MERCEDES-BENZ GL550 2008 X164 Owner's Manual
Page 361 of 601
360 Operation
Driving instructions
Driving downhill
Drive slowly.
Do not drive at an angle to the incline.
Steer into the line of gravity and drive
with the front wheels pointing straight
downhill. Otherwise, the vehicle may
slide sideways off the path and roll
over.
Shift automatic transmission to
position1 (
page 197).
On steep inclines, use the Downhill
Speed Regulation (
page 273).
Utilize the engine’s braking power to
reduce vehicle speed.
If this is insufficient, apply the brake
gently. Make sure the vehicle is moving
in the line of gravity.
Check the brakes after a lengthy down-
grade drive.Driving through water
1Fording depth
Before driving through water, deter-
mine its depth.
iThe special Off-road – ABS (page 102)
setting allows for precise and brief (cyclical)
blocking of the front wheels, permitting them to
dig into loose ground.
Remember that, when stopped, the front wheels
slide across a surface and thus lose their ability
to steer the vehicle.Vehicles with air
suspension
program1
Raised level20.00 in (50 cm)
Vehicles with
enhanced off-road
package*1
Off-road 3 level23.60 in (60 cm)
Off-road 2 level20.00 in (50 cm)
Off-road 1 level20.00 in (50 cm)
!The water depth must not exceed the
respective value listed in the table. The ground
under the water might not be firm which could
result the water being deeper than expected
when driving the vehicle through it. Please note
that the water level is correspondingly lower for
flowing water.
164.boo Seite 360 Freitag, 30. März 2007 12:54 12
Page 362 of 601
361 Operation
Driving instructions
Select the highest vehicle level
possible (
page 279).
Switch to off-road driving program
(
page 277) or LOW RANGE mode*
(
page 201) before driving through
water.
Shift automatic transmission to
position1 or2 (
page 197).
Avoid high engine speeds.
Enter and leave the water only at a
shallow spot, driving at walking speed.
Drive through the water slowly and at a
constant speed.
Do not stop vehicle while immersed in
water, and do not shut off the engine.
There is a very high level of driving re-
sistance in water. The surface is slip-
pery and may not be firm, making
pulling away in water difficult and dan-
gerous.
Make sure that only small bow waves
are formed when driving the vehicle
through water.
Clean mud off the tire tread after driv-
ing through water.
To dry the brakes, apply pressure to the
brake pedal several times while driving
after leaving the water.Crossing obstacles
!Never accelerate before driving into the
water. The bow wave could force water into the
engine and auxiliary equipment, thus damaging
them.
!Do not open any of the vehicle’s doors while
driving through water. Water could otherwise en-
ter the vehicle interior and damage the vehicle’s
electronics, as well as the interior equipment.
!Obstacles can damage the vehicle
underbody or suspension components. If possi-
ble use the assistance of a second person out-
side the vehicle to scout the path you intend to
take and check for adequate ground clearance
when you cross obstacles with your vehicle. The
person assisting you outside the vehicle should
always be a safe distance away from the vehicle
and positioned so that he or she cannot get hurt
in case of any unexpected vehicle movement.
After off-road driving or crossing obstacles, in-
spect vehicle for any damage, especially vehicle
underbody and suspension components. Failure
to do so can adversely affect the vehicle’s future
performance, including increased chance of an
accident.
164.boo Seite 361 Freitag, 30. März 2007 12:54 12
Page 363 of 601
362 Operation
Driving instructions
When driving over tree stumps, big rocks
and other obstacles, observe the following
rules:
Make sure the off-road driving program
(
page 277) or if equipped the LOW
RANGE mode* (
page 201) is
switched on.
Avoid high engine speeds.
Shift automatic transmission to
position1 (
page 197).
Check the vehicle clearance before
crossing obstacles.
Cross obstacles (e.g. tree stumps or
big rocks) very slowly by aiming one of
the front wheels at the center of the ob-
stacle, and repeat same with the rear
wheel.Driving on sand
When driving on sand, observe the follow-
ing rules:
Set the raised level (page 279).
Avoid high engine speeds.
Shift automatic transmission into a
gear range that is appropriate for the
terrain.
In sandy soil, drive at a steady speed as
conditions permit. This helps overcome
the vehicle rolling resistance and re-
duce the likelihood of the vehicle sink-
ing into the ground.
Drive in tracks of other vehicles if they
are not too deep and you have suffi-
cient clearance.
Ruts
A number of off-road tracks or other by-
ways have deep ruts which can cause the
underbody to come in contact with the
ground.
Make sure the off-road driving program
(
page 277), or if equipped, the LOW
RANGE mode* (
page 201) is
switched on.
Set the raised level (page 279).!Special attention is needed when you cross
obstacles on a steep incline.
The vehicle could slide sideways as a result of its
possible slanted position which in turn may
result in the vehicle tipping or rolling over.
Warning!G
Do not reduce the tire inflation pressure
before driving through sand. However, if you
do so, remember to correct the tire inflation
pressure (
page 395) before continuing
your trip. Driving with reduced tire inflation
pressure increases the risk of losing control
of the vehicle and rolling over.
164.boo Seite 362 Freitag, 30. März 2007 12:54 12
Page 364 of 601
363 Operation
Driving instructions
Avoid high engine speeds.
Shift automatic transmission to
position1 (
page 197).
Drive next to the ruts rather than
through them if at all possible.
If the ruts are too deep to drive in, drive
with one side of the vehicle on the
grassy center strip if the route permits.Returning from off-road drivingOff-road driving increases strain on the
vehicle.
We recommend that you inspect the vehi-
cle for possible damage after each off-road
trip. Recognizing any damage and a subse-
quent timely repair reduces the chance of
a possible breakdown or accident later on.
Proceed as follows:
Switch off the off-road driving program
(
page 278) or the LOW RANGE
mode* (
page 201).
Switch off the DSR (page 274).
Set the differential locks* to AUTO
(
page 205).
Lower the vehicle back to a level
suitable for road conditions, e.g. High-
way/High-speed level (
page 279).
Clean all exterior lamps and check for
possible damage.
!Check that the ruts are not too deep and
your vehicle’s clearance is sufficient. Otherwise:
your vehicle may be damaged
the underbody of the vehicle may come in
contact with the ground and you may get
stuck
Warning!G
If you feel a sudden significant vibration or
ride disturbance, or you suspect that possi-
ble damage to your vehicle has occurred,
you should turn on the hazard warning flash-
ers, carefully slow down, and drive with cau-
tion to an area which is a safe distance from
the roadway.
Inspect the tires and under the vehicle for
possible damage. If the vehicle or tires ap-
pear unsafe, have it towed to the nearest
Mercedes-Benz Light Truck Center or tire
dealer for repairs.
Damage to the vehicle may influence driving
comfort and pose the risk of accident to you
and other drivers.
164.boo Seite 363 Freitag, 30. März 2007 12:54 12
Page 365 of 601
364 Operation
Driving instructions
Clean the front and rear license plate.
Remove excessive dirt from tires,
wheels, wheel housings, and under-
body.
For instance, after driving in mud, clean
the radiator, chassis, engine, brakes,
and wheels from extreme dirt using a
strong jet of water.
Check tires for possible damage.
Inspect vehicle underbody, oil pan,
brake hoses, etc., as well as vehicle un-
derbody for possible damage.
Check for brush or branches caught in
the underbody.
After continued operation in mud,
sand, water or other dirty conditions
clean the brake discs, wheels, brake
pads and check and clean axle joints.
Conduct a brake test.
Trailer towing Trailer hitch*
Only install a trailer hitch receiver ap-
proved for your vehicle.
For information on availability and in-
stallation, contact an authorized
Mercedes-Benz Light Truck Center.
The bumpers on your vehicle are not
designed for use with clamp-type hitch-
es.
Do not attach rental hitches or other
bumper-type hitches to them.
To reduce the possibility of damage, re-
move the hitch ball adaptor from the
receiver when not in use.
!Brush or branches could increase the possi-
bility of a fire, as well as cut fuel and/or brake
lines, puncture rubber bellows of the axles or
drive shafts.
Warning!G
Failure to use proper equipment and driving
technique can result in a loss of vehicle con-
trol when towing a trailer.
Improper towing or failure to follow the in-
structions in this manual can result in vehi-
cle damage and/or serious personal injury.
Follow the guidelines below carefully to as-
sure safe trailer operation.
Contact an authorized Mercedes-Benz Light
Truck Center should you require an explana-
tion of information contained in this manual.
164.boo Seite 364 Freitag, 30. März 2007 12:54 12
Page 366 of 601
365 Operation
Driving instructions
Electrical connections
The vehicle is prewired to accept the
seven-wire harness included in the
Mercedes-Benz approved trailer hitch
receiver kit.
For further information, contact an autho-
rized Mercedes-Benz Light Truck Center.
Vehicle and trailer weights and ratings
Gross Vehicle Weight Rating (GVWR) is the
maximum permissible vehicle weight:
6944 lb (3150 kg).
Gross Vehicle Weight (GVW):
Comprises weight of vehicle including fuel,
tools, spare wheel, installed accessories,
passengers, cargo and trailer tongue. It
must never exceed the GVWR.Gross Axle Weight Rating (GAWR) is the
maximum permissible axle weight:
The Gross Trailer Weight (GTW) is the
weight of the trailer plus the weight of all
cargo, equipment, luggage etc. loaded on
the trailer. The maximum permissible
gross trailer weight to be towed:
7500 lb (3402 kg).
Trailer Tongue Weight Rating (TWR) is the
maximum permissible weight on the trailer
tongue:
600 lb (272 kg) limit for Mercedes-Benz
approved hitch receiver.Loading a trailer
When loading a trailer, you should ob-
serve that neither the permissible GTW,
nor the GVWR are exceeded.
Maximum permissible values are listed
on the safety compliance certification
labels for the vehicle and for the trailer
to be towed.
The lowest value listed must be select-
ed when determining how the vehicle
and trailer are loaded.
The tongue weight at the hitch ball
must be added to the GVW to prevent
exceeding your Mercedes-Benz tow
vehicle’s rear GAWR.
iA four-pole conversion plug is available from
your authorized Mercedes-Benz Light Truck
Center as a spare part.
GL 320 CDI
Front3306 lb (1500 kg)
Rear3968 lb (1800 kg)
GL 450, GL 550
Front3240 lb (1470 kg)
Rear3968 lb (1800 kg)
iWe recommend loading the trailer in such a
manner that it has a Tongue Weight (TW)
between 8% and 15% of the Gross Trailer Weight
(GTW).
iMaximum trailer weight ratings are calculat-
ed assuming the vehicle, plus driver. The weight
of other accessories, passengers and cargo will
reduce the maximum trailer weight and Tongue
Weight (TW) your vehicle can tow.
164.boo Seite 365 Freitag, 30. März 2007 12:54 12
Page 367 of 601
366 Operation
Driving instructions
Checking weights of vehicle and trailer
To assure that the tow vehicle and trail-
er are in compliance with the maximum
permissible weight limits have the load-
ed rig (tow vehicle including driver, pas-
sengers and cargo, trailer fully loaded)
weighed on a commercial scale.
Check the vehicle’s front and rear
Gross Axle Weight (GAW), the Gross
Trailer Weight (GTW) and Tongue
Weight (TW).
The values as measures must not
exceed the weight limits listed under
“Vehicle and trailer weight and ratings”
(
page 365).Attaching a trailerObserve maximum permitted trailer
dimensions (width and length).
Most states and all Canadian provinces
require
safety chains between your tow vehicle
and the trailer.
The chains should be criss-crossed
under the trailer tongue. They must be
attached to the hitch receiver, and not
to the vehicle’s bumper or axle.
Make sure to leave enough slack in the
chains to permit turning corners.
a separate brake system at various
trailer weights.
a break-away switch on trailers with a
separate brake system. Check with
your local state laws for specific
requirements.
The switch activates the trailer brakes
in the possible event that the trailer
might separate from the tow vehicle.
Warning!G
While you are coupling or decoupling a trail-
er, make sure that you do not
lock or unlock
open or close
a vehicle door or the tailgate.
The vehicle’s level could change and you
could endanger yourself and/or others as a
result.
Make sure that you do not operate the ADS
button* (
page 279) or the vehicle level
control system (
page 279) when cou-
pling/decoupling the trailer.
164.boo Seite 366 Freitag, 30. März 2007 12:54 12
Page 368 of 601
367 Operation
Driving instructions
Make sure the automatic transmission
is set toP (
page 191).
Set the parking brake for the vehicle
(
page 67).
Start the engine (page 56).
Set the vehicle level to Highway
(
page 279).
Vehicle with ADS*: Set the ADS* to
AUTO or COMFORT (
page 278).
Turn off the engine (page 68).
Close all doors and the tailgate.
Attach the trailer.
Plug in all electrical connectors.
Towing a trailer
There are many different laws, including
speed limit restrictions, having to do with
trailer towing. Make sure your rig will be le-
gal, not only for where you reside, but also
for where you will be driving. A good
source for this information can be the po-
lice or local authorities.Note the following points, when driving
with the trailer:In order to gain skill and an understand-
ing of the vehicle’s behavior, you
should practice turning, stopping and
backing up in an area which is free from
traffic.
Before you start driving check the
trailer hitch
break-away switch
safety chains
electrical connections
lighting and tires
Adjust the mirrors (page 51) to
permit unobstructed view beyond rear
of trailer.
If the trailer has electric brakes, start
your vehicle and trailer moving slowly,
and then apply only the trailer brake
controller by hand to make sure the
brakes are working properly.
!Do not connect a trailer brake system (if
trailer is so equipped) directly to the vehicle’s
hydraulic brake system, as your vehicle is
equipped with antilock brakes. If you do, neither
the vehicle’s brakes nor the trailer’s brakes will
function properly.
iThe provided vehicle electrical connector for
trailer towing has a brake signal wire for hook-up
to a brake controller.
You should consider using a trailer sway control
system. For further information, contact an
authorized Mercedes-Benz Light Truck Center.
iWhen you are towing a trailer, the vehicle
level always remains in the Highway setting.
The following applies additionally when towing a
trailer:
The vehicle is lowered to the highway level
when it reaches a speed of 5 mph (8 km/h)
if not set to highway level.
The high-speed level is not available.
The restrictions that apply to towing also apply
when using accessories that are connected to
the trailer power socket, such as a bicycle rack.
164.boo Seite 367 Freitag, 30. März 2007 12:54 12
Page 369 of 601
368 Operation
Driving instructions
Always secure items in the trailer to
prevent load shifts while driving.
When towing a trailer, check occasion-
ally to make sure the load is secure,
and that lighting and trailer brakes (if
so equipped) are functioning properly.
Take into consideration that when tow-
ing a trailer, the handling characteris-
tics are different and less stable from
those when operating the vehicle with-
out a trailer.
It is important to avoid sudden maneu-
vers.
The vehicle and trailer combination is
heavier, and therefore is limited in ac-
celeration and climbing ability, and re-
quires longer stopping distances.
It is more prone to reacting to cross
wind gusts, and requires more sensi-
tive steering input.
If possible, do not brake abruptly, but
rather engage the brake slightly at first
to permit the trailer to activate its
brake. Then increase the braking force.
If the transmission repeatedly shifts
between gears on inclines, manually
shift to a lower gear (select 4, 3, 2 or 1)
(
page 197).
A lower gear and reduction of speed re-
duces the chance of engine overload-
ing and/or overheating.
On very steep inclines, not manageable
with automatic transmission in1,
switch on off-road driving program
(
page 278) or LOW RANGE mode*
(
page 201).
When going down a long hill, shift into
a lower gear and use the engine’s brak-
ing effect.
Avoid riding the brakes, thus overheat-
ing the vehicle and trailer brakes.
If the engine coolant rises to an ex-
tremely high temperature (coolant tem-
perature needle approaching the red
zone) when the air conditioning is on,
turn off the air conditioning system.
Engine coolant heat can be additionally
vented by opening the windows,
switching the climate control fan speed
to high and setting the temperature
control to the maximum hot position.
Extreme care must be exercised since
your vehicle with a trailer will require
additional passing distance ahead than
when driving without a trailer.
Because your vehicle and trailer is
longer than your vehicle alone, you will
also need to go much farther ahead of
the passed vehicle before you can re-
turn to your lane.
!If the trailer should begin to sway, reduce
the vehicle’s speed immediately.
In no case attempt to straighten out the tow
vehicle and trailer by increasing the speed.
164.boo Seite 368 Freitag, 30. März 2007 12:54 12
Page 370 of 601
369 Operation
Driving instructions
Uncoupling the trailerMake sure the automatic transmission
is set toP (
page 191).
Set the parking brake for the vehicle
(
page 67).
Start the engine (page 56).
Close all doors and the tailgate.
Set the parking brake for the trailer.
Disconnect all electrical plug connec-
tors.
Uncouple the trailer.
Make sure that the trailer coupling is
free of load.
Turn off the engine (page 68).
Warning!G
While you are coupling or decoupling a trail-
er, make sure that you do not
lock or unlock
open or close
a vehicle door or the tailgate.
The vehicle’s level could change and you
could endanger yourself and/or others as a
result.
Make sure that you do not operate the ADS
button* (
page 279) or the vehicle level
control system (
page 279) when cou-
pling/decoupling the trailer.
Warning!G
As soon as you disconnect the electrical
connection between the trailer and the
vehicle, the vehicle will lower. To help avoid
personal injury, make sure no one is near
the wheel housing or underneath the vehicle
before the electrical connection is discon-
nected.
When you uncouple the trailer, the vehicle is
temporarily raised because the springs are
relieved of load. Be especially careful during
this process, as you could otherwise injure
yourself and/or others. Make sure that any
persons remaining in the vehicle do not
press the switches for vehicle level control
or the ADS*.
164.boo Seite 369 Freitag, 30. März 2007 12:54 12