start stop button GENESIS G90 2023 Workshop Manual

5-97
05
WARNING
Automotive fuel is highly flammable
DQGH[SORVLYH)DLOXUHWRIROORZWKHVH
guidelines may result in SERIOUS
INJURY or DEATH:

[Read and follow all warnings posted
at the gas station.

[Before refueling, note the location
RIWKH(PHUJHQF\)XHO6KXW2IILI
available, at the gas station.

[Before touching the fuel nozzle, you
should eliminate the potential build-
up of static electricity by touching
a metal part of the vehicle, a safe
distance away from the fuel filler
neck, nozzle, or other gas source,
with your bare hand.

[Do not use mobile phones while
refueling. Electric current and/or
electronic interference from cellular
phones can potentially ignite fuel
vapors and cause a fire.

[Do not get back into a vehicle
once you have begun refueling.
You can generate a buildup of
static electricity by touching,
rubbing or sliding against any item
or fabric capable of producing
static electricity. Static electricity
discharge can ignite fuel vapors
causing a fire. If you must re-enter
the vehicle, you should once again
eliminate potentially dangerous
static electricity discharge by
touching a metal part of the vehicle,
away from the fuel filler neck, nozzle
or other fuel source, with your bare
hand.
[When using an approved portable
fuel container, be sure to place the
container on the ground prior to
refueling. Static electricity discharge
from the container can ignite fuel
vapors causing a fire.
Once refueling has begun, contact
between your bare hand and the
vehicle should be maintained until
the filling is complete.

[Use only approved portable plastic
fuel containers designed to carry and
store fuel.

[When refueling, always shift the
gear to the P (Park) position, set
the parking brake, and press the
Engine Start/Stop button to the
2))SRVLWLRQ6SDUNVSURGXFHGE\
electrical components related to the
engine can ignite fuel vapors causing
a fire.

[Do not use matches or a lighter and
do not smoke or leave a lit cigarette
in your vehicle while at a gas station,
especially during refueling.

[Do not over-fill or top-off your
vehicle tank, which can cause fuel
spillage.

[If a fire breaks out during refueling,
leave the vicinity of the vehicle, and
immediately contact the manager
of the gas station and then contact
WKHORFDOILUHGHSDUWPHQW)ROORZDQ\
safety instructions they provide.

[If pressurized fuel sprays out, it can
cover your clothes or skin and thus
subject you to the risk of fire and
burns. Always remove the fuel cap
carefully and slowly. If the cap is
venting fuel or if you hear a hissing
sound, wait until the condition stops
before completely removing the cap.

[Always check that the fuel cap is
installed securely to prevent fuel
spillage in the event of an accident.

5-102
Convenience Features
Updating Software
ORS052314N
You can see the progress of the update
on the screen.
After the update is complete, you will
receive a notification on your phone
or the vehicle screen that the software
update is complete.
Information
The screen turns off automatically after 3
minutes to save the battery. If the screen
turns off automatically, you can check the
update progress by pressing the Engine
Start/Stop button.
Information

[After the update starts, you can exit the
vehicle.

[7KH2YHU7KH$LUVRIWZDUHXSGDWH
feature is only available for Active and
(QUROOHG*HQHVLV&RQQHFWHG6HUYLFHV
users.

[The update details may vary, for details
you can visit the What’s New link.

[&KHFNWKHQRWLFHIRUWKH2YHU7KH$LU
software update on mygenesis.com

[,IWKHXSGDWHIDLOVWKH(&8ZLOO
attempt to recovery itself automatically
(rollback). If you want to retry the
software update, even after a successful
UHFRYHU\FRQWDFW*HQHVLV&XVWRPHU
&DUH

[If the update or recovery fails, contact
*HQHVLV&XVWRPHU&DUH

[After the update is complete, it
may provide new functions or
improvements. For more information,
VHHWKH

5-105
05
Parking lamp (()
ORS051269
The parking lamp, license plate lamp and
instrument panel lamp are turned ON.
Headlight (()
ORS051270
The headlight, parking lamp, license
plate lamp and instrument panel lamp
are turned ON.
Information
The Engine Start/Stop button must be in
WKH21SRVLWLRQWRWXUQRQWKHKHDGOLJKW
High Beam Operation
ORS051271L
To turn on the high beam headlight, push
the lever away from you. The lever will
return to its original position.
The high beam indicator will light when
the headlight high beams are switched
on.
To turn off the high beam headlight, pull
the lever towards you. The low beams
will turn on.
ORS051273L
To flash the high beam headlight, pull the
lever towards you, then release the lever.
The high beams will remain ON as long
as you hold the lever towards you.

5-107
05
+HDGOLJKW'HOD\)XQFWLRQ
If the Engine Start/Stop button is in the
ACC position or the OFF position with
the headlights ON, the headlights (and/
or parking lamps) remain on for about
5 minutes. However, if the driver’s door
is opened and closed, the headlights
are turned off after 15 seconds. Also,
with the vehicle off if the driver’s door is
opened and closed, the headlights (and/
or parking lamps) are turned off after 15
seconds.
The headlights (and/or parking lamps)
can be turned off by pressing the lock
button on the smart key twice or turning
the headlight switch to the OFF or AUTO
position.
You can enable the headlight delay
IXQFWLRQE\VHOHFWLQJ
S6HWXS

5-109
05

[Front door lamp ():
The front or rear room lamps come
on when the front or rear doors are
opened. When doors are unlocked
by the smart key, the front and rear
lamps come on for approximately
30 seconds as long as any door
is not opened. The front and rear
room lamps go out gradually after
approximately 30 seconds when the
door is closed. However, if the Engine
Start/Stop button is in the ON position
or all doors are locked, the front and
rear lamps will turn off. If a door is
opened with the Engine Start/Stop
button in the ACC position or the OFF
position, the front and rear lamps will
stay on for about 5 minutes.

[Front room lamp (
)
Press the button to turn on the room
lamp for the front and rear seats.
Press the button again to turn off all
the lamps.
Information
7RDGMXVWWKHOLJKWVXVLQJWKHUHDUDUPUHVW
touchscreen, press from the left side
menu on the touchscreen.
Rear Lamps
ORS051079
ORS051251L
A : Rear seat (if equipped)
B : Rear seat armrest touchscreen (if equipped)

[ : Touch the icon to turn
either lamp on or off.

[
: Touch the icon to turn the lamp
on or off.
Information
7RDGMXVWWKHOLJKWVXVLQJWKHUHDUDUPUHVW
touchscreen, press from the left side
menu on the touchscreen.

5-113
05
Puddle Lamp
ORS051084L
Welcome light
When all doors (and trunk) are closed
and locked, the puddle lamp will turn
on for 15 seconds if any of the below is
performed.

[The doors are unlocked by the smart
key.

[The outside door handle touch sensor
is touched with the smart key in
possession.

[The vehicle is approached with the
smart key in possession. (if equipped)
The puddle lamp turns off if the Engine
Start/Stop button is in the ACC position
with a door open.
For more details, refer to “Welcome
System” in this chapter.
Escort light
When the Engine Start/Stop button is in
the OFF position and the driver’s door is
opened, the puddle lamp will turn on for
30 seconds. If the driver’s door is closed
within the 30 second period, the puddle
lamp will turn off after 15 seconds. If the
driver’s door is closed and locked, the
puddle lamp will turn off immediately.
The Puddle Lamp Escort Light will turn
on only the first time the driver’s door is
opened after the engine is turned off.
Welcome System
ORS051077L
Welcome system helps keep the driver
visible by turning on vehicle lights when
the driver approaches the vehicle.

5-115
05
ORS051272
High Beam Assist will automatically
switch between high beam and low
beam depending on the detected
brightness from the lamps of oncoming
vehicles or vehicles in front.
Detecting sensor
ORS071001L
M: Front view camera
The front view camera is used as a
detecting sensor to detect ambient light
and brightness while driving.
Refer to the picture above for the
detailed location of the detecting sensor.
NOTICE
Always keep the front view camera in
good condition to maintain optimal
performance of High Beam Assist.
)RUPRUHGHWDLOVRQWKHSUHFDXWLRQV
of the front view camera, refer to

U)RUZDUG&ROOLVLRQ$YRLGDQFH$VVLVW
)&$
VVHFWLRQLQFKDSWHU
High Beam Assist Setting
ORS051241L
With the Engine Start/Stop button in the
21SRVLWLRQVHOHFW
S/LJKWV

5-118
Convenience Features
ORS051284
)URQW:LQGVKLHOG:LSHUV
Operates as follows when the Engine
Start/Stop button is in the ON position.
MIST: For a single wiping cycle,
push the lever upward and
release. The wipers will operate
continuously if the lever is held in
this position.
OFF: Wiper is not in operation.
AUTO: The rain sensor located on the
upper end of the windshield
glass senses the amount of
rainfall and controls the wiping
cycle for the proper interval.
The more it rains, the faster the
wiper operates. When the rain
stops, the wiper stops. To vary
the speed setting, turn the speed
control knob.
LO: The wiper runs at a lower speed.
HI: The wiper runs at a higher speed.
Information
If there is heavy accumulation of snow
or ice on the windshield, defrost the
windshield for about 10 minutes, or until
the snow and/or ice is removed before
using the windshield wipers to ensure
proper operation.
If you do not remove the snow and/or ice
before using the wiper and washer, it may
damage the wiper and washer system.
AUTO (Automatic) control
ORS051085
The rain sensor located on the upper
end of the windshield glass senses
the amount of rainfall and controls the
wiping cycle for the proper interval.
The wiper operation time will be
automatically controlled depends on
rainfall.
When the rain stops, the wiper stops.
To vary the sensitivity setting, turn the
sensitivity control knob.
If the wiper switch is set in AUTO mode
when the Engine Start/Stop button is in
the ON position, the wiper will operate
once to perform a self-check of the
system. Set the wiper to the OFF position
when the wiper is not in use.
WIPERS AND WASHERS

5-143
05
To Defrost Inside Windshield
ORS051130
1. Set the fan speed to the highest
(extreme right) position.
2. Set the temperature to the extreme
hot (HI) position.
3. Press the defroster button (
).
4. Fresh mode will be selected
automatically.
Check to make sure the air intake control
is in Fresh mode. If the air intake control
indicator light is illuminated, press the
button once to enable Fresh mode
(indicator light OFF).
If the
position is selected, lower fan
speed is adjusted to a higher fan speed.
Defogging Logic
To reduce the probability of fogging
up the inside of the windshield, the air
intake or air conditioning are controlled
automatically according to certain
conditions. To cancel or reset the
defogging logic, do the following.
1. Press the Engine Start/Stop button to
the ON position.
2. Press the defroster button (
) or
().
3. While pressing the air conditioning
button (A/C), press the air intake
control button at least 5 times within
3 seconds.
The air intake control button indicator
will blink 3 times to indicate that the
defogging logic has been disabled.
Repeat the steps again to re-enable the
defogging logic.
If the battery has been discharged or
disconnected, it resets to the defog logic
status.

5-146
Convenience Features
Turning the Auto Defogging System
ON or OFF
&OLPDWHFRQWUROV\VWHP
Press the front windshield defroster
button for 3 seconds when the Engine
Start/Stop button is in the ON to turn the
system on or off.
To check whether the system is on
or off, go to the settings menu in the
infotainment system and see if 'Auto
Defog' is selected or not.
Infotainment system
Auto Defogging System can be turned
RQDQGRIIE\VHOHFWLQJ
S6HWXS