brake INFINITI QX56 2006 Factory Manual Online

TROUBLE DIAGNOSISAT-79
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX5653
Others Vehicle dose not
decelerate by engine
brake.
Refer to
AT-218,
"Vehicle Does Not
Decelerate By Engine
Brake" . ON vehicle
1. PNP switch
AT-105
2. Fluid level and state AT- 5 1
3. Control cable adjustmentAT-227
4. 1st position switchAT-218
5. ATF pressure switch 5AT-163
6. CAN communication line AT- 9 6
7. Control valve with TCMAT-230
OFF vehicle8. Input clutch
AT-2869. High and low reverse clutchAT-296
10. Direct clutchAT-298
54Engine brake does
not operate in
“2 ”
position. ON vehicle1. PNP switch
AT-105
2. Fluid level and state AT- 5 1
3. Control cable adjustmentAT-227
5. ATF pressure switch 6AT-165
6. CAN communication line AT- 9 6
7. Control valve with TCMAT-230
OFF vehicle8. Front brake (brake band)
AT-2649. Input clutchAT-286
10. High and low reverse clutchAT-296
55Engine brake does
not operate in
“1 ”
position. ON vehicle1. PNP switch
AT-105
2. Fluid level and state AT- 5 1
3. Control cable adjustmentAT-227
4. 1st position switchAT-218
5. ATF pressure switch 5AT-163
6. CAN communication line AT- 9 6
7. Control valve with TCMAT-230
OFF vehicle8. Input clutch
AT-2869. High and low reverse clutchAT-296
10. Direct clutchAT-298
No. ItemsSymptom Condition Diagnostic ItemReference
page

AT-80
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
56
Others Maximum speed low.
ON vehicle
1. Fluid level and state
AT- 5 1
2. Line pressure testAT- 5 2
3. Accelerator pedal position sensorAT- 1 2 4
4. CAN communication line AT- 9 6
5. Direct clutch solenoid valveAT- 1 4 7
6. Control valve with TCMAT- 2 3 0
OFF vehicle7. Torque converter
AT- 2 6 4
8. Oil pump assemblyAT- 2 8 2
9. Input clutchAT- 2 8 6
10. Gear systemAT- 2 5 0
11. High and low reverse clutchAT- 2 9 6
12. Direct clutchAT- 2 9 8
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 7
, AT- 1 8 .) AT- 2 6 4
14 Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to
AT- 1 7
, AT- 1 8
.) AT- 2 6 4
57
Extremely large
creep. ON vehicle1. Engine idle speed
EC-76

2. CAN communication line AT- 9 6
3. ATF pressure switch 5AT- 1 6 3
OFF vehicle 4. Torque converter AT- 2 6 4
58With selector lever in
“
P ” position, vehicle
does not enter parking
condition or, with
selector lever in
another position, park-
ing condition is not
cancelled.
Refer to AT-180, "
In
“P” Position, Vehicle
Moves When Pushed"
. ON vehicle
1. PNP switch
AT- 1 0 5
2. Control cable adjustmentAT- 2 2 7
OFF vehicle 3. Parking pawl components AT- 2 5 0
59Vehicle runs with
transmission in
“P ”
position. ON vehicle1. PNP switch
AT- 1 0 5
2. Fluid level and state AT- 5 1
3. Control cable adjustmentAT- 2 2 7
4. Control valve with TCMAT- 2 3 0
5. Parking pawl componentsAT- 2 5 0
OFF vehicle 6. Gear system AT- 2 5 0
No. ItemsSymptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSISAT-81
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
60
Others Vehicle runs with
transmission in
“N ”
position.
Refer to AT-181, "In
“N” Position, Vehicle
Moves" . ON vehicle
1. PNP switch
AT-105
2. Fluid level and state AT- 5 1
3. Control cable adjustmentAT-227
4. Control valve with TCMAT-230
OFF vehicle5. Input clutch
AT-286
6. Gear systemAT-250
7. Direct clutchAT-298
8. Reverse brakeAT-264
9. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 7
, AT- 1 8 .) AT-264
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 7
, AT- 1 8
.) AT-264
61Engine does not start
in
“N ” or “P ” position.
Refer to AT-179, "Engine Cannot Be
Started In “P” or “N”
Position" . ON vehicle
1. Ignition switch and starter
PG-4
, SC-
10
2. Control cable adjustment
AT-227
3. PNP switchAT-105
62Engine starts in posi-
tions other than “
N” or
“ P ”. ON vehicle1. Ignition switch and starter
PG-4
, SC-
10
2. Control cable adjustment
AT-227
3. PNP switchAT-105
63Engine stall. ON vehicle1. Fluid level and state
AT- 5 1
2. Engine speed signalAT- 11 6
3. Turbine revolution sensorAT-109
4. Torque converter clutch solenoid valve AT- 11 8
5. CAN communication line AT- 9 6
6. Control valve with TCMAT-230
OFF vehicle 7. Torque converter AT-264
64Engine stalls when
select lever shifted
“N ”
→ “ D ”, “ R”. ON vehicle1. Fluid level and state
AT- 5 1
2. Engine speed signalAT- 11 6
3. Turbine revolution sensorAT-109
4. Torque converter clutch solenoid valve AT- 11 8
5. CAN communication line AT- 9 6
6. Control valve with TCMAT-230
OFF vehicle 7. Torque converter AT-264
No. ItemsSymptom Condition Diagnostic ItemReference
page

AT-82
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
65 OthersEngine speed does
not return to idle.
Refer to
AT-208,
"Engine Speed Does
Not Return to Idle" .ON vehicle 1. Fluid level and state
AT- 5 1
2. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 6 3,
AT- 1 4 7
3. ATF pressure switch 1 and front brake solenoid valve AT- 1 5 9,
AT- 1 4 3
4. Accelerator pedal position sensor AT- 1 2 4
5. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 111,
AT- 1 3 2
6. CAN communication line AT- 9 6
7. Control valve with TCMAT- 2 3 0
OFF vehicle8. Front brake (brake band)
AT- 2 6 49. Direct clutchAT- 2 9 8
No. ItemsSymptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSISAT-85
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
ATF PRES SW 1Front brake engaged. Refer to
AT- 2 0ON
Front brake disengaged. Refer to AT- 2 0
OFF
ATF PRES SW 2 Low coast brake engaged. Refer to
AT- 2 0
ON
Low coast brake disengaged. Refer to AT- 2 0
OFF
ATF PRES SW 3 Input clutch engaged. Refer to
AT- 2 0
ON
Input clutch disengaged. Refer to AT- 2 0
OFF
ATF PRES SW 5 Direct clutch engaged. Refer to
AT- 2 0
ON
Direct clutch disengaged. Refer to AT- 2 0
OFF
ATF PRES SW 6 High and low reverse clutch engaged. Refer to
AT- 2 0
ON
High and low reverse clutch disengaged. Refer to AT- 2 0
OFF
I/C SOLENOID Input clutch disengaged. Refer to
AT- 2 0
0.6 - 0.8 A
Input clutch engaged. Refer to AT- 2 0
0 - 0.05 A
FR/B SOLENOID Front brake engaged. Refer to
AT- 2 0
0.6 - 0.8 A
Front brake disengaged. Refer to AT- 2 0
0 - 0.05 A
D/C SOLENOID Direct clutch disengaged. Refer to
AT- 2 0
0.6 - 0.8 A
Direct clutch engaged. Refer to AT- 2 0
0 - 0.05 A
HLR/C SOL High and low reverse clutch disengaged. Refer to
AT- 2 0
0.6 - 0.8 A
High and low reverse clutch engaged. Refer to AT- 2 0
0 - 0.05 A
ON OFF SOL Low coast brake engaged. Refer to
AT- 2 0
ON
Low coast brake disengaged. Refer to AT- 2 0
OFF
STARTER RELAY Selector lever in
“N ”,“ P ” position. ON
Selector lever in other position. OFF
ACCELE POSI Released accelerator pedal.
0.0/8
Fully depressed accelerator pedal. 8/8
CLSD THL POS Released accelerator pedal.
ON
Fully depressed accelerator pedal. OFF
W/O THL POS Fully depressed accelerator pedal.
ON
Released accelerator pedal. OFF
BRAKE SW Depressed brake pedal.
ON
Released brake pedal. OFF
Item name
Condition Display value (Approx.)

AT-90
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
DATA MONITOR MODE
Operation Procedure
1. Perform “CONSULT-II SETTING PROCEDURE ”. Refer to AT- 8 6 , "CONSULT-II SETTING PROCEDURE"
.
2. Touch “DATA MONITOR ”.
NOTE:
When malfunction is detected, CONSULT-II performs
“REAL-TIME DIAGNOSIS”. Also, any malfunction detected
while in this mode will be displayed at real time.
Display Items List
X: Standard, —: Not applicable
BCIA0031E
Monitored item (Unit) Monitor Item Selection
Remarks
ECU
INPUT
SIGNALS MAIN SIG-
NALS SELEC-
TION
FROM
MENU
VHCL/S SE ·A/T (km/h) XXX Revolution sensor
VHCL/S SE ·MTR (km/h) X— X
ACCELE POSI (0.0/8) X— X Accelerator pedal position signal
THROTTLE POSI (0.0/8) XXXDegree of opening for accelerator recognized by
the TCM
For fail-safe operation, the specific value used
for control is displayed.
CLSD THL POS (ON-OFF display) X— X
Signal input with CAN communications
W/O THL POS (ON-OFF display) X— X
BRAKE SW (ON-OFF display) X— X Stop lamp switch
GEAR —XX Gear position recognized by the TCM updated
after gear-shifting
ENGINE SPEED (rpm) XXX
TURBINE REV (rpm) XXX
OUTPUT REV (rpm) XXX
GEAR RATIO —XX
TC SLIP SPEED (rpm) —XX Difference between engine speed and torque
converter input shaft speed
F SUN GR REV (rpm) ——X
F CARR GR REV (rpm) ——X
ATF TEMP SE 1 (V) X— X
ATF TEMP SE 2 (V) X— X
ATF TEMP 1 ( °C) —XX
ATF TEMP 2 ( °C) —XX
BATTERY VOLT (V) X— X
ATF PRES SW 1 (ON-OFF display) XXX (for FR/B solenoid)
ATF PRES SW 2 (ON-OFF display) XXX (for LC/B solenoid)
ATF PRES SW 3 (ON-OFF display) XXX (for I/C solenoid)
ATF PRES SW 5 (ON-OFF display) XXX (for D/C solenoid)

AT-134
DTC P1730 A/T INTERLOCK
Revision: November 20092006 QX56
DTC P1730 A/T INTERLOCKPFP:00000
DescriptionECS00CH5

Fail-safe function to detect interlock conditions.
On Board Diagnosis LogicECS00CH6

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “P1730 A/T INTERLOCK ” with CONSULT-II is detected when TCM does not
receive the proper voltage signal from the sensor and switch.

TCM monitors and compares gear position and conditions of each ATF pressure switch when gear is
steady.
Possible CauseECS00CH7

Harness or connectors
(The solenoid and switch circuit is open or shorted.)

Low coast brake solenoid valve

ATF pressure switch 2
DTC Confirmation ProcedureECS00CH8
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ ON”. (Do not start engine.)
2. Select “DATA MONITOR ” mode for “A/T” with CONSULT-II.
3. Start engine.
4. Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.
Selector lever: “D” position
5. If DTC is detected, go to AT- 1 3 5 , "
Diagnostic Procedure" .
WITH GST
Follow the procedure “With CONSULT-II”.
BCIA0030E

DTC P1730 A/T INTERLOCKAT-135
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
Judgement of A/T InterlockECS00CH9
When A/T Interlock is judged to be malfunctioning, the vehicle should be fixed in 2nd gear, and should be set
in a condition in which it can travel.
When one of the following fastening patterns is detected, the fail-safe function in correspondence with the indi-
vidual pattern should be performed.
A/T INTERLOCK COUPLING PATTERN TABLE

: NG, X: OK
Diagnostic ProcedureECS00CHA
1. SELF-DIAGNOSIS
With CONSULT-II
1. Drive vehicle.
2. Stop vehicle and turn ignition switch “OFF”.
3. Turn ignition switch “ON”.
4. Select “SELF-DIAG RESULTS” mode for “A/T ” with CONSULT-
II.
OK or NG
OK >> GO TO 2.
NG >> Check low coast brake solenoid valve circuit and func- tion. Refer to AT- 1 5 5 , "
DTC P1772 LOW COAST
BRAKE SOLENOID VALVE" , AT- 1 5 7 , "DTC P1774
LOW COAST BRAKE SOLENOID VALVE FUNCTION" .
2. CHECK DTC
Perform “DTC Confirmation Procedure ”.

Refer to AT- 1 3 4 , "DTC Confirmation Procedure" .
OK or NG
OK >> INSPECTION END
NG >> GO TO 3.
3. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT- 1 6 7 , "
MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 4.
NG >> Repair or replace damaged parts.
Gear position ATF pressure switch output
Fail-safe function Clutch pressure output pattern after fail-safe func-
tion
SW3 (I/C) SW6
(HLR/ C) SW5
(D/C) SW1
(FR/B) SW2
(LC/B) I/C HLR/C D/C FR/B LC/B L/U
A/T interlock
coupling pat-
tern 3rd
–XX –
Held in
2nd gear OFF OFF ON OFF OFF OFF
4th –XX –
Held in
2nd gear OFF OFF ON OFF OFF OFF
5th X X –X
Held in
2nd gear OFF OFF ON OFF OFF OFF
BCIA0031E

DTC P1731 A/T 1ST ENGINE BRAKINGAT-137
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
DTC P1731 A/T 1ST ENGINE BRAKINGPFP:00000
DescriptionECS00CHB
Fail-safe function to prevent sudden decrease in speed by engine brake other than at "1" position.
CONSULT-II Reference ValueECS00CHC
On Board Diagnosis LogicECS00CHD

This is not an OBD-II self-diagnostic item.

Diagnostic trouble code “P1731 A/T 1ST E/BRAKING ” with CONSULT-II is detected under the following
conditions.
–When TCM does not receive the proper voltage signal from the sensor.
–When TCM monitors each ATF pressure switch and solenoid monitor value, and detects as irregular when
engine brake of 1st gear acts other than at 1 position.
Possible CauseECS00CHE

Harness or connectors
(The sensor circuit is open or shorted.)

Low coast brake solenoid valve

ATF pressure switch 2
DTC Confirmation ProcedureECS00CHF
NOTE:
If “DTC Confirmation Procedure” has been previously preformed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR ” mode for “A/T” with CONSULT-II.
3. Start engine.
4. Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.
ENGINE SPEED: 1,200 rpm
Selector lever: “1” position
Gear position: 1st gear
5. If DTC is detected, go to AT- 1 3 8 , "
Diagnostic Procedure" .
Item name Condition Display value
ON OFF SOL Low coast brake engaged. Refer to
AT- 2 0
.O N
Low coast brake disengaged. Refer to AT- 2 0
.O FF
ATF PRES SW 2 Low coast brake engaged. Refer to
AT- 2 0
.O N
Low coast brake disengaged. Refer to AT- 2 0
.O FF
BCIA0030E

AT-138
DTC P1731 A/T 1ST ENGINE BRAKING
Revision: November 20092006 QX56
Diagnostic ProcedureECS00CHG
1. CHECK INPUT SIGNALS
With CONSULT-II
1. Start the engine.
2. Select “SELECTION FROM MENU” in “DATA MONITOR” for
"A/T" with CONSULT-II"
3. Drive vehicle in the “1 ” position (1st gear), and confirm the ON/
OFF actuation of “ATF PRES SW 2 ” and "ON OFF SOL".
OK or NG
OK >> GO TO 4.
NG >> GO TO 2.
2. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT- 1 6 7 , "
MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. DETECT MALFUNCTIONING ITEM
Check the following items:

The A/T assembly harness connector pin terminals for damage or loose connection with harness connec-
tor.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT- 2 3 0 , "Control Valve With TCM and A/T Fluid
Temperature Sensor 2" .
NG >> Repair or replace damaged parts.
4. CHECK DTC
Perform “DTC Confirmation Procedure ”.

Refer to AT- 1 3 7 , "DTC Confirmation Procedure" .
OK or NG
OK >> INSPECTION END
NG >> GO TO 2.
Item name Condition Display value
ON OFF
SOL Low coast brake engaged. Refer to
AT- 2 0
.ON
Low coast brake disengaged. Refer to AT- 2 0
.OFF
ATF PRES
SW 2 Low coast brake engaged. Refer to
AT- 2 0
.ON
Low coast brake disengaged. Refer to AT- 2 0
.OFF
PCIA0067E