Button INFINITI QX30 2017 Repair Manual

2. The rear view of the vehicle is displayed onthe screen
Aas illustrated when the shift
lever is moved to the R (Reverse) position.
3. Slowly back up the vehicle adjusting thesteering wheel so that the predicted course
lines
Benter the parking spaceC. 4. When the rear of the vehicle enters the
parking space
C, maneuver the steering
wheel to make the vehicle width guide lines
Dparallel to the parking spaceC.
5. When the vehicle is parked in the space completely, press the P (Park) button and
apply the parking brake.
HOW TO SWITCH THE DISPLAY
The view on the Around View Monitor screen
can be switched by pressing the <CAMERA>
button or by changing the shift lever position.
Press the <CAMERA> button:
When the <CAMERA> button is pushed while a
screen other than a camera screen is displayed,
the Around View Monitor operates and the front
view and bird’s-eye view are displayed. Push
the <CAMERA> button to switch the display to
the front view and front-side view screen.
SAA1898
Display screen, heater and air conditioner, and audio system4-31

ADJUSTING THE SCREEN
1. Push the<MENU>buttonBon the INFINITI
Controller and touch [Settings]
Ain the
vehicle information display.
2. Touch [Camera]/[Sonar]
3. Touch [Display]
4. Select the item you wish to adjust:
[Brightness]:
Adjust display settings by touching [+]/[-].
[Contrast]:
Adjust display settings by touching [+]/[-].
[Black level]:
Adjust display settings by touching [+]/[-].
[Tint]:
Adjust display settings by touching [+]/[-].
[Color]:
Adjust display settings by touching [+]/[-].
[Reset Settings]:
Return all the settings to default NOTE
Do not adjust any of the display settings of the
Around View Monitor while the vehicle is mov-
ing. Make sure the parking brake is firmly
applied.
4-32Display screen, heater and air conditioner, and audio system

A[Settings] key
B<MENU> button
AROUND VIEW MONITOR SETTING
Around View Monitor settings can be changed
using the following procedure:
1. Push the<MENU>button
Bon the INFINITI
Controller and touch [Settings]
Ain the
vehicle information display.
2. Touch [Camera]/[Sonar]
3. Touch [Camera]
4. Touch [Moving Object Detection] Activate or deactivate the Moving Object
Detection (MOD) mode.
AROUND VIEW®MONITOR SYSTEM
LIMITATIONS
WARNING
Listed below are the system limitations for
Around View Monitor. Failure to operate the
vehicle in accordance with these system limi-
tations could result in serious injury or death.
•Do not use the Around View Monitor with
the outside mirror in the stored position,
and make sure that the lift gate is securely
closed when operating the vehicle using the
Around View Monitor.
NSD628
Display screen, heater and air conditioner, and audio system4-33

SYSTEM MAINTENANCE
CAUTION
•Do not use alcohol, benzine or thinner to
clean the camera. This will cause discolor-
ation. To clean the camera, wipe with a cloth
dampened with diluted mild cleaning agent
and then wipe with a dry cloth.
•Do not damage the camera as the monitor
screen may be adversely affected.
If dirt, rain or snow accumulates on any of the
cameras, the Around View Monitor may not
display objects clearly. Clean the cameras by
wiping with a cloth dampened with a diluted
mild cleaning agent and then wiping with a dry
cloth.
A[Settings] key
B<MENU> buttonSONAR FUNCTION SETTINGS (IF SO
EQUIPPED)
The sonar function settings can be changed
using the following procedure.
1. Push <MENU>
Band touch [Settings]A.
NAA1638
NSD628
4-36Display screen, heater and air conditioner, and audio system

2. Touch [Camera/Sonar]
3. Touch [Sonar]
[Sonar sensitivity]:
Adjust the sonar sensor sensitivity level by
touching [+]/[-].
[Sonar volume]:
Adjust the buzzer volume by touching [+]/[-].
AAround View Monitor display
BINFINITI controller
C<MENU> button
D<CAMERA> button
WARNING
Failure to follow the warnings and instructions
for proper use of the Moving Object Detection
system could result in serious injury or death.
NSD651
MOVING OBJECT DETECTION (IF SO
EQUIPPED)
Display screen, heater and air conditioner, and audio system4-37

•The MOD system is not a substitute for
proper vehicle operation and is not de-
signed to prevent contact with objects sur-
rounding the vehicle. When maneuvering,
always use the outside mirror and rearview
mirror and turn and check the surroundings
to ensure it is safe to maneuver.
•The system is deactivated at speeds above 5
MPH (8 km/h). It is reactivated at lower
speeds.
•The MOD system is not designed to detect
the surrounding stationary objects.
The Moving Object Detection (MOD) system can
inform the driver of moving objects surrounding
the vehicle when driving out of garages, maneu-
vering into parking lots and in other such
instances.
The MOD system detects moving objects by
using image processing technology on the im-
age shown on the display.
MOD SYSTEM OPERATION
The MOD system will activate automatically
under the following conditions:
•When the shift lever is in the R (Reverse)
position.
•When the <CAMERA> button is pressed to
switch from a different screen to the camera
view on the display.
•When vehicle speed decreases below ap-
proximately 5 MPH (8 km/h).
•When the ignition switch is placed in the OFF
position and then back to the ON position.
NOTE
•The MOD system does not detect moving
objects in the front-side view. The MOD icon
is not displayed on the screen when in this
view.
•While the parking sensor warning tone is
sounding, the MOD system does not chime. The MOD system operates in the following
conditions when the camera view is displayed:
When the shift lever is in the R (Reverse)
position and the vehicle speed is approximately
5 MPH (8 km/h ) or less, the MOD system
detects moving objects in the camera view. The
MOD system will not operate if the lift gate is
open.
When the MOD system detects moving objects
near the vehicle, a chime will be heard and a
yellow frame
1will be displayed on the moni-
tor.
While the MOD system continues to detect
moving objects, the yellow frame continues to
be displayed.
The yellow frame
1is displayed on each view
in the rear view modes.
NAA1781Bird’s-eye view
4-38Display screen, heater and air conditioner, and audio system

A blue<MOD>icon is displayed in the view
where the MOD system is operative. A gray
MOD icon is displayed in the view where the
MOD system is not operative.
A[Settings] key
B<MENU> button
MOD SETTING
MOD system settings can be changed using the
following procedure. 1. Push the <MENU> button
Bon the INFINITI
Controller and touch [Settings]
Ain the
vehicle information display.
2. Touch [Camera/Sonar]
3. Touch [Camera]
NAA1782Front view / rear view
NSD628
Display screen, heater and air conditioner, and audio system4-39

Recommendation for air distribution in sum-
mer: select theorandsettings.
•Only use theWindshield demisting function
briefly until the windshield is clear again
•Only use air-recirculation mode briefly, e. g if
there are unpleasant outside odors or when
in a tunnel. The windows could otherwise
mist up as no fresh air is drawn into the
vehicle in air-recirculation mode
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds at
the bottom of the screen in the central
display (see separate operating instruc-
tions). You will see the current settings of the
various climate control functions.
Switching air-conditioning system
on/off
Make sure the ignition switch is in the ON
position.
To switch on: turn control
5clockwise to the
desired position (except position 0).
To switch off: turn control
5counter-clockwise
to position 0.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate the Cooling with air dehumidi-
fication function, the air inside the vehicle will
not be cooled. The air inside the vehicle will
also not be dehumidified. The windows can mist
up more quickly. Therefore, only deactivate the
Cooling with air dehumidification function
briefly.
The Cooling with air dehumidification function
is only available when the engine is running.
The air inside the vehicle is cooled and dehu-
midified according to the temperature selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This is
normal and not a sign that there is a malfunc-
tion.
To activate
:
Press thebutton The indicator lamp in
thebutton lights up.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton goes out. The cooling with air
dehumidification function has a delayed switch-
off feature. Problems with the
Cooling with air dehumidifi-
cation function
:
Problem: The indicator lamp in thebutton flashes three times or remains off. The
cooling with air dehumidification function can-
not be activated.
Cause and solution: The cooling with air dehu-
midification function has been deactivated due
to a malfunction. Have the system checked. It is
recommended you visit an INFINITI retailer for
this service.
Setting the temperature
You can set the temperature for the entire
vehicle. The set temperature is automatically
maintained at a constant level.
To increase or reduce the temperature: turn
control
1counterclockwise or clockwise. Only
change the temperature setting in small incre-
ments. Start at 70
oF (22oC).
Setting the air distribution
Directs the airflow through the demister ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the footwell
air ventilators.
4-44Display screen, heater and air conditioner, and audio system

NOTE
•You can also activate several of the air
distribution settings simultaneously. In order
to do this, press several of the air distribu-
tion buttons. The air is then routed through
different air ventilators.
•Regardless of the air distribution setting,
airflow is always directed through the side
air ventilators. The side air ventilators can
only be closed if the adjusters are turned
clockwise until they engage.
To set air distribution:
1. Make sure the engine is running.
2. Press one or more of the
,,orbuttons. The corresponding indicator
lamp comes on.
Setting the airflow
1. Make sure the ignition switch is in the ON position.
2. To increase or reduce airflow: turn control
5counterclockwise or clockwise.
Defogging the windshield
You can use this function to de-ice the wind-
shield or to defog the inside of the windshield
and the side windows. NOTE
You should only select the
Windshield demist-
ing function until the windshield is clear again.
Activating the Windshield demisting function
:
Make sure the ignition switch is in the ON
position.
To activate: press the
button The indica-
tor light in thebutton lights up.
The climate control system switches to the
following functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air-recirculation mode off
NOTE
•The Windshield demisting function auto-
matically sets the blower output to the opti-
mum demisting effect. As a result, the airflow
may increase or decrease automatically after
the
button is pressed.
•You can adjust the blower output manually
while the Windshield demisting function is
in operation. Turn airflow control
5counter-
clockwise or clockwise. Deactivating the
Windshield demisting func-
tion
:
Press thebutton. The indicator lamp in
thebutton goes out. The previous set-
tings are reactivated. Air-recirculation mode
remains deactivated.
or
Turn temperature control
1counterclockwise
or clockwise.
Defogging the windows
Windows misted up on the inside:
1. Activate theCooling with air dehu-
midification function.
2. If the windows continue to mist up, activate the
Windshield demisting function.
NOTE
You should only select this setting until the
windshield is clear again.
Windows misted up on the outside
:
1. Activate the windshield wipers.
2. Set the air distribution to
or.
NOTE
You should only select this setting until the win-
dows are clear again.
Display screen, heater and air conditioner, and audio system4-45

Air recirculation mode
You can deactivate the flow of fresh air if
unpleasant odors are entering the vehicle from
outside. The air already inside the vehicle will
then be recirculated.
If you activate air-recirculation mode, the win-
dows can mist up more quickly, in particular at
low temperatures. Only use air recirculation
mode briefly to prevent the windows misting
up.
Activating air recirculation mode
:
Make sure the ignition switch is in the ON
position.
Press the
button. The indicator light in
thebutton lights up.
Deactivating air recirculation mode
:
Press thebutton. The indicator light in
thebutton goes out.
NOTE
Air-recirculation mode is deactivated automati-
cally:
•After approximately five minutes at outside
temperatures below approximately 45oF
(7oC).
•After approximately five minutes if the Cool-
ing with air dehumidification function is
deactivated.
•After approximately 30 minutes at outside
temperatures above approximately 45oF
(7oC) if the cooling with air dehumidification
function is activated.
Idle Stop/Start function
During automatic engine switch-off, the Climate
control only operates at a reduced capacity. If
you require the full climate control output, you
can switch off the Idle Stop/Start function by
pressing the ECO button (see Idle Stop/Start
System (if equipped) in the5. Starting and
driving section).
4-46Display screen, heater and air conditioner, and audio system