rear view mirror HYUNDAI GENESIS GV70 2022 User Guide
Page 261 of 647
05
5-127
Sunvisor
OHI048444OHI048444
To use the sunvisor, pull it downward.
To use the sunvisor to block the sun from
the side window, pull it rearward, release
it from the bracket (1) and swing it to the
side (2) towards the window.
To use the vanity mirror, pull down the
sunvisor and slide the mirror cover (3).
Adjust the sunvisor forward or backward
(4) as needed (if equipped). Use the
ticket holder (5) to hold tickets.
Close the vanity mirror cover securely
and return the sunvisor to its original
position after use.
WARNING
For your safety, do not block your view
when using the sunvisor.
NOTICE
The tab (5) adjacent to the vanity mirror
on the sunvisor can be used for toll
road tickets or self parking tickets. Use
caution when inserting tickets into the
ticket holder to avoid damage. Refrain
from putting several tickets in the ticket
holder as this could also damage the
retaining tab.
Power Outlet
„ „FrontFront
OJK050047OJK050047
„ „Luggage compartmentLuggage compartment
OJK050070OJK050070
The power outlet is designed to provide
power for mobile telephones or other
devices designed to operate with vehicle
electrical systems. The devices should
draw less than 180 watts with the engine
running.
Page 386 of 647
07
7-37
Collision Warning
• Collision warning will operate when
the turn signal is turned on in the
direction of the detected vehicle.
• If ‘Warning Only’ is selected from the
Settings menu, the collision warning
will operate when your vehicle
approaches the lane the blind spot
vehicle is detected.
• To warn the driver of a collision, the
warning light on the side view mirror
and head-up display (if equipped) will
blink. At the same time, an audible
warning will sound and the steering
wheel will vibrate.
• When the turn signal is turned off or
you move away from the lane, the
collision warning will be canceled and
Blind-Spot Collision-Avoidance Assist
will return to vehicle detection state. : $ 5 1 , 1 *
• The detecting range of the rear
F R U Q H U U D G D U L V G H W H U P L Q H G E \ D
V W D Q G D U G U R D G Z L G W K W K H U H I R U H R Q
D Q D U U R Z U R D G % O L Q G 6 S R W & R O O L V L R Q
$ Y R L G D Q F H $ V V L V W P D \ G H W H F W R W K H U
Y H K L F O H V L Q W Z R O D Q H V R Y H U D Q G Z D U Q
\ R X , Q F R Q W U D V W R Q D Z L G H U R D G
% O L Q G 6 S R W & R O O L V L R Q $ Y R L G D Q F H
$ V V L V W P D \ Q R W E H D E O H W R G H W H F W D
Y H K L F O H G U L Y L Q J L Q W K H Q H [ W O D Q H D Q G
P D \ Q R W Z D U Q \ R X
• : K H Q W K H K D ] D U G Z D U Q L Q J I O D V K H U L V
R Q W K H F R O O L V L R Q Z D U Q L Q J E \ W K H W X U Q
V L J Q D O Z L O O Q R W R S H U D W H
Information
If the driver's seat is on the left side, the
collision warning may occur when you
turn left. Maintain a proper distance with
the vehicles in the left lane. If the driver's
seat is on the right side, the collision
warning may occur when you turn right.
Maintain a proper distance with the
vehicles in the right lane.
Page 399 of 647
Driver Assistance System
7-50
OTM070100NOTM070100N
When the side view mirror warning
light is not working properly, the ‘Check
side view mirror warning light’ warning
message will appear on the cluster
for several seconds, and the master
(
) warning light will illuminate on
the cluster. If the master warning light
illuminates, have the vehicle inspected
by an authorized retailer of Genesis
Branded products.
Safe Exit Warning disabled
OTM070098NOTM070098N
When the rear bumper around the rear
corner radar or sensor is covered with
foreign material, such as snow or rain,
or installing a trailer or carrier, it can
reduce the detecting performance and
temporarily limit or disable Safe Exit
Warning.
If this occurs, the ‘Blind-Spot Safety
system disabled. Radar blocked’ warning
message will appear on the cluster.
Safe Exit Warning will operate properly
when such foreign material or trailer,
etc. is removed, and then the engine is
restarted.
If Safe Exit Warning does not operate
properly after it is removed, have the
vehicle inspected by an authorized
retailer of Genesis Branded products.
Page 404 of 647
07
7-55
OTM070145LOTM070145L
Safe Exit Assist linked with Electronic
child safety lock
• When Electric child safety lock is
operating and an approaching vehicle
from the rear area is detected, the rear
doors cannot be unlocked even if the
driver tries to unlock the rear doors
using the electronic child safety lock
button. The warning light on the side
view mirror will blink and the ‘Check
surroundings then try again’ warning
message will appear on the cluster.
• Safe Exit Assist will warn the driver
when vehicle speed is below 2 mph
(3 km/h) and the speed of the
approaching vehicle from the rear is
above 4 mph (6 km/h).
• For more details on electric child
safety lock button, refer to “Electronic
Child Safety Lock” section in chapter
5.
& $ 8 7 , 2 1
, I W K H G U L Y H U S U H V V H V W K H H O H F W U R Q L F F K L O G
O R F N E X W W R Q D J D L Q Z L W K L Q V H F R Q G V
D I W H U W K H Z D U Q L Q J P H V V D J H D S S H D U V
6 D I H ( [ L W $ V V L V W M X G J H V W K D W W K H G U L Y H U
has unlocked the doors acknowledging
W K H U H D U V W D W X V 7 K H H O H F W U R Q L F F K L O G
V D I H W \ O R F N Z L O O W X U Q R I I E X W W R Q
indicator OFF) and the rear doors will
X Q O R F N $ O Z D \ V F K H F N W K H V X U U R X Q G L Q J V
E H I R U H W X U Q L Q J R I I W K H H O H F W U R Q L F F K L O G
V D I H W \ O R F N E X W W R Q
Information
If a rear door is opened from the outside,
it will open regardless of Safe Exit Assist
operation.
: $ 5 1 , 1 *
Take the following precautions when
X V L Q J 6 D I H ( [ L W $ V V L V W
• ) R U \ R X U V D I H W \ F K D Q J H W K H 6 H W W L Q J V
D I W H U S D U N L Q J W K H Y H K L F O H D W D V D I H
O R F D W L R Q
• , I D Q \ R W K H U V \ V W H PT V Z D U Q L Q J
P H V V D J H L V G L V S O D \ H G R U D X G L E O H
Z D U Q L Q J L V J H Q H U D W H G 6 D I H ( [ L W
$ V V L V W Z D U Q L Q J P H V V D J H P D \ Q R W E H
G L V S O D \ H G D Q G D X G L E O H Z D U Q L Q J P D \
Q R W E H J H Q H U D W H G
• < R X P D \ Q R W K H D U W K H Z D U Q L Q J V R X Q G
R I 6 D I H ( [ L W $ V V L V W L I W K H V X U U R X Q G L Q J
L V Q R L V \
• 6 D I H ( [ L W $ V V L V W G R H V Q R W R S H U D W H L Q
D O O V L W X D W L R Q V R U F D Q Q R W S U H Y H Q W D O O
F R O O L V L R Q V
Page 406 of 647
07
7-57
OTM070100NOTM070100N
When the side view mirror warning
light is not working properly, the ‘Check
side view mirror warning light’ warning
message will appear on the cluster
for several seconds, and the master
(
) warning light will illuminate on
the cluster. If the master warning light
illuminates, have the vehicle inspected
by an authorized retailer of Genesis
Branded products.
Safe Exit Assist disabled
OTM070098NOTM070098N
When the rear bumper around the rear
corner radar or sensor is covered with
foreign material, such as snow or rain,
or installing a trailer or carrier, it can
reduce the detecting performance and
temporarily limit or disable Safe Exit
Assist.
If this occurs, the ‘Blind-Spot Safety
system disabled. Radar blocked’ warning
message will appear on the cluster.
Safe Exit Assist will operate properly
when such foreign material or trailer,
etc. is removed, and then the engine is
restarted.
If Safe Exit Assist does not operate
properly after it is removed, have the
vehicle inspected by an authorized
retailer of Genesis Branded products.
Page 426 of 647
07
7-77
„ „Left sideLeft side „ „Right sideRight side
OJK071201NOJK071201NOJK071202NOJK071202N
Blind-Spot View Monitor displays the
rear blind spot area of the vehicle in the
cluster when the turn signal is turned on
to help safely change lanes.
Detecting sensor
OJK071049NOJK071049N[1], [2]: Surround-side view camera
(camera located at bottom of the mirror)
Refer to the picture above for the
detailed location of the detecting
sensors.
% O L Q G 6 S R W 9 L H Z 0 R Q L W R U
Settings
Setting features
Blind-Spot View
With the engine on, select ‘Driver
$ V V L V W D Q F H
Page 473 of 647
Driver Assistance System
7-124
OJK070163LOJK070163L
OJK071236NOJK071236N
Surround View Monitor can assist in
parking by allowing the driver to see
around the vehicle.
Detecting sensor
OJK071056NOJK071056N
OJK070057OJK070057
[1] : Surround-front view camera,
[2],[3] : Surround-side view camera
(under the side view mirror),
[4] : Surround-rear view camera
Refer to the picture above for the
detailed location of the detecting
sensors.
6 8 5 5 2 8 1 ' 9 , ( : 0 2 1 , 7 2 5
Page 482 of 647
07
7-133
• Rear Cross-Traffic Collision-Avoidance
Assist will operate when all the
following conditions are satisfied:
- The gear is shifted to R (Reverse)
- Vehicle speed is below 5 mph (8
km/h)
- The approaching vehicle is within
approximately 82 ft. (25 m) from the
left and right side of your vehicle
- The speed of the vehicle
approaching from the left and right
is above 3 mph (5 km/h)
Information
If the operating conditions are satisfied,
there will be a warning whenever the
vehicle approaches from the left or right
side even though your vehicle speed is 0
mph (0 km/h).
OPDEN060039OPDEN060039OJK070108LOJK070108L
OJK070131OJK070131
Emergency Braking
• To warn the driver of an approaching
vehicle from the rear left/right side
of your vehicle, the warning light on
the side view mirror will blink and a
warning message will appear on the
cluster. At the same time, an audible
warning will sound and the steering
wheel will vibrate. A warning will also
appear on the infotainment system
screen.
Page 485 of 647
Driver Assistance System
7-136
Rear Cross-Traffic Collision-
$ Y R L G D Q F H $ V V L V W 0 D O I X Q F W L R Q
and Limitations
Rear Cross-Traffic Collision-
Avoidance Assist malfunction
OTM070125NOTM070125N
When Rear Cross-Traffic Collision-
Avoidance Assist is not working properly,
the ‘Check Rear Cross-Traffic Safety
system’ warning message will appear on
the cluster for several seconds, and the
master (
) warning light will illuminate
on the cluster. If the master warning light
illuminates, have the vehicle inspected
by an authorized retailer of Genesis
Branded products.
OTM070100NOTM070100N
When the side view mirror warning
light is not working properly, the ‘Check
side view mirror warning light’ warning
message will appear on the cluster
for several seconds, and the master
(
) warning light will illuminate on
the cluster. If the master warning light
illuminates, have the vehicle inspected
by an authorized retailer of Genesis
Branded products.
Rear Cross-Traffic Collision-
Avoidance Assist disabled
OTM070124NOTM070124N
When the rear bumper around the rear-
side radar or sensor is covered with
foreign material, such as snow or rain,
or installing a trailer or carrier, it can
reduce the detecting performance and
temporarily limit or disable Rear Cross-
Traffic Collision-Avoidance Assist.
If this occurs, the ‘Rear Cross-Traffic
Safety system disabled. Radar blocked’
warning message will appear on the
cluster.
Rear Cross-Traffic Collision-Avoidance
Assist will operate properly when
such foreign material or trailer, etc. is
removed.
If Rear Cross-Traffic Collision-Avoidance
Assist does not operate properly after it
is removed, have the vehicle inspected
by an authorized retailer of Genesis
Branded products.
Page 622 of 647
09
9-65
Exterior Care
NOTICE
If you park your vehicle near a stainless
steel sign or glass facade building, the
vehicle’s exterior plastic parts such
as a bumper, spoiler, garnish, lamp
or outside rearview mirror might be
damaged due to sunlight reflected from
the sign or building. To prevent damage
of the exterior plastic parts, you should
avoid parking in areas where light may
be reflected or use a car cover. (The
exterior plastic parts applied to your
vehicle may vary.)
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning and
caution statements that appear on the
label.
Finish maintenance
Washing
To help protect your vehicle’s finish from
rust and deterioration, wash it thoroughly
and frequently at least once a month
with lukewarm or cold water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to the
removal of any accumulation of salt, dirt,
mud, and other foreign materials. Make
sure the drain holes in the lower edges
of the doors and rocker panels are kept
clear and clean.Insects, tar, tree sap, bird droppings,
industrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, should be used.
After washing, rinse the vehicle
thoroughly with lukewarm or cold water.
Do not allow soap to dry on the finish.
High-pressure washing
• When using high-pressure washers,
make sure to maintain sufficient
distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.
• Do not spray the camera, sensors or
its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.
• Do not bring the nozzle tip close to
boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
WARNING
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by water
before getting on the road. If braking
performance is impaired, dry the
brakes by applying them lightly while
maintaining a slow forward speed.
APPEARANCE CARE