display MERCEDES-BENZ C-CLASS COUPE 2015 Owners Manual

Visual and acousti
ccollision warning
If yo uswitch on the turn signal stochange lanes
and avehicl eisd etected in the sid emonitoring
range, yo ureceive avisua land acoustic collision
warning .You will then hea radoublewarning
tone and red warning lamp :flashes. If the turn
signal remains on, detected vehicles are indica-
ted by the flashing of red warning lamp :.
There are no further warning tones.
Course-correctin gbrake application
If Active Blind Spot Assist detects ariskofa side
impact in the monitoring range, acourse-cor-
recting brake application is carrie dout.T hisis
designed to hel pyou avoid acollision. G
WARNING
Ac ourse-correcting brake application cannot
always prevent acollision. There is ariskofan
accident.
Alway ssteer, brake or accelerate yourself,
especially if Active Blind Spot Assist warns
yo uorm akesac ourse-correcting brake appli-
cation. Alway smaintai nasafed istance at the
sides.
If ac ourse-correcting brake application occurs,
red warning lamp :flashe sinthe exterio rmir-
ror and adualw arning tone sounds. In addition,
display ;underlining the danger of asidec ol-
lisio nappea rs in the multifunctio ndisplay.
In very rar ecases, the system may make an
inappropriate brake application. Acourse-cor-
recting brake application may be interrupted at
any time if yo ustee rslightl yint he opposite
direction or accelerate.
The course-correcting brake application is avail-
able in the speed rang ebetween 30 km/h and
200 km/h.
Eithe racourse-correcting brake application
appropriate to the driving situation, or none at
all, may occu rif:
R ther eare vehicles or obstacles, e.g. crash
barriers ,onboth sides of your vehicle
R av ehicl eapproaches too closel yonthe side
R youh avea dopte das porty driving style with
high cornering speeds
R youc learl ybrake or accelerate
R ad riving safety system intervenes, such as
ESP ®
or PRE-SAFE ®
Brake R
ESP ®
is deactivated
R al ossoft yre pressure or adefective tyre is
detected
Activatin gActive Blind Spo tAssist
X Make sure tha tActive Blind Spot Assist is
activate dinthe on-board computer
(Y page 245).
X Turn the key to position 2in the ignition lock.
Warning lamps :in the exterio rmirrors light
up red for approximatel y1.5 seconds .Grey
radar waves propagating backwards appear
next to the vehicl einthe assistance display in
the multifunctio ndisplay.
Towin gatrailer
If yo ucoupl eupa trailer, make sure tha tyou
have correctly established the electrical con-
nection. Thi scan be accomplished by checking
the traile rlighting. Active Blind Spot Assist is
then deactivated. The radar waves next to the
vehicl eare hidden in the assistance display .The
Active Blind Spo tAssist not availa‐
Active Blind Spo tAssist not availa‐
ble ble when
when towing a
towing a trailer
trailerSee
SeeOwner's
Owner's
Manual
Manual message appears in the multifunction
display.
Active Lan eKeeping Assist General notes
Active Lane Keeping Assist monitors the are
ain
front of your vehicl ebymeans of multifunction
camera :at the top of the windscreen. Various
different areas to the front, rea rand sid eofyour
vehicl eare also monitore dwitht he ai doft he
radar sensor system .Active Lane Keeping
Assist detects lane marking sonthe roa dand
can warn yo ubefore yo uleave your lane unin-
tentionally .Ifyoudo not react to the warning ,a
lane-correcting application of the brakes can
bring the vehicl ebacki nto the original lane. Driving systems
223Driving and parking Z

Important safety notes
If you fail to adapt your driving style, Activ eLane
Keepin gAssist can neither reduce th eriskofan
acciden tnor override th elaws of physics .Active
Lan eKeepin gAssist canno ttak ea ccoun tof
road and weather conditions. It may no tdetect
traffic situations. Activ eLaneK eepin gAssist is
only an aid. You are responsible for th edistance
to th evehicle in front, for vehicle speed, for
braking in good tim eand for staying in lane.
Activ eLaneK eepin gAssist canno tcontin uously
keep your vehicle in its lane. G
WARNING
Activ eLaneK eepin gAssist canno talways
clearly detect lane markings.
In suc hcases, Activ eLaneK eepin gAssist
can:
R giv eanu nnecessar ywarning and then
mak eac ourse-correcting brak eapplication
to th evehicle
R neither giv eawarning no rintervene
Ther eisar iskofana ccident.
Always pay particula rattentio ntothetraffic
situation and keep within th elane ,especially
if Activ eLaneK eepin gAssist alert syou. Ter-
minate th einterventio ninanon-critical driv-
ing situation.
The system may be impaired or may no tfunction
if:
R there is poor visibility, e.g .due to insufficient
illumination of th eroad ,ord ue to snow, rain,
fog or spray
R there is glare, e.g .fro mo ncom ingt raffic, the
sun or reflectio nfromo ther vehicle s(e.g. if
th er oad surface is wet)
R thew indscree nisdirty, miste dup, damaged
or covered, for instance by asticker, in the
vicinity of th ecamera
R ther adar sensor sinthefron torr ear bumpers
or th eradiator trim are dirty, e.g .obscured by
snow
R no or several, unclear lane markings are pres-
en tfor on elane ,e.g.inac onstruction area
R thel ane markings are worn away, dark or cov-
ere dup, e.g .bydirt or snow
R thed istanc etothevehicle in fron tistoosmall
and th elane markings thus canno tbedetec-
ted R
thel ane markings chang equickly, e.g. lanes
branch off ,cross on eanother or merge
R ther oad is narrow and winding
R there are highly variable shad econdi tionson
th er oad
If no vehicle is detected in th eadjacent lane and
broke nlane markings are detected, no lane-cor-
rectin gbrak eapplication is made.
Warning vibration through th esteering
wheel
Aw arning may be given if afront wheel passes
ove ralane marking. It will warn you by mean sof
intermitten tvibration in th esteering wheel for
up to 1. 5seconds.
Lane-correcting brak eapplication
If you leave your lane under certain circumstan- ces ,the vehicle will brak ebriefly on on eside.
This is intended to help you return th evehicle to
th eo riginal lane. G
WARNING
Al ane-correcting brak eapplication cannot
always brin gthe vehicle back int othe original
lane .Ther eisar iskofana ccident.
Always steer ,brak eora ccelerate yourself,
especially if Activ eLaneK eepin gAssist warns
you or makes alane-correcting brak eappli-
cation. If
al ane-correcting brak eapplication occurs,
display :appear sinthemultifunction display.
The brak eapplication also slightly reduces driv-
ing speed.
This function is available in aspee drange
between 60 km/h and 20 0km/ h.
Al ane-correcting brak eapplication can be made
after driving ove ralane markin gdetected as
bein gsolid or broken. Before this, awarning 224
Driving systemsDriving and pa
rking

must have been issued by means of intermittent
vibration through the steering wheel. In addi-
tion, alane with lane markings on both sides
must be detected.
In the case of abroken lane marking being
detected, alane-correcting brake application
can only be made if avehicl ehas been detected
in the adjacent lane. Oncoming vehicles, over-
taking vehicles and vehicles in adjacent lanes
can be detected.
i Af
urther lane-correcting brake application
can only occur after yourv ehiclehas returned
to the original lane.
No lane-correcting brake application occurs if:
R you clearl yand activel ysteer, brake or accel-
erate
R you cut the corner on asharp bend
R you have switched on the turn signal
R ad riving safety system intervenes, such as
ESP ®
,P RE-SAFE ®
Brake or Active Blind Spot
Assist
R you have adopted asporty driving style with
high cornering speed sorhigh rates of accel-
eration
R ESP ®
is deactivated
R the transmission is not in position D
R on vehicles with atrailert ow hitch, the elec-
trical connection to the traile rhas been cor-
rectly established
R aloss of tyre pressure or adefective tyre has
been detected and displayed
R an obstacl einthe lane in which you are driving
has been detected
Active Lane Keeping Assist may not detect other
road users or traffic situations. An inappropriate
brake application may be interrupted at any time
if:
R you steer slightly in the opposite direction
R you switch on the turn signal
R you clearl ybrake or accelerate
Al ane-correcting brake application is interrup-
ted automatically if:
R ad riving safety system intervenes, such as
ESP ®
,P RE-SAFE ®
Brake or Active Blind Spot
Assist
R lane markings are no longer detected Activating/deactivatin
gActive Lane
Keeping Assist X
To activate: press button ;.
Indicator lamp :lights up. The Lane Keep‐ Lane Keep‐
ing
ing Assist
Assist on
onmessage appears in the mul-
tifunction display.Ifa ll conditions have been
satisfied, awarning or steering intervention
may be made.
If you drive at speed sabove 60 km/h and lane
markings are detected, the lines in the assis- tance graphic display (Y page 243) are
shown in green. Active Lane Keeping Assist is
read yfor use.
X To deactivate: press button;.
Indicator lamp :goes out. Active Lane Keep-
ing Assist is deactivated. The Lane
Lane Keeping Keeping
Assist off
Assist off message appears in the multi-
function display.
Selecting Standard or Adaptive setting X In the Assistance
Assistance menu on the on-board
computer, select the Active Lane Keep‐
Active Lane Keep‐
ing Assist
ing Assist function (Ypage 246).
X Select Standard
Standard orAdaptive
Adaptive.
When Standard
Standard is selected, no warning vibra-
tion occurs if:
R you have switched on the turn signals. In
this event, the warnings are suppressed for
ac ertain perio doftime.
R ad riving safety system intervenes, such as
ABS, BAS or ESP ®
.
When Adaptive
Adaptive is selected, no warning vibra-
tion occurs if:
R you have switched on the turn signals. In
this event, the warnings are suppressed for
ac ertain perio doftime.
R ad riving safety system intervenes, such as
ABS, BAS or ESP ®
.
R you accelerate hard, e.g. kickdown. Driving systems
225Driving and parking Z

the powe
routpu toft he engine ,and conse-
quentl ythe vehicle' sgradient-climbing capa-
bility, decrease with increasing altitude. Folding the bal
lcou plin ginoro ut
Folding ou tthe bal lcou pling G
WARNING
If the ball coupling is not correctl yengaged,
the trailer can detach .There is ariskofan
accident.
Alway sengag ethe ball coupling as described. G
WARNING
If yo urelease the ball coupling or it does not
engag ecorrectl ywhenf olding in, it will swing
out. Withi npivoting range of the ball coupling,
there is an increase driskofana ccident and
injury.
Onl yrelease the ball coupling if the pivoting
range is unobstructed .Alway smakes uret hat
the ball coupling engages when folding in.
Before yo ucan tow atrailer with your vehicle,
yo um ustfoldo utthe ball coupling.
X Make sure tha tthe vehicl eisstationary. X
Open the boot lid.
X Pull release knob :unti lthe ball coupling
unlocks.
The ball coupling folds ou tfro mu nder the rear
bumper.
The indicator lamp on the release knob
flashes. The trailer powe rsocket is integrated
in the ball coupling. X
Press the ball coupling in the directio nofthe
arrow unti litengages in avertica lposit ion.
Th eindicator lamp on the release knob goes
off.
Th em ultifunctio ndisplay shows the Check
Check
traile rhitch lock
traile rhitch lock displaymessage until
the ball coupling is engaged.
X Remov ethe protective coverin gfromt he ball
coupling and stor eitinasafep lace.
Folding in the bal lcou pling i
Fol
dthe ball coupling back in if yo uarenot
using the trailer tow hitch.
X Make sure tha tthe vehicl eisstationar yand
the trailer cable saredisconnected.
X Place the protective coverin gonthe ball cou-
pling.
X Pull release knob :agai nuntilthe ball cou-
pling unlocks.
Th eb allc oupling folds down fro munder the
rea rbum per. The indicator lamp on the
release knob flashes.
X Press the ball coupling unti litengages behind
the bumper.
Do not attempt to spee dupthisp roces sby
applying additional pressure with your foot.
Th es ystemc ould otherwis ebemechanically
damaged.
The indicator lamp on the release knob goes
ou ta nd the message in the multifunctio ndis-
play disappears. Couplin
gupatrailer
X Make sure tha tthe transmission is in position
P.
X Apply the electric parking brake. 228
Towin
gatrailerDriving an dparking

X
Position the trailer horizontally behind the
vehicle.
X Couple up the trailer.
X Establish the electrical connection between
the vehicle and the trailer.
X Check that the trailer lighting system is work-
ing.
X Push the combination switch upwards/down-
wards
X Check whether the corresponding turn signal
on the trailer is flashing.
Ac onnected trailer is only detected when the
electrical connection is established correctly
and when the lighting system is working prop- erly. The function of other systems, such as
ESP ®
,P ARKTRONIC, Active Parking Assist,
Active Blind Spot Assist or Lane Keeping
Assist also depends on this. Uncoupling
atrailer G
WARNING
If you uncouple atrailer with an engaged over-
run brake, you could trap your hand between
the vehicle and the trailer drawbar. This poses ar isk of injury.
Do not uncouple atrailer with an engaged
overrun brake. G
WARNING
Vehicles with level control:
If you disconnect the trailer cable, the vehicle is lowered. This can cause you or others to
become trapped between the vehicle body
and tyres, or underneat hthe vehicle. This
poses arisk of injury.
Make sure that no-one is in the immediate
vicinit yofthe wheel arch or underneat hthe
vehicle when disconnectin gthe trailer cable.
! Do not disconnect
atrailer with an engaged
overrun brake. Otherwise, your vehicle could
be damaged by the rebounding of the overrun
brake.
! Remove the installed adapter cable before
folding in the ball coupling. Otherwise, dam-
age may occur to the rear bumper and the
adapter cable. X
Make sure that the transmission is in position
P.
X Apply the electric parking brake.
X Secure the trailer against rolling away.
X Remove the trailer cable and decouple the
trailer. Trailer power supply
! You can connect accessories to the perma-
nent power supply up to amaximum of 240 W.
You cannot charge atrailer battery using the
power supply.
When it leaves the factory, your vehicle's trailer
socket is equipped with apermanen tpower
supply and apower supply that is switched on
via the ignition lock.
The permanen tpower supply is supplied via
trailer socket pin 9.
The power supply that is switched on via the
ignition lock is supplied via trailer socket pin 10.
The trailer's permanen tpower supply is
switched off in the event of low vehicle supply
voltage and after six hours at the latest.
You can find more information about fitting the
trailer electric sataqualified specialist work-
shop.
X To switch the connected power supply on
or off: turn the key to position 2or 0respec-
tively (Y page 145). Failure check for LEDs
If LED lamps are fitted in the trailer, amalfunc-
tion message may appear in the multifunction
display even if there is no fault. The reason for
the error message may be that the curren thas
fallen below the minimum of 50 mA.
To ensure reliable operation of the failure indi-
cator, each LED chain in the trailer lighting must
be guaranteed aminimum curren tof50mA. Trailer with 7-pin connector
General notes Trailer with 7-pin connector:
you can connect
to the 13-pin socket on the ball coupling using
an adapter or, if necessary, an adapter cable. Towing
atrailer
229Driving and parking Z

Important safety notes
G
WARNING
Operating th eintegrate dinformation systems
and communication sequipmen tinthevehicle
while driving will distrac tyou from traffic con-
ditions. You could then lose control of the
vehicle. Ther eisariskofana ccident.
Only operate these device sifroad traffic con-
dition spermit .Ifyou are unsure about the
surroundin gconditi ons, pull ove rtoasafe
location and mak eentrie sonlyw hile th evehi-
cle is stationary.
You must observ ethe legal requirements for the
country in whic hyou are currentl ydriving when
operating th eon-bo ard computer. G
WARNING
If th einstrumen tcluste rhas faile dormal-
functioned, you may no trecognise function
restriction srelevan ttosafety. The operating
safet yofy our vehicl emay be impaired .There
is ar iskofana ccident.
Drive on carefully. Hav ethe vehicl echecked
at aq ualified specialist workshop immedi-
ately.
If th eoperating safet yofyour vehicl eis
impaired ,park th evehicl esafely as soo naspos-
sible .Contac taqualified specialist workshop.
The on-board computer only shows message sor
warning sfromc ertai nsystems in th emultifunc-
tion display. You should therefor emakes ure
your vehicl eisoperating safely at all times.
Fo rano verview, see th einstrumen tcluste rillus-
tration (Y page 32). Display
sand operation Instrumen
tcluster lighting The lighting in th
einstrumen tcluster, in th edis-
plays and th econtrols in thevehicl einterior can
be adjusted usin gbrightness control knob :.
X Turn brightness control knob :up or down.
If you tur nthe ligh tswitch (Y page 118) to the
T, ÃorL position ,the brightness
will depend upon th ebrightness of th eambi-
en tlight.
i The ligh
tsensor in th einstrumen tcluster
automatically control sthe brightness of the
multifunction display.
In daylight, th edisplays in th einstrument
cluste rare lit .Adimming function is no tpos-
sible in daylight. Speedometer with segments
The speedometer is divided int osegments on
Mercedes-AM Gvehicles or vehicles with
DISTRONI CPLUS.
The segments in th espeedometer indicate
whic hspee drange is available.
R Cruis econtro lactivated (Y page 180):
The segments ligh tupfromt hestore dspeed
to th etype-tested maximum speed.
R Variable SPEEDTRONI Cactivated
(Y page 182):
The segments ligh tupfromt hestart of the
scale to th eselected limi tspeed.
R DISTRONI CPLUSa ctivated (Y page 184):
On eort wo segments in th eset spee drange
ligh tup.
R DISTRONI CPLUSd etects avehicl einf ront
moving mor eslowly than th estoreds peed: 232
Display
sand operationOn-boar dcomputer and displays

The segment
sbetween the speed of the vehi-
cle in front and the stored speed light up. Rev counter
! Do not drive in the overrevving range. Doing
so will damage the engine.
The red band in the rev counter indicates the
engine's overrevving range.
The fuel supply is interrupted to protec tthe
engine when the red band is reached. Outside temperature display
You should pay special attention to road condi-
tions when temperatures are around freezing
point.
Bear in mind that the outside temperature dis-
play indicates the measured air temperature
and not the road surface temperature.
The outside temperature display is in the multi-
function display (Y page 234).
Changes in the outside temperature are dis-
played after ashort delay. Coolant temperature gauge
G
WARNING
If you open the bonnet while the engine is
overheatin gorwhile there is afire in the
engine compartment,y ou could come into
contact with hot gases or other leaking ser-
vice products. There is adanger of injury.
Allow an overheatin gengine to cool down
before opening the bonnet .Ifthere is afire in
the engine compartment,l eave the bonnet
closed and notify the fire brigade.
The multifunction display shows the coolant
temperature gauge in the lower section of the
rev counter (Y page 32).
At high outside temperatures and when driving
uphill, the coolant temperature may rise to the
end of the scale.
Under normal operating conditions and with the
specified coolant level, the coolant temperature may rise to 120 †. Operating the on-board computer
:
Multifunction display
; Right control panel
= Left control panel
X To activat ethe on-board computer: turn
the key to position 1in the ignition lock.
Vehicles with manual transmission: if you
remove the key, then quickly re-insert it and turn
to position 1,the instrument cluster and, as a
result, the on-board computer as well, are not
activated.
You can control the multifunction display and
the settings in the on-board computer using the button sonthe multifunction steerin gwheel.
Left control panel ò R
Opens the menu list 9
: Press briefly:
R Scrolls through lists
R Select samenu or function
R In the Radio Radio orMedia
Media menu:
opens the track or station list and
selects astation ,anaudio track or
av ideo scene
R In the Telephone Telephone menu: switches
to the phone book and selects a
name or atelephone number Displays and operation
233On-board computer and displays Z

9
: Press and hold:
R
Scrolls quickly through all lists
R In the Radio Radio orMedia Media menu:
selects astation, audio track or
video scene using rapid scrolling
R In the Telephone
Telephone menu: starts
rapid scrolling if the phone book is open a R
In all menus: confirmst he selected
entryint he list
R In the Radio
Radio orMedia
Media menu:
opens the list of available radio
sources or media
R In the Telephone Telephone menu: switches
to the phone book and starts dial-
ling the selected number ñ R
Vehicles with Audio 20:
Switches off voice-operated con-
trol for navigation (see manufac-
turer's operating instructions)
R Vehicles with COMAND Online:
Switches off LINGUATRONIC (see
the separate operating instruc-
tions) % Press briefly:
R Back
R In the Radio Radio orMedia
Media menu: dese-
lects the track or station list or list
of available radio sources or media
R Hides display messages
R Exitst he telephone book/redial
memory % Press and hold:
R
Callsupt he standard display in the
Trip Trip menu Right control panel
~ R
Rejects or ends acall
R Exitst he telephone book/redial
memory 6 R
Makes or accepts acall
R Switches to the redial memory W
X R
Adjusts the volume 8 R
Mute ó R
Vehicles with Audio 20:
Switches on voice-operated con-
trol for navigation (see manufac-
turer's operating instructions)
R Vehicles with COMAND Online:
Switches on LINGUATRONIC (see
the separate operating instruc-
tions) Multifunction display
Multifunction display (example: vehicles with auto-
matic transmission)
: Drive program (Y page 159)
; Transmission position (Y page 160)
= Additional speedometer (Y page 248)
? Display
A Time
B Outside temperature
Display panel ?shows the selected menu or
submenu and display messages.
X To open the menu list: press theòbut-
ton on the steering wheel.
Display panel ?appears in the menu list.
Possible displays in the multifunction dis-
play:
R ZGearshift recommendation for manual
transmission (Y page 157) or for automatic234
Displays and operationOn-board computer and displays

transmission (shiftin
gmanually)
(Y page 163)
R j Activ eParking Assist (Y page 201)
R ¯ Cruise contro l(Ypage 180)
R È SPEEDTRONIC (Y page 182)
R _ Adaptive Highbea mAssist Plus
(Y page 121)
R è ECO start/sto pfunctio n(Ypage 149)
R ë HOLD functio n(Ypage 192)
R a DISTRONI CPLUSS teerin gAssist and
Stop&Go Pilo t(Y page 191)
R 120 km/h! 120 km/h! Maximum permissibl espeed
exceeded (only for certain countries) Head-up display
General notes The head-up displa
yprojects information from
the navigation syste mand the driver assistance
syste mabove the dashboard into the driver's
field of vision. Thi sallow sthe head-up displa yto
collect information withou tyou havin gtotake
your eyes off of the road.
Ar equirement for the displa yofthe contents is
tha tthe following functions ar eavailable in the
vehicl eand ar eswitched on:
R Cruise contro land SPEEDTRONIC
R DISTRONI CPLUS
R Traffi cSignA ssist
R Navigation
Important safety notes The head-up displa
yisonlyana idand is not a
substitute for attentiv edriving.
Speed limits and overtaking restrictions ar enot
always correctl ydisplayed .Traffi csigns always
have priority ove rthe Traffi cSignA ssist display.
The visibility of the head-up displa yisinfluenced
by the following conditions:
R the driver's seat position
R the positioning of the displa yimage
R the genera llig ht conditions
R sunglasse swithp olarisation filters
R We troa ds urfaces
R blocking of sunlight by objects on the display
cover In the event of extreme sunlight, sections of the
displa ymayfade .This ca nbereversed by
switching the head-up displa yoff and on again.
i Vehicles with the head-up displa
yareequip-
pe dw ithas pecial windscreen. Shoul drepairs
be necessary ,havet he windscreen replaced
at aq uali fied specialis tworkshop.
Displays and operation Switchin
gthe head-up displa yon/off X
Press button :.
When the head-up displa yisswitched on, the
displa yappears in the driver's field of vision.
Standard displays in the head-up display
Th eh ead-u pdisplay shows the following con-
tents and information: :
Navigation messages
; Current speed
= Cruise control ,SPEEDTRONIC or
DISTRONI CPLUSs etspeed
? Detected instructions and traffi csigns Displays an
doperation
235On-boardcompu tera nd displays Z

AMG displays in th
ehead-up display
AM Gd isplays are available in Mercedes-AMG
vehicles. The head-up display shows th
efollowing
contents and information:
: Upshif tindicator
; Currently selected gear ,gearshif toptions
when shiftin gmanually
= RACETIMER
? Lap
A Curren tengines peed
B Curren tspeed
Settin goptions
You can mak ethe followin gsettings in th ehead-
up display submenu:
R Adjus tthe positio nofthehead-up display on
th ew indscree n(Ypage 247)
R Adjus tthe brightness of th edisplays in the
head-up display (Y page 247)
R select desired displays in th ehead-up display
(Y page 246)
Usin gthe Displa ycontent
Displa ycontent function ,you
can ,depending on your vehicle's equipment,
choos ebetween four standard displays. The
selected contents then appear in th ehead-up
display.
In Mercedes-AM Gvehicles, you can also
choos ebetween two AM Gdisplays. If you
select an AM Gdisplay, th ehead-up display
shows AMG-specific contents.
If you select adisplay wit htraffic signs, detec-
te dt raffic sign sfromT raffic Sig nAssist
appear in th ehead-up display. Menu
sand submenus Menu overview
Press the òbuttonont hesteering whee lto
open th emenulist.
Operating th eon-bo ard computer (Y page 233).
Dependin gonthevehicl eequipment, you can
select th efollowin gmenus:
R Trip Trip menu(Ypage 236)
R Navi
Navi menu(navigation instructions)
(Y page 238)
R Radio
Radio menu(Ypage 240)
R Media
Media menu(Ypage 240)
R Telephone
Telephone menu(Ypage 242)
R Assistanc egraphic
Assistanc egraphic menu(Ypage 243)
R Service
Service menu(Ypage 244)
R Settings
Settings menu(Ypage 244)
R AMG
AMG men uinM ercedes-AM Gvehicles
(Y page 249) Trip menu
Standar ddisplay X
Press and hold the %buttonont hesteer-
ing whee luntil the Trip Tripmenuwitht rip
meter :and total distanc erecorder ;
appears. 236
Menu
sand submenusOn-boar dcomputer and displays