ESP Lexus ES300 2001 s (in English) Owner's Guide

DRIVING TIPS
333
Tires
Ensure that your vehicle's tires are properly inflated.
Adjust the tire pressure to the recommended cold tire
pressure indicated below:
Tire pressure, kPa (kgf/cm
2 or bar, psi)
Front 220 (2.2, 32)
Rear 220 (2.2, 32)
 The trailer tires should be inflated to the pressure
recommended by the trailer manufacturer in respect
to the total trailer weight.
Trailer lights
Trailer lights must comply with federal,
state/provincial and local regulations. See your local
recreational vehicle dealer or rental agency for the
correct type of wiring and relays for your trailer.
Check for correct operation of the turn signals and
stop lights each time you hitch up. Direct splicing may
damage your vehicle's electrical system and cause a
malfunction of your lights.
Break±in schedule
 Lexus recommends that you do not tow a trailer with
a new vehicle or a vehicle with any new power train
component (engine, transmission, differential, wheel
bearing, etc.) for the first 800 km (500 miles) of
driving.
Maintenance
If you tow a trailer, your vehicle will require more
frequent maintenance due to the additional load. For
this information, please refer to the scheduled
maintenance information in the ªOwner's Manual
Supplement/ Maintenance Scheduleº.
 Retighten all fixing bolts of the towing ball and bracket
after approximately 1000 km (600 miles) of trailer
driving.
Pre±towing safety check
 Check that your vehicle remains level when a loaded
or unloaded trailer is hitched. Do not drive if the
vehicle has an abnormal nose±up or nose±down
condition, and check for improper tongue load,
overload, worn suspension or other possible causes.
 Make sure the trailer cargo is securely loaded so that
it cannot shift.
 Check that your rear view mirrors conform to any
federal, state/provincial or local regulations. If they
do not, install required rear view mirrors appropriate
for towing purposes.

DRIVING TIPS
334
Trailer towing tips
When towing a trailer, your vehicle will handle
differently than when not towing. The three main
causes of vehicle±trailer accidents are driver error,
excessive speed and improper trailer loading. Keep
these in mind when towing: 
Before starting out, check the operation of the lights
and all vehicle±trailer connections. After driving a
short distance, stop and recheck the lights and
connections. Practice turning, stopping and backing
with a trailer in an area away from traffic until you learn
the feel.
 Backing with a trailer is difficult and requires practice.
Grip the bottom of the steering wheel and move your
hand to the left to move the trailer to the left. Move
your hand to the right to move the trailer to the right.
(This procedure is generally opposite to that when
backing without a trailer.) Also, just turn the steering
wheel a little at a time, avoiding sharp or prolonged
turning. Have someone guide you when backing to
reduce the risk of an accident.
 Because stopping distance may be increased,
vehicle±to±vehicle distance should be increased
when towing a trailer. For each 16 km/h (10 mph) of
speed, allow at least one vehicle and trailer length
between you and the vehicle ahead. Avoid sudden
braking as you may skid, resulting in jackknifing and
loss of control. This is especially true on wet or
slippery surfaces.
 Avoid jerky starts or sudden acceleration.
 Avoid jerky steering and sharp turns. The trailer could
hit your vehicle in a tight turn. Slow down before
making a turn to avoid the need of sudden braking.
 Remember that when making a turn, the trailer

MAINTENANCE
380
MAINTENANCE
REQUIREMENTS
Your Lexus vehicle has been designed to have fewer
maintenance requirements with longer service intervals
to save both your time and money. However, each
regular maintenance as well as day±to±day care is more
important than ever before to ensure smooth,
trouble±free, safe, and economical driving.
It is the owner's responsibility to make sure the specified
maintenance, including general maintenance services,
is performed. Note that both the new vehicle and
emission control system warranties specify that proper
maintenance and care must be performed. See the
ªOwner's Guideº, ªOwner's Manual Supplementº or
ªWarranty Bookletº for complete warranty information.
General maintenance
General maintenance items are those day±to±day care
practices that are important to your vehicle for proper
operation. It is the owner's responsibility to ensure that
the general maintenance items are performed regularly.
These checks or inspections can be done either by
yourself or your Lexus dealer.
Scheduled maintenance
The scheduled maintenance items listed in the ªOwner's
Manual Supplement/Maintenance Scheduleº are those
required to be serviced at regular intervals.
For details of your maintenance schedule, read the
ªOwner's Manual Supplement/Maintenance Scheduleº.
It is recommended that any replacement parts used
for maintenance or for the repair of the emission
control system be Lexus supplied.
The owner may elect to use non±Lexus supplied
parts for replacement purposes without invalidating
the emission control system warranty. However,
use of replacement parts which are not of equivalent
quality may impair the effectiveness of the emission
control systems.
You may also elect to have maintenance,
replacement, or repair of the emission control
devices and system performed by any automotive
repair establishment or individual without
invalidating this warranty. See ªOwner's Guideº,
ªOwner's Manual Supplementº or ªWarranty
Bookletº for complete warranty information.

INTRODUCTION
392
DO±IT±YOURSELF SERVICEPRECAUTIONS
If you perform maintenance yourself, be sure to
follow the correct procedure given in this section.
You should be aware that improper or incomplete
servicing may result in operating problems.
Performing do±it±yourself maintenance during the
warranty period may affect your warranty coverage.
Read the separate Lexus Warranty statement for details
and suggestions.
This section gives instructions only for those items that
are relatively easy for an owner to perform. As explained
in Section 5, there are still a number of items that must
be performed by a qualified technician with special tools.
For information on tools and parts for do±it±yourself
maintenance, see ªParts and toolsº on page 394.
Utmost care should be taken when working on your
vehicle to prevent accidental injury. Here are a few
precautions that you should be especially careful to
observe:

CHASSIS
436controlled conditions on specified government test
surfaces of asphalt and concrete. A tire marked C may
have poor traction performance.
Warning: The traction grade assigned to this tire is
based on braking (straight ahead) traction tests and
does not include cornering (turning) traction.
Temperature A, B, C
± The temperature grades are A
(the highest), B, and C, representing the tire's resistance
to the generation of heat and its ability to dissipate heat
when tested under controlled conditions on a specified
indoor laboratory test wheel. Sustained high
temperature can cause the material of the tire to
degenerate and reduce tire life, and excessive
temperature can lead to sudden tire failure. The grade
C corresponds to a level of performance which all
passenger car tires must meet under the Federal Motor
Vehicle Safety Standard No. 109. Grades B and A
represent higher levels of performance on the laboratory
test wheel than the minimum required by law.
Warning: The temperature grade for this tire established
for a tire that is properly inflated and not overloaded.
Excessive speed, underinflation, or excessive loading,
either separately or in combination, can cause heat
buildup and possible tire failure.

ELECTRICAL COMPONENTS
450
No.FUSEAMPERECIRCUIT
28 WIPER25Windshield wipers and
washer
29 MIRROR
±HEATER10Outside rear view mirror
defogger
30 ECU±IG15
Cruise control system,
Anti±lock brake system,
Shift lock system, Theft
deterrent system,
Electronic modulated
suspension, Wireless
remote control
31 IGN5SRS, Multiport fuel
injection
32 STOP15
Stop lights, High mounted
stoplight, Cruise control
system, Electronic
modulated suspension,
Anti±lock brake system,
Shift lock system, Power
seat system, Multiport
fuel injection
33 TAIL10Tail light, Side marker
lights, License plate lights
34 POWER
±OUTLET15Power outlet
35 OBD7.5On±board diagnosis
system
36 FOG15Fog lights
No.FUSEAMPERECIRCUIT
37 STARTER5Starting system
38 DOOR25
Door courtesy light, Theft
deterrent system, Power
door lock system, Trunk
lid opener, Fuel filler door
opener
39 PANEL7.5Instrument panel lights,
Glove box light
40 TURN7.5Emergency flashers, Turn
signal lights
41 RAD± NO.27.5Audio system
42 CIG15Cigarette lighter, Clock,
SRS
43 DEF40Rear window defogger,
Outside rear view mirror
defogger
44 PWR30Power window, Electronic
moon roof, Power seat
system
45 AM140No circuit
SPARESpare fuse

BODY
478
PROTECTING YOUR VEHICLEFROM CORROSION
Proper care of your Lexus can help ensure long±term
corrosion prevention.
The most common causes of corrosion to your
vehicle are:

The accumulation of road salt, dirt and moisture in
hard±to±reach areas under the vehicle.

Chipping of paint or undercoating caused by minor
accidents or by stones and gravel.
The following conditions will cause or accelerate
corrosion of your vehicle, so it is important to keep
your vehicle, particularly the underside, as clean as
possible and to repair any damage to paint or
protective coatings as soon as possible.

The presence of road salt or dust control chemicals,
salt in the air near the sea coast, industrial air
pollution.

High humidity, especially at temperatures just above
freezing point.

Certain parts of your vehicle are wet or damp for an
extended period of time, even though other parts of
the vehicle are dry.

Components of the vehicle which are prevented from
quick±drying due to lack of proper ventilation are exposed to high temperature.

BODY
481
Plastic wheel ornaments:
The plastic wheel
ornaments are damaged easily by organic substances.
If any organic substances splashes an ornament, be
sure to wash it off with water and check if the ornament
is damaged.
CAUTION
Do not attach the heavily damaged plastic wheel
ornament. It may fly off the wheel and cause accidents
while the vehicle is moving.
Aluminum wheels: Use only a mild soap or neutral
detergent.
Urethane bumpers and side moldings: Wash
carefully. Do not scrub with abrasive cleaners. The
bumper and side molding faces are soft.
Road tar: Remove with turpentine or cleaners that are
marked safe for painted surfaces.
NOTICE
Do not use organic substances (gasoline, kerosene, benzine or strong solvents), which may
be toxic or cause damage.
3. Rinse thoroughly ± dried soap can cause streaking.
In hot weather you may need to rinse each section right
after you wash it. 4. To prevent water spots, dry the vehicle using a clean
soft cotton towel. Do not rub or press hard ± you might
scratch the paint.
Automatic car wash
Your vehicle may be washed in an automatic car wash,
but remember that the paint can be scratched by some
type of brushes, unfiltered washing water, or the
washing process itself. Scratching reduces paint
durability and gloss, especially on darker colors. The
manager of the car wash should be able to advise you
whether
the process is safe for the paint on your vehicle.

BODY
484

Dirt or sand adhered to the leather may damage
the treated surface and cause it to wear earlier.Remove dirt or sand using a vacuum cleaner.

If a stain should fail to come out with a neutraldetergent, apply a cleaner that does notcontain an organic solvent.

Never use organic substances such asbenzine, alcohol or gasoline, or alkaline or acid
solutions for cleaning the leather as these could cause discoloring.

Use of a nylon brush or synthetic fiber cloth,etc. may scratch the fine grained surface of the
leather.

Mildew may develop on soiled leather upholstery. Be especially careful to avoid oil
spots. Try to keep your upholstery alwaysclean.

Long exposure to direct sunlight may causethe leather surface to harden and shrink. Keepyour vehicle in a shaded area, especially in thesummer.

The interior of your vehicle is apt to heat up onhot summer days, so avoid placing on theupholstery items made of vinyl or plastic orcontaining wax as these tend to stick to leather
when warm.

Improper cleaning of the leather upholstery could result in discoloration or staining.
Synthetic Leather Areas (Dash)
The synthetic leather areas may be easily cleaned
with a mild soap or detergent and water.
First vacuum over the upholstery to remove loose dirt.
Then, using a sponge or soft cloth, apply the soap
solution to the synthetic leather. After allowing it to soak
in for a few minutes to loosen the dirt, remove the dirt and
wipe off the soap with a clean damp cloth. If all the dirt
does not come off, repeat the procedure. Commercial
foaming±type cleaners are also available which work
well. Follow the manufacturer's instructions.
NOTICE
Do not use solvent, thinner, gasoline or windowcleaner on the interior.
Carpets, Windows and Seat Belts
Begin by vacuuming thoroughly to remove as much dirt
as possible. Several types of foam cleaners are
available; some are in aerosol cans and others are
powders or liquids which you mix with water to produce
a foam. To shampoo the carpets, use a sponge or brush
to apply the foam. Rub in overlapping circles. Do not
apply water ± the best results are obtained by keeping
the carpet as dry as possible. Read the shampoo
instructions and follow them closely.
The seat belts may be cleaned with mild soap and