Lines JEEP LIBERTY 2002 KJ / 1.G Owners Manual

WARNING: IF THE VEHICLE IS EQUIPPED WITH AIR
CONDITIONING, REVIEW THE WARNINGS AND
CAUTIONS IN THE FRONT OF THIS SECTION
BEFORE PERFORMING THE FOLLOWING OPERA-
TION. (Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING - WARNING) (Refer to 24 - HEATING &
AIR CONDITIONING/PLUMBING - CAUTION)
(1) Remove the HVAC housing. (Refer to 24 -
HEATING & AIR CONDITIONING/DISTRIBUTION/
HVAC HOUSING - REMOVAL).
(2) Remove the two heater core retaining screws (if
equipped). (Fig. 14).
(3) Gently push back on two of the heater core
retaining tabs and pull up on heater core to remove.
INSTALLATION
WARNING: IF THE VEHICLE IS EQUIPPED WITH AIR
CONDITIONING, REVIEW THE WARNINGS AND
CAUTIONS IN THE FRONT OF THIS SECTION
BEFORE PERFORMING THE FOLLOWING OPERA-
TION. (Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING - WARNING) (Refer to 24 - HEATING &AIR CONDITIONING/PLUMBING - CAUTION) (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMBING -
CAUTION - REFRIGERANT HOSES/LINES/TUBES
PRECAUTIONS)
(1) Install the heater core into the top of the
HVAC housing.
(2) Push on top of heater core until all for tabs are
locked into place.
(3) Install the two heater core retainer screws.
(4) Install the HVAC housing. (Refer to 24 - HEAT-
ING & AIR CONDITIONING/DISTRIBUTION/HVAC
HOUSING - INSTALLATION)
REFRIGERANT
DESCRIPTION
The refrigerant used in this air conditioning sys-
tem is a HydroFluoroCarbon (HFC), type R-134a.
Unlike R-12, which is a ChloroFluoroCarbon (CFC),
R-134a refrigerant does not contain ozone-depleting
chlorine. R-134a refrigerant is a non-toxic, non-flam-
mable, clear, and colorless liquefied gas.
Even though R-134a does not contain chlorine, it
must be reclaimed and recycled just like CFC-type
refrigerants. This is because R-134a is a greenhouse
gas and can contribute to global warming.
OPERATION
R-134a refrigerant is not compatible with R-12
refrigerant in an air conditioning system. Even a
small amount of R-12 added to an R-134a refrigerant
system will cause compressor failure, refrigerant oil
sludge or poor air conditioning system performance.
In addition, the PolyAlkylene Glycol (PAG) synthetic
refrigerant oils used in an R-134a refrigerant system
are not compatible with the mineral-based refriger-
ant oils used in an R-12 refrigerant system.
R-134a refrigerant system service ports, service
tool couplers and refrigerant dispensing bottles have
all been designed with unique fittings to ensure that
an R-134a system is not accidentally contaminated
with the wrong refrigerant (R-12). There are also
labels posted in the engine compartment of the vehi-
cle and on the compressor identifying to service tech-
nicians that the air conditioning system is equipped
with R-134a.
REFRIGERANT OIL
DESCRIPTION
The refrigerant oil used in R-134a refrigerant sys-
tems is a synthetic-based, PolyAlkylene Glycol (PAG),
wax-free lubricant. Mineral-based R-12 refrigerant
Fig. 14 HEATER CORE REMOVAL/INSTALLATION
1 - HEATER CORE
2- MOUNTING SCREW HOLE
3- INLET AND OUTLET TUBES
4- VACUUM HARNESS
5- ACTUATOR SCREWS (3)
6- ELECTRIC BLEND DOOR ACTUATOR
7- MOUNTING SCREW HOLE
8- HEATER CORE RETAINER TABS (4)
KJPLUMBING 24 - 53
HEATER CORE (Continued)

EVAPORATIVE EMISSIONS
TABLE OF CONTENTS
page page
EVAPORATIVE EMISSIONS
DESCRIPTION - EVAPORATION CONTROL
SYSTEM............................24
SPECIFICATIONS
TORQUE............................26
EVAP/PURGE SOLENOID
DESCRIPTION.........................27
OPERATION...........................27
REMOVAL.............................27
INSTALLATION.........................27
FUEL FILLER CAP
DESCRIPTION.........................27
OPERATION...........................27
LEAK DETECTION PUMP
DESCRIPTION.........................27
OPERATION...........................28
REMOVAL.............................28INSTALLATION.........................28
ORVR
DESCRIPTION.........................29
OPERATION...........................29
P C V VA LV E
DESCRIPTION.........................29
OPERATION...........................31
DIAGNOSIS AND TESTING - PCV VALVE.....31
REMOVAL.............................32
INSTALLATION.........................32
VACUUM LINES
DESCRIPTION.........................33
VAPOR CANISTER
DESCRIPTION.........................33
OPERATION...........................33
REMOVAL.............................33
INSTALLATION.........................33
EVAPORATIVE EMISSIONS
DESCRIPTION - EVAPORATION CONTROL
SYSTEM
The evaporation control system prevents the emis-
sion of fuel tank vapors into the atmosphere. When
fuel evaporates in the fuel tank, the vapors pass
through the control valve located in the top section of
the fuel pump module, through the fuel management
valve, and through vent hoses and tubes to a char-
coal filled evaporative canister. The canister tempo-
rarily holds the vapors. The Powertrain Control
Module (PCM) allows intake manifold vacuum to
draw vapors into the combustion chambers during
certain operating conditions.
Gas powered engines use a duty cycle purge sys-
tem. The PCM controls vapor flow by operating theduty cycle EVAP purge solenoid. Refer to Duty Cycle
EVAP Canister Purge Solenoid.
When equipped with certain emissions packages, a
Leak Detection Pump (LDP) will be used as part of
the evaporative system for OBD II requirements.
Also refer to Leak Detection Pump.
Vehicles powered with gasoline engines are also
equipped with ORVR (On-Board Refueling Vapor
Recovery). Refer to ORVR for additional information.
NOTE: The evaporative system uses specially man-
ufactured lines/hoses. If replacement becomes nec-
essary, only use fuel resistant, low permeation
hose.
Certain components can be found in (Fig. 1).
25 - 24 EVAPORATIVE EMISSIONSKJ

(4) Carefully install vapor/vacuum lines to LDP,
and install hose to LDP filter.The vapor/vacuum
lines and hoses must be firmly connected.
Check the vapor/vacuum lines at the LDP, LDP
filter and EVAP canister duty cycle purge sole-
noid for damage or leaks. If a leak is present, a
Diagnostic Trouble Code (DTC) may be set.
ORVR
DESCRIPTION
The ORVR (On-Board Refueling Vapor Recovery)
system consists of a unique fuel tank, flow manage-
ment valve, fluid control valve, one-way check valve
and vapor canister (Fig. 1).
OPERATION
The ORVR (On-Board Refueling Vapor Recovery)
system is used to remove excess fuel tank vapors.
This is done while the vehicle is being refueled. Cer-
tain ORVR components can be found in (Fig. 1).
Fuel flowing into the fuel filler tube (approx. 1º
I.D.) creates an aspiration effect drawing air into the
fuel fill tube. During refueling, the fuel tank is
vented to the EVAP canister to capture escaping
vapors. With air flowing into the filler tube, there are
no fuel vapors escaping to the atmosphere. Once the
refueling vapors are captured by the EVAP canister,the vehicle's computer controlled purge system draws
vapor out of the canister for the engine to burn. The
vapor flow is metered by the purge solenoid so that
there is no, or minimal impact on driveability or
tailpipe emissions.
As fuel starts to flow through the fuel fill tube, it
opens the normally closed check valve and enters the
fuel tank. Vapor or air is expelled from the tank
through the control valve and on to the vapor canis-
ter. Vapor is absorbed in the EVAP canister until
vapor flow in the lines stops. This stoppage occurs
following fuel shut-off, or by having the fuel level in
the tank rise high enough to close the control valve.
This control valve contains a float that rises to seal
the large diameter vent path to the EVAP canister.
At this point in the refueling process, fuel tank pres-
sure increases, the check valve closes (preventing liq-
uid fuel from spiting back at the operator), and fuel
then rises up the fuel filler tube to shut off the dis-
pensing nozzle.
PCV VALVE
DESCRIPTION
2.4L
The 2.4L 4-cylinder engine is equipped with a
closed crankcase ventilation system and a Positive
Crankcase Ventilation (PCV) valve.
This system consists of:
²a PCV valve attached to the left/front side of the
valve cover (Fig. 5). It is secured with 1 bolt. An
o-ring is used to seal valve to valve cover (Fig. 6).
²the air cleaner housing
²tubes and hoses to connect the system compo-
nents.
3.7L
The 3.7L V-6 engine is equipped with a closed
crankcase ventilation system and a Positive Crank-
case Ventilation (PCV) valve.
This system consists of:
²a PCV valve mounted to the oil filler housing
(Fig. 7). The PCV valve is sealed to the oil filler
housing with an o-ring.
²the air cleaner housing
²two interconnected breathers threaded into the
rear of each cylinder head (Fig. 8).
²tubes and hoses to connect the system compo-
nents.
Fig. 4 LDP ELECTRICAL CONNECTOR
1 - LEAK DETECTION PUMP (LDP)
2 - ELECTRICAL CONNECTOR
3 - FUEL FILTER
KJEVAPORATIVE EMISSIONS 25 - 29
LEAK DETECTION PUMP (Continued)

VACUUM LINES
DESCRIPTION
A vacuum schematic for emission related items can
be found on the VECI label. Refer to Vehicle Emis-
sion Control Information (VECI) Label for label loca-
tion.
VAPOR CANISTER
DESCRIPTION
A maintenance free, EVAP canister is used on all
gasoline powered models. The EVAP canister is
located near the left/front corner of the fuel tank.
OPERATION
The EVAP canister is filled with granules of an
activated carbon mixture. Fuel vapors entering the
EVAP canister are absorbed by the charcoal granules.
The canister serves two functions: as a temporary
fuel vapor storage point while refueling the vehicle
for the ORVR system, as a temporary vapor storage
point while the engine is running.
Fuel tank pressure vents into the EVAP canister.
Fuel vapors are temporarily held in the canister until
they can be drawn into the intake manifold. The duty
cycle EVAP canister purge solenoid allows the EVAP
canister to be purged at predetermined times and at
certain engine operating conditions.
Refer to ORVR for additional information.
REMOVAL
The EVAP canister is located near front of fuel
tank and next to left/rear spring. (Fig. 13).
(1) Raise vehicle.
(2) Disconnect vacuum hoses/lines at EVAP canis-
ter. Note location of lines before removal.
(3) Remove EVAP canister and mounting bracket
assembly from body (2 bolts).
(4) Remove canister-to-mounting bracket bolt.
(5) Slide 2 canister mounting pins from mounting
bracket (Fig. 14).
INSTALLATION
(1) Slide 2 canister mounting pins into mounting
bracket (Fig. 14).
(2) Install canister-to-mounting bracket bolt.
(3) Position canister and bracket assembly to body.
(4) Install 2 mounting bracket bolts. Tighten to 47
N´m (35 ft. lbs.) torque.
(5) Connect vacuum hoses/lines at EVAP canister.
(6) Lower vehicle.
Fig. 13 EVAP CANISTER LOCATION
1 - LEFT/REAR SPRING
2 - EVAP CANISTER
3 - MOUNTING BRACKET
4 - BRACKET BOLTS
5 - VACUUM LINES
Fig. 14 EVAP CANISTER MOUNTING PINS
1 - MOUNTING PINS
2 - MOUNTING BRACKET
3 - EVAP CANISTER
KJEVAPORATIVE EMISSIONS 25 - 33

BRAKE CALIPERS - OPERATION, DISC.....5-14
BRAKE CALIPERS - REMOVAL, DISC......5-14
BRAKE COMPONENTS, SPECIFICATIONS....5-6
BRAKE DRUM - DIAGNOSIS AND
TESTING............................5-27
BRAKE DRUM MACHINING - STANDARD
PROCEDURES........................5-27
BRAKE FLUID CONTAMINATION -
DIAGNOSIS AND TESTING..............5-26
BRAKE FLUID, SPECIFICATIONS..........5-27
BRAKE HOSE - INSTALLATION, FRONT.....5-10
BRAKE HOSE - INSTALLATION, REAR......5-10
BRAKE HOSE - REMOVAL, REAR..........5-9
BRAKE INDICATOR - DESCRIPTION,
BRAKE/PARK........................8J-13
BRAKE INDICATOR - DIAGNOSIS AND
TESTING...........................8J-14
BRAKE INDICATOR - OPERATION,
BRAKE/PARK........................8J-13
BRAKE LAMP SWITCH - DESCRIPTION . . . 8L-16
BRAKE LAMP SWITCH - DIAGNOSIS
AND TESTING.......................8L-17
BRAKE LAMP SWITCH - INSTALLATION . . . 8L-18
BRAKE LAMP SWITCH - OPERATION.....8L-16
BRAKE LAMP SWITCH - REMOVAL......8L-17
BRAKE LINE AND HOSES - DIAGNOSIS
AND TESTING.........................5-8
BRAKE LINES - DESCRIPTION............5-8
BRAKE PADS - INSTALLATION, FRONT.....5-11
BRAKE PADS - REMOVAL, FRONT........5-11
BRAKE ROTOR - DIAGNOSIS AND
TESTING, DISC.......................5-18
BRAKE ROTOR - STANDARD
PROCEDURE, DISC....................5-19
BRAKE SHOES - INSTALLATION, DRUM....5-11
BRAKE SHOES - REMOVAL, DRUM.......5-11
BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE........................5-3
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - DESCRIPTION....21-124
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - DIAGNOSIS
AND TESTING......................21-125
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - OPERATION.....21-125
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION.......................8J-13
BRAKE/PARK BRAKE INDICATOR -
OPERATION.........................8J-13
BRAKES - ABS - DESCRIPTION...........5-32
BRAKES - ABS - OPERATION............5-32
BRAKES - ABS - SPECIFICATIONS........5-33
BRAKES - BASE - DESCRIPTION...........5-2
BRAKES - BASE - WARNING..............5-2
BRAKES, SPECIAL TOOLS - BASE.........5-7
BRAKING SYSTEM - DIAGNOSIS AND
TESTING, ANTILOCK...................5-33
BREAK-IN - STANDARD PROCEDURE,
A/C COMPRESSOR CLUTCH............24-12
BUCKLE - INSTALLATION, FRONT SEAT
BELT ..............................8O-26
BUCKLE - INSTALLATION, REAR SEAT
BELT ..............................8O-35
BUCKLE - REMOVAL, FRONT SEAT BELT . . 8O-25
BUCKLE - REMOVAL, REAR SEAT BELT . . . 8O-34
BUILT-IN INDICATOR TEST - STANDARD
PROCEDURE........................8F-10
BULB - INSTALLATION, ASH RECEIVER
LAMP..............................8L-71
BULB - INSTALLATION, CARGO LAMP....8L-73
BULB - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP................8L-19
BULB - INSTALLATION, COMPASS
MINI-TRIP ILLUMINATION..............8L-75
BULB - INSTALLATION, COURTESY
LAMP..............................8L-76
BULB - INSTALLATION, FRONT FOG
LAMP..............................8L-22
BULB - INSTALLATION, FRONT LAMP....8L-27
BULB - INSTALLATION, FRONT POSITION
LAMP..............................8L-28
BULB - INSTALLATION, HEADLAMP
......8L-32
BULB - INSTALLATION, HEATER-A/C
CONTROL ILLUMINATION
..............8L-78
BULB - INSTALLATION, LICENSE PLATE
LAMP
..............................8L-45
BULB - INSTALLATION, READING LAMP
. . . 8L-79
BULB - INSTALLATION, REAR LAMP
.....8L-59BULB - INSTALLATION, REPEATER LAMP . . 8L-60
BULB - INSTALLATION, TRANSMISSION
RANGE INDICATOR ILLUMINATION.......8L-83
BULB - INSTALLATION, VANITY LAMP....8L-84
BULB - REMOVAL, ASH RECEIVER LAMP . . 8L-71
BULB - REMOVAL, CARGO LAMP........8L-72
BULB - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP................8L-18
BULB - REMOVAL, COMPASS MINI-TRIP
ILLUMINATION......................8L-74
BULB - REMOVAL, COURTESY LAMP.....8L-75
BULB - REMOVAL, FRONT FOG LAMP....8L-21
BULB - REMOVAL, FRONT LAMP........8L-26
BULB - REMOVAL, FRONT POSITION
LAMP..............................8L-28
BULB - REMOVAL, HEADLAMP..........8L-31
BULB - REMOVAL, HEATER-A/C
CONTROL ILLUMINATION..............8L-78
BULB - REMOVAL, LICENSE PLATE
LAMP..............................8L-44
BULB - REMOVAL, READING LAMP......8L-79
BULB - REMOVAL, REAR LAMP.........8L-58
BULB - REMOVAL, REPEATER LAMP.....8L-60
BULB - REMOVAL, TRANSMISSION
RANGE INDICATOR ILLUMINATION.......8L-82
BULB - REMOVAL, VANITY LAMP........8L-83
BUMPER - INSTALLATION, JOUNCE.......2-19
BUMPER - REMOVAL, JOUNCE...........2-19
BURNT FLUID - DIAGNOSIS AND
TESTING, CAUSES OF................21-125
BUSHING - NV3550 - INSTALLATION,
EXTENSION HOUSING.................21-74
BUSHING - NV3550 - REMOVAL,
EXTENSION HOUSING.................21-73
BUSHINGS - INSTALLATION, STABILIZER
BAR.................................2-9
BUSHINGS - REMOVAL, STABILIZER BAR . . . 2-9
BUSHINGS, AND BALL JOINT -
DESCRIPTION, UPPER SUSPENSION
ARM ...............................2-20
BUSHINGS, AND BALL JOINT -
OPERATION, UPPER SUSPENSION
ARM ...............................2-20
CABLE - ADJUSTMENTS, GEARSHIFT....21-130
CABLE - ADJUSTMENTS, PARK-
INTERLOCK........................21-154
CABLE - DESCRIPTION.................8P-3
CABLE - DESCRIPTION, ANTENNA BODY . . . 8A-4
CABLE - DIAGNOSIS AND TESTING,
ANTENNA BODY......................8A-5
CABLE - DIAGNOSIS AND TESTING,
GEARSHIFT........................21-128
CABLE - INSTALLATION, ANTENNA BODY . . 8A-6
CABLE - INSTALLATION, GEARSHIFT....21-129
CABLE - INSTALLATION, INSTRUMENT
PANEL ANTENNA......................8A-8
CABLE - INSTALLATION, LATCH RELEASE . 23-120
CABLE - INSTALLATION, PARK -
INTERLOCK........................21-153
CABLE - INSTALLATION, THROTTLE
CONTROL..........................14-46
CABLE - OPERATION...................8P-3
CABLE - OPERATION, ANTENNA BODY.....8A-5
CABLE - REMOVAL, ANTENNA BODY......8A-6
CABLE - REMOVAL, GEARSHIFT........21-128
CABLE - REMOVAL, INSTRUMENT PANEL
ANTENNA...........................8A-7
CABLE - REMOVAL, LATCH RELEASE....23-120
CABLE - REMOVAL, PARK - INTERLOCK . 21-153
CABLE - REMOVAL, THROTTLE
CONTROL..........................14-45
CABLE RESISTANCE, 2.4L - SPARK PLUG . . . 8I-3
CABLES - DESCRIPTION, BATTERY.......8F-18
CABLES - DIAGNOSIS AND TESTING,
BATTERY...........................8F-19
CABLES - INSTALLATION...............5-30
CABLES - OPERATION, BATTERY........8F-18
CABLES - REMOVAL...................5-30
CALIBRATION - STANDARD PROCEDURE,
COMPASS...........................8M-2
CALIPER ADAPTER - INSTALLATION,
DISC BRAKE.........................5-18
CALIPER ADAPTER - REMOVAL, DISC
BRAKE
..............................5-18
CALIPERS - ASSEMBLY, DISC BRAKE
......5-16
CALIPERS - CLEANING, DISC BRAKE
......5-16
CALIPERS - DESCRIPTION, DISC BRAKE
. . . 5-13
CALIPERS - DISASSEMBLY, DISC BRAKE
. . . 5-14CALIPERS - INSPECTION, DISC BRAKE....5-16
CALIPERS - INSTALLATION, DISC BRAKE . . . 5-17
CALIPERS - OPERATION, DISC BRAKE.....5-14
CALIPERS - REMOVAL, DISC BRAKE......5-14
CAMBER AND CASTER ADJUSTMENT -
STANDARD PROCEDURE.................2-5
CAMBER, CASTER AND TOE
ADJUSTMENT - STANDARD
PROCEDURE..........................2-5
CAMSHAFT(S) - DESCRIPTION.......9-23,9-33
CAMSHAFT(S) - INSTALLATION......9-25,9-33
CAMSHAFT(S) - REMOVAL..........9-24,9-33
CANISTER - DESCRIPTION, VAPOR......25-33
CANISTER - INSTALLATION, VAPOR......25-33
CANISTER - OPERATION, VAPOR........25-33
CANISTER - REMOVAL, VAPOR..........25-33
CAP - CLEANING, RADIATOR PRESSURE . . . 7-25
CAP - DESCRIPTION, FUEL FILLER.......25-27
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-25
CAP - DIAGNOSIS AND TESTING,
RADIATOR PRESSURE.................7-25
CAP - INSPECTION, RADIATOR
PRESSURE..........................7-25
CAP - INSTALLATION, INSTRUMENT
PANEL END........................23-153
CAP - OPERATION, FUEL FILLER........25-27
CAP - OPERATION, RADIATOR
PRESSURE..........................7-25
CAP - REMOVAL, INSTRUMENT PANEL
END ..............................23-153
CAPACITIES - SPECIFICATIONS, FLUID......0-4
CAPACITOR - DESCRIPTION, IGNITION
COIL...............................8I-16
CAPACITOR - INSTALLATION, IGNITION
COIL...............................8I-16
CAPACITOR - OPERATION, IGNITION
COIL...............................8I-16
CAPACITOR - REMOVAL, IGNITION COIL . . . 8I-16
CAPACITY - SPECIFICATIONS, CHARGE . . . 24-42
CAPACITY TEST - DIAGNOSIS AND
TESTING, FUEL PUMP.................14-15
CARDAN UNIVERSAL JOINTS -
ASSEMBLY, SINGLE.....................3-9
CARDAN UNIVERSAL JOINTS -
DISASSEMBLY, SINGLE..................3-8
CARGO LAMP BULB - INSTALLATION.....8L-73
CARGO LAMP BULB - REMOVAL........8L-72
CARGO LAMP SWITCH - INSTALLATION . . 8L-74
CARGO LAMP SWITCH - REMOVAL......8L-73
CARGO LAMP UNIT - INSTALLATION.....8L-74
CARGO LAMP UNIT - REMOVAL.........8L-74
CARPETS AND FLOOR MATS -
INSTALLATION......................23-158
CARPETS AND FLOOR MATS - REMOVAL . 23-158
CASE - NV231 - ASSEMBLY, TRANSFER . . 21-194
CASE - NV231 - CLEANING, TRANSFER . . 21-190
CASE - NV231 - DESCRIPTION,
TRANSFER............................0-3
CASE - NV231 - DESCRIPTION,
TRANSFER.........................21-178
CASE - NV231 - DIAGNOSIS AND
TESTING, TRANSFER.................21-180
CASE - NV231 - DISASSEMBLY,
TRANSFER.........................21-182
CASE - NV231 - INSPECTION, TRANSFER . 21-190
CASE - NV231 - INSTALLATION,
TRANSFER.........................21-205
CASE - NV231 - OPERATION, TRANSFER
. 21-179
CASE - NV231 - REMOVAL, TRANSFER
. . 21-181
CASE - NV242 - ASSEMBLY, TRANSFER
. . 21-230
CASE - NV242 - CLEANING, TRANSFER
. . 21-227
CASE - NV242 - DESCRIPTION,
TRANSFER
............................0-3
CASE - NV242 - DESCRIPTION,
TRANSFER
.........................21-215
CASE - NV242 - DIAGNOSIS AND
TESTING, TRANSFER
.................21-216
CASE - NV242 - DISASSEMBLY,
TRANSFER
.........................21-218
CASE - NV242 - INSPECTION, TRANSFER
. 21-228
CASE - NV242 - INSTALLATION,
TRANSFER
.........................21-243
CASE - NV242 - OPERATION, TRANSFER
. 21-215
CASE - NV242 - REMOVAL, TRANSFER
. . 21-217
CASE BEARINGS - INSTALLATION,
DIFFERENTIAL
...............3-110,3-44,3-79
4 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

CASE BEARINGS - REMOVAL,
DIFFERENTIAL...............3-110,3-43,3-79
CASE, NV231 - TRANSFER............21-206
CASE, NV242 - TRANSFER............21-244
CASE SKID PLATE - INSTALLATION,
TRANSFER...........................13-7
CASE SKID PLATE - REMOVAL,
TRANSFER...........................13-7
CASE, SPECIFICATIONS - NV242
TRANSFER.........................21-244
CASTER ADJUSTMENT - STANDARD
PROCEDURE, CAMBER..................2-5
CASTER AND TOE ADJUSTMENT -
STANDARD PROCEDURE, CAMBER........2-5
CATALYTIC CONVERTER - DESCRIPTION . . . 11-2
CATALYTIC CONVERTER - INSPECTION....11-3
CATALYTIC CONVERTER - INSTALLATION . . . 11-3
CATALYTIC CONVERTER - REMOVAL......11-2
CAUSES OF BURNT FLUID - DIAGNOSIS
AND TESTING......................21-125
CAUTION - SERVICE CAUTIONS.........24-39
CAUTION, HALF SHAFT.................3-10
CAUTION, REFRIGERANT HOSES/LINES/
TUBES PRECAUTIONS.................24-40
CAUTIONS, CAUTION - SERVICE.........24-39
CD CHANGER - DESCRIPTION...........8A-7
CD CHANGER - INSTALLATION...........8A-7
CD CHANGER - OPERATION.............8A-7
CD CHANGER - REMOVAL..............8A-7
CENTER - DESCRIPTION, POWER
DISTRIBUTION....................8W-97-6
CENTER - OPERATION, POWER
DISTRIBUTION....................8W-97-7
CENTER - REMOVAL, POWER
DISTRIBUTION....................8W-97-7
CENTER ASSEMBLY, ASSEMBLY -
POWER DISTRIBUTION.............8W-97-10
CENTER BEZEL - INSTALLATION,
INSTRUMENT PANEL.................23-154
CENTER BEZEL - REMOVAL,
INSTRUMENT PANEL.................23-154
CENTER DISASSEMBLY, DISASSEMBLY -
POWER DISTRIBUTION..............8W-97-7
CENTER HIGH MOUNTED STOP LAMP
BULB - INSTALLATION................8L-19
CENTER HIGH MOUNTED STOP LAMP
BULB - REMOVAL....................8L-18
CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION.................8L-19
CENTER HIGH MOUNTED STOP LAMP
UNIT - REMOVAL....................8L-19
CENTER SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-33
CENTER SEAT BELT & RETRACTOR -
REMOVAL, REAR....................8O-32
CENTERING - STANDARD PROCEDURE,
CLOCKSPRING......................8O-14
CERTIFICATION LABEL - DESCRIPTION,
VEHICLE SAFETY...................Intro.-9
CHAIN COVER(S) - INSTALLATION,
TIMING BELT.........................9-76
CHAIN COVER(S) - REMOVAL, TIMING
BELT ...............................9-74
CHAIN WEAR, STANDARD PROCEDURE -
MEASURING TIMING...................9-71
CHANGER - DESCRIPTION, CD...........8A-7
CHANGER - INSTALLATION, CD..........8A-7
CHANGER - OPERATION, CD.............8A-7
CHANGER - REMOVAL, CD..............8A-7
CHANNEL - INSTALLATION, GLASS RUN . 23-123,
23-130
CHANNEL - REMOVAL, GLASS RUN....23-123,
23-130
CHARGE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-41
CHARGE CAPACITY - SPECIFICATIONS....24-42
CHARGING - STANDARD PROCEDURE,
BATTERY............................8F-8
CHARGING INDICATOR - DESCRIPTION . . . 8J-15
CHARGING INDICATOR - OPERATION.....8J-15
CHARGING SYSTEM - DESCRIPTION
.....8F-22
CHARGING SYSTEM - DIAGNOSIS AND
TESTING
...........................8F-22
CHARGING SYSTEM - OPERATION
.......8F-22
CHART - DIAGNOSIS AND TESTING,
COOLING SYSTEM DIAGNOSIS
............7-6
CHART, SPECIFICATIONS - TORQUE
.....19-15,
19-19,19-8CHART, SPECIFICATIONS - TORQUE....2-17,2-8
CHECK - STANDARD PROCEDURE, FLUID
LEVEL............................21-126
CHECK - STANDARD PROCEDURE, OIL
PUMP VOLUME.....................21-148
CHECK STRAP - INSTALLATION . . 23-121,23-128,
23-135
CHECK STRAP - REMOVAL.....23-121,23-128,
23-135
CHECK VALVE - DESCRIPTION, FRONT....8R-8
CHECK VALVE - DESCRIPTION, FUEL
TANK ..............................14-28
CHECK VALVE - DESCRIPTION, REAR....8R-34
CHECK VALVE - DESCRIPTION, VACUUM . . 24-28
CHECK VALVE - INSTALLATION, FRONT....8R-9
CHECK VALVE - INSTALLATION, FUEL
TANK ..............................14-28
CHECK VALVE - INSTALLATION, REAR....8R-35
CHECK VALVE - INSTALLATION, VACUUM . 24-28
CHECK VALVE - OPERATION, FRONT......8R-9
CHECK VALVE - OPERATION, FUEL TANK . . 14-28
CHECK VALVE - OPERATION, REAR......8R-34
CHECK VALVE - OPERATION, VACUUM....24-28
CHECK VALVE - REMOVAL, FRONT.......8R-9
CHECK VALVE - REMOVAL, FUEL TANK . . . 14-28
CHECK VALVE - REMOVAL, REAR.......8R-34
CHECK VALVE - REMOVAL, VACUUM.....24-28
CHECKING TRANSMISSION CLUTCH
OPERATION - DIAGNOSIS AND
TESTING, AIR.......................21-80
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY.........................7-3
CHILD TETHER ANCHOR - DESCRIPTION . . 8O-13
CHILD TETHER ANCHOR - OPERATION . . . 8O-13
CHIME WARNING SYSTEM -
DESCRIPTION........................8B-1
CHIME WARNING SYSTEM - DIAGNOSIS
AND TESTING........................8B-6
CHIME WARNING SYSTEM - OPERATION . . . 8B-2
CHOKE AND RELAY - DESCRIPTION,
AMPLIFIER..........................8A-3
CHOKE AND RELAY - DIAGNOSIS AND
TESTING, AMPLIFIER..................8A-4
CHOKE AND RELAY - INSTALLATION,
AMPLIFIER..........................8A-4
CHOKE AND RELAY - OPERATION,
AMPLIFIER..........................8A-3
CHOKE AND RELAY - REMOVAL,
AMPLIFIER..........................8A-4
CIGAR LIGHTER OUTLET -
DESCRIPTION.....................8W-97-2
CIGAR LIGHTER OUTLET - DIAGNOSIS
AND TESTING.....................8W-97-2
CIGAR LIGHTER OUTLET - OPERATION . 8W-97-2
CLEVIS BRACKET - INSTALLATION........2-13
CLEVIS BRACKET - REMOVAL...........2-13
CLOCKSPRING - DESCRIPTION.........8O-13
CLOCKSPRING - INSTALLATION.........8O-16
CLOCKSPRING - OPERATION...........8O-14
CLOCKSPRING - REMOVAL............8O-15
CLOCKSPRING CENTERING - STANDARD
PROCEDURE........................8O-14
CLUSTER - ASSEMBLY, INSTRUMENT....8J-10
CLUSTER - DESCRIPTION, INSTRUMENT . . . 8J-2
CLUSTER - DIAGNOSIS AND TESTING,
INSTRUMENT........................8J-7
CLUSTER - DISASSEMBLY, INSTRUMENT . . . 8J-9
CLUSTER - INSTALLATION, INSTRUMENT . 8J-11
CLUSTER - OPERATION, INSTRUMENT.....8J-4
CLUSTER - REMOVAL, INSTRUMENT......8J-9
CLUSTER BEZEL - INSTALLATION.......23-147
CLUSTER BEZEL - REMOVAL..........23-147
CLUTCH - ASSEMBLY, LOW/REVERSE
. . . 21-146
CLUTCH - CLEANING, LOW/REVERSE
....21-146
CLUTCH - DESCRIPTION
.................6-1
CLUTCH - DIAGNOSIS AND TESTING
.......6-2
CLUTCH - DISASSEMBLY, LOW/REVERSE
. 21-145
CLUTCH - INSPECTION, A/C
COMPRESSOR
.......................24-14
CLUTCH - INSPECTION, LOW/REVERSE
. . 21-146
CLUTCH - INSTALLATION, A/C
COMPRESSOR
.......................24-14
CLUTCH - OPERATION
..................6-1
CLUTCH - REMOVAL, A/C COMPRESSOR
. . 24-13
CLUTCH - SPECIFICATIONS
...............6-5
CLUTCH - WARNING
....................6-2
CLUTCH ASSEMBLY - ASSEMBLY, INPUT
. 21-138CLUTCH ASSEMBLY - DESCRIPTION,
INPUT............................21-133
CLUTCH ASSEMBLY - DISASSEMBLY,
INPUT............................21-135
CLUTCH ASSEMBLY - OPERATION,
INPUT............................21-135
CLUTCH BREAK-IN - STANDARD
PROCEDURE, A/C COMPRESSOR........24-12
CLUTCH COIL - DIAGNOSIS AND
TESTING, A/C COMPRESSOR...........24-12
CLUTCH DISC - INSTALLATION............6-6
CLUTCH DISC - REMOVAL...............6-6
CLUTCH OPERATION - DIAGNOSIS AND
TESTING, AIR CHECKING
TRANSMISSION......................21-80
CLUTCH PEDAL - INSTALLATION.........6-10
CLUTCH PEDAL - REMOVAL.............6-10
CLUTCH PEDAL POSITION SWITCH -
DESCRIPTION........................6-11
CLUTCH PEDAL POSITION SWITCH -
DIAGNOSIS AND TESTING..............6-11
CLUTCH PEDAL POSITION SWITCH -
OPERATION..........................6-11
CLUTCH RELAY - DESCRIPTION, A/C
COMPRESSOR.......................24-15
CLUTCH RELAY - DIAGNOSIS AND
TESTING, COMPRESSOR...............24-15
CLUTCH RELAY - INSTALLATION, A/C
COMPRESSOR.......................24-16
CLUTCH RELAY - OPERATION, A/C
COMPRESSOR.......................24-15
CLUTCH RELAY - REMOVAL, A/C
COMPRESSOR........................24-16
CLUTCH RELEASE BEARING -
INSTALLATION.........................6-6
CLUTCH RELEASE BEARING - REMOVAL....6-6
CLUTCH SWITCH OVERRIDE RELAY -
DESCRIPTION........................6-10
CLUTCH SWITCH OVERRIDE RELAY -
INSTALLATION........................6-10
CLUTCH SWITCH OVERRIDE RELAY -
OPERATION..........................6-10
CLUTCH SWITCH OVERRIDE RELAY -
REMOVAL...........................6-10
CLUTCHES - DESCRIPTION, HOLDING . . . 21-131
CLUTCHES - OPERATION, HOLDING.....21-132
CMTC LAMP REPLACEMENT -
STANDARD PROCEDURE...............8M-2
COAT FINISH - DESCRIPTION, BASE
COAT/CLEAR.......................23-162
COAT/CLEAR COAT FINISH -
DESCRIPTION, BASE.................23-162
CODE - DESCRIPTION, PAINT..........23-162
CODES - DESCRIPTION, DIAGNOSTIC
TROUBLE............................25-2
CODES - SPECIFICATIONS, PAINT.......23-162
CODES - STANDARD PROCEDURE,
ERASING TRANSMITTER...............8M-8
CODES - STANDARD PROCEDURE,
SETTING TRANSMITTER...............8M-9
COIL - DESCRIPTION, IGNITION..........8I-9
COIL - DIAGNOSIS AND TESTING, A/C
COMPRESSOR CLUTCH...............24-12
COIL - INSTALLATION, IGNITION.........8I-10
COIL - OPERATION, IGNITION............8I-9
COIL - REMOVAL, IGNITION............8I-10
COIL CAPACITOR - DESCRIPTION,
IGNITION...........................8I-16
COIL CAPACITOR - INSTALLATION,
IGNITION...........................8I-16
COIL CAPACITOR - OPERATION,
IGNITION...........................8I-16
COIL CAPACITOR - REMOVAL, IGNITION . . . 8I-16
COIL RESISTANCE, 2.4L - IGNITION
.......8I-2
COIL RESISTANCE, 3.7L V-6 - IGNITION
....8I-3
COLLAPSIBLE SPACER - INSTALLATION
....3-70
COLLAPSIBLE SPACER - REMOVAL
.......3-70
COLUMN - DESCRIPTION
...............19-5
COLUMN - INSTALLATION
...............19-7
COLUMN - REMOVAL
..................19-5
COLUMN, SPECIAL TOOLS - STEERING
....19-8
COMBINATION FLASHER - DESCRIPTION
. . 8L-19
COMBINATION FLASHER - OPERATION
. . . 8L-19
COMBUSTION PRESSURE LEAKAGE -
DIAGNOSIS AND TESTING, CYLINDER
......9-8
COMMUNICATION - DESCRIPTION
........8E-8
COMMUNICATION - OPERATION
..........8E-8
KJINDEX 5
Description Group-Page Description Group-Page Description Group-Page

FLUID DRAIN AND FILL - STANDARD
PROCEDURE.................21-208,21-246
FLUID FILL/CHECK LOCATIONS -
DESCRIPTION.........................0-4
FLUID INDICATOR - DESCRIPTION,
WASHER...........................8J-35
FLUID INDICATOR - DIAGNOSIS AND
TESTING, WASHER...................8J-36
FLUID INDICATOR - OPERATION,
WASHER...........................8J-36
FLUID LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING................21-80
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT......21-125
FLUID LEVEL - STANDARD
PROCEDURES, MASTER CYLINDER.......5-26
FLUID LEVEL CHECK - STANDARD
PROCEDURE.......................21-126
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER...........................8R-17
FLUID LEVEL SWITCH - INSTALLATION,
WASHER...........................8R-18
FLUID LEVEL SWITCH - OPERATION,
WASHER...........................8R-17
FLUID LEVEL SWITCH - REMOVAL,
WASHER...........................8R-17
FLUID RESERVOIR - INSTALLATION.......5-26
FLUID RESERVOIR - REMOVAL..........5-26
FLUID, SPECIFICATIONS - BRAKE.........5-27
FLUID TYPES - DESCRIPTION.............0-1
FLUSH - SPECIFICATIONS, GAP........23-116
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM - REVERSE...........7-12
FLYWHEEL - DESCRIPTION...............6-7
FLYWHEEL - DIAGNOSIS AND TESTING.....6-8
FLYWHEEL - OPERATION................6-7
FOG LAMP BULB - INSTALLATION,
FRONT.............................8L-22
FOG LAMP BULB - REMOVAL, FRONT....8L-21
FOG LAMP INDICATOR - DESCRIPTION,
FRONT.............................8J-19
FOG LAMP INDICATOR - DESCRIPTION,
REAR..............................8J-27
FOG LAMP INDICATOR - OPERATION,
FRONT.............................8J-19
FOG LAMP INDICATOR - OPERATION,
REAR..............................8J-27
FOG LAMP RELAY - DESCRIPTION,
FRONT.............................8L-22
FOG LAMP RELAY - DESCRIPTION, REAR . 8L-56
FOG LAMP RELAY - DIAGNOSIS AND
TESTING, FRONT.....................8L-23
FOG LAMP RELAY - DIAGNOSIS AND
TESTING, REAR......................8L-57
FOG LAMP RELAY - INSTALLATION,
FRONT.............................8L-24
FOG LAMP RELAY - INSTALLATION,
REAR..............................8L-58
FOG LAMP RELAY - OPERATION, FRONT . . 8L-22
FOG LAMP RELAY - OPERATION, REAR . . . 8L-57
FOG LAMP RELAY - REMOVAL, FRONT . . . 8L-24
FOG LAMP RELAY - REMOVAL, REAR....8L-58
FOG LAMP UNIT - ADJUSTMENT, FRONT . . 8L-25
FOG LAMP UNIT - INSTALLATION,
FRONT.............................8L-25
FOG LAMP UNIT - REMOVAL, FRONT.....8L-25
FOLDING REAR SEAT BACK LATCH /
LOCK - INSTALLATION
...............23-170
FOLDING REAR SEAT BACK LATCH /
LOCK - REMOVAL
...................23-170
FOUR LOW MODE INDICATOR -
DESCRIPTION
.......................8J-29
FOUR LOW MODE INDICATOR -
OPERATION
.........................8J-30
FRAME - REAR - INSTALLATION, SEAT
BACK
.............................23-171
FRAME - REAR - REMOVAL, SEAT BACK
. 23-171
FRAME DIMENSIONS - SPECIFICATIONS
. . . 13-3
FRONT - DESCRIPTION
..................2-7
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL
............................9-47
FRONT - INSTALLATION, PROPELLER
SHAFT
...............................3-6
FRONT - INSTALLATION, SEAT
.........23-165
FRONT - INSTALLATION, SEAT BACK
....23-166
FRONT - INSTALLATION, SEAT BACK
COVER
............................23-167FRONT - INSTALLATION, SEAT BACK
CUSHION..........................23-167
FRONT - INSTALLATION, SEAT BACK
RECLINER.........................23-166
FRONT - INSTALLATION, SEAT CUSHION . 23-167
FRONT - INSTALLATION, SEAT CUSHION
COVER............................23-167
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-46
FRONT - REMOVAL, PROPELLER SHAFT....3-6
FRONT - REMOVAL, SEAT.............23-165
FRONT - REMOVAL, SEAT BACK........23-166
FRONT - REMOVAL, SEAT BACK COVER . . 23-166
FRONT - REMOVAL, SEAT BACK
CUSHION..........................23-167
FRONT - REMOVAL, SEAT BACK
RECLINER.........................23-166
FRONT - REMOVAL, SEAT CUSHION.....23-167
FRONT - REMOVAL, SEAT CUSHION
COVER............................23-167
FRONT - WARNING.....................2-7
FRONT AXLE - 186FIA - ADJUSTMENTS....3-25
FRONT AXLE - 186FIA - DESCRIPTION.....3-19
FRONT AXLE - 186FIA - INSTALLATION....3-24
FRONT AXLE - 186FIA - OPERATION......3-19
FRONT AXLE - 186FIA - REMOVAL........3-24
FRONT AXLE - SPECIFICATIONS..........3-33
FRONT AXLE, SPECIAL TOOLS...........3-34
FRONT BRAKE HOSE - INSTALLATION.......5-10
FRONT BRAKE PADS - INSTALLATION.....5-11
FRONT BRAKE PADS - REMOVAL.........5-11
FRONT CHECK VALVE - DESCRIPTION.....8R-8
FRONT CHECK VALVE - INSTALLATION....8R-9
FRONT CHECK VALVE - OPERATION.......8R-9
FRONT CHECK VALVE - REMOVAL........8R-9
FRONT DOOR OUTER BELT MOLDING -
INSTALLATION......................23-186
FRONT DOOR OUTER BELT MOLDING -
REMOVAL.........................23-186
FRONT FASCIA - INSTALLATION..........13-2
FRONT FASCIA - REMOVAL..............13-1
FRONT FENDER - INSTALLATION.......23-141
FRONT FENDER - REMOVAL...........23-141
FRONT FOG LAMP BULB -
INSTALLATION.......................8L-22
FRONT FOG LAMP BULB - REMOVAL.....8L-21
FRONT FOG LAMP INDICATOR -
DESCRIPTION.......................8J-19
FRONT FOG LAMP INDICATOR -
OPERATION.........................8J-19
FRONT FOG LAMP RELAY -
DESCRIPTION.......................8L-22
FRONT FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-23
FRONT FOG LAMP RELAY -
INSTALLATION.......................8L-24
FRONT FOG LAMP RELAY - OPERATION . . 8L-22
FRONT FOG LAMP RELAY - REMOVAL....8L-24
FRONT FOG LAMP UNIT - ADJUSTMENT . . 8L-25
FRONT FOG LAMP UNIT - INSTALLATION . . 8L-25
FRONT FOG LAMP UNIT - REMOVAL.....8L-25
FRONT HOSE - REMOVAL................5-9
FRONT IMPACT SENSOR - DESCRIPTION . 8O-21
FRONT IMPACT SENSOR -
INSTALLATION......................8O-22
FRONT IMPACT SENSOR - OPERATION . . . 8O-21
FRONT IMPACT SENSOR - REMOVAL....8O-22
FRONT LAMP BULB - INSTALLATION.....8L-27
FRONT LAMP BULB - REMOVAL.........8L-26
FRONT LAMP UNIT - INSTALLATION.....8L-28
FRONT LAMP UNIT - REMOVAL.........8L-27
FRONT MOUNT - INSTALLATION..........9-57
FRONT MOUNT - REMOVAL.............9-56
FRONT OUTPUT SHAFT SEAL -
INSTALLATION................21-208,21-246
FRONT OUTPUT SHAFT SEAL -
REMOVAL...................21-208,21-246
FRONT POSITION LAMP BULB -
INSTALLATION.......................8L-28
FRONT POSITION LAMP BULB -
REMOVAL
..........................8L-28
FRONT SEAL - INSTALLATION, OIL
PUMP
............................21-152
FRONT SEAL - REMOVAL, OIL PUMP
....21-152
FRONT SEAT BELT & RETRACTOR -
INSTALLATION
......................8O-24
FRONT SEAT BELT & RETRACTOR -
REMOVAL
..........................8O-23FRONT SEAT BELT BUCKLE -
INSTALLATION......................8O-26
FRONT SEAT BELT BUCKLE - REMOVAL . . 8O-25
FRONT SKID PLATE - INSTALLATION......13-6
FRONT SKID PLATE - REMOVAL..........13-6
FRONT SUSPENSION, SPECIAL TOOLS.....2-8
FRONT TOW HOOK - INSTALLATION......13-8
FRONT TOW HOOK - REMOVAL..........13-8
FRONT WASHER HOSES/TUBES -
DESCRIPTION.......................8R-10
FRONT WASHER HOSES/TUBES -
OPERATION.........................8R-10
FRONT WASHER NOZZLE -
DESCRIPTION.......................8R-11
FRONT WASHER NOZZLE -
INSTALLATION......................8R-11
FRONT WASHER NOZZLE - OPERATION . . . 8R-11
FRONT WASHER NOZZLE - REMOVAL....8R-11
FRONT WHEEL OPENING FLARE
MOLDINGS - INSTALLATION...........23-145
FRONT WHEEL OPENING FLARE
MOLDINGS - REMOVAL..............23-145
FRONT WHEEL SPEED SENSOR -
INSTALLATION........................5-34
FRONT WHEEL SPEED SENSOR -
REMOVAL...........................5-34
FRONT WHEELHOUSE SPLASH SHIELD -
INSTALLATION......................23-143
FRONT WHEELHOUSE SPLASH SHIELD -
REMOVAL.........................23-143
FRONT WIPER & WASHER SYSTEM -
CLEANING...........................8R-7
FRONT WIPER & WASHER SYSTEM -
DIAGNOSIS AND TESTING..............8R-6
FRONT WIPER & WASHER SYSTEM -
INSPECTION.........................8R-7
FRONT WIPER ARM - DESCRIPTION.....8R-12
FRONT WIPER ARM - INSTALLATION.....8R-13
FRONT WIPER ARM - OPERATION.......8R-12
FRONT WIPER ARM - REMOVAL........8R-12
FRONT WIPER BLADE - DESCRIPTION....8R-13
FRONT WIPER BLADE - INSTALLATION . . . 8R-14
FRONT WIPER BLADE - OPERATION.....8R-14
FRONT WIPER BLADE - REMOVAL.......8R-14
FRONT WIPER MODULE - DESCRIPTION . . 8R-15
FRONT WIPER MODULE - INSTALLATION . 8R-16
FRONT WIPER MODULE - OPERATION....8R-15
FRONT WIPER MODULE - REMOVAL.....8R-16
FRONT WIPERS/WASHERS -
DESCRIPTION........................8R-2
FRONT WIPERS/WASHERS - OPERATION . . 8R-4
FRONT WIPER/WASHER SWITCH -
DESCRIPTION.......................8R-16
FRONT WIPER/WASHER SWITCH -
OPERATION.........................8R-16
FUEL DELIVERY - DESCRIPTION..........14-2
FUEL DELIVERY - OPERATION...........14-3
FUEL FILL DOOR/HOUSING -
INSTALLATION......................23-141
FUEL FILL DOOR/HOUSING - REMOVAL . . 23-141
FUEL FILLER CAP - DESCRIPTION.......25-27
FUEL FILLER CAP - OPERATION.........25-27
FUEL FILTER - DESCRIPTION............14-7
FUEL FILTER - INSTALLATION............14-8
FUEL FILTER - REMOVAL...............14-7
FUEL GAUGE - DESCRIPTION...........8J-19
FUEL GAUGE - OPERATION.............8J-20
FUEL INDICATOR - DESCRIPTION, LOW
. . . 8J-22
FUEL INDICATOR - OPERATION, LOW
.....8J-22
FUEL INJECTION - DESCRIPTION
........14-29
FUEL INJECTOR - DESCRIPTION
.........14-33
FUEL INJECTOR - DIAGNOSIS AND
TESTING
...........................14-33
FUEL INJECTOR - OPERATION
..........14-33
FUEL LEVEL SENDING UNIT -
DIAGNOSIS AND TESTING
..............14-9
FUEL LEVEL SENDING UNIT / SENSOR -
DESCRIPTION
........................14-9
FUEL LEVEL SENDING UNIT / SENSOR -
INSTALLATION
.......................14-10
FUEL LEVEL SENDING UNIT / SENSOR -
OPERATION
..........................14-9
FUEL LEVEL SENDING UNIT / SENSOR -
REMOVAL
...........................14-9
FUEL LINES - DESCRIPTION
............14-10
FUEL PRESSURE LEAK DOWN TEST -
DIAGNOSIS AND TESTING
..............14-3
10 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

HEAD GASKET - DIAGNOSIS AND
TESTING, CYLINDER...............9-19,9-30
HEADLAMP BULB - INSTALLATION.......8L-32
HEADLAMP BULB - REMOVAL..........8L-31
HEADLAMP HIGH BEAM RELAY -
DESCRIPTION.......................8L-33
HEADLAMP HIGH BEAM RELAY -
DIAGNOSIS AND TESTING.............8L-34
HEADLAMP HIGH BEAM RELAY -
INSTALLATION.......................8L-35
HEADLAMP HIGH BEAM RELAY -
OPERATION.........................8L-33
HEADLAMP HIGH BEAM RELAY -
REMOVAL..........................8L-34
HEADLAMP LEVELING MOTOR -
DESCRIPTION.......................8L-35
HEADLAMP LEVELING MOTOR -
INSTALLATION.......................8L-36
HEADLAMP LEVELING MOTOR -
OPERATION.........................8L-36
HEADLAMP LEVELING MOTOR -
REMOVAL..........................8L-36
HEADLAMP LEVELING SWITCH -
DESCRIPTION.......................8L-37
HEADLAMP LEVELING SWITCH -
DIAGNOSIS AND TESTING.............8L-37
HEADLAMP LEVELING SWITCH -
INSTALLATION.......................8L-38
HEADLAMP LEVELING SWITCH -
OPERATION.........................8L-37
HEADLAMP LEVELING SWITCH -
REMOVAL..........................8L-38
HEADLAMP LOW BEAM RELAY -
DESCRIPTION.......................8L-39
HEADLAMP LOW BEAM RELAY -
DIAGNOSIS AND TESTING.............8L-40
HEADLAMP LOW BEAM RELAY -
INSTALLATION.......................8L-41
HEADLAMP LOW BEAM RELAY -
OPERATION.........................8L-39
HEADLAMP LOW BEAM RELAY -
REMOVAL..........................8L-40
HEADLAMP UNIT - ADJUSTMENT........8L-42
HEADLAMP UNIT - INSTALLATION.......8L-42
HEADLAMP UNIT - REMOVAL...........8L-41
HEADLINER - INSTALLATION..........23-159
HEADLINER - REMOVAL..............23-159
HEADREST - INSTALLATION...........23-164
HEADREST - REMOVAL...............23-164
HEADREST SLEEVE - INSTALLATION....23-164
HEADREST SLEEVE - REMOVAL........23-164
HEAT SHIELDS - DESCRIPTION..........11-4
HEAT STAKING - STANDARD
PROCEDURE.........................23-3
HEATED MIRRORS - DESCRIPTION.......8G-1
HEATED MIRRORS - DIAGNOSIS AND
TESTING............................8G-1
HEATED MIRRORS - OPERATION.........8G-1
HEATED SEAT ELEMENT - DESCRIPTION . . 8G-13
HEATED SEAT ELEMENT - DIAGNOSIS
AND TESTING.......................8G-13
HEATED SEAT ELEMENT - OPERATION....8G-13
HEATED SEAT MODULE - DESCRIPTION . . . 8E-21
HEATED SEAT MODULE - DIAGNOSIS
AND TESTING.......................8E-22
HEATED SEAT MODULE - INSTALLATION . . 8E-24
HEATED SEAT MODULE - OPERATION....8E-21
HEATED SEAT MODULE - REMOVAL......8E-24
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING.......................8G-14
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING
..................8G-12,8G-14
HEATED SEAT SYSTEM - DESCRIPTION
. . . 8G-10
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING
.......................8G-11
HEATED SEAT SYSTEM - OPERATION
....8G-10
HEATER AND AIR CONDITIONER -
DESCRIPTION
........................24-1
HEATER AND AIR CONDITIONER -
OPERATION
..........................24-2
HEATER CONTROL - DESCRIPTION, A/C
. . . 24-16
HEATER CONTROL - INSTALLATION, A/C
. . 24-17
HEATER CONTROL - REMOVAL, A/C
......24-17
HEATER CORE - DESCRIPTION
..........24-52
HEATER CORE - INSTALLATION
.........24-53
HEATER CORE - OPERATION
............24-52
HEATER CORE - REMOVAL
.............24-52HEATER PERFORMANCE - DIAGNOSIS
AND TESTING........................24-6
HEATER SWITCH - DESCRIPTION,
DRIVER SEAT.......................8G-11
HEATER SWITCH - DESCRIPTION,
PASSENGER SEAT....................8G-14
HEATER SWITCH - INSTALLATION,
DRIVER SEAT.......................8G-13
HEATER SWITCH - INSTALLATION,
PASSENGER SEAT....................8G-15
HEATER SWITCH - OPERATION, DRIVER
SEAT ..............................8G-12
HEATER SWITCH - OPERATION,
PASSENGER SEAT....................8G-14
HEATER SWITCH - REMOVAL, DRIVER
SEAT ..............................8G-13
HEATER SWITCH - REMOVAL,
PASSENGER SEAT....................8G-15
HEATER-A/C CONTROL ILLUMINATION
BULB - INSTALLATION................8L-78
HEATER-A/C CONTROL ILLUMINATION
BULB - REMOVAL....................8L-78
HEATING GRID REPAIR - STANDARD
PROCEDURE, REAR GLASS.............8G-4
HEIGHT MEASUREMENT - STANDARD
PROCEDURE..........................2-4
HIGH AND LOW LIMITS - DESCRIPTION . . 25-20
HIGH BEAM INDICATOR - DESCRIPTION . . 8J-22
HIGH BEAM INDICATOR - OPERATION....8J-22
HIGH BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-33
HIGH BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP...................8L-34
HIGH BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-35
HIGH BEAM RELAY - OPERATION,
HEADLAMP.........................8L-33
HIGH BEAM RELAY - REMOVAL,
HEADLAMP.........................8L-34
HIGH MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER...............8L-19
HIGH MOUNTED STOP LAMP BULB -
REMOVAL, CENTER...................8L-18
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER...............8L-19
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER...................8L-19
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION.......................24-42
HIGH PRESSURE RELIEF VALVE -
OPERATION.........................24-42
HIGH PRESSURE SWITCH -
DESCRIPTION, A/C...................24-17
HIGH PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-18
HIGH PRESSURE SWITCH -
INSTALLATION, A/C...................24-18
HIGH PRESSURE SWITCH - OPERATION,
A/C................................24-18
HIGH PRESSURE SWITCH - REMOVAL,
A/C................................24-18
HIGH/LOW RELAY - DESCRIPTION,
WIPER.............................8R-23
HIGH/LOW RELAY - DIAGNOSIS AND
TESTING, WIPER.....................8R-24
HIGH/LOW RELAY - INSTALLATION,
WIPER.............................8R-24
HIGH/LOW RELAY - OPERATION, WIPER . . 8R-23
HIGH/LOW RELAY - REMOVAL, WIPER . . . 8R-24
HINGE - INSTALLATION . . 23-119,23-123,23-131,
23-137
HINGE - REMOVAL......23-119,23-123,23-131,
23-137
HITCH - INSTALLATION, TRAILER.........13-9
HITCH - REMOVAL, TRAILER............13-9
HOISTING RECOMMENDATIONS -
STANDARD PROCEDURE.................0-4
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-17
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-17
HOLDDOWN - OPERATION, BATTERY.....8F-17
HOLDDOWN - REMOVAL, BATTERY......8F-17
HOLDING CLUTCHES - DESCRIPTION
....21-131
HOLDING CLUTCHES - OPERATION
.....21-132
HOLE REPAIR - DESCRIPTION,
THREADED
........................Intro.-4
HONING - STANDARD PROCEDURE,
CYLINDER BORE
......................9-39
HOOD - INSTALLATION
...............23-119HOOD - REMOVAL...................23-119
HOOD AJAR SWITCH - DESCRIPTION....8Q-11
HOOD AJAR SWITCH - DIAGNOSIS AND
TESTING...........................8Q-12
HOOD AJAR SWITCH - INSTALLATION....8Q-12
HOOD AJAR SWITCH - OPERATION......8Q-12
HOOD AJAR SWITCH - REMOVAL.......8Q-12
HOOD AJAR SWITCH BRACKET -
INSTALLATION......................8Q-13
HOOD AJAR SWITCH BRACKET -
REMOVAL..........................8Q-13
HOOD AJAR SWITCH STRIKER -
INSTALLATION......................8Q-14
HOOD AJAR SWITCH STRIKER -
REMOVAL..........................8Q-13
HOOK - INSTALLATION, FRONT TOW......13-8
HOOK - INSTALLATION, REAR TOW.......13-8
HOOK - REMOVAL, FRONT TOW..........13-8
HOOK - REMOVAL, REAR TOW...........13-8
HORN - DIAGNOSIS AND TESTING.......8H-2
HORN - INSTALLATION.................8H-3
HORN - REMOVAL....................8H-3
HORN RELAY - DIAGNOSIS AND
TESTING............................8H-3
HORN RELAY - INSTALLATION...........8H-3
HORN RELAY - REMOVAL..............8H-3
HORN SWITCH - DESCRIPTION..........8H-4
HORN SWITCH - DIAGNOSIS AND
TESTING..............................8H-4
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - INSTALLATION, FRONT BRAKE.....5-10
HOSE - INSTALLATION, PRESSURE......19-21
HOSE - INSTALLATION, REAR BRAKE......5-10
HOSE - REMOVAL, FRONT...............5-9
HOSE - REMOVAL, PRESSURE..........19-21
HOSE - REMOVAL, REAR BRAKE..........5-9
HOSE CLAMPS - DESCRIPTION...........7-2
HOSE CLAMPS - OPERATION.............7-3
HOSE (GEAR TO THE COOLER) -
INSTALLATION, RETURN...............19-22
HOSE (GEAR TO THE COOLER) -
REMOVAL, RETURN..................19-21
HOSE (RESERVOIR TO THE COOLER) -
INSTALLATION, RETURN...............19-22
HOSE (RESERVOIR TO THE COOLER) -
REMOVAL, RETURN..................19-21
HOSES - DIAGNOSIS AND TESTING,
BRAKE LINE..........................5-8
HOSES/LINES/TUBES PRECAUTIONS -
CAUTION, REFRIGERANT
..............24-40
HOSES/TUBES - DESCRIPTION, FRONT
WASHER
...........................8R-10
HOSES/TUBES - DESCRIPTION, REAR
WASHER
...........................8R-35
HOSES/TUBES - OPERATION, FRONT
WASHER
...........................8R-10
HOSES/TUBES - OPERATION, REAR
WASHER
...........................8R-36
HOUSING - ASSEMBLY, HVAC
...........24-34
HOUSING - DISASSEMBLY, HVAC
........24-34
HOUSING - INSTALLATION, HVAC
........24-34
HOUSING - REMOVAL, HVAC
...........24-33
HOUSING BUSHING - NV3550 -
INSTALLATION, EXTENSION
............21-74
HOUSING BUSHING - NV3550 -
REMOVAL, EXTENSION
................21-73
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER
................21-80
HOUSING SEAL - INSTALLATION,
ADAPTER
..........................21-124
HOUSING SEAL - NV1500 -
INSTALLATION, EXTENSION
............21-32
HOUSING SEAL - NV1500 - REMOVAL,
EXTENSION
.........................21-32
HOUSING SEAL - NV3550 -
INSTALLATION, EXTENSION
............21-74
HOUSING SEAL - NV3550 - REMOVAL,
EXTENSION
.........................21-74
HOUSING SEAL - REMOVAL, ADAPTER
. . 21-124
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION
.....................8W-01-1
HUB / BEARING - INSTALLATION
..........2-9
HUB / BEARING - REMOVAL
..............2-9
12 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

LATCH - ACCESS PANEL - REMOVAL....23-139
LATCH - INSTALLATION . . 23-120,23-124,23-131,
23-137
LATCH - INSTALLATION, FLIP-UP GLASS . 23-136
LATCH - INSTALLATION, FLOOR
CONSOLE LID......................23-158
LATCH - INSTALLATION, GLOVE BOX....23-148
LATCH / LOCK - INSTALLATION,
FOLDING REAR SEAT BACK...........23-170
LATCH / LOCK - REMOVAL, FOLDING
REAR SEAT BACK...................23-170
LATCH - REMOVAL......23-120,23-124,23-131,
23-137
LATCH - REMOVAL, FLIP-UP GLASS.....23-136
LATCH - REMOVAL, FLOOR CONSOLE
LID...............................23-158
LATCH - REMOVAL, GLOVE BOX........23-148
LATCH RELEASE CABLE - INSTALLATION . 23-120
LATCH RELEASE CABLE - REMOVAL....23-120
LATCH RELEASE HANDLE -
INSTALLATION......................23-120
LATCH RELEASE HANDLE - REMOVAL . . . 23-120
LATCH STRIKER - INSTALLATION......23-124,
23-132,23-137
LATCH STRIKER - INSTALLATION, GLOVE
BOX ..............................23-149
LATCH STRIKER - INSTALLATION, REAR
SEAT BACK........................23-171
LATCH STRIKER - REMOVAL....23-124,23-132,
23-137
LATCH STRIKER - REMOVAL, GLOVE
BOX ..............................23-148
LATCH STRIKER - REMOVAL, REAR
SEAT BACK........................23-170
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID...........21-80
LEAK - DIAGNOSIS AND TESTING,
ENGINE OIL..........................9-60
LEAK DETECTION PUMP - DESCRIPTION . . 25-27
LEAK DETECTION PUMP - INSTALLATION . 25-28
LEAK DETECTION PUMP - OPERATION....25-28
LEAK DETECTION PUMP - REMOVAL.....25-28
LEAK DOWN TEST - DIAGNOSIS AND
TESTING, FUEL PRESSURE..............14-3
LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE.......9-8
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-4
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD....................9-68
LEAKS - DIAGNOSIS AND TESTING,
REAR SEAL AREA.....................9-61
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-2
LEAKS - STANDARD PROCEDURE,
REPAIRING..........................22-8
LEARN - STANDARD PROCEDURE, TCM
QUICK.............................8E-21
LEFT POWER SEAT SWITCH -
DESCRIPTION.......................8N-16
LEFT POWER SEAT SWITCH -
DIAGNOSIS AND TESTING.............8N-17
LEFT POWER SEAT SWITCH -
INSTALLATION......................8N-18
LEFT POWER SEAT SWITCH -
OPERATION
.........................8N-17
LEFT POWER SEAT SWITCH - REMOVAL
. . 8N-18
LEFT SIDE - INSTALLATION
.........2-12,2-15
LEFT SIDE - REMOVAL
.............2-11,2-15
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID
........21-125
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL
...................24-54
LEVEL - STANDARD PROCEDURES,
MASTER CYLINDER FLUID
..............5-26
LEVEL CHECK - STANDARD
PROCEDURE, FLUID
.................21-126
LEVEL SENDING UNIT - DIAGNOSIS AND
TESTING, FUEL
.......................14-9
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL
...................14-9
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL
.................14-10
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL
.....................14-9
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL
......................14-9LEVEL SWITCH - DESCRIPTION,
WASHER FLUID.....................8R-17
LEVEL SWITCH - INSTALLATION,
WASHER FLUID.....................8R-18
LEVEL SWITCH - OPERATION, WASHER
FLUID.............................8R-17
LEVEL SWITCH - REMOVAL, WASHER
FLUID.............................8R-17
LEVELING MOTOR - DESCRIPTION,
HEADLAMP.........................8L-35
LEVELING MOTOR - INSTALLATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - OPERATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - REMOVAL,
HEADLAMP.........................8L-36
LEVELING SWITCH - DESCRIPTION,
HEADLAMP.........................8L-37
LEVELING SWITCH - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-37
LEVELING SWITCH - INSTALLATION,
HEADLAMP.........................8L-38
LEVELING SWITCH - OPERATION,
HEADLAMP.........................8L-37
LEVELING SWITCH - REMOVAL,
HEADLAMP.........................8L-38
LEVER - INSTALLATION................5-31
LEVER - INSTALLATION, SHIFT . . . 21-214,21-249
LEVER - REMOVAL....................5-31
LEVER - REMOVAL, SHIFT......21-213,21-248
LHD - INSTALLATION...............8W-97-6
LHD - REMOVAL....................8W-97-5
LICENSE PLATE LAMP BULB -
INSTALLATION.......................8L-45
LICENSE PLATE LAMP BULB - REMOVAL . . 8L-44
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-46
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-45
LID LATCH - INSTALLATION, FLOOR
CONSOLE..........................23-158
LID LATCH - REMOVAL, FLOOR
CONSOLE..........................23-158
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIMITS - DESCRIPTION, HIGH AND LOW . . 25-20
LINE - DESCRIPTION, REFRIGERANT.....24-38
LINE - INSTALLATION, A/C DISCHARGE . . . 24-47
LINE - INSTALLATION, A/C LIQUID.......24-47
LINE - INSTALLATION, A/C SUCTION.....24-49
LINE - REMOVAL, A/C DISCHARGE.......24-46
LINE - REMOVAL, A/C LIQUID...........24-47
LINE - REMOVAL, A/C SUCTION.........24-48
LINE AND HOSES - DIAGNOSIS AND
TESTING, BRAKE.......................5-8
LINE PRESSURE (LP) SENSOR -
DESCRIPTION......................21-144
LINE PRESSURE (LP) SENSOR -
INSTALLATION......................21-144
LINE PRESSURE (LP) SENSOR -
OPERATION........................21-144
LINE PRESSURE (LP) SENSOR -
REMOVAL.........................21-144
LINES - DESCRIPTION, BRAKE............5-8
LINES - DESCRIPTION, FUEL...........14-10
LINES - DESCRIPTION, VACUUM........25-33
LINK - INSTALLATION, STABILIZER.......2-14
LINK - REMOVAL, STABILIZER...........2-14
LINK CONNECTOR - DESCRIPTION, DATA . 8E-10
LINK CONNECTOR - OPERATION, DATA . . . 8E-10
LINKAGE - INSTALLATION................6-9
LINKAGE - REMOVAL...................6-8
LINKAGE - STANDARD PROCEDURE,
STEERING..........................19-16
LIQUID LINE - INSTALLATION, A/C.......24-47
LIQUID LINE - REMOVAL, A/C...........24-47
LOAD TEST - STANDARD PROCEDURE....8F-12
LOAD VALUE - DESCRIPTION
...........25-20
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL
......8W-01-9
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE
...................8W-91-1
LOCATIONS - DESCRIPTION, FLUID
FILL/CHECK
...........................0-4
LOCATIONS - SPECIFICATIONS, SEALER
. . 23-87LOCATIONS - SPECIFICATIONS, WELD
AND STRUCTURAL ADHESIVE...........23-9
LOCK - INSTALLATION, FOLDING REAR
SEAT BACK LATCH..................23-170
LOCK - REMOVAL, FOLDING REAR SEAT
BACK LATCH.......................23-170
LOCK / UNLOCK SWITCH -
INSTALLATION, DOOR.................8N-5
LOCK / UNLOCK SWITCH - REMOVAL,
DOOR..............................8N-4
LOCK CYLINDER - INSTALLATION......23-125,
23-138
LOCK CYLINDER - INSTALLATION.......19-11
LOCK CYLINDER - REMOVAL....23-125,23-137
LOCK CYLINDER - REMOVAL...........19-10
LOCK MOTOR - DESCRIPTION, DOOR.....8N-5
LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR......................8N-5
LOCK MOTOR - OPERATION, DOOR.......8N-5
LOCK OUT - ADJUSTMENT..............5-30
LOCK RELAY - DESCRIPTION, DOOR......8N-6
LOCK RELAY - DIAGNOSIS AND
TESTING, DOOR......................8N-6
LOCK RELAY - INSTALLATION, DOOR.....8N-7
LOCK RELAY - OPERATION, DOOR........8N-6
LOCK RELAY - REMOVAL, DOOR.........8N-6
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER...........................8Q-9
LOCK SWITCH - DESCRIPTION,
TAILGATE CYLINDER...................8N-9
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR CYLINDER............8Q-10
LOCK SWITCH - DIAGNOSIS AND
TESTING, TAILGATE CYLINDER..........8N-9
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - INSTALLATION,
TAILGATE CYLINDER..................8N-10
LOCK SWITCH - OPERATION, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - OPERATION, TAILGATE
CYLINDER...........................8N-9
LOCK SWITCH - REMOVAL, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - REMOVAL, TAILGATE
CYLINDER..........................8N-10
LOCKS - DESCRIPTION, POWER.........8N-1
LOCKS - DIAGNOSIS AND TESTING,
POWER.............................8N-3
LOCKS - OPERATION, POWER...........8N-3
LOCK/UNLOCK SWITCH - DIAGNOSIS
AND TESTING, DOOR..................8N-4
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-38
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-37
LOW BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-40
LOW BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-41
LOW BEAM RELAY - OPERATION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - REMOVAL,
HEADLAMP
.........................8L-40
LOW FUEL INDICATOR - DESCRIPTION
. . . 8J-22
LOW FUEL INDICATOR - OPERATION
.....8J-22
LOW INDICATOR - DESCRIPTION,
COOLANT
...........................8J-15
LOW INDICATOR - OPERATION,
COOLANT
...........................8J-16
LOW LIMITS - DESCRIPTION, HIGH
......25-20
LOW MODE INDICATOR - DESCRIPTION,
FOUR
..............................8J-29
LOW MODE INDICATOR - OPERATION,
FOUR
..............................8J-30
LOW OIL PRESSURE INDICATOR -
DESCRIPTION
.......................8J-23
LOW OIL PRESSURE INDICATOR -
OPERATION
.........................8J-23
LOW PRESSURE SWITCH -
DESCRIPTION, A/C
...................24-18
LOW PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C
...................24-19
LOW PRESSURE SWITCH -
INSTALLATION, A/C
...................24-19
KJINDEX 15
Description Group-Page Description Group-Page Description Group-Page

PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-46
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-45
PLATES - INSTALLATION, EXTERIOR
NAME............................23-141
PLATES - REMOVAL, EXTERIOR NAME . . . 23-140
PLUG - CLEANING SPARK PLUGS,
SPARK .............................8I-15
PLUG - DESCRIPTION, SPARK...........8I-12
PLUG - INSTALLATION, SPARK..........8I-15
PLUG - OPERATION, SPARK............8I-12
PLUG - REMOVAL, SPARK..............8I-15
PLUG CABLE RESISTANCE, 2.4L - SPARK . . . 8I-3
PLUG CONDITIONS - DIAGNOSIS AND
TESTING, SPARK.....................8I-13
PLUGS - STANDARD PROCEDURE,
ENGINE CORE AND OIL GALLERY........9-10
PLUGS, SPARK PLUG - CLEANING
SPARK .............................8I-15
PLUGS, SPECIFICATIONS - SPARK........8I-3
POLISHING - DESCRIPTION, FINESSE
SANDING/BUFFING..................23-163
PORT - DESCRIPTION, REFRIGERANT
SYSTEM SERVICE.....................24-2
PORT - OPERATION, REFRIGERANT
SYSTEM SERVICE.....................24-2
POSITION LAMP BULB - INSTALLATION,
FRONT.............................8L-28
POSITION LAMP BULB - REMOVAL,
FRONT.............................8L-28
POSITION SENSOR - DESCRIPTION . 21-209,21-247
POSITION SENSOR - DESCRIPTION,
CRANKSHAFT.......................14-30
POSITION SENSOR - DESCRIPTION,
THROTTLE..........................14-47
POSITION SENSOR - INSTALLATION....21-210,
21-247
POSITION SENSOR - INSTALLATION,
CRANKSHAFT.......................14-32
POSITION SENSOR - INSTALLATION,
THROTTLE..........................14-48
POSITION SENSOR - OPERATION . 21-209,21-247
POSITION SENSOR - OPERATION,
CRANKSHAFT.......................14-31
POSITION SENSOR - OPERATION,
THROTTLE..........................14-47
POSITION SENSOR - REMOVAL . . 21-210,21-247
POSITION SENSOR - REMOVAL,
CRANKSHAFT.......................14-31
POSITION SENSOR - REMOVAL,
THROTTLE..........................14-47
POSITION SWITCH - DESCRIPTION,
CLUTCH PEDAL.......................6-11
POSITION SWITCH - DIAGNOSIS AND
TESTING, CLUTCH PEDAL...............6-11
POSITION SWITCH - OPERATION,
CLUTCH PEDAL.......................6-11
POTENTIAL - STANDARD PROCEDURE,
TESTING OF VOLTAGE..............8W-01-9
POWER BRAKE BOOSTER -
DESCRIPTION........................5-21
POWER BRAKE BOOSTER -
INSTALLATION........................5-23
POWER BRAKE BOOSTER - OPERATION . . . 5-21
POWER BRAKE BOOSTER - REMOVAL.....5-22
POWER DISTRIBUTION - DESCRIPTION . 8W-97-1
POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION CENTER -
DESCRIPTION.....................8W-97-6
POWER DISTRIBUTION CENTER -
OPERATION.......................8W-97-7
POWER DISTRIBUTION CENTER -
REMOVAL........................8W-97-7
POWER DISTRIBUTION CENTER
ASSEMBLY, ASSEMBLY.............8W-97-10
POWER DISTRIBUTION CENTER
DISASSEMBLY, DISASSEMBLY........8W-97-7
POWER DISTRIBUTION SYSTEMS,
SPECIAL TOOLS...................8W-97-2
POWER GROUNDS - DESCRIPTION......8E-13
POWER LOCKS - DESCRIPTION
..........8N-1
POWER LOCKS - DIAGNOSIS AND
TESTING
............................8N-3
POWER LOCKS - OPERATION
............8N-3
POWER MIRROR SWITCH - DIAGNOSIS
AND TESTING
.......................8N-12
POWER MIRROR SWITCH -
INSTALLATION
......................8N-13POWER MIRROR SWITCH - REMOVAL . . . 8N-13
POWER MIRRORS - DESCRIPTION......8N-11
POWER MIRRORS - DIAGNOSIS AND
TESTING...........................8N-11
POWER MIRRORS - OPERATION........8N-11
POWER OUTLET - DESCRIPTION.....8W-97-11
POWER OUTLET - DIAGNOSIS AND
TESTING........................8W-97-11
POWER OUTLET - INSTALLATION....8W-97-13
POWER OUTLET - OPERATION.......8W-97-11
POWER OUTLET - REMOVAL........8W-97-12
POWER SEAT SWITCH - DESCRIPTION,
LEFT..............................8N-16
POWER SEAT SWITCH - DESCRIPTION,
RIGHT.............................8N-19
POWER SEAT SWITCH - DIAGNOSIS
AND TESTING, LEFT..................8N-17
POWER SEAT SWITCH - DIAGNOSIS
AND TESTING, RIGHT.................8N-19
POWER SEAT SWITCH - INSTALLATION,
LEFT..............................8N-18
POWER SEAT SWITCH - INSTALLATION,
RIGHT.............................8N-20
POWER SEAT SWITCH - OPERATION,
LEFT..............................8N-17
POWER SEAT SWITCH - OPERATION,
RIGHT.............................8N-19
POWER SEAT SWITCH - REMOVAL, LEFT . 8N-18
POWER SEAT SWITCH - REMOVAL,
RIGHT.............................8N-20
POWER SEATS - DESCRIPTION...........8N-14
POWER SEATS - DIAGNOSIS AND
TESTING...........................8N-15
POWER SEATS - OPERATION...........8N-15
POWER STEERING FLOW AND
PRESSURE - DIAGNOSIS AND
TESTING............................19-3
POWER STEERING PRESSURE SWITCH -
DESCRIPTION.......................19-22
POWER STEERING PRESSURE SWITCH -
INSTALLATION.......................19-22
POWER STEERING PRESSURE SWITCH -
OPERATION.........................19-22
POWER STEERING PRESSURE SWITCH -
REMOVAL..........................19-22
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE . . . 19-18
POWER STEERING PUMP, SPECIAL
TOOLS.............................19-20
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING..............19-1
POWER WINDOWS - DESCRIPTION......8N-21
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-21
POWER WINDOWS - OPERATION........8N-21
POWERED - STARTER MOTOR, GAS......8F-39
POWERED - TORQUE, GAS.............8F-38
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-9
PRECAUTIONS - CAUTION,
REFRIGERANT HOSES/LINES/TUBES
......24-40
PRECAUTIONS - OPERATION, SERVICE
....19-5
PRECAUTIONS AND WARNINGS,
WARNING - SAFETY
...................23-1
PRECAUTIONS, WARNING -
WINDSHIELD SAFETY
................23-173
PREFERENCES - STANDARD
PROCEDURE, RKE TRANSMITTER
CUSTOMER
..........................8N-8
PRELIMINARY - DIAGNOSIS AND
TESTING
...........................21-78
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING
.........................7-3
PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET
SURFACE
.............................9-9
PRESS CONTAINER - DESCRIPTION,
COOLANT RECOVERY
..................7-19
PRESS CONTAINER - OPERATION,
COOLANT RECOVERY
..................7-19
PRESSURE - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION
...............9-8
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL
..........................9-60
PRESSURE - DIAGNOSIS AND TESTING,
POWER STEERING FLOW
...............19-3PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-5
PRESSURE CAP - CLEANING, RADIATOR . . . 7-25
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-25
PRESSURE CAP - DIAGNOSIS AND
TESTING, RADIATOR...................7-25
PRESSURE CAP - INSPECTION,
RADIATOR...........................7-25
PRESSURE CAP - OPERATION,
RADIATOR...........................7-25
PRESSURE HOSE - INSTALLATION.......19-21
PRESSURE HOSE - REMOVAL..........19-21
PRESSURE INDICATOR - DESCRIPTION,
LOW OIL ...........................8J-23
PRESSURE INDICATOR - OPERATION,
LOW OIL ...........................8J-23
PRESSURE LEAK DOWN TEST -
DIAGNOSIS AND TESTING, FUEL.........14-3
PRESSURE LEAKAGE - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION........9-8
PRESSURE (LP) SENSOR -
DESCRIPTION, LINE.................21-144
PRESSURE (LP) SENSOR -
INSTALLATION, LINE.................21-144
PRESSURE (LP) SENSOR - OPERATION,
LINE..............................21-144
PRESSURE (LP) SENSOR - REMOVAL,
LINE..............................21-144
PRESSURE REGULATOR - DESCRIPTION,
FUEL..............................14-13
PRESSURE REGULATOR -
INSTALLATION, FUEL...................14-14
PRESSURE REGULATOR - OPERATION,
FUEL..............................14-14
PRESSURE REGULATOR - REMOVAL,
FUEL..............................14-14
PRESSURE RELEASE - STANDARD
PROCEDURE, FUEL SYSTEM.............14-4
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH..................24-42
PRESSURE RELIEF VALVE - OPERATION,
HIGH..............................24-42
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL....................9-65
PRESSURE SENSOR/SWITCH -
INSTALLATION, OIL....................9-65
PRESSURE SENSOR/SWITCH -
OPERATION, OIL......................9-65
PRESSURE SENSOR/SWITCH -
REMOVAL, OIL.......................9-65
PRESSURE, SPECIFICATIONS - FUEL
SYSTEM............................14-5
PRESSURE SWITCH - DESCRIPTION, A/C
HIGH..............................24-17
PRESSURE SWITCH - DESCRIPTION, A/C
LOW ..............................24-18
PRESSURE SWITCH - DESCRIPTION,
POWER STEERING...................19-22
PRESSURE SWITCH - DIAGNOSIS AND
TESTING, A/C HIGH...................24-18
PRESSURE SWITCH - DIAGNOSIS AND
TESTING, A/C LOW
...................24-19
PRESSURE SWITCH - INSTALLATION,
A/C HIGH
...........................24-18
PRESSURE SWITCH - INSTALLATION,
A/C LOW
...........................24-19
PRESSURE SWITCH - INSTALLATION,
POWER STEERING
...................19-22
PRESSURE SWITCH - OPERATION, A/C
HIGH
..............................24-18
PRESSURE SWITCH - OPERATION, A/C
LOW
..............................24-18
PRESSURE SWITCH - OPERATION,
POWER STEERING
...................19-22
PRESSURE SWITCH - REMOVAL, A/C
HIGH
..............................24-18
PRESSURE SWITCH - REMOVAL, A/C
LOW
..............................24-19
PRESSURE SWITCH - REMOVAL,
POWER STEERING
...................19-22
PRESSURE TEST - DIAGNOSIS AND
TESTING, FUEL PUMP
.................14-15
PRESSURE TEST - DIAGNOSIS AND
TESTING, HYDRAULIC
.................21-79
PRIMARY WEATHERSTRIP -
INSTALLATION, DOOR
................23-185
KJINDEX 19
Description Group-Page Description Group-Page Description Group-Page