engine lexus LS400 1995 Gauges, Meters and Service Reminder Indicators / 1995 LS400: STARTING AND DRIVING

SECTION 3 – 1
125
STARTING AND DRIVING
Starting and driving
Three−way catalytic converter126 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine exhaust caution 127. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before starting the engine128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition switch with steering lock128 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking brake129 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to start the engine130 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic transmission131 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cruise control136 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronically modulated air suspension139 . . . . . . . . . . . . . . . . . . . . .
Traction control system141 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake system142 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Types of tires145 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

STARTING AND DRIVING
126
THREE−WAY CATALYTIC
CONVERTER
Three−way catalytic converters are emission control
devices installed in the exhaust system.
The three−way catalytic converter located at the confluence of
exhaust pipes looks somewhat like a muffler, but its purpose
is to reduce pollutants in the exhaust gas.
CAUTION

Keep people and combustible materials away from
the exhaust pipe while the engine is running. The
exhaust gas is very hot.

Do not drive, idle or park your vehicle over anything
that might burn easily such as grass, leaves, paper or
rags.
NOTICE
A large amount of unburned gases flowing into the
three−way catalytic converter may cause it to overheat
and create a fire hazard. To prevent this and other
damage, observe the following precautions:

Use only unleaded gasoline.

Do not drive with an extremely low fuel level; running
out of fuel could cause the engine to misfire, creating
an excessive load on the three−way catalytic
converter.

Do not allow the engine to run at idle speed for more
than 20 minutes.

Avoid racing the engine.

Do not push−start or pull−start your vehicle.

Do not turn off the ignition while the vehicle is
moving.

Keep your engine in good running order.
Malfunctions in the engine electrical system,
electronic ignition system / distributor ignition
system or fuel system could cause an extremely high
three−way catalytic converter temperature.

If the engine becomes difficult to start or stalls
frequently, take your vehicle in for a check−up as
soon as possible. Remember, your Lexus dealer
knows your vehicle and its three−way catalytic
converter system best.

STARTING AND DRIVING
127

To ensure that the three−way catalytic converter and
the entire emission control system operate properly,
your vehicle must receive the periodic inspections
required by the Lexus Maintenance Schedule.
ENGINE EXHAUST CAUTION
CAUTION

Avoid inhaling the engine exhaust. It contains carbon
monoxide, which is a colorless and odorless gas. It
can cause unconsciousness or even death.

Make sure the exhaust system has no holes or loose
connections. The system should be checked from
time to time. If you hit something, or notice a change
in the sound of the exhaust, have the system checked
immediately.

Do not run the engine in a garage or enclosed area
except for the time needed to drive the vehicle in or
out. The exhaust gases cannot escape, making this
a particularly dangerous situation.

Do not remain for a long time in a parked vehicle with
the engine running. If it is unavoidable, however, do
so only in an unconfined area and adjust the heating
or cooling system to force outside air into the vehicle.

Keep the trunk lid closed while driving. An open or
unsealed trunk lid may cause exhaust gases to be
drawn into the vehicle. If you must drive with the
trunk lid open to accommodate a large object, close
the windows, open all the dashboard vents and have
the heating or cooling system deliver fresh air into
the vehicle by turning the fan to high speed with the
air intake control button in the OUTSIDE AIR mode.

To allow proper operation of your vehicle’s
ventilation system, keep the inlet grilles in front of the
windshield clear of snow, leaves, or other
obstructions.

If you smell exhaust fumes in the vehicle, drive with
the windows open and the trunk lid closed. Have the
cause immediately located and corrected.

STARTING AND DRIVING
128
BEFORE STARTING THE ENGINE
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, head restraint height
and steering wheel angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder indicators
function when turning the key to “ON”, and check the fuel
gauge to see that you have sufficient fuel.
IGNITION SWITCH WITH STEERING
LOCK
“START” − Starter motor on. The key will return to the
“ON” position when released.
For starting tips, see page 130.
“ON” − Engine on and all accessories on.
This is the normal driving position.
NOTICE
Do not leave the key in the “ON” position if the engine
is not running. The battery will discharge and the
electronic ignition system / distributor ignition system
could be damaged.
“ACC” − Accessories such as the radio operate, but the
engine is off.

STARTING AND DRIVING
129 If you leave the key in the “ACC” or “LOCK” position and open
the driver’s door, a buzzer will remind you to remove the key.
“LOCK” − Engine is off and the steering wheel is locked.
The ignition key can be removed only at this position.
To turn the key from “ACC” to the “LOCK” position, you must
put the transmission selector lever in the “P” position.
When starting the engine, the key may seem stuck at the
“LOCK” position. To free it, first be sure the key is pushed all
the way in, and then rock the steering wheel slightly while
turning the key gently.
If, in an emergency, you must turn the engine off while the
vehicle is moving, turn the key only to “ACC”.
PARKING BRAKE
1
To set: Fully depress the parking brake pedal.
2
To release: Pull the parking brake release lever.
Before leaving your vehicle, firmly apply the parking brake.
CAUTION
Before driving, make sure the parking brake is fully
released and that the parking brake reminder light is off.

STARTING AND DRIVING
130
HOW TO START THE ENGINE
Before cranking
1. Apply the parking brake firmly.
2. Turn off unnecessary lights and accessories.
3. Put the selector lever in “P”. If you need to restart the engine
while the vehicle is moving, put the selector lever in “N”. A
starter safety device will prevent the starter from operating if
the selector lever is in any drive position.
4. Depress the brake pedal and hold it to the floor until you are
ready to drive off.
Starting the engine
Before starting the engine, be sure to follow the instructions in
“Before cranking”.
Normal starting procedure
The multiport fuel injection system / sequential multiport fuel
injection system in your engine automatically controls the
proper air−fuel mixture for starting. You can start a cold or hot
engine as follows:
1. With your foot off the accelerator pedal, crank the engine by
turning the key to “START”. Release it when the engine starts.
2. After the engine runs for about 10 seconds, you are ready
to drive.If the weather is below freezing, let the engine warm up for a
few minutes before driving. Do not leave the vehicle while the
engine is warming up.
If the engine stalls ...
Simply restart it, using the correct procedure given in normal
starting.
If the engine will not start
See “If your vehicle will not start” on page 160.
NOTICE

Do not crank for more than 15 seconds at a time. This
may overheat the starter and wiring systems.

Do not race a cold engine.

If the engine becomes difficult to start or stalls
frequently, have the engine checked immediately.

STARTING AND DRIVING
131
AUTOMATIC TRANSMISSION
Your automatic transmission has a shift lock system to
minimize the possibility of incorrect operation. This
means you can only shift out of “P” position when the
brake pedal is depressed with the ignition switch in “ON”
position. ()
The shift position is displayed on the instrument
cluster.
P:Parking, engine starting and key removal position
R:Reverse position
N:Neutral position
D:Normal driving position (Shifting into overdrive possible)
3:Position for engine braking (Shifting into overdrive not
possible)
2:Position for engine braking
L:Position for stronger engine braking than that in “2” position
Correct use of the automatic transmission is explained in
the following parts.
(a) Normal driving
(b) Using engine braking
(c) Backing up
(d) Parking
(e) Good driving practice
(f) If you cannot shift the selector lever
(g) If the “ECT PWR” indicator light flashes

STARTING AND DRIVING
132
(a) Normal driving
 1
“P” (Park) position 2
“N” (Neutral) position
1. Start the engine as instructed in “How to start the
engine” on page 130.
The transmission must be in “P” or “N”. The engine will not start
in any drive position even if the ignition key is turned to
“START”.
 1
Driving pattern selector switch
2
Normal position 3
Power position
2. Set the driving pattern selector switch to the NOMAL
position.
Your transmission has a driving pattern selector switch which
allows you to select either “NORM” or “PWR” to suit your
driving condition. For ordinary driving, Lexus recommends that
you use the NORMAL position to improve fuel economy.
3. For more powerful acceleration and sporty driving, use
the POWER position.
In the POWER position, the “ECT PWR” light in the instrument
cluster is on and the transmission is shifted up at higher vehicle
speeds and shifted down more responsively than in the
NORMAL position.

STARTING AND DRIVING
133
 1
“D” (Drive) position 2
Brake pedal
4. With your foot holding down the brake pedal, shift the
selector lever to “D”.
Always use the “D” position to improve fuel economy and quiet
driving. Only in this position, shifting into the overdrive gear is
possible. However, while the engine coolant temperature is
low, the transmission will not shift into the overdrive gear even
in the “D” position. (See “(b) Using engine braking” and “(e)
Good driving practice” for exceptions.)
CAUTION
Never put your foot on the accelerator pedal while
shifting.
5. Release the parking brake and brake pedal. Depress the
accelerator pedal slowly for smooth starting.
In normal cruising, the vehicle will start in the first gear and
automatically shift to the most suitable gear for the running
conditions.
In “3” position, the automatic transmission system will select
the most suitable gear for the running conditions such as hill
climbing, hard towing, etc.
If you need to accelerate rapidly while driving, depress the
accelerator pedal to the full throttle position. This provides
more acceleration by automatically downshifting the
transmission to the next lower gear or beyond, depending on
the vehicle speed.
If engine braking is needed, such as in descending a long hill,
see “(b) Using engine braking”.

STARTING AND DRIVING
134
(b) Using engine braking
To use the braking power of the engine, downshift the
transmission in the way described below:
1
Shift into the “3” position. The transmission will downshift
to the third gear.
2
Shift into the “2” position. The transmission will downshift
to the second gear when the vehicle speed is or becomes
lower than 134 km / h (83 mph) and more powerful engine
braking will be obtained.
3
Shift into the “L” position. The transmission will downshift
to the first gear when the vehicle speed is or becomes
lower than 73 km / h (45 mph) and maximum engine
braking will be applied.
CAUTION
Be careful when downshifting on a slippery surface. The
abrupt change in engine speed could cause the vehicle
to spin or skid.
NOTICE

Be careful not to overrev the engine. Watch the
tachometer to keep engine rpm from going into the
red zone. The approximate maximum allowable
speed for each position is given below for your
reference:
“2”... 134 km / h (83 mph)
“L”... 73 km / h (45 mph)

Do not continue hill climbing or hard towing for a long
time in the “2” or “L” position. This may cause severe
automatic transmission damage from overheating.
To prevent such damage, “3” position should be
used in hill climbing or hard towing.