ignition Hyundai Elantra 2016 Quick Reference Guide

Page 3 of 20

03 02
ELANTRA
GET TING STARTED
REMOTE KEYLESS ENTRY
Driver’s door lock/unlockSmart key must be within range.Press:Once – Unlock driver door
Twice – Unlock all doors
Third – Lock all doorsRemove mechanical keyPress and hold the release
A button and remove
the key.
Reinstall mechanical keyPut the key into the hole and push it until a click
sound is heard.
A
With the ignition
OFF, press
the engine start / stop button:
 t0ODFGPS"$$ "DDFTTPSZ
NPEF
 t5XJDFGPS0/NPEF
 t5ISFFUJNFTGPS0''To start the engine, press the
start/stop button while: t"VUPNBUJD5SBOTNJTTJPOEFQSFTTJOHUIFCSBLFQFEBM
 t.BOVBM5SBOTNJTTJPOEFQSFTTJOHUIFDMVUDIBOECSBLFQFEBMTTo shut engine OFF, shift to: t"VUPNBUJD5SBOTNJTTJPO1 1BSL
BOEQSFTTUIFTUBSUTUPQCVUUPO
t.BOVBM5SBOTNJTTJPO4FMFDUTUHFBSPS/FVUSBM
BQQMZUIF
QBSLJOHCSBLF
BOEQSFTTUIFTUBSUTUPQCVUUPOEmergency situations tShut off engine while driving:
1SFTTFOHJOFTUBSUTUPQCVUUPOGPSNPSFUIBOTFDPOETPS
press it 3 times consecutively within 3 seconds.
t
Restart engine while driving:
1SFTTFOHJOFTUBSUTUPQCVUUPOXJUITIJGUMFWFSJO/ /FVUSBM
ENGINE START / STOP BUTTON
HYUNDAI LockUnlockTrunk unlockPanic
Remote Key Smart KeyDownload QR Code ReaderYou can download a QR reader app to your smart phone to take advantage
of the QR codes throughout this Quick Reference Guide.
iPhone
® - Apple
® App Store
Android
® - Google Play
BlackBerry® - BlackBerry
® App World

Page 19 of 20

35 34
ELANTRA HYUNDAI
REARVIEW CAMERA
The rearview camera will activate
when the ignition switch is turned
ON and the shift lever is in the R
(Reverse) position.
Rearview display
CHILD-PROTECTOR REAR DOOR LOCK
Lock (
)
Only allows opening the
rear door handle from
outside of the vehicle. Insert a key into the hole and
turn it to the following positions:Unlock (
)
Allows opening the rear
door handle from inside
and outside the vehicle.
00 10123
4
5
6 20304050
60
70
80
or
ENGINE
START
STOP
321
0
TIRE MOBILITY KIT
0 10 20304050min 2.2 bar/ 32 psi
60
70
80
90
FEATURES AND CONTROLS
Setup1. Remove the speed restriction label
from the sealant bottle and place it on
the center of the steering wheel.
2. Ensure that the compressor is
switched to OFF.
3. Lift the cable cover
and screw the
compressor hose on to the
connector of the sealant bottle.
4. Insert the sealant bottle into the
housing slot
of the compressor.
5. Screw the filling hose
of the sealant
bottle onto the tire’s valve stem.
6. Insert the compressor power plug

into the vehicle’s power outlet.
7. Turn the ignition switch to the ON
position or press the Engine Start/Stop
button twice.
Inflate Tire1. Switch ON the compressor and let it
run for approximately 5 minutes.
2. Switch OFF the compressor and check
to ensure that inflation pressure is over
32 psi. If not, the puncture is too large
to repair. Contact Hyundai Roadside
Assistance.
3. Remove the filling hose
,
compressor hose
,
and compressor power plug
.
continued on next page... lll