turn signal HONDA S2000 2007 2.G Owners Manual

Your Vehicle at a Glance
4
HOOD RELEASE HANDLE
HORNWINDSHIELD
WIPERS/
WASHERS
INSTRUMENT
PANEL BRIGHTNESS
(P.57)
(P.56)
(P.58)
VEHICLE
STABILITY ASSIST
(VSA) SYSTEM OFF SWITCH
CRUISE BUTTON
HEADLIGHTS/TURN
SIGNALS
REMOTE AUDIO
CONTROLS
CRUISE CONTROL
BUTTONS
HEATING/COOLING
CONTROLS
ENGINE START BUTTON
(P.104)
(P.124)
(P.112) (P.106) (P.106)
(P.84)
(P.131)
CLOCK
BUTTON
(P.54)

This section gives inf ormation about
the controls and displays that
contribute to the daily operation of
your vehicle. All the essential
controls are within easy reach............................
Control Locations .44
............................
Instrument Panel .45
..........
Instrument Panel Indicators . 46
.............................................
Gauges .51
.....................................
Odometer .51
....................................
Trip meter .51
...............................
Select Button .51
..................................
Fuel Gauge .52
..........
Check Fuel Cap Message . 52
...................
Temperature Gauge . 53
Outside Temperature ...................................
Indicator .53
..................
Maintenance Minder . 54
............................................
Clock .54
Controls Near the Steering ...........................................
Wheel .55
Windshield Wipers and .......................................
Washers .56
...........
Turn Signal and Headlights . 57
........
Instrument Panel Brightness . 58
.................
Hazard Warning Button . 58
.................
Rear Window Def ogger . 59
...............................
Keys and Locks .60
........................
Immobilizer System .61
................................
Ignition Switch .62
..........................
Power Door Locks .63 ................................................
Trunk .63
........
Emergency Trunk Opener . 64
.......................
Remote Transmitter .65
.................................................
Seats .67
..............................
Power Windows .68
..............................
Convertible Top .70
.............................................
Mirrors .75
.................................
Parking Brake .76
...........
Interior Convenience Items . 77
.........................
Beverage Holder .78
...........
Accessory Power Socket . 78
.............
Console Compartments . 79
.................................
Audio Panel .79
..........
Dashboard Lower Pocket . 80
...................................
Interior Light .80
Instruments and Controls
Inst rument s and Cont rols
43

Î
Î
The U.S. instrument panel is shown. Differences for Canadian models are noted in the text.
Instrument Panel
Instru me ntsand Cont ro ls
45
TRUNK-OPEN INDICATOR
IMMOBILIZER SYSTEM INDICATOR
SEAT
BELT
REMINDER
INDICATOR ANTI-LOCK BRAKE
SYSTEM (ABS)
INDICATOR
ELECTRIC POWER
STEERING (EPS)
INDICATOR DOOR-OPEN
INDICATOR
LOW
FUEL
INDICATOR
TURN
SIGNAL AND HAZARD WARNING INDICATORS
HIGH BEAM
INDICATOR
VEHICLE
STABILITY
ASSIST (VSA) SYSTEM
INDICATOR (P.50)
(P.50)
(P.47)
(P.46) PARKING BRAKE AND
BRAKE SYSTEM INDICATOR
CHARGING SYSTEM INDICATOR
LOW
OIL PRESSURE INDICATORMALFUNCTION
INDICATOR LAMP
CRUISE
CONTROL INDICATOR (P.47)
(P.47) MAINTENANCE
MINDER
INDICATOR
(P.47)(P.49) (P.47)
(P.48)
(P.50)
(P.48) (P.49)
DAYTIME
RUNNING
LIGHTS INDICATOR
SUPPLEMENTAL RESTRAINT SYSTEM
INDICATOR
VSA
ACTIVATION INDICATOR
(P.48) (P.46, 188)
(P.46, 186)
(P.46,
186) (P.47,
187)
(P.49)
(P.51,
135)
INFORMATION
DISPLAY
OUTSIDE
TEMPERATURE INDICATOR (P.53)

If this indicator comes on when the
ignition switch is turned to the ON
(II) position and the parking brake is
rele ased, it means there is a problem
in the high beam headlight’s circuit.
Have your vehicle checked by your
dealer.
Driving
with the power steering
system continuously overheating can
cause system damage.
The left or right turn signal indicator
blinks when you signal a lane change
or turn. If the indicator does not
blink or blinks rapidly, it usually
means one of the turn signal bulbs is
burned out (see page ). Replace
the bulb as soon as possible, since
other drivers cannot see that you are
signaling.
When you press the hazard warning
button, both turn signal indicators
blink. All turn signals on the outside
of the vehicle should f lash.
This indicator normally comes on
when you turn the ignition to the ON
(II) position and goes of f af ter the
engine starts. If it comes on at any
other time, there is a problem in the
electric power steering system. If
this happens, stop the vehicle in a
saf e place and turn of f the engine.
Reset the system by restarting the
engine. The indicator will not turn
of f immediately. If it does not go of f
after driving a short distance, or
comes on again while driving, take
the vehicle to your dealer to have it
checked. With the indicator on, the
EPS may be turned of f , making the
vehicle harder to steer.
If the power steering system
overheats while driving, the assist is
reduced and steering may f eel
slightly harder.
157
Instrument Panel Indicators
‘‘Daytime Running
Lights’’ Indicator
Turn Signal and
Hazard Warning
Indicators
Electric Power Steering
(EPS) Indicator
48

Î
ÎTo use the horn, press the pad around the ‘‘H’’ logo.
Controls Near the Steering Wheel
Instru me ntsand Cont ro ls
55
REMOTE AUDIO
CONTROLS
HOOD RELEASE
HANDLE INSTRUMENT
PANEL BRIGHTNESS
HEADLIGHTS/TURN
SIGNALS
ENGINE START BUTTON
HORNWINDSHIELD
WIPERS/WASHERS
(P.57)
(P.56)
(P.58)
VEHICLE STABILITY ASSIST (VSA)
SYSTEM OFF SWITCH
CRUISE BUTTON (P.54) CLOCK BUTTON
CRUISE CONTROL BUTTONSHEATING/COOLING
CONTROLS
(P.104)
(P.124)
(P.112) (P.106) (P.106)(P.84)
(P.131)

µµ µ
Push down on the
lever to signal a left turn and up to
signal a right turn. To signal a lane
ch ange, push lightly on the lever,
and hold it. The lever will return to
center when you release it or
complete a turn.
Turning the
switch to the ‘‘ ’’ position turns
on the parking lights, taillights,
instrument panel lights, side-marker
lights, and rear license plate lights.
Turning the switch to the ‘‘ ’’
position turns on the headlights. If
you leave the lights on with the key
removed from the ignition switch,
you will hear a reminder buzzer
when you open the driver’s door.
Turn
Signal
Off
Parking and indicator lights
Headlights on
High beams
Flashhighbeams Push the lever
f orward until you hear a click. The
high beam indicator will come on
(see page ). Pull the lever back to
return to the low beams.
To f lash the high beams, pull the
lever back lightly, then release it.
The high beams will stay on as long
as you hold the lever back.
With the headlight switch off, the
high beam headlights and the high
beam indicator come on with
reduced brightness when you turn
the ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.
1.
2.
3.
4.
5.
6. 49
Turn Signal
Headlights On High Beams
Daytime Running L ights
Turn Signal and Headlights
Inst rument s and Cont rols
57

´µ´µ
The buttons in the lower left corner
of the instrument panel adjust the
brightness of the display in f ive steps.
Push the or button five times
to see the f ull range. To reduce glare at night, the
instrument panel illumination dims
when you turn the light switch to the
or position.
Push the red button next to the
parking brake to turn on the hazard
warning lights (f our-way f lashers).
This causes all f our outside turn
signals and both indicators in the
instrument panel to f lash. Use the
hazard warning lights if you need to
park in a dangerous area near heavy
traffic, or if your vehicle is disabled.
Adjust the brightness to the desired
level with the headlight switch of f ,
and also with the headlight switch on.
Both settings will remain at those
levels until you change them.
With the headlight switch on, you
can switch the display to f ull daytime
brightness by pushing and holding
the button. Push the button to
return the display to the original
brightness.
Instrument Panel Brightness
Hazard Warning Button
Instrument Panel Brightness, Hazard Warning Button
58

µµ
µ µ
µ
µ
You can use any of f ive methods to
find radio stations on the selected
band: tune, seek, scan, the preset
buttons, and auto select. Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a lower f requency.
The seek f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press the or side of the
bar, then release it.
If you do nothing, the system will
scan f or the next strong station and
play it f or 5 seconds. When it plays a
station you want to listen to, press
the SCAN button again. The scan f unction samples
all stations with strong signals on the
selected band. To activate it, press
the SCAN button, then release it.
You will see SCAN in the display.
The system will scan f or a station
with a strong signal. When it f inds
one, it will stop and play that station
f or about 5 seconds.
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position. Turn the system on by
pushingthePWR/VOLknoborthe
AM/FM button. Adjust the volume
by turning the same knob.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
button. On the FM band, ST will be
displayed if the station is broadcast-
ing in stereo. Stereo reproduction in
AM is not available.
Each preset button
(1 6) can store one station on AM,
and two stations on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
twelve stations.
Usethetune,seek,orscan
function to tune the radio to a
desired station.
Pick a preset number (1 6), and
hold it until you hear a beep.
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
The preset f requencies may be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. 1.
2.
3.
4.
CONT INUED
To Play the Radio
To Select a Station
TUNE SEEK
SCAN
PRESET
Playing the AM/FM Radio
Features
89

Depending on where you drive, you
may experience reception problems.
Interf erence can be caused by any of
these conditions:Driving on a road beside a vertical
wall, steep clif f , or hill to the south
of you. Driving on the north side of a
large commercial truck on an
east/west road.
Driving in tunnels.
Driving on a single lane road
alongside dense trees taller than
50 ft. (15 m) to the south of you. Driving on the south side of an
east/west mountain road. There may also be other geographic
situations that could af f ect satellite
radio reception.
If you decide to purchase XM
satellite radio service, contact XM
Radio at
, or at1-800-852-9696. You will need to give
them your radio I.D. number and
your credit card number. To get your
radio I.D. number, turn the TUNE
knob until ‘‘0’’ appears in the display.
Your I.D. will appear in the display.
After you’ve registered with XM
Radio, keep your audio system in the
Satellite Radio mode while you wait
f or activation. This should take about
30 minutes.
While waiting for activation, make
sure your vehicle remains in an open
area with good reception. Once your
audio system is activated, ‘‘category’’
or ‘‘CH’’ will appear in the display,
andyou’llbeabletolistentoXM
Radio broadcasts. XM Radio will
continue to send an activation signal
to your vehicle for at least 12 hours
from the activation request. If the
service has not been activated after
36 hours, contact XM Radio.
Driving on the lower level of a
multi-tiered road. If your XM Radio service has expired,
or you purchased your vehicle f rom
a previous owner, you can listen to a
sampling of the broadcasts available
on XM Satellite Radio. With the
ignition switch in the ACCESSORY
(I) or the ON (II) position, push the
PWR/VOL knob to turn on the audio
system, and press the CD/XM
button. A variety of music types and
styles will play.
As required by the FCC:
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
www.xmradio.com
Playing the XMSatellite Radio (Optional on U.S. Models)
Receiving Satellite Radio Service
Features
97

If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, then turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.Use a f lat-tipped screwdriver to
remove the three holding clips
f rom the inner f ender.
Pull the inner f ender cover back.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Install the new bulb in the socket.
Put the inner f ender cover in place.
Install the three holding clips.
Lock each clip in place by pushing
on the center. Turn on the lights to make sure
the new bulb is working.
1.
2.
3.
4.
5.6.
7.
8.
9.
Replacing Front Turn Signal and
Side Marker/Parking L ight Bulbs
Lights
Maint enance
157