heating MAZDA MODEL CX-3 2015 Owners Manual (in English)

3–27
Before Driving
Fuel and Emission
Engine Exhaust (Carbon monoxide)
WARNING
Do not drive your vehicle if you smell exhaust gas inside the vehicle:
Engine exhaust gas is dangerous. This gas contains carbon monoxide (CO), which is
colourless, odourless, and poisonous. When inhaled, it can cause loss of consciousness
and death. If you smell exhaust gas inside the vehicle, keep all windows fully open and
contact an expert repairer, we recommend an Authorised Mazda Repairer immediately.
Do not run the engine when inside an enclosed area:
Running the engine inside an enclosed area, such as a garage, is dangerous. Exhaust
gas, which contains poisonous carbon monoxide, could easily enter the cabin. Loss of
consciousness or even death could occur.
Open the windows or adjust the heating or cooling system to draw fresh air when idling
the engine:
Exhaust gas is dangerous. When the vehicle is stopped with the windows closed and
the engine running for a long time even in an open area, exhaust gas, which contains
poisonous carbon monoxide, could enter the cabin. Loss of consciousness or even death
could occur.
Clear snow from underneath and around your vehicle, particularly the tail pipe, before
starting the engine:
Running the engine when a vehicle is stopped in deep snow is dangerous. The exhaust
pipe could be blocked by the snow, allowing exhaust gas to enter the cabin. Because
exhaust gas contains poisonous carbon monoxide, it could cause loss of consciousness
or even death to occupants in the cabin.
$9@&;&&%@&EJUJPOJOEC







3–49
Before Driving
Driving Tips
Rocking the Vehicle
WARNING
Do not spin the wheels at high speed,
and do not allow anyone to stand
behind a wheel when pushing the
vehicle:
When the vehicle is stuck, spinning
the wheels at high speed is dangerous.
The spinning tyre could overheat and
explode. This could cause serious
injuries.
CAUTION
Too much rocking may cause engine
overheating, transaxle failure, and tyre
damage.
If you must rock the vehicle to free it from
snow, sand or mud, depress the accelerator
slightly and slowly move the shift lever
from 1 (D) to R.
Winter Driving
Carry emergency gear, including tyre
chains, window scraper, fl ares, a small
shovel, jumper leads, and a small bag of
sand or salt.
Ask an expert repairer, we recommend an
Authorised Mazda Repairer to check the
following:
 


 Have the proper ratio of antifreeze in the
radiator.
  Refer to Engine Coolant on page 6-29 .



 Inspect the battery and its leads. Cold
reduces battery capacity.
 


 Use an engine oil appropriate for the
lowest ambient temperatures that the
vehicle will be driven in (page 6-23 ).
 


 Inspect the ignition system for damage
and loose connections.
 


 Use washer fl uid made with antifreeze—
but do not use engine coolant antifreeze
for washer fl uid (page 6-32 ).
$9@&;&&%@&EJUJPOJOEC







3–61
Before Driving
Towing
 


 When ascending a hill, shift into a lower gear to reduce the possibility of overloading or
overheating the engine, or both.
 


 When descending a hill, shift into a lower gear and use engine compression as a braking
effect. Pay constant attention to speed and use the brakes only as needed. Holding the
brake pedal down for a prolonged period may cause the brakes to overheat and lose
power.
Parking
Avoid parking on an incline with a trailer. If this must be done, follow these instructions.
Parking on an Incline
1. Set the parking brake and the brakes.
2. Have someone block the wheels of the vehicle and trailer while you apply the brakes.
3. After the wheels are blocked, release the parking brake and the brakes slowly, allowing
the blocks to bear the load.
4. Set the parking brake fi rmly.
5. If the vehicle has an automatic transaxle, put the selector lever in P. If it has a manual
transaxle, place the gear shift in 1 or R.
Starting on an Incline
1. Start the engine (page 4-5 ).
2. Release the parking brake and slowly pull away a short distance from the wheel blocks.
3. Stop on the nearest level ground, set the parking brake, and pick up the wheel blocks.
$9@&;&&%@&EJUJPOJOEC







4–57
When Driving
Transaxle
Driving Tips
WARNING
Do not let the vehicle move in a
direction opposite to the direction
selected by the selector lever:
Do not let the vehicle move backward
with the selector lever in a forward
position, or do not let the vehicle move
forward with the selector lever in the
reverse position. Otherwise, the engine
may stop, causing the loss of the power
brake and power steering functions,
and make it diffi cult to control the
vehicle which could result in an
accident.
Passing
For extra power when passing another
vehicle or climbing steep grades, depress
the accelerator fully. The transaxle will
shift to a lower gear, depending on vehicle
speed.
NOTE
(Some models)
The accelerator pedal may initially feel
heavy as it is being depressed, then feel
lighter as it is depressed further. This
change in pedal force aids the engine
control system in determining how
much the accelerator pedal has been
depressed for performing kickdown,
and functions to control whether or not
kickdown should be performed.
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:
1. Depress the brake pedal.
2. Shift to D or M1, depending on the
load weight and grade steepness.
3. Release the brake pedal while gradually
accelerating.
Descending steep grades
When descending a steep grade, shift to
lower gears, depending on load weight and
grade steepness. Descend slowly, using the
brakes only occasionally to prevent them
from overheating.
$9@&;&&%@&EJUJPOJOEC







4–69
When Driving
Switches and Controls
NOTE
Because heavy ice and snow can jam
the wiper blades, the wiper motor is
protected from motor breakdown,
overheating and possible fi re by a
circuit breaker. This mechanism will
automatically stop operation of the
blades, but only for about 5 minutes.
If this happens, turn off the wiper switch
and park off the right-of-way, and
remove the snow and ice.
After 5 minutes, turn on the switch and
the blades should operate normally. If
they do not resume functioning, consult
an expert repairer, we recommend an
Authorised Mazda Repairer as soon as
possible. Drive to the side of the road
and park off the right-of-way. Wait until
the weather clears before trying to drive
with the wipers inoperative.
Windscreen Wipers
Turn the wipers on by pressing the lever
up or down.
With intermittent wiper
Switch Position
Wiper operation
No. Type A Type B
Single wipe cycle (mist)
Stop
Intermittent
Low speed
High speed
Variable-speed intermittent wipers
Set the lever to the intermittent position
and choose the interval timing by rotating
the ring.
INT ring
$9@&;&&%@&EJUJPOJOEC







*Some models.4–95
When Driving
4WD
4-Wheel Drive (4WD)
Operation
*
4WD provides excellent drivability on
snow-covered and ice-packed roads, sand
and mud, as well as on steep slopes and
other slippery surfaces.
A system malfunction or operation
conditions are indicated by a warning.
Refer to Warning/Indicator Lights on page
4-37 .
WARNING
Never spin a wheel that is off the
ground:
Spinning a wheel that is off the ground
as a result of the vehicle being stuck
or in a ditch is dangerous. The drive
assembly could be seriously damaged
which could lead to an accident or
could even lead to overheating, oil
leakage, and a fi re.
4WD Driving
This vehicle has not been designed for the
purpose of off-road driving or rallies. Do
not attempt to drive over uneven or rocky
surfaces, or across rivers.
Although this vehicle is equipped with
4WD, acceleration, steering and braking
operations should be conducted in the
same manner as with a non-4WD vehicle,
with the emphasis placed on safe driving.
Tyres and Tyre Chains
The condition of the tyres plays a large
role in the performance of the vehicle.
Moreover, to prevent adverse effects to the
drive assembly, please note the following:
T y r e s
 




 When replacing tyres, always replace all
front and rear tyres at the same time.
 


 All tyres must be of the same size,
manufacture, brand and tread pattern.
Pay particular attention when equipping
snow or other types of winter tyres.
 


 Do not mix tread-worn tyres with
normal tyres.
 


(With tyre pressure monitoring
system)
  Inspect tyre infl ation pressures at the
specifi ed periods adjust to the specifi ed
pressures, and initialize the tyre pressure
monitoring system.
NOTE
Check the tyre infl ation pressure label
attached to driver's door frame for the
correct tyre infl ation pressure.




 Make sure to equip the vehicle with
genuine wheels of the specifi ed size,
on all wheels. With 4WD, the system is
calibrated for all four wheels being of
the same dimensions.
$9@&;&&%@&EJUJPOJOEC







5–7
Interior Features
Air-Conditioning System
Recirculated air position ()
Outside air is shut off. Air within the
vehicle is recirculated.
Outside air position (
)
Outside air is taken into the vehicle. Use
this position for normal ventilation and
heating.
WARNING
Do not use the position in cold or
rainy weather:
Using the
position in cold or rainy
weather is dangerous as it will cause
the windows to fog up. Your vision will
be hampered, which could lead to a
serious accident.
Heating
1. Set the mode selector dial to the
position.
2. (Type A)
Set the air intake selector to the outside
air position.
(Type B)
Set the air intake selector to the
position.
3. Set the temperature control dial to the
hot position.
4. Set the fan control dial to the desired
speed.
5. If dehumidifi ed heating is desired, turn
on the air conditioner.
NOTE
  If the windscreen fogs up easily, set
the mode selector dial to the
position.  If cooler air is desired at face level,
set the mode selector dial to the
position and adjust the temperature
control dial to maintain maximum
comfort.
  The air to the fl oor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
Cooling (With air conditioner)
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
cold position.
3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner by pressing
the A/C switch.
5. After cooling begins, adjust the fan
control dial and temperature control
dial as needed to maintain maximum
comfort.
CAUTION
If the air conditioner is used while
driving up long hills or in heavy traffi c,
monitor the engine coolant temperature
warning light to see if it is illuminated or
fl ashing (page 4-36 ).
The air conditioner may cause engine
overheating. If the warning light is
illuminated or fl ashing, turn the air
conditioning off (page 7-29 ).
$9@&;&&%@&EJUJPOJOEC







5–8
Interior Features
Air-Conditioning System
NOTE
  When maximum cooling is desired,
set the temperature control dial to the
extreme cold position and set the air
intake selector to the recirculated air
position, then set the fan control dial
to position 4.
  If warmer air is desired at fl oor level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
  The air to the fl oor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
Ventilation
1. Set the mode selector dial to the
position.
2. (Type A)
Set the air intake selector to the outside
air position.
(Type B)
Set the air intake selector to the
position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.
Windscreen Defrosting and
Defogging
1. Set the mode selector dial to the
position.
2. (Type B)
Set the air intake selector to the
position.
3. Set the temperature control dial to the
desired position. 4. Set the fan control dial to the desired
speed.
5. If dehumidifi ed heating is desired, turn
on the air conditioner.
WARNING
Do not defog the windscreen using the
position with the temperature
control set to the cold position:
Using the
position with the
temperature control set to the cold
position is dangerous as it will cause
the outside of the windscreen to fog up.
Your vision will be hampered, which
could lead to a serious accident. Set the
temperature control to the hot or warm
position when using the
position.
NOTE
  For maximum defrosting, turn on the
air conditioner, set the temperature
control dial to the extreme hot
position, and the fan control dial to
position 4.
  If warm air is desired at the fl oor, set
the mode selector dial to the
position. (Type A)
 In the position, the outside air
position is automatically selected.
The air intake selector cannot be
changed to the recirculated air
position.
$9@&;&&%@&EJUJPOJOEC







*Some models.7–1
7If Trouble Arises
Helpful information on what to do if a problem arises with the vehicle.



Parking in an Emergency .................................................................. 7-2
Parking in an Emergency .............................................................. 7-2
Flat Tyre .............................................................................................. 7-3
Spare Tyre and Tool Storage ......................................................... 7-3
Emergency Flat Tyre Repair Kit
* ................................................ 7-10
Changing a Flat Tyre (With Spare Tyre) ..................................... 7-17
Battery Runs Out ............................................................................. 7-24
Jump-Starting .............................................................................. 7-24
Emergency Starting ......................................................................... 7-27
Starting a Flooded Engine (SKYACTIV-G 2.0 ) ........................ 7-27
Push-Starting ............................................................................... 7-27
Running Out of Fuel (SKYACTIV-D 1.5) .................................. 7-28
Overheating ...................................................................................... 7-29
Overheating ................................................................................. 7-29
Emergency Towing ........................................................................... 7-31
Towing Description ..................................................................... 7-31
Towing/Tiedown Hooks .............................................................. 7-32
Warning/Indicator Lights and Warning Sounds ........................... 7-35
If a Warning Light Turns On or Flashes...................................... 7-35
Message Indicated on Display
* ................................................... 7-48
Warning Sound is Activated ........................................................ 7-50
When Liftgate Cannot be Opened .................................................. 7-55
When Liftgate Cannot be Opened ............................................... 7-55
Active Driving Display Does Not Operate ..................................... 7-56
If the Active Driving Display does not operate .......................... 7-56
$9@&;&&%@&EJUJPOJOEC







7–15
If Trouble Arises
Flat Tyre
CAUTION
If the compressor operates slowly or
becomes hot, it indicates overheating.
Turn the compressor off immediately
and leave it turned off for 30 minutes or
longer.
NOTE
  Check the tyre infl ation pressure
label (driver's door frame) for the
correct tyre infl ation pressure.

 Do not use the compressor for longer
than 10 minutes because using the
compressor for long periods could
damage it.
  If the tyre does not infl ate, repair
of the tyre may not be possible. If
the tyre does not reach the correct
infl ation pressure within a 10-minute
period, it probably has received more
extensive damage.
 When this happens, the emergency
fl at tyre repair kit cannot be used
to repair the tyre. Contact an
expert repairer, we recommend an
Authorised Mazda Repairer.
  If the tyre has been over-infl ated,
loosen the screw cap on the
compressor and bleed some of the air
out.
18. When the tyre has been infl ated to
the proper infl ation pressure, turn the
compressor switch off and remove the
compressor hose from the tyre valve.
19. Install the tyre valve cap.
20. Put the emergency fl at tyre repair kit in
the luggage compartment and continue
driving.
CAUTION
  Drive carefully to an expert repairer,
we recommend an Authorised Mazda
Repairer and keep the vehicle speed
below 80 km/h (50 mph).
  If the vehicle is driven 80 km/h (50
mph) or higher, the vehicle might
begin to vibrate.
NOTE
(With tyre pressure monitoring
system)
If the tyre is not properly infl ated, the
tyre pressure monitoring system warning
light will illuminate.
21. After driving the vehicle for 10 minutes
or 5 km (3 miles), check the tyre
pressure with the tyre pressure gauge
equipped with the compressor. If the
tyre pressure has fallen below the
correct tyre pressure, infl ate the tyre to
the correct pressure again following the
steps from number 16.
$9@&;&&%@&EJUJPOJOEC