lan s INFINITI FX35 2004 Service Manual

RFD-16
REAR FINAL DRIVE ASSEMBLY
Revision: 2004 November 2004 FX35/FX45
3. Remove companion flange using the suitable puller .
4. Take out drive pinion (together with rear bearing inner race, pin-
ion bearing adjusting spacer).
5. Remove front oil seal. Refer to RFD-7, "
FRONT OIL SEAL" .
6. Remove pinion front bearing inner race.
7. Remove side oil seal. Refer to RFD-9, "
SIDE OIL SEAL" .
8. Remove pinion bearing outer races with a brass drift.
9. Remove pinion rear bearing inner race and drive pinion height
adjusting washer with tool.
SDIA1129E
SPD892
SDIA0817E
Tool number : ST30031000 (J22912 - 01)
S-PD179

REAR FINAL DRIVE ASSEMBLY
RFD-19
C
E
F
G
H
I
J
K
L
MA
B
RFD
Revision: 2004 November 2004 FX35/FX45
ADJUSTMENT OF DIFFERENTIAL CASE
Thrust Washer Selection
1. Apply gear oil to contact surfaces of each gear, thrust washers
and differential case.
2. Install the removed thrust washer or same thickness washer to
side gear.
3. Install the side gears, thrust washers, pinion mate gears, thrust
washers into differential case.
CAUTION:
Install the circlip equipped side gear to the side retainer
side.
4. Fit pinion mate shaft to differential case so that it meets lock pin
holes.
Side gear thrust washer and
pinion mate thrust washer
Replace with a new one if found any cracks or damage on the surface of the tooth.

Replace with a new one if found any worn or chipped mark on the contact sides of the thrust
washer.
Side gear and pinion mate
thrust washer

Replace with a new one if found that it is chipped (by friction), damaged, or unusual worn.
Oil seal

Oil seals must be replaced with a new one whenever disassembled.
Differential case

Replace with a new one if found any wear or cracks on the contact sides of the differential case.
Companion flange

Replace with a new one if found any chipped marks (about 0.10mm, 0.0039in) or other damage
on the contact sides of the lips of the companion flange. Content Measures
SDIA0193J
SPD552
SDIA0195J

REAR FINAL DRIVE ASSEMBLY
RFD-25
C
E
F
G
H
I
J
K
L
MA
B
RFD
Revision: 2004 November 2004 FX35/FX45
1. Thoroughly clean drive gear and drive pinion teeth.
2. Lightly apply a mixture of powdered ferric oxide and oil or the
equivalent. Apply it to 3 or 4 teeth of drive gear drive side.
3. Hold companion flange steady by hand and rotate the drive gear
in both directions.
ASSEMBLY OF DIFFERENTIAL CASE ASSEMBLY
1. Install pinion mate shaft lock pin with a punch.
Make sure lock pin is flush with case.
CAUTION:
Do not reuse the lock pin. Always replace the lock pin with
a new one.
SPD357
SDIA0813E
SDIA1796E
SPD030

RFD-26
REAR FINAL DRIVE ASSEMBLY
Revision: 2004 November 2004 FX35/FX45
2. Place differential case on drive gear.
3. Apply genuine medium strength locking sealant or equivalent.
Refer to GI-48, "
RECOMMENDED CHEMICAL PRODUCTS
AND SEALANTS" to drive gear bolts, and install them.
CAUTION:
Do not reuse the bolts. Always replace the bolts with a new
one.

Tighten bolts in a crisscross fashion.

After tightening the bolt to the specified torque, turn the bolt
31 to 36 more degrees.
4. Press-fit side bearing inner race on differential case with tool.
INSTALLATION OF DRIVE PINION ASSEMBLY
1. Press-fit front and rear bearing outer races with tools.
2. Select drive pinion height adjusting washer. Refer to RFD-31, "
AVAILABLE PINION HEIGHT ADJUSTING
WASHERS"
SPD554
Tool number A : KV38100300 (J25523)
B : ST33061000 (J8107-2)
SPD353
Tool number A : Suitable tool
B : ST30611000 (J25742-1)
C : ST30613000 (J25742-3)
SPD992

REAR FINAL DRIVE ASSEMBLY
RFD-27
C
E
F
G
H
I
J
K
L
MA
B
RFD
Revision: 2004 November 2004 FX35/FX45
3. Install selected drive pinion height adjusting washer in drive pin-
ion. Using hydraulic press and tool, press-fit pinion rear bearing
inner race into it.
4. Apply multi-purpose grease to pinion rear bearing inner race
and pinion front bearing inner race.
5. Set drive pinion assembly (as shown in figure) in differential car-
rier and install drive pinion, with press and suitable tool.
Stop when drive pinion touches bearing.
6. Install front oil seal with tool. Refer to RFD-7, "
Removal and Installation" .
7. Install companion flange, and tighten drive pinion lock nut to
minimum.
Ascertain that threaded portion of drive pinion and drive pinion
lock nut are free from oil.
CAUTION:
The drive pinion lock nut is not reusable. Never reuse drive
pinion lock nut.Tool number : ST30901000 ( – )
SPD377
SDIA1797E
SPD896
Tool number : ST30720000 (J25405)
Tool number : KV40104000 ( – )
SDIA1011E

RFD-30
REAR FINAL DRIVE ASSEMBLY
Revision: 2004 November 2004 FX35/FX45
12. Install rear cover. Apply liquid sealant to rear cover side and
install gear carrier.
SDIA0970E

RFD-32
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: 2004 November 2004 FX35/FX45
Side Bearing Preload Adjustment ADS000K0
SIDE BEARING ADJUSTING WASHERS
Unit: mm (in)
*: Always check with the Parts Department for the latest parts information.
Total Preload AdjustmentADS000K1
Companion FlangeADS000OC
Type R200
Side bearing preload <Reference> 0.20 − 0.52 N·m (0.02 − 0.05 kg−m, 2 − 4 in-lb)
Torque by spring gauge 34.2 − 39.2 N (3.5 − 4.0 kg, 7.7 − 8.8 lb)
Type R200
Adjusting washerThickness Part number* Thickness Part number*
2.00 (0.0787) 38453 N3100 2.35 (0.0925) 38453 N3107
2.05 (0.0807) 38453 N3101 2.40 (0.0945) 38453 N3108
2.10 (0.0827) 38453 N3102 2.45 (0.0965) 38453 N3109
2.15 (0.0846) 38453 N3103 2.50 (0.0984) 38453 N3110
2.20 (0.0866) 38453 N3104 2.55 (0.1004) 38453 N3111
2.25 (0.0886) 38453 N3105 2.60 (0.1024) 38453 N3112
2.30 (0.0906) 38453 N3106 2.65 (0.1043) 38453 N3113
Type R200
Total preload (with oil seal) 2.84 − 3.75 N·m (0.29 − 0.38 kg−m, 26 − 33 in-lb)
Drive gear to drive pinion backlash 0.10 − 0.15 mm (0.0039 − 0.0059 in)
Type R200
Runout limit0.13 mm (0.0051 in)

RSU-2
PRECAUTIONS
Revision: 2004 November 2004 FX35/FX45
PRECAUTIONSPFP:00001
CautionsAES000MF

When installing rubber bushings, final tightening must be carried out under unladen conditions with tires
on level ground. Oil will shorten the life of rubber bushings. Be sure to wipe off any spilled oil.

Unladen conditions means that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.

After servicing suspension parts, be sure to check wheel alignment.

Caulking nuts are not reusable. Always use new ones when installing. Since new caulking nuts are pre-
oiled, tighten as they are.

REAR SUSPENSION ASSEMBLY
RSU-5
C
D
F
G
H
I
J
K
L
MA
B
RSU
Revision: 2004 November 2004 FX35/FX45
REAR SUSPENSION ASSEMBLYPFP:55020
On-Vehicle Inspection and ServiceAES000MJ
Make sure the mounting conditions (looseness, back lash) of each component and component status (wear,
damage) are normal.
INSPECTION OF SUSPENSION ARM BALL JOINT END PLAY
Measure axial end play by installing and moving up/down between suspension arm and axle with an iron pry
bar or something similar.
CAUTION:
Be careful not to damage ball joint boot.
SHOCK ABSORBER INSPECTION
Check shock absorber for oil leakage, damage and replace if necessary.
Wheel Alignment InspectionAES000MK
DESCRIPTION
Measure wheel alignment under unladen conditions. “Unladen conditions” mean that fuel, engine coolant, and
lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
PRELIMINARY CHECK
1. Check tires for improper air pressure and wear.
2. Check road wheels for runout.
3. Check wheel bearing axial end play.
4. Check suspension arm ball joint axial end play.
5. Check shock absorber operation.
6. Check each mounting part of axle and suspension for looseness and deformation.
7. Check each link, arm and member for cracks, deformation, and other damage.
8. Check vehicle posture.
CAMBER INSPECTION
Measure camber of both right and left wheels with a suitable align-
ment gauge and adjust in accordance with the following procedures.
If outside the standard value, adjust with adjusting bolt in front lower
link.
NOTE:
After adjusting camber, be sure to check toe-in.Axial end play : 0 mm (0 in)
Camber : Refer to RSU-18, "
Wheel Alignment" .
SRA096A
SEIA0318E

RSU-18
SERVICE DATA
Revision: 2004 November 2004 FX35/FX45
SERVICE DATAPFP:00030
Wheel AlignmentAES000MV
Ball JointAES000MW
Wheelarch Height (Unladen*)AES000MX
*: Fuel, engine coolant and engine oil full. Spare tire, jack, hand tools and mats are in designated positions.Camber
Degree minute (Decimal degree)Minimum – 1° 18′ (– 1.30°)
Nominal – 0° 48′ (– 0.80°)
Maximum – 0° 18′ (– 0.30°)
Total toe-inDistance (A – B)Minimum 2.4 mm (0.094 in)
Nominal 4.7 mm (0.185 in)
Maximum 7.0 mm (0.276 in)
Angle (left plus right)
Degree minute (Degree)Minimum 0°05′ (0.08°)
Nominal 0°10′ (0.17°)
Maximum 0°15′ (0.25°)
Axial end play0 mm (0 in)
Swing torque 0.5 − 3.4 N·m (0.06 − 0.34 kg-m, 5 − 30 in-lb)
Measurement on spring balance (cotter pinhole position) 9.7 − 66.0 N (0.99 − 6.7 kg, 2.18 − 14.8 lb)
Rotating torque 0.5 − 3.4 N·m (0.06 − 0.34 kg-m, 5 − 30 in-lb)
Destination USA Canada
Engine VQ35DE VK45DE VQ35DE VK45DE
Axle 2WD AWD AWD
Tire size 265/60R18 265/50R20 265/60R18 265/50R20 265/60R18 265/50R20
Front (Hf)835 mm
(32.87 in)834 mm
(32.83 in)834 mm
(32.83 in)833 mm
(32.80 in)832 mm
(32.76 in)834 mm
(32.83 in)833 mm
(32.80 in)832 mm
(32.76 in)
Rear (Hr)822 mm
(32.36 in)821 mm
(32.32 in)829 mm
(32.64 in)827 mm
(32.56 in)825 mm
(32.48 in)827 mm
(32.56 in)826 mm
(32.52 in)823 mm
(32.40 in)
SFA818A