display INFINITI FX35 2004 Owner's Manual

TROUBLE DIAGNOSIS FOR SYMPTOMS
ACS-59
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
TROUBLE DIAGNOSIS FOR SYMPTOMSPFP:00007
Symptom ChartAKS006ZN
Symptoms Reference page
OperationON/OFF switch does not switch ON.Symptom 1
ACS-60
ON/OFF switch does not switch OFF.Symptom 1
ACS-60
Cruise does not function for setting (powering functions).Symptom 2
ACS-60
CANCEL switch does not function.Symptom 3
ACS-61
Resume does not function.Symptom 3
ACS-61
The set speed does not increase.Symptom 3
ACS-61
The set distance to the vehicle ahead cannot be changed.Symptom 3
ACS-61
The ICC is not cancelled when the gear is in other than D.Symptom 4
ACS-62
Display/ChimeThe ICC system display does not appear.Check combination meter.
Refer to DI-13, "
How to Pro-
ceed With Trouble Diagnosis"
Chime does not function.Symptom 5
ACS-62
Control Driving force is hunting.Symptom 6
ACS-63
Function to detect the vehicle
aheadThe system frequently cannot detect the vehicle ahead.Symptom 7
ACS-63
The distance to detect the vehicle ahead is short.Symptom 7
ACS-63
The system misidentifies a vehicle even though there is no
vehicle ahead.

Refer to ACS-12, "LASER
BEAM AIMING ADJUST-
MENT"

Refer to ACS-9, "ICC Sys-
tem Running Test"
The system misidentifies a vehicle in the next lane.

Refer to ACS-12, "LASER
BEAM AIMING ADJUST-
MENT"

Refer to ACS-9, "ICC Sys-
tem Running Test"
The system does not detect a vehicle at all.Symptom 8
ACS-63

ACS-60
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2004 November 2004 FX35/FX45
Symptom 1: ON/OFF Switch Does Not Switch ON*1 . ON/OFF Switch Does Not
Switch OFF
*2 .AKS006ZO
NOTE:

*1:The ICC system display in the combination meter does not illuminate.

*2:The ICC system display in the combination meter remains powered.
1. CHECK ON/OFF SWITCH
With CONSULT-II

With data monitor, check that ON/OFF switch operates normally.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK CONNECTOR ICC UNIT
1. Turn ignition switch OFF.
2. Disconnect ICC unit connector.
3. Check connector housing for disconnected, loose, bent, and collapsed terminals.
OK or NG
OK >> GO TO 3.
NG >>

Poor connector connection.

Repair ICC unit connector. After repair, erase DTC and perform ICC system running test. Then
perform self-diagnosis of ICC system again.
3. DIAGNOSIS CHECK
With CONSULT-II

Perform self-diagnosis with CONSULT-II.Is“CAN COMM CIRCUIT”indicated?
YES or NO
YES >> Refer toACS-41, "DTC 20 CAN COMM CIRCUIT"
NO >> Refer toACS-45, "DTC 46 OPERATION SW CIRC"
Symptom 2: The ICC System Cannot Be Set (ON/OFF Switch Turns On/Off).AKS006ZP
The ICC cannot be set in the following cases.

When the vehicle speed is not in range of approx. 25 MPH (40 km/h) to 90 MPH (144 km/h).

When the A/T selector lever is in gears other than ‘D’.

While the brake is in operation.
1. CHECK OF CAUSE OF AUTOMATIC CANCELLATION
With CONSULT-II
1. With “CAUSE OF AUTO-CANCEL” in work support, check if any cause of cancellation exists.
OK or NG
OK >>
Cancel with appropriate cause.

For causes A, B, or C, go to specified diagnosis.
A:“OPE SW VOLT CIRC” : Refer to ACS-45, "
DTC 46 OPERATION SW CIRC" .
B:“ VHCL SPD UNMATCH” : Refer to ACS-42, "
DTC 41 VHCL SPEED SE CIRC" .
C:“IGN LOW VOLT” : Refer to ACS-42, "
DTC 31 POWER SUPPLY CIR, DTC 34
POWER SUPPLY CIR 2" .
NG >> GO TO 2.

TROUBLE DIAGNOSIS FOR SYMPTOMS
ACS-63
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
2. CAN COMMUNICATION INSPECTION
With CONSULT-II
1. With CONSULT-II self-diagnosis, check that “CAN COMM CIRCUIT” item exists.
OK or NG
OK >> Refer to ACS-41, "DTC 20 CAN COMM CIRCUIT" .
NG >> After replacing combination meter, erase DTC. Perform ICC system running test, and then per-
form self-diagnosis of ICC system again.
Symptom 6: Driving Force Is Hunting.AKS006ZU
1. CHECK ECM
1. Perform self-diagnosis of ECM.
OK or NG
OK >> Refer toACS-63, "Symptom 7: The ICC System Frequently Cannot Detect the Vehicle Ahead/The
Detection Zone Is Short." .
NG >> After repairing applicable parts, erase DTC. Perform ICC system running test, and then perform
self-diagnosis of ICC system again.
Symptom 7: The ICC System Frequently Cannot Detect the Vehicle Ahead/The
Detection Zone Is Short.
AKS006ZV
The detection function may become unstable in the following cases:

When the reflector of the vehicle ahead is deficient/ not clean enough to reflect the radar.

When driving a road with extremely sharp corners.

When the radar cannot detect the reflector of the vehicle ahead as the vehicle ahead is passing a hill or
passing the peak.
1. VISUAL CHECK
1. Check ICC sensor body window for contamination and foreign materials.
OK or NG
OK >> If any contamination or foreign materials are found, remove them. Then perform ICC system run-
ning test.
NG >> GO TO 2.
2. CHECK FUNCTION
1. After adjusting ICC sensor beam aiming, perform ICC system running test. Check that preceding vehicle
detection performance has been improved.
OK or NG
OK >> INSPECTION END
NG >>

Replace ICC sensor, and perform laser beam aiming adjustment.

After performing above. Perform ICC system running test, and then perform self-diagnosis of
ICC system again.
Symptom 8: The System Does Not Detect the Vehicle Ahead at All.AKS006ZW
1. VISUAL CHECK
1. With ignition switch turned ON (engine not started), check that all indicator lamps in ICC system display
are continuously lit. (Check for a missing segment in preceding vehicle detection display.)
OK or NG
OK >> GO TO 2.
NG >> Check for combination meter. Refer to DI-13, "
How to Proceed With Trouble Diagnosis" in DI.

INDEX FOR DTC
AT-5
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
INDEX FOR DTCPFP:00024
Alphabetical Index ACS0079V
NOTE:
If DTC “U1000” is displayed with other DTC, first perform the trouble diagnosis for “DTC U1000 CAN
COMMUNICATION LINE”. Refer to AT- 1 0 5
.
*1: These numbers are prescribed by SAE J2012.
*2: For VQ35DE engine.
*3: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.Items
(CONSULT-II screen terms) DTC
Reference page OBD-II Except OBD-II
CONSULT-II (GST*1) CONSULT-II only “A/T”
A/T 1ST E/BRAKING — P1731AT- 1 5 0
ATF PRES SW 1/CIRC — P1841AT- 1 7 8
ATF PRES SW 3/CIRC — P1843AT- 1 8 0
ATF PRES SW 5/CIRC — P1845AT- 1 8 2
ATF PRES SW 6/CIRC — P1846AT- 1 8 4
A/T INTERLOCK P1730 P1730AT- 1 4 7
A/T TCC S/V FNCTN P0744 P0744 AT- 1 2 5
ATF TEMP SEN/CIRC P0710 P1710AT- 1 3 9
CAN COMM CIRCUIT U1000 U1000AT- 1 0 5
D/C SOLENOID/CIRC P1762 P1762AT- 1 6 0
D/C SOLENOID FNCTN P1764 (*3) P1764 AT- 1 6 2
ENGINE SPEED SIG P0725 (*2) P0725AT- 1 2 1
FR/B SOLENOID/CIRC P1757 P1757AT- 1 5 6
FR/B SOLENOID FNCT P1759 P1759 AT- 1 5 8
HLR/C SOL/CIRC P1767 P1767AT- 1 6 4
HLR/C SOL FNCTN P1769 (*3) P1769 AT- 1 6 6
I/C SOLENOID/CIRC P1752 P1752AT- 1 5 2
I/C SOLENOID FNCTN P1754 (*3) P1754 AT- 1 5 4
L/PRESS SOL/CIRC P0745 P0745AT- 1 2 7
LC/B SOLENOID/CIRC P1772 P1772AT- 1 6 8
LC/B SOLENOID FNCT P1774 P1774 AT- 1 7 0
MANU MODE SW/CIR — P1815AT- 1 7 2
PNP SW/CIRC P0705 P0705AT- 11 2
STARTER RELAY/CIRC — P0615AT- 1 0 8
TCC SOLENOID/CIRC P0740 P0740AT- 1 2 3
TCM·EEPROM — P1704AT- 1 3 5
TCM-POWER SUPPLY — P1701AT- 1 2 9
TCM·RAM — P1702AT- 1 3 3
TCM·ROM — P1703AT- 1 3 4
TP SEN/CIRC A/T P1705 (*2) P1705AT- 1 3 6
TURBINE REV S/CIRC P1716 P1716AT- 1 4 3
VEH SPD SE/CIR·MTR — P1721AT- 1 4 5
VEH SPD SEN/CIR AT P0720 P0720AT- 11 6

AT-6
INDEX FOR DTC
Revision: 2004 November 2004 FX35/FX45
DTC No. Index ACS0079W
NOTE:
If DTC “U1000” is displayed with other DTC, first perform the trouble diagnosis for “DTC U1000 CAN
COMMUNICATION LINE”. Refer to AT- 1 0 5
.
*1: These numbers are prescribed by SAE J2012.
*2: For VQ35DE engine.
*3: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.DTC
Items
(CONSULT-II screen terms)Reference page OBD-II Except OBD-II
CONSULT-II GST (*1) CONSULT-II only “A/T”
— P0615 STARTER RELAY/CIRCAT-108
P0705 P0705 PNP SW/CIRCAT- 11 2
P0710 P1710 ATF TEMP SEN/CIRCAT-139
P0720 P0720 VEH SPD SEN/CIR ATAT- 11 6
P0725 (*2) P0725 ENGINE SPEED SIGAT-121
P0740 P0740 TCC SOLENOID/CIRCAT-123
P0744 P0744 A/T TCC S/V FNCTNAT-125
P0745 P0745 L/PRESS SOL/CIRCAT-127
— P1701 TCM-POWER SUPPLYAT-129
— P1702 TCM·RAMAT-133
— P1703 TCM·ROMAT-134
— P1704 TCM·EEPROMAT-135
P1705 (*2) P1705 TP SEN/CIRC A/TAT-136
P1716 P1716 TURBINE REV S/CIRCAT-143
— P1721 VEH SPD SE/CIR·MTRAT-145
P1730 P1730 A/T INTERLOCKAT-147
— P1731 A/T 1ST E/BRAKINGAT-150
P1752 P1752 I/C SOLENOID/CIRCAT-152
P1754 (*3) P1754 I/C SOLENOID FNCTNAT-154
P1757 P1757 FR/B SOLENOID/CIRCAT-156
P1759 (*3) P1759 FR/B SOLENOID FNCTAT-158
P1762 P1762 D/C SOLENOID/CIRCAT-160
P1764 (*3) P1764 D/C SOLENOID FNCTNAT-162
P1767 P1767 HLR/C SOL/CIRCAT-164
P1769 P1769 HLR/C SOL FNCTNAT-166
P1772 P1772 LC/B SOLENOID/CIRCAT-168
P1774 P1774 LC/B SOLENOID FNCTAT-170
— P1815 MANU MODE SW/CIRCAT-172
— P1841 ATF PRES SW 1/CIRCAT-178
— P1843 ATF PRES SW 3/CIRCAT-180
— P1845 ATF PRES SW 5/CIRCAT-182
— P1846 ATF PRES SW 6/CIRCAT-184
U1000 U1000 CAN COMM CIRCUITAT-105

AT-8
PRECAUTIONS
Revision: 2004 November 2004 FX35/FX45
Precautions ACS002L6

Before connecting or disconnecting the A/T assembly har-
ness connector, turn ignition switch “OFF” and disconnect
the battery cable from the negative terminal. Because bat-
tery voltage is applied to TCM even if ignition switch is
turned “OFF”.

After performing each TROUBLE DIAGNOSIS, perform
“DTC (Diagnostic Trouble Code) Confirmation Procedure”.
If the repair is completed the DTC should not be displayed
in the “DTC Confirmation Procedure”.

Always use the specified brand of ATF. Refer to MA-12, "Fluids and Lubricants" .

Use paper rags not cloth rags during work.

After replacing the ATF, dispose of the waste oil using the methods prescribed by law, ordinance, etc.

Before proceeding with disassembly, thoroughly clean the outside of the transmission. It is important to
prevent the internal parts from becoming contaminated by dirt or other foreign matter.

Disassembly should be done in a clean work area.

Use lint-free cloth or towels for wiping parts clean. Common shop rags can leave fibers that could interfere
with the operation of the transmission.

Place disassembled parts in order for easier and proper assembly.

All parts should be carefully cleaned with a general purpose, non-flammable solvent before inspection or
reassembly.

Gaskets, seals and O-rings should be replaced any time the transmission is disassembled.

It is very important to perform functional tests whenever they are indicated.

The valve body contains precision parts and requires extreme care when parts are removed and serviced.
Place disassembled valve body parts in order for easier and proper assembly. Care will also prevent
springs and small parts from becoming scattered or lost.

Properly installed valves, sleeves, plugs, etc. will slide along bores in valve body under their own weight.

Before assembly, apply a coat of recommended ATF to all parts. Apply petroleum jelly to protect O-rings
and seals, or hold bearings and washers in place during assembly. Do not use grease.

Extreme care should be taken to avoid damage to O-rings, seals and gaskets when assembling.

After overhaul, refill the transmission with new ATF.

When the A/T drain plug is removed, only some of the fluid is drained. Old A/T fluid will remain in torque
converter and ATF cooling system.
Always follow the procedures under “Changing A/T Fluid” in the AT section when changing A/T fluid. Refer
to AT- 1 2 , "
Changing A/T Fluid" , AT- 1 2 , "Checking A/T Fluid" .
SEF289H
SEF217U

PRECAUTIONS
AT-9
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
Service Notice or PrecautionsACS002L7
ATF COOLER SERVICE
If A/T fluid contains frictional material (clutches, bands, etc.), or if an A/T is repaired, overhauled, or replaced,
inspect and clean the A/T fluid cooler mounted in the radiator or replace the radiator. Flush cooler lines using
cleaning solvent and compressed air after repair. For A/T fluid cooler cleaning procedure, refer to AT- 1 4 , "
A/T
Fluid Cooler Cleaning" . For radiator replacement, refer to CO-14, "RADIATOR" (for VQ35DE) or CO-39,
"RADIATOR" (for VK45DE).
OBD-II SELF-DIAGNOSIS

A/T self-diagnosis is performed by the TCM in combination with the ECM. The results can be read through
the blinking pattern of the A/T CHECK indicator or the malfunction indicator lamp (MIL). Refer to the table
on AT- 9 4 , "
SELF-DIAGNOSTIC RESULT MODE" for the indicator used to display each self-diagnostic
result.

The self-diagnostic results indicated by the MIL are automatically stored in both the ECM and TCM mem-
ories.
Always perform the procedure on AT- 3 9 , "
HOW TO ERASE DTC" to complete the repair and avoid
unnecessary blinking of the MIL.
For details of OBD-II, refer to EC-53, "
ON BOARD DIAGNOSTIC (OBD) SYSTEM" (for VQ35DE) or EC-703,
"ON BOARD DIAGNOSTIC (OBD) SYSTEM" (for VK45DE).

Certain systems and components, especially those related to OBD, may use the new style slide-
locking type harness connector. For description and how to disconnect, refer to PG-74, "
HAR-
NESS CONNECTOR" .
Wiring Diagrams and Trouble DiagnosisACS002L8
When you read wiring diagrams, refer to the following:

GI-15, "How to Read Wiring Diagrams".

PG-3, "POWER SUPPLY ROUTING CIRCUIT" for power distribution circuit.
When you perform trouble diagnosis, refer to the following:

GI-11, "How to Follow Trouble Diagnoses".

GI-27, "How to Perform Efficient Diagnosis for an Electrical Incident".

AT-38
ON BOARD DIAGNOSTIC (OBD) SYSTEM
Revision: 2004 November 2004 FX35/FX45
ON BOARD DIAGNOSTIC (OBD) SYSTEMPFP:00028
IntroductionACS002LN
The A/T system has two self-diagnostic systems.
The first is the emission-related on board diagnostic system (OBD-II) performed by the TCM in combination
with the ECM. The malfunction is indicated by the MIL (malfunction indicator lamp) and is stored as a DTC in
the ECM memory but not the TCM memory.
The second is the TCM original self-diagnosis indicated by the A/T CHECK indicator lamp. The malfunction is
stored in the TCM memory. The detected items are overlapped with OBD-II self-diagnostic items. For detail,
refer to AT- 9 4 , "
Display Items List" .
OBD-II Function for A/T SystemACS002LO
The ECM provides emission-related on board diagnostic (OBD-II) functions for the A/T system. One function
is to receive a signal from the TCM used with OBD-related parts of the A/T system. The signal is sent to the
ECM when a malfunction occurs in the corresponding OBD-related part. The other function is to indicate a
diagnostic result by means of the MIL (malfunction indicator lamp) on the instrument panel. Sensors, switches
and solenoid valves are used as sensing elements.
The MIL automatically illuminates in One or Two Trip Detection Logic when a malfunction is sensed in relation
to A/T system parts.
One or Two Trip Detection Logic of OBD-IIACS002LP
ONE TRIP DETECTION LOGIC
If a malfunction is sensed during the first test drive, the MIL will illuminate and the malfunction will be stored in
the ECM memory as a DTC. The TCM is not provided with such a memory function.
TWO TRIP DETECTION LOGIC
When a malfunction is sensed during the first test drive, it is stored in the ECM memory as a 1st trip DTC
(diagnostic trouble code) or 1st trip freeze frame data. At this point, the MIL will not illuminate. — First Trip
If the same malfunction as that experienced during the first test drive is sensed during the second test drive,
the MIL will illuminate. — Second Trip
The “Trip” in the “One or Two Trip Detection Logic” means a driving mode in which self-diagnosis is performed
during vehicle operation.
OBD-II Diagnostic Trouble Code (DTC)ACS002LQ
HOW TO READ DTC AND 1ST TRIP DTC
DTC and 1st trip DTC can be read by the following methods.
( with CONSULT-II or GST) CONSULT-II or GST (Generic Scan Tool) Examples: P0705, P0720 etc.
These DTC are prescribed by SAE J2012.
(CONSULT-II also displays the malfunctioning component or system.)

1st trip DTC No. is the same as DTC No.

Output of the diagnostic trouble code indicates that the indicated circuit has a malfunction. How-
ever, in case of the Mode II and GST, they do not indicate whether the malfunction is still occurring
or occurred in the past and returned to normal.
CONSULT-II can identify them as shown below, therefore, CONSULT-II (if available) is recom-
mended.
A sample of CONSULT-II display for DTC and 1st trip DTC is shown
on the next page. DTC or 1st trip DTC of a malfunction is displayed
in SELF-DIAGNOSTIC RESULTS mode for “ENGINE” with CON-
SULT-II. Time data indicates how many times the vehicle was driven
after the last detection of a DTC.
SAT014K

ON BOARD DIAGNOSTIC (OBD) SYSTEM
AT-39
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
If the DTC is being detected currently, the time data will be “0”.
If a 1st trip DTC is stored in the ECM, the time data will be “1t”.
Freeze Frame Data and 1st Trip Freeze Frame Data
The ECM has a memory function, which stores the driving condition such as fuel system status, calculated
load value, engine coolant temperature, short term fuel trim, long term fuel trim, engine speed and vehicle
speed at the moment the ECM detects a malfunction.
Data which are stored in the ECM memory, along with the 1st trip DTC, are called 1st trip freeze frame data,
and the data, stored together with the DTC data, are called freeze frame data and displayed on CONSULT-II
or GST. The 1st trip freeze frame data can only be displayed on the CONSULT-II screen, not on the GST. For
detail, refer to EC-109, "
CONSULT-II Function" (for VQ35DE) or EC-759, "CONSULT-II Function" (for
VK45DE).
Only one set of freeze frame data (either 1st trip freeze frame data of freeze frame data) can be stored in the
ECM. 1st trip freeze frame data is stored in the ECM memory along with the 1st trip DTC. There is no priority
for 1st trip freeze frame data and it is updated each time a different 1st trip DTC is detected. However, once
freeze frame data (2nd trip detection/MIL on) is stored in the ECM memory, 1st trip freeze frame data is no
longer stored. Remember, only one set of freeze frame data can be stored in the ECM. The ECM has the fol-
lowing priorities to update the data.
Both 1st trip freeze frame data and freeze frame data (along with the DTC) are cleared when the ECM mem-
ory is erased.
HOW TO ERASE DTC
The diagnostic trouble code can be erased by CONSULT-II, GST or ECM DIAGNOSTIC TEST MODE as
described following.

If the battery cable is disconnected, the diagnostic trouble code will be lost within 24 hours.

When you erase the DTC, using CONSULT-II or GST is easier and quicker than switching the mode
selector on the ECM.
The following emission-related diagnostic information is cleared from the ECM memory when erasing DTC
related to OBD-II. For details, refer to EC-54, "
Emission-Related Diagnostic Information" (for VQ35DE) or EC-
704, "Emission-related Diagnostic Information" (for VK45DE).

Diagnostic trouble codes (DTC)
SAT015K
SAT016K
Priority Items
1 Freeze frame data Misfire — DTC: P0300 - P0306
Fuel Injection System Function — DTC: P0171, P0172, P0174, P0175
2 Except the above items (Includes A/T related items)
3 1st trip freeze frame data

AT-40
ON BOARD DIAGNOSTIC (OBD) SYSTEM
Revision: 2004 November 2004 FX35/FX45

1st trip diagnostic trouble codes (1st trip DTC)

Freeze frame data

1st trip freeze frame data

System readiness test (SRT) codes

Test values
HOW TO ERASE DTC (WITH CONSULT-II)

If a DTC is displayed for both ECM and TCM, it is necessary to be erased for both ECM and TCM.
1. If the ignition switch stays “ON” after repair work, be sure to turn ignition switch “OFF” once. Wait at least
10 seconds and then turn it “ON” (engine stopped) again.
2. Turn CONSULT-II “ON” and touch “A/T”.
3. Touch “SELF-DIAG RESULTS”.
4. Touch “ERASE”. (The DTC in the TCM will be erased.) Then touch “BACK” twice.
5. Touch “ENGINE”.
6. Touch “SELF-DIAG RESULTS”.
7. Touch “ERASE”. (The DTC in the ECM will be erased.)
HOW TO ERASE DTC (WITH GST)
1. If the ignition switch stays “ON” after repair work, be sure to turn ignition switch “OFF” once. Wait at least
10 seconds and then turn it “ON” (engine stopped) again.
2. Perform “TCM SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)”. Refer to AT- 1 0 3 , "
TCM SELF-DIAG-
NOSTIC PROCEDURE (NO TOOLS)" . (The engine warm-up step can be skipped when performing the
diagnosis only to erase the DTC.)
3. Select Mode 4 with Generic Scan Tool (GST). For details, refer to EC-122, "
Generic Scan Tool (GST)
Function" (for VQ35DE) or EC-772, "Generic Scan Tool (GST) Function" (for VK45DE).
SCIA5671E