MINI Hardtop 2 Door 2017 Owner's Manual

6.Insert and latch a new wiper blade in re~verse order.7.Fold down the wiper arm.
Rear
wiper
blade
1.Fold up and hold the wiper arm firmly.2.Turn the wiper blade all the way back.3.Push the wiper blade out of the fasteningby continuing to turn it all the way.4.Insert the new wiper blade by following the
steps in reverse order. The wiper blade
must engage audibly.5.Fold down the wiper arm.
Light/bulb
replacement
General
information
Lights
and
bulbs
Lights and bulbs make an essential contribution
to vehicle safety.
The manufacturer of the vehicle recommends that you have appropriate work performed by a dealer

Headlight
glass
Condensation can form on the inside of the ex~
ternal lights in cool or humid weather. When driving with the lights switched on, the conden~
sation evaporates after a short time. The head~ light glass does not need to be changed.
If despite driving with the lights switched on,increasing humidity forms, e. g. water droplets
in the lamp, the manufacturer of your vehicle
recommends having it checked by a dealer

5.Remove the bulb from the headlight hous~ing.6.Insert the new bulb and install the cover in
the reverse order.
Turn
signal
Follow the general instructions on lights and
bulbs, refer to page 221.
Bulbs: PW24W
With white turn signal lights: PWY24W
1.Turn the steering wheel.2.Turn the lid counterclockwise, arrow 1, and remove.3.Unscrew the inner lid counterclockwise,and remove it.4.Pull bulb holder out of the bulb housing; ifneeded, loosen it with small tilting move~ments if possible.5.Pull the bulb out of the fixture.6.Insert the new bulb and install the cover in
the reverse order.
Parking
lights/fog
lights/daytime
running
lights
Follow the general instructions on lights andbulbs, refer to page 221.
Bulbs:
'

'

With white turn signal lights: PWY24W1.Turn the steering wheel.2.Turn the lid counterclockwise, arrow 1, andremove.3.Unscrew the inner lid counterclockwise,and remove it.4.Pull bulb holder out of the bulb housing; ifneeded, loosen it with small tilting move~ments if possible.5.Pull the bulb out of the fixture.6.Insert the new bulb and install the cover in
the reverse order.Tail
lights,
bulb
replacement
Overview
Vehicles
with
a
rear
fog
lamp1Side tail lamps2Rear fog lamp3License plate lamp4Center brake lamp
Vehicle
with
two
rear
fog
lights
1Side tail lamps2Rear fog lights3License plate lamp4Center brake lampSeite 225Replacing
componentsMOBILITY225
Online Edition for Part no. 01 40 2 915 044 - X/16

Side
tail
lamps1Brake lights/tail lamps2Turn signal3Reversing lights
Side
LED
tail
lights
1Tail lamps2Turn signal3Brake light4Reversing lights
Side
tail
lights
Follow the general instructions on lights and
bulbs, refer to page 221.
Bulbs: P21W1.Open the tailgate.2.Remove left or right cover.3.Through the opening, loosen the plug con~
nector, arrow 2 on the bulb holder.
Press the latches together, arrows 1, and
remove the bulb holder.4.Remove the bulb holder from the opening.5.Press the nonworking bulb gently into the socket, turn counterclockwise and remove.'

'

The wire is long enough to guide the socketdown and through between any heat shield
that may be installed and the bumper.4.Replace nonworking bulb.5.To install the new bulb, proceed in reverse
order of removal.
Right fog lamp:
1.Turn the bulb socket counterclockwise and
remove.
The wire is long enough to guide the socket down and through between any heat shield
that may be installed and the bumper.2.Replace nonworking bulb.3.To install the new bulb, proceed in reverse
order of removal.
Side
turn
signal,
bulb
replacement
Follow the general instructions on lights and
bulbs, refer to page 221.
Bulbs:
'

Vehicle
batteryMaintenance
The battery is maintenance-free.
The added amount of acid is sufficient for the
service life of the battery.
More information about the battery can be re~
quested from a dealer

Fuses
Safety
information WARNING
Incorrect and repaired fuses can overload
electrical lines and components. There is a risk of fire. Never attempt to repair a blown fuse.Do not replace a nonworking fuse with a sub~stitute of another color or amperage rating. '