2 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

8.
CAUTION: Correctly support the power rack and pinion steering gear to avoid
damaging the gear and hoses.
Position the power rack and steering gear out of the way. 1. Remove the nuts and bolts.
2. Position the steering gear so the front suspension lower arm front bolt can be removed.
9. Support the front suspension lower arm with a jack stand inboard of the spring seat.
10. NOTE: Note position of the front coil spring (5310) in the lower arm spring seat. It must be
installed in the same position.
Using the special tool, compress the spring until it is loose in the spring insulator (5415). 11. Remove the front suspension lower arm pivot nuts and bolts. Klj . 3 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...