keyless entry MITSUBISHI L200 2020 Owner's Manual (in English)

CAUT,ONzDispose of used batteries according to regu-
lations for the disposal of battery.NOTEz You may purchase a replacement battery at
an electric appliance store.
z A
MITSUBISHI MOTORS Authorized
Service Point can replace the battery for you
if you prefer.
1. Remove the screw (A) from the key.
(Keyless entry key only)
2. Remove the emergency key from the
key. (Keyless operation key only)
Refer to “Emergency key” on page 3-11.
3. With the MITSUBISHI mark facing you, insert the cloth-covered tip of a straight
blade (or minus) screwdriver into the
notch in the key case and use it to open
the case.NOTEz Be sure to perform the procedure with the
MITSUBISHI mark facing you. If the
MITSUBISHI mark is not facing you when
you open the key case, the switches may
come out.4. Remove the used battery.
5. Install a new battery with the + side (B)
up.
6. Close the key case firmly.
7. Attach the screw (A) removed in step 1.
(Keyless entry key only)
8. Install the emergency key removed in
step 2. (Keyless operation key only)
Keyless entry system*
3-072.7(20(1Locking and unlocking3 Keyless entry key Keyless entry key Keyless operation key Keyless entry key+ side - side
Coin type battery CR1620 Keyless operation key+ side - side
Coin type battery CR2032

NOTEzEven if the vehicle suffers significant defor-
mation from a collision etc., depending on the location and angle of the collision, as
well as on the shape and condition of the
other object in the collision, the doors may
not unlock. The extent of deformation or damage to the vehicle does not necessarily correlate with unlocking of the doors.
z These functions are activated when the vehi-
cle is shipped from the factory. If you wish to activate or deactivate these functions,please contact a MITSUBISHI MOTORS
Authorized Service Point.
Unlocking by using the ignition
switch, the engine switch or theselector lever
It is possible to unlock all of the doors when- ever as follows.
[Vehicles with M/T@
The ignition switch is turned to the “LOCK”
position or the operation mode is put in OFF.
[Vehicles with A/T@
The selector lever is placed in the “P” (PARK) position while the operation mode is
in ON. Or the operation mode is put in OFF.

These functions are deactivated when the ve-
hicle is shipped from the factory. If you wishto activate or deactivate these functions,
please contact a MITSUBISHI MOTORS
Authorized Service Point.Dead Lock System*
The Dead Lock System helps prevent theft.
When the keyless entry system or the keyless operation function has been used to lock all
of the doors, the Dead Lock System makes it
impossible to unlock the doors using the in- side lock knobs.
CAUT,ONz Do not set the Dead Lock System when
someone is inside the vehicle. With the Dead
Lock System set, it is not possible to unlock the doors using the inside lock knobs. If you
erroneously set the Dead Lock System, un-
lock the doors using the UNLOCK switch on the key or using the keyless operation
function.Setting the system
1. Turn the ignition switch to the “LOCK”
position and then remove the key (vehi-
cles with keyless entry system), or put the operation mode in OFF (vehicles
with keyless operation system).
2. Get out of the vehicle. Close all of the
doors.
3. Press the LOCK switch (A) on the key,
the driver’s or front passenger’s door
lock/unlock switch (C) to lock all of the doors. The turn-signal lamps will blink
once.
4. Press the switch again within 2 seconds.
The turn-signal lamps will blink three
times to show that the Dead Lock Sys- tem has been set.
Dead Lock System*
3-182.7(20(1Locking and unlocking3 Keyless entry system Keyless operation system