Specifications MITSUBISHI 3000GT 1994 2.G User Guide

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Meters and Gauaes
SERVICE SPECIFICATIONS
Items
Standard values
Speedometer indicationerror
mph
2019-22
4038-44
1 57-66
1 76-88I
1001 94-110I
Tachometerindicationerrorrpm1,000f 100
3,000
f150
5,000f 250
6,000
Ik 300
Fuel gauge unit resistance R/ Point F_I3f2I
Point E
Fuel gauge unit float heightPoint F
mm (in.)
Point E
Engine coolant temperature gauge unit resistance [at 70°C (158”F)] Q110+7
18.6-21.6 (.73-.85)193.4-l
96.4 (7.61-7.73)
104 f 13.5
Fuel gauge resistance QBetween A - B/ Approx. 254I
Between A - CApprox. 101I
Between B - CApprox. 153I
Enginecoolant temperature Between A - B
gauge resistance QBetween A - CApprox. 51
Approx. 139
Between B
- C/ Approx. 190I
Oil pressure gauge resistance QApprox. 42I
Pressure gauge resistance <Turbo> QApprox. 72ISEALANT
ItemsSpecified sealantType
Engine coolant temperature gauge3M Nut Locking Part No. 4171 or Semi-drying sealant
unitequivalent
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-26CHASSIS ELECTRICAL - Meters and Gauges
<Rear wheels on free rollers>
Free
r&Hers -
Sear wheels raised on jack>
?qi&%!g
Rigid rack oooo2297
Anchor plate
-w216AO864
bracket
/IZ16FO13300002298ON-VEHICLE
SERVICEINSPECTION
SPEEDOMETER CHECK
(1) Assure tire pressure at standard value. (Refer to GROUP
- Specifications.)
(2)Gt the vehicle on a speedometer tester.
(3)Set free rollers securely on the floor according to the wheel-base and rear tread of the vehicle (when rear wheels
are to be set on free rollers).
(4) Raise the rear wheels on a jack and place rigid racks
to support the specified positions of the side sills (whenrear wheels are to be raised on a jack).
(5) Make sure the parking brake has been set.
cPWD>
(6)Attach anchoring bars on the tie-down brackets and secure
their ends to the anchor plates.(7) Make sure the tension on the right and left bars is the
same. Also be sure there is enough tension on each bar.(8) Attach a chain or wire to the rear tie-down hole. Make
sure the end of the wire or chain is secured firmly.
(9) Take all other necessary precautions.
(1O)Use a speedometer tester to measure the speedometer’s
indication error.
Standard value:
Standard indication
mph
Allowable range mph
2019-22
4038-44
8057-66
1 801 76-88--I
1 100
Caution
1 94-110
Do not operate the clutch or accelerator abruptly or
decelerate during the operations.
d
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System
LIGHTING SYSTEM
54-35
L/ SPECIFICATIONSGENERAL SPECIFICATIONS
Exterior lights
ItemsSpecificationsHeadlight W
65/45*‘, 60151 *2Fog light W
55
Front combination light
Turn-signal light / side marker light CP27/8 (1157)” or 27 (1156)*2
Rear combination lightTurn-signal light / side marker and tail light CP32/2 (2057)
Stop light / side maker and tail lightCP32/2 (2057)
Back-up light CP
32 (1156)
License plate light CP3 (168)
High-mountedstop
Vehicles without rear spoiler CP32 (1156)
light
Vehicles with fixed rear spoiler W4
Vehicles with active rear spoiler
Engine compartment inspection light WLED (Light Emitting Diode)3.8 (194)
Interior
lights
ItemsFoot light WSpecifications
3.4 (158)
IDome light W8ISpot light W
8Door light W
5
Glove compartment light W
Luggage compartment light W3.4 (158)
5
NOTE
;he values in parentheses denote SAE trade number.
Up to 1993 models
l 2From 1994 modelsSERVICE SPECIFICATIONS
ItemsLimitI
Headlight intensity
I
20,000 cd or moreI
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Column Switch
COLUMN SWITCH
SPECIFICATIONS
GENERAL SPECIFICATIONS
54-111
ItemsSpecifications
1 Lighting switchRated load A1 0.22 f 0.05IIII
1 Voltage drop V0.2 or less
I Turn-signal switch) Rated load A1 6.6kO.5III/I
Dimmer/passing switch
Voltage drop V
Rated load A
0.2 or less
High beam : 10.7 + 0.8IIII
1 Low beam : 9.8 f 0.7IIII
j Passing : 20.5 + 1.5IIII
/ Voltage drop V0.2 or less
NOTE
For the wiper and washer switch, refer to GROUP 51 - Windshield Wiper and Washer.SPECIAL TOOL
Steering wheel puller
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Horn54-115
HORN
SPECIFICATIONS
GENERAL SPECIFICATIONS
Horn (Except for theft-alarm horn)
ItemsI Specifications
Type
Effective sounding voltage V
Power consumption A
Sound level dB
Fundamental frequency Hz
“low” sound
“high” sound
“low” sound
“high” sound
Fiat type
11.5-15
3.0
100-112
100-112350-390395-435
Theft-alarm horn
1 ItemsI Specifications
1 Type1 Flat typeI
Effective sounding voltage V
Power consumption A
Sound level dB
Fundamental frequency Hz
11-14.5
Max. 3.5
105-120I
I 405-435
TROUBLESHOOTING
COMPONENT LOCATION
OPERATIONl
The horn switch always receives battery voltagevia the dedicated fuse (6) and the coil of the
horn relay.
l
When the horn switch is set to ON, the contactsof the horn relay close.
Then current flows through the dedicated fuse
(6) to the contacts of the horn relay, the hornand ground, causing the horn to sound.1. One of the horn does not sound.
TROUBLESHOOTING HINTSl Check the horn.
2. Horns do not sound.
l Check the horn switch.
l Check the dedicated fuse (6).
NOTE
(1) For vehicles equipped with the theft-alarm sys-tem, refer to
P.54-205.
(2) For information concerning the horn relay and
theft-alarm horn relay, refer to
P.54-?18.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Cigarette Lighter54-119
/CIGARETTE LIGHTER
LiSPECIFICATIONS
GENERAL SPECIFICATIONS
Items
Max. input W
Reset time second
1 Thermal fuse fusion temperature “C (OF)
Specifications
120
Within 18
180-250 (356-482)I
/
LJ
TSB Revision