JAGUAR XFR 2010 1.G Workshop Manual

Climate Control - Blower Motor Control Module
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).







Installation

2. CAUTION: Take extra care not to damage the clips or
screw threads. Failure to follow this instruction may result
in damage to the climate control assembly.


NOTE: RHD illustration shown, LHD is similar.


















3. Torque: 1.3 Nm
1. To install, reverse the removal procedure.

Climate Control - Center Registers
Removal and Installation

Removal Published: 11-May-2011

CAUTION: Do not manually open the registers. Failure to follow this instruction may result in damage to the internal
components.
NOTES:


The center registers must be open before carrying out this procedure. To achieve this set the registers to 'Always Open'
using the climate settings tab on the information and entertainment display. If the registers are set to 'Automatic' mode
(rotating with ignition on/off) and one or more are disconnected during an ignition cycle, a vehicle battery reset may be
required to reconnect the affected registers to the LIN BUS.

Removal steps in this procedure may contain installation details.

1. Set the registers to 'Always Open', using the information and
entertainment display.

2. Refer to: Passenger Side Register (412-01 Climate Control, Removal and Installation).

3. Fully extend and lower the steering column for access.

4. www.JagDocs.com

5.
6. CAUTIONS:


The center registers must be open to aid access and
prevent damage to surrounding trim.


Do not manually open the registers. Failure to follow
this instruction may result in damage to the internal
components.









7. NOTE: Do not disassemble further if the component is
removed for access only.

Installation

1. To install, reverse the removal procedure.

2. Return the registers to their original setting - 'Automatic' - using the
information and entertainment display.

Climate Control - Climate Control Assembly
Removal and Installation

Removal

NOTES:


Removal steps in this procedure may contain installation details.


RHD illustration shown, LHD is similar. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Instrument Panel Console (501-12 Instrument Panel and Console, Removal and Installation).

4.
5. Torque: 9 Nm

6. CAUTION: Be prepared to collect escaping coolant.

Torque: 9 Nm













7.




Installation

1. To install, reverse the removal procedure.

Climate Control - Climate Control Module
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Instrument Panel Console (501-12 Instrument Panel and Console, Removal and Installation).




Installation

3. CAUTIONS:


Take extra care not to damage the clips or screw
threads. Failure to follow this instruction may result in
damage to the climate control assembly.


Make sure that the component is correctly located on
the locating dowels.


NOTE: RHD illustration shown, LHD is similar.

Torque: 1.3 Nm
1. To install, reverse the removal procedure. www.JagDocs.com

Climate Control - Defrost Vent/Register Blend Door Actuator
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01, General Procedures).

2. Refer to: Instrument Panel Console (501-12, Removal and Installation).




Installation

3. CAUTIONS:


Take extra care not to damage the clips or screw
threads. Failure to follow this instruction may result in
damage to the climate control assembly.


Make sure that the component is correctly located on
the locating dowels.


NOTE: RHD illustration shown, LHD is similar.

Torque: 1.3 Nm
1. To install, reverse the removal procedure.

Climate Control - Driver Side Register
Removal and Installation

Removal Published: 11-May-2011

CAUTION: Do not manually open the registers. Failure to follow this instruction may result in damage to the internal
components.
NOTES:


If the registers are set to 'Automatic' mode and one or more are disconnected during an ignition cycle, a vehicle battery
reset may be required to reconnect the affected registers to the LIN BUS.


Removal steps in this procedure may contain installation details.


1.