evap LEXUS SC400 1991 Service Owner's Guide

(e) Connect the following connectors:(1) Throttle position sensor connector
(2) w/ TRAC:Sub±throttle position sensor connector
(3) w/ TRAC: Sub±throttle actuator connector
27. REINSTALL HEATER WATER VALVE
(a) Install the water valve and bracket assembly with the 2 bolts.
(b) Install the engine wire clamp with the bolt.
(c) Connect the VSV connector.
28. REINSTALL RH NO.3 TIMING BELT COVER
(a) Install the 3 gaskets to the timing belt cover.
(b) Fit the portion A of the timing belt cover, matching it with the lower high±tension cord cover.
(c) Install the timing belt cover with the 3 bolts.
29. REINSTALL VSV FOR EVAP SYSTEM Install the VSV with the 2 bolts.
30. REINSTALL LH NO.3 TIMING BELT COVER
(a) Install the 3 gaskets to the timing belt cover.
(b) Install the cord grommet to the high±tension cord (from the LH ignition coil).
(c) Install the cord grommet to the timing belt cover.
(d) Fit the portion A of the timing belt cover, matching it with the lower high±tension cord cover.
(e) Install the timing belt cover with the 4 bolts.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±29
WhereEverybodyKnowsYourName

(b) Push the front side of the upper high±tension cord cover, andfit the front side claw groove of the upper high±tension cord
cover to the claw of the lower high ±tension cord cover.
(c) Install the upper high±tension cord cover with the 2 bolts.
37. REINSTALL INTAKE AIR CONNECTOR
(a) Connect the end portions of the intake air connector to the throttle body and air cleaner hose.
(b) Tighten the 2 hose clamps
(c) Install the bolt holding the intake air connector to the cylinder head cover.
(d) Connect the following hoses: (1) Air hose to IAC valve
(2) Air hose (from air control valve on PS pump) to intake air
connector
38. RECONNECT CONTROL CABLES TO THROTTLE BODY Connect the following cables:
(1) Accelerator cable
(2) Transmission throttle control cable
(3) Cruise control actuator cable
39. REINSTALL THROTTLE BODY COVER
(a) Install the thro ttle body cover and hose clamp with the cap nut
and 2 bolts.
(b) Install the EVAP hose to the hose clamp.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±31
WhereEverybodyKnowsYourName

5. REMOVE RH ENGINE WIRE COVERRemove the bolt and engine wire cover.
6. REMOVE LH ENGINE WIRE COVER Remove the 2 bolts and engine wire cover.
7. REMOVE VSV FOR EVAP SYSTEM Remove the 2 bolts, and disconnect the VSV from the cylin-
der head cover and timing belt cover.
8. REMOVE RH NO.3 TIMING BELT COVER Remove the 3 bolts, timing belt cover and 3 gaskets.
9. REMOVE LH NO.3 TIMING BELT COVER
(a) Remove the 4 bolts
(b) Disconnect the cord grommet from the timing belt cover, and remove the timing belt cover and 3 gaskets.
(c) Remove the cord grommet from the high±tension cord.
EG±38
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

19. RECONNECT LH CAMSHAFT POSITION SENSORCONNECTOR
20. RECONNECT COLD START INJECTOR CONNECTOR
21. REINSTALL RH NO.3 TIMING BELT COVER
(a) Install the 3 gaskets to the timing belt cover.
(b) Fit the portion A of the timing belt cover, matching it with the lower high±tension cord cover.
(c) Install the timing belt cover with the 3 bolts.
22. REINSTALL VSV FOR EVAP SYSTEM Install the VSV with the 2 bolts.
23. REINSTALL LH NO.3 TIMING BELT COVER
(a) Install the 3 gaskets to the timing belt cover.
(b) Install the cord grommet to the high±tension cord (from the LH ignition coil).
(c) Install the cord grommet to the timing belt cover.
(d) Fit the portion A of the timing belt cover, matching it with the lower high±tension cord cover.
(e) Install the timing belt cover with the 4 bolts.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±41
WhereEverybodyKnowsYourName

30. INSTALL VSV FOR EVAP SYSTEMInstall the VSV with the 2 bolts.
31. INSTALL LH NO.3 TIMING BELT COVER
(a) Install the 3 gaskets to the timing belt cover.
(b) Install the cord grommet to the high±tension cord (from the LH ignition coil).
(c) Install the cord grommet to the timing belt cover.
(d) Fit the portion A of the timing belt cover, matching it with the lower high±tension cord cover.
(e) Install the timing belt cover with the 4 bolts.
32. INSTALL RH ENGINE WIRE COVER
(a) Fit portions A and B of the engine wire cover, matching them with the lower high±tension cord cover and No.3 timing belt
cover.
(b) Install the timing belt cover with the bolt.
33. INSTALL LH ENGINE WIRE COVER
(a) Connect portions A and B of the engine wire cover to the wire
brackets.
(b) Set the VSV (for the fuel pressure) wire in original position.
(c) Fit portions C and D of the engine wire cover, matching them with the lower high±tension cord cover and No.3 timing belt
cover.
(d) Install the timing belt cover with the 2 bolts.
34. INSTALL UPPER HIGH±TENSION CORD COVER
(a) Fit portion A of the upper high±tension cord cover matching the top of the lower high±tension cord cover.
EG±68
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

(b) Remove the nut and 3 bolts, and disconnect the PS pumpfrom the engine.
5. REMOVE TWC (FRONT)
(a) Remove the 4 bolts holding the pipe support bracket to the transmission.
(b) Remove the 4 bolts and nuts holding the front exhaust pipe to the TWC, and remove the pipe support bracket.
(c) Disconnect the front exhaust pipe from the TWC, and remove
the 2 gaskets.
(d) Using a 14 mm deep socket wrench, remove the 3 nuts, TWC
and gasket. Remove the 2 TWC.
6. REMOVE THROTTLE BODY COVER
(a) Disconnect the EVAP hose from the hose clamp.
(b) Remove the cap nut.
(c) Loosen the 2 bolts, and remove the hose clamp and throttle body cover.
7. DISCONNECT CONTROL CABLES FROM THROTTLE BODY
Disconnect the following cables:
(1) Accelerator cable
(2) Transmission throttle control cable
(3) Cruise control actuator cable
8. REMOVE RH IGNITION COIL
(a) Disconnect the ignition coil connector.
(b) Remove the 2 bolts and ignition coil.
EG±76
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

9. REMOVE WATER INLET AND INLET HOUSING
(a) Disconnect the water bypass hose from the IAC valve.
(b) Remove the 2 bolts holding the water inlet housing to waterpump.
(c) Pull out the water inlet and inlet housing assembly.
(d) Remove the O±ring from the water inlet housing.
10. REMOVE TIMING BELT REAR PLATES
Remove the 2 bolts and rear plate. Remove the 2 rear plates.
11. REMOVE VACUUM PIPE
(a) Disconnect the following hoses: (1) California:
Vacuum hose from throttle body
(2) Except California: 3 vacuum hoses from throttle body
(3) Vacuum hose from fuel pressure regulator
(4) 2 vacuum hoses from VSV for fuel pressure control
(5) Except California:
2 vacuum hoses from EGR vacuum modulator
(6) 2 vacuum hoses (from VSV for EVAP) from vacuum pipe
(7) Vacuum hose (from VSV for fuel pressure) from air in-
take chamber
(8) Vacuum hose (from charcoal canister) from vacuum pipe
±
1UZ±FE ENGINE ENGINE MECHANICALEG±77
WhereEverybodyKnowsYourName

(c) Connect the following hoses:(1) Water bypass hose to IAC valve
(2) Water bypass hose to water bypass pipe(from rear water bypass joint)
(3) 2 vacuum hoses to VSV for EGR
(d) Install the hose clamp to the PCV hose.
35. INSTALL VACUUM PIPE
(a) Install the vacuum pipe, vacuum hose assembly and EGR water bypass pipe (California) with the 2 bolts.
(b) Connect the following hoses: (1) California: Vacuum hose to throttle body
(2) Except California: 3 vacuum hoses to throttle body
(3) Vacuum hose to fuel pressure regulator
(4) 2 vacuum hoses to VSV for fuel pressure control
(5) Except California: 2 vacuum hoses to EGR vacuum modulator
(6) 2 vacuum hoses (from VSV for EVAP) to vacuum pipe
(7) Vacuum hose (from VSV for fuel pressure) to air intake chamber
(8) Vacuum hose (from charcoal canister) to vacuum pipe
EG±132
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

(g) Connect the water bypass hose to the IAC valve.
38. INSTALL RH IGNITION COIL
(a) Install the ignition coil with the 2 bolts.
(b) Connect the ignition coil connector.
39. CONNECT CONTROL CABLES TO THROTTLE BODYConnect the following cables:
(1) Accelerator cable
(2) Transmission throttle control cable
(3) Cruise control actuator cable
40. INSTALL THROTTLE BODY COVER
(a) Install the thro ttle body cover and hose clamp with the cap nut
and 2 bolts.
(b) Install the EVAP hose to the hose clamp.
41. INSTALL POWER STEERING (PS) PUMP
(a) Install the PS pump with the nut and 3 bolts. Alternately tighten the bolts and nut.
Torque:
39 NVm (400 kgf Vcm, 29 ft Vlbf) for bolt
43 N Vm (440 kgf Vcm, 32 ft Vlbf) for nut
EG±134±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

7. REMOVE THROTTLE BODY COVER
(a) Disconnect the EVAP hose from the hose clamp.
(b) Remove the cap nut.
(c) Loosen the 2 bolts, and remove the hose clamp and throttlebody cover.
8. DISCONNECT CONTROL CABLES TO THROTTLE BODY Disconnect the following cables:
(1) Accelerator cable
(2) Transmission throttle control cable
(3) Cruise control actuator cable
9. REMOVE AIR CLEANER
(a) Disconnect the VAF meter connector.
(b) Remove the hose clamp bolt holding the air cleaner hose to the intake air connector.
(c) Remove the 4 bolts.
(d) Disconnect the air cleaner hose from the intake air connector.
(e) Disconnect the air duct from the air cleaner case, and remove
the air cleaner.
10. D I S C O N N E C T VA CUUM HOSE (A) (FROM PS AIR
CONTROL VALVE) FROM AIR INTAKE CHAMBER
11. REMOVE INTAKE AIR CONNECTOR
(a) Disconnect the following hoses from the intake air connector:
(1) Air hose (from IAC valve)
(2) Air hose (from air control valve on PS pump)
(b) Remove the hose clamp bolt holding the intake air connector to the throttle body.
(c) Remove the bolt and intake air connector.
EG±140
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName