MERCEDES-BENZ A-CLASS HATCHBACK 2022 Owners Manual

=
The v ehicle as well as persons and objects are
located outside the range of movement of the
door. 
Press the programming button on the door
dr

ive unit.
Initiate the next step within approximately
30 seconds. 
Press previously programmed button 1, 2
or 3 r
epeatedly until the door closes.
When the door closes, programming is com-
pleted.
% Please also read the operating instructions for
t

he door drive.
Troubleshooting when programming the remote
contr
ol 
Check if the transmitter frequency of remote
contr

ol 5 is supported. 
Replace the batteries in remote control 5.
Hold remote control 5 at v
arious angles from
a distance of 1 cm to 8 cm front of the inside
rearview mirror. You should test every position
for at least 25 seconds before trying another
position. 
Hold remote control 5 at t
he same angles at
various distances in front of the inside rear
view mirror. You should test every position for
at least 25 seconds before trying another
position. 
On remote controls that transmit only for a
limit
ed period, press button 6 on remote
control 5 again before transmission ends. 
Angle the aerial line of the garage door opener
unit t
owards the remote control.
% It is possible that older garage doors cannot
be oper
ated using the remote control in the
inside rearview mirror even aser you have
successfully performed the measures descri-
bed above. If this is the case, contact the
HomeLink n
Hotline.
% Support and additional information on pro-
g

ramming:
= on the HomeLink n
Hotline on (0) 08000
466 354 65 or +49 (0) 6838 907-277
= on the Internet at https://
www.homelink.com Opening or closing the garage door
R

equirements:
= The corresponding button is programmed to
operate the door. 
Press and hold buttons 1, 2 or 3 until t
he
door opens or closes. 
If indicator lamp Oashes 4 y
ellow aser
approximately 20 seconds: press and hold the
previously pressed button again until the door
opens or closes.
Clearing the garage door opener memory 
Press and hold buttons 1 and 3.
Indicat
or lamp 4 lights up yellow. 
If indicator lamp 4 Oashes g
reen: release
buttons 1 and 3.
The entire memory has been deleted. 218
Driving and parking

Electric parking brake
Function of the electric parking brake (applying
aut omatically) &
WARNING Risk of accident and injur
y due
to leaving children unattended in the vehi-
cle
If children are les unatt
ended in the vehicle,
they could, in particular:
= open doors, thereby endangering other
persons or road users.
= get out and be struck by oncoming traPc.
= operate vehicle equipment and become
trapped, for example.
In addition, the children could also set the
vehicle in motion by, for example:
= releasing the parking brake.
= changing the transmission position.
= starting the vehicle. 
Never leave children unattended in the
v
ehicle. 
When leaving the vehicle, always take the
k
ey with you and lock the vehicle. 
Keep the vehicle key out of the reach of
c
hildren. Vehicles with manual transmission:
The electr

ic parking brake is applied if the vehicle
is brought to a standstill and one of the following
conditions is fulNlled:
= The vehicle has previously been driven at
speeds greater than 3 km/h.
= The vehicle is switched oM.
= The driver's door is opened.
% To prevent application: pull the handle of the
electr

ic parking brake ( page 221).
In the following situations, the electric parking
br
ake is also applied:
= The HOLD function is keeping the vehicle sta-
tionary.
= In addition, one of the following conditions
must be fulNlled:
- The vehicle is switched oM. -
The seat belt t
ongue is not inserted in the
seat belt buckle of the driver's seat and
the driver's door is opened.
- There is a system malfunction.
- The power supply is insuPcient.
- The vehicle is stationary for a lengthy
period.
When the electric parking brake is applied, the
red $ indicator lamp lights up in the instru-
ment cluster.
If the electric parking brake is not applied when
the driver's door is opened, the Risk of vehicle
rolling away Apply parking brake See Owner's
Manual message appears.
% The electric parking brake is not automatically
applied if t

he vehicle is switched oM by the
ECO start/stop function.
Vehicles with automatic transmission:
The electr

ic parking brake is applied if the trans-
mission is in position j and one of the following
conditions is fulNlled:
= The vehicle is switched oM. Driving and parking
219

=
The seat belt t ongue is not inserted in the seat
belt buckle of the driver's seat and the driver's
door is opened.
% To prevent application: pull the handle of the
electr

ic parking brake ( page 221).
In the following situations, the electric parking
br
ake is also applied:
= The HOLD function is keeping the vehicle sta-
tionary.
= Active Parking Assist is keeping the vehicle
stationary.
= Active Distance Assist DISTRONIC is bringing
the vehicle to a standstill.
= In addition, one of the following conditions
must be fulNlled:
- The vehicle is switched oM.
- The seat belt tongue is not inserted in the
seat belt buckle of the driver's seat and
the driver's door is opened.
- There is a system malfunction.
- The power supply is insuPcient. -
The v
ehicle is stationary for a lengthy
period.
When the electric parking brake is applied, the
red $ indicator lamp lights up in the instru-
ment cluster.
% The electric parking brake is not automatically
applied if t

he vehicle is switched oM by the
ECO start/stop function.
Function of the electric parking brake (releasing
aut
omatically)
The electric parking brake is released when the
following conditions are fulNlled:
= The driver's door is closed.
= The vehicle has been started.
= Vehicles with manual transmission: a gear has
been selected, you release the clutch pedal
and depress the accelerator pedal.
= You apply the brakes and shis from neutral i
into reverse gear k or a forward gear ( 1 -
6) when on level ground.
= Vehicles with automatic transmission: the
transmission is in position h or k and you depress the accelerator pedal or you
shis
fr
om transmission position j to h or k
when on level ground.
= If the transmission is in position k, the tail-
gate must be closed.
= The seat belt tongue is inserted into the seat
belt buckle of the driver's seat.
If the seat belt tongue is not inserted into the
seat belt buckle of the driver's seat, one of the
following conditions must be fulNlled:
- You shis from transmission position j.
or
- You have previously driven at speeds
greater than 3 km/h.
When the electric parking brake is released, the
red $ indicator lamp in the instrument cluster
goes out. 220
Driving and parking

Applying/releasing the electric parking brake
manuall
y
Applying 
Push handle 1.
The r
ed $ indicator lamp lights up in the
instrument cluster. %
The electric parking brake is only securely
applied if t

he red $ indicator lamp is lit
continuously.
Releasing 
Switch on the vehicle. 
Pull handle 1.
The r

ed $ indicator lamp in the instrument
cluster goes out.
Emergency braking 
Press and hold handle 1.
As long as t
he vehicle is in motion, the
Release parking brake message is displayed
and the red $ indicator lamp Oashes.
When the vehicle has been braked to a stand-
still, the electric parking brake is applied. The
red $ indicator lamp lights up in the instru-
ment cluster. Information on collision detection on a parked
v

ehicle If a collision is detected when the tow-away pro-
t
ection is primed on a locked vehicle, you will receive a
no
tiNcation in the multimedia system
when you switch the vehicle on.
You will receive information about the following
points:
= The area of the vehicle that may have been
damaged.
= The force of the impact.
The following situation can lead to inadvertent
activation:
= The parked vehicle is moved, forexample, in a
two-storey garage.
% Deactivate tow-away protection in order to
pr
event inadvertent activation. If you deacti-
vate tow-away protection, collision detection
will also be deactivated.
System limits
De
tection may be restricted in the following situa-
tions:
= the vehicle is damaged without impact,
forexample, if an outside mirror is torn oM or
the paint is damaged by a key
= an impact occurs at low speed Driving and parking
221

=
t he electric parking brake is not applied
% You are responsible for your vehicle. There-
f

ore, always make sure that your vehicle is
free of damage and is roadworthy. Notes on parking up the vehicle
If you leave the vehicle parked up for longer than
six w

eeks, it may suMer damage through disuse.
The 12 V battery may also be impaired or dam-
aged by heavy discharging.
Vehicles with automatic transmission: do not dis-
connect the 12 V battery even if the vehicle is les
idle for a lengthy period.
% Further information can be obtained at a
q

ualiNed specialist workshop. Standby mode (extension of the starter battery's
per
iod out of use) Standby mode function
% This function is not available for all models. If standby mode is activated, energy loss will be
minimised dur
ing extended periods of non-opera-
tion.
Standby mode is characterised by the following:
= The starter battery is preserved.
= The maximum non-operational time appears in
the media display.
= The connection to online services is interrup-
ted.
= The ATA (anti-thes alarm system) is not availa-
ble.
= The interior protection and tow-away protec-
tion functions are not available.
= The function for detecting collisions on a
parked vehicle is not available.
If the following conditions are fulNlled, standby
mode can be activated or deactivated using the
multimedia system:
= The vehicle is switched on.
= The vehicle has not been started.
Exceeding the vehicle's displayed non-operational
time may cause inconvenience; i.e. it cannot be guaranteed that the starter battery will reliably
s tart the vehicle.
Charge the starter battery in the following situa-
tions:
= The vehicle's non-operational time must be
extended.
= The Battery charge insufficient for standby
mode message appears in the media display.
% Standby mode is automatically deactivated
when t
he vehicle is switched on.
Activating/deactivating standby mode (parking up
t
he vehicle)
Requirements: = The vehicle is switched oM.
Multimedia system: 4 © 5
Settings 5
Vehicle 
Activate or deactivate Standby mode. 
Select Yes . 222
Driving and parking

Driving and driving safety systems
Driving systems and your responsibility
Your vehicle is equipped with driving systems
whic h assist you in driving, parking and manoeu-
vring the vehicle. The driving systems are only
aids. They are not a substitute for you paying
attention to your surroundings and do not relieve
you of your responsibility pertaining to road traPc
law. The driver is always responsible for maintain-
ing a safe distance to the vehicle in front, for vehi-
cle speed, for braking in good time and for staying
in lane. Pay attention to the traPc conditions at
all times and intervene when necessary. Be aware
of the limitations regarding the safe use of these
systems.
Driving systems can neither reduce the risk of
accident if you fail to adapt your driving style nor
override the laws of physics. They cannot always
take into account road, weather or traPc condi-
tions. Information on vehicle sensors and cameras
Some driving and driving safety systems use cam-
er
as as well as radar or ultrasonic sensors to
monitor the area in front of, behind or next to the
vehicle. 1
Multifunction camera
2 Cameras in the outside mirrors
3 Front radar 4
Front camera
5 Corner radars
6 Ultrasonic sensors
7 Reversing camera &
WARNING Risk of accident due t
o restric-
ted detection performance of vehicle sen-
sors and cameras
If the area around vehicle sensors or cameras
is co
vered, damaged or dirty, certain driving
and safety systems cannot function correctly.
There is a risk of an accident. 
Keep the area around vehicle sensors or
camer

as clear of any obstructions and
clean. 
Have damage to the bumper, radiator
g

rille or stone chipping in the area of the
front and rear windows repaired at a
qualiNed specialist workshop. Particularly, keep the areas around the sensors
and camer
as free of dirt, ice or slush
(  page 348). The sensors and cameras must Driving and parking
223

not be covered and the detection ranges around
t hem must be kept free. Do not attach additional
licence plate brackets, advertisements, stickers,
foils or foils to protect against stone chippings in
the detection range of the sensors and cameras.
Make sure that there are no overhanging loads
protruding into the detection range.
If there is damage to a bumper or the radiator
grille, or aser an impact, have the function of the
sensors checked at a qualiNed specialist work-
shop. Have damage or stone chipping in the area
of the cameras on the front and rear windows
repaired at a qualiNed specialist workshop. Overview of driving systems and driving safety
sy

stems =
ABS ( Anti-loc

k Braking System) ( page 225)
= BAS (B rake Assist System) (  page 225)
= ESP n
(Electronic Stability Program)
(  page 225)
= ESP n
Crosswind Assist ( page 226)
= ESP n
trailer stabilisation ( page 227) =
EBD (Electr
onic Brakeforce Distribution)
( page 227)
= STEER CONTROL ( page 228)
= HOLD function ( page 228)
= Hill Start Assist ( page 229)
= Adaptive Brake Lights ( page 230)
= Start-oM assist ( page 230)
= ATTENTION ASSIST ( page 230)
= Cruise control ( page 232)
= Limiter ( page 233)
= TraPc Sign Assist ( page 250)
= Speed Limit Assist (country-dependent)
(  page 249)
= Suspension with adaptive damping adjustment
( page 257)
Driving Assistance Package
The following functions are part of the Driving
Assistance Package. Certain functions are only
available in some countries. Some functions are
also available without the Driving Assistance
Package, albeit with restricted functionality. =
A ctive Distance Assist DISTRONIC
( page 235)
= Active Speed Limit Assist (country-dependent)
(  page 239)
= Route-based speed adaptation (country-
dependent) ( page 240)
= Active Brake Assist ( page 244)
= Active Steering Assist (country-dependent)
(  page 241)
= Active Emergency Stop Assist (country-
dependent) ( page 243)
= Blind Spot Assist and Active Blind Spot Assist
with exit warning ( page 252)
= Active Lane Keeping Assist ( page 255)
Parking Package
= Reversing camera (  page 258)
= 360° Camera (  page 260)
= Parking Assist PARKTRONIC (  page 264)
= Active Parking Assist (  page 268)224
Driving and parking

Functions of ABS
The Anti-lock Brake System (ABS) regulates the
br
ake pressure in critical driving situations:
= During braking, for instance, at maximum full-
stop braking or if there is insuPcient tyre trac-
tion, the wheels are prevented from locking.
= Vehicle steerability while braking is ensured.
If ABS intervenes when braking, you will feel a
pulsing in the brake pedal. The pulsating brake
pedal can be an indication of hazardous road con-
ditions and can serve as a reminder to take extra
care while driving.
System limits
= ABS is active from speeds of approx. 5 km/h.
= ABS may be impaired or may not function if a
malfunction has occurred and the yellow %
ABS warning lamp lights up continuously aser
the vehicle is started. Function of BAS
&
WARNING Risk of an accident caused b y a
malfunction in BAS (Brake Assist System)
If BAS is malfunctioning, the braking distance
in an emer
gency braking situation is
increased. 
Depress the brake pedal with full force in
emer

gency braking situations. ABS pre-
vents the wheels from locking. The Brake Assist System (BAS) supports your
emer
gency braking situation with additional brake
force.
If you depress the brake pedal quickly, BAS is
activated:
= BAS automatically boosts the brake pressure.
= BAS can shorten the braking distance.
= ABS prevents the wheels from locking.
The brakes will function as usual once you release
the brake pedal. BAS is deactivated. Functions of ESP
n &
WARNING Risk of skidding if ESP n
is
deactiv
ated
If you deactivate ESP n
, ESP n
canno
t carry out
vehicle stabilisation. 
ESP n
should onl
y be deactivated in the
following situations. *
NOTE Mer
cedes-AMG vehicles 
Observe the notes in the Supplement.
Y
ou could otherwise fail to recognise
dangers. The Electronic Stability Program (ESP
n
) can moni-
t
or and improve driving stability and traction in
the following situations within physical limits:
= When pulling away on wet or slippery carriage-
ways.
= When braking. Driving and parking
225

If the vehicle deviates from the direction desired
b y the driver, ESP n
can stabilise the vehicle by
intervening in the following ways:
= One or more wheels are braked.
= The engine output is adapted according to the
situation.
ESP n
is deactivated if the

=
The v ehicle is stabilised by means of individual
brake application on one side. Function of ESP
n
tr
ailer stabilisation &
WARNING Risk of accident in poor r
oad
and weather conditions
In poor road and weather conditions, the
tr
ailer stabilisation cannot prevent lurching of
the vehicle/trailer combination. Trailers with a
high centre of gravity may tip over before
ESP n
detects this. 
Always adapt your driving style to suit
t

he current road and weather conditions. When driving with a trailer, ESP
n
can s
tabilise
your vehicle if the trailer begins to swerve from
side to side:
= ESP n
trailer stabilisation is active above
speeds of 65 km/h.
= Slight swerving is reduced by means of a tar-
geted, individual brake application on one
side. =
In t
he event of severe swerving, the operating
energy output is also reduced and all wheels
are braked.
ESP n
trailer stabilisation may be impaired or may
not function if:
= The trailer is not connected correctly or is not
detected properly by the vehicle. Activating/deactivating ESP
n
(Electr
onic Stability
Program) Multimedia system:
4 © 5
Settings 5
Quick access
% ESPn
can onl
y be activated/deactivated using
quick access when at least one other function
is available in quick access. ESP n
can other-
wise be found in the Assistance menu.
* NOTE Mer
cedes-AMG vehicles 
Observe the notes in the Supplement.
Y
ou could otherwise fail to recognise
dangers. 
Select ESP. 
Select On or