clock MITSUBISHI LANCER EVOLUTION VI 1999 Owner's Manual

SRS – General Information52B-2
GENERAL INFORMATION
To improve safety, the SRS is available as optional
part.
The SRS consists of two air bag modules, SRS
air bag control unit (SRS-ECU), SRS warning lamp
and clock spring. One air bag is located in the
centre of the steering wheel and another above
the glove box. Each air bag has a folded air bag
and an inflator unit. The control unit under the floor
console monitors the system and has a safing G
sensor and an analog G sensor. The warning lamp
on the instrument panel indicates the operationalstatus of the SRS. The clock spring is installed
in the steering column.
Only authorized service personnel should do work
on or around the SRS components. Those service
personnel should read this manual carefully before
staring any such work. Extreme care must be used
when servicing the SRS to avoid injury to the service
personnel (by inadvertent deployment of the air
bags) or the driver (by rendering the SRS
inoperative).
Air bag module
(Driver’s side)Clock springAir bag module
(Front passenger’s side)
Diagnosis
connector
SRS-ECU
SRS warning lamp

SRS – SRS Service Precautions52B-3
SRS SERVICE PRECAUTIONS
1. In order to avoid injury to yourself or others
from accidental deployment of the air bag during
servicing, read and carefully follow all the
precautions and procedures described in this
manual.
2. Do not use any electrical test equipment on
or near SRS components, except those
specified on P.52B-5.
3. Never Attempt to Repair the Following
Components:

SRS air bag control unit (SRS-ECU)

Clock Spring

Air Bag Module
(Driver‘s side or front passenger’s side*)NOTE
*: Vehicles with front passenger’s air bag
If any of these components are diagnosed as
faulty, they should only be replaced, in
accordance with the INDIVIDUAL COM-
PONENT SERVICE procedures in this manual,
starting at page 52B-22.
4. After disconnecting the battery cable, wait 60 seconds
or more before proceeding with the following work.
The SRS system is designed to retain enough voltage
to deploy the air bag for a short time even after the
battery has been disconnected, so serious injury may
result from unintended air bag deployment if work
is done on the SRS system immediately after the
battery cables are disconnected.
5. Do not attempt to repair the wiring harness connectors
of the SRS. If any of the connectors are diagnosed as
faulty, replace the wiring harness. If the wires are
diagnosed as faulty, replace or repair the wiring harness
according to the following table.
Battery Insulating tape
SRS-ECU connector

SRS – SRS Service Precautions52B-4
SRS-ECU
terminal No.Harness connector
(No. of terminals,
colour)Destination of harnessCorrective action
1 to 421 pins, yellow––
5Body wiring harness → Clock spring → Air bag
module (Driver’s side)
Correct or replace each
wiring harness Replace
6
module (Driver’s side)wiring harness. Replace
clock spring.
7*Body wiring harness → Air bag module (Front
passenger’s side)
Correct or replace each
wiring harness
8*
passenger’s side)wiring harness.
9,10––
11Body wiring harness → Diagnosis connectorCorrect or replace each
wiring harness.
12––
13Body wiring harness → Junction block (fuse No.2)Correct or replace each
wiring harness
14Body wiring harness → Junction block (fuse No.4)
wiring harness.
15Body wiring harness → SRS warning lamp
16 to 19––
20Body wiring harness → EarthCorrect or replace each
wiring harness.
21––
NOTE
*: Vehicles with front passenger’s air bag
6. SRS components should not be subjected to hear over 93C, so remove the SRS-ECU, air bag
module and clock spring before drying or baking the vehicle after painting.
7. Whenever you finish servicing the SRS, check warning lamp operation to make sure that the system
functions properly. (Refer to P.52B-14.)
8. Make certain that the ignition switch is LOCK (OFF) position when the MUT-II is connected or
disconnected.
9. If you have any questions about the SRS, please contact your local distributor.
NOTE
SERIOUS INJURY CAN RESULT FROM UNINTENDED AIR BAG DEPLOYMENT, SO USE ONLY
THE PROCEDURES AND EQUIPMENT SPECIFIED IN THIS MANUAL.

SRS – Troubleshooting52B-8
Code No.21, 22, 61 or 62 Driver’s side air bag module
(squib) systemProbable cause
These diagnosis codes are output if there is abnormal resistance between the input
terminals of the driver’s side air bag module (squib).
The trouble causes for each diagnosis code No. are as follows.
Malfunction of clock spring

Partial disconnection due to incorrect clock spring
neutral position

Malfunction of wiring harnesses or connectors

Malfunction of driver’s side air bag module (squib)

Malfunction of SRS-ECU
Code No.Trouble symptom
21
Short in driver’s side air bag module (squib) or harness short

Short in clock spring

Malfunction of connector*
22
Open circuit in driver’s side air bag module (squib) or open harness

Open circuit in clock spring

Malfunction of connector contact
61
Short in driver’s side air bag module (squib) harness leading to the power supply
62
Short in driver’s side air bag module (squib) harness leading to the earth
NOTE
*: The connector in the squib circuit has a built-in short bar which short-circuits between plus (+) lead and minus
(–) lead of the squib circuit when the connector is not being connected to prevent an accidental air bag deployment
possibly caused by static electricity, etc. Therefore, malfunction of the connector can also be caused by this
short bar which fails to be released even when the connector is reconnected if it is damaged.
MUT-II Self-diag code

Disconnect clock spring
connector B-82.

Connect SRS check har-
ness connector (1).

Erase diagnosis code
memory.
Are code Nos.21, 22, 61 or
62 output?Ye sCheck the following
connectors:
B-82, B-51NG
Repair
OK
Check trouble symptoms.
NG
Check the harness wire
between the SRS-ECU
and clock spring.NG
Repair
OK
Replace the SRS-ECU.
No
Check the clock spring. (Refer to P.52B-30.)NG
Repair
OK
Replace the driver’s side air bag module.
SRS check harness
(MB991613)
Body wiring
harness
Clock spring
1

SRS – SRS Maintenance52B-16
SRS COMPONENT VISUAL CHECK
Turn the ignition key to the LOCK (OFF) position, disconnect
the negative battery cable and tape the terminal.
Caution
Wait at least 60 seconds after disconnecting the battery
cable before doing any further work. (Refer to P.52B-3.)
SRS CONTROL UNIT (SRS-ECU)
1. Check SRS-ECU case and brackets for dents, cracks,
deformation or rust.
Caution
The SRS may not activate if the SRS-ECU is not
installed properly, which could result in serious injury
or death to the vehicle’s driver or front passenger.
2. Check connector for damage, and terminals for
deformation or rust.
Replace SRS-ECU if it fails visual check.
(Refer to P.52B-24.)
AIR BAG MODULES, STEERING WHEEL AND CLOCK
SPRING
1. Remove the air bag modules, steering wheel and clock
spring. (Refer to P.52B-25.)
Caution
The removed air bag modules should be stored in
a clean, dry place with the pad cover face up.
2. Check pad cover for dents, cracks or deformation.
Insulating tape
Battery
Battery (–) cable
SRS-ECU
Pad cover
<Driver’s side>
<Front passenger’s side>
Pad cover

SRS – SRS Maintenance52B-17
3. Check connector for damage, terminals deformities, and
harness for binds.
4. Check air bag inflator case for dents, cracks or deformities.
5. Check harness and connectors for damage, and terminals
for deformation.
6. Check clock spring connectors and protective tube for
damage, and terminals for deformation.
7. Visually check the clock spring case for damage.
8. Align the mating marks of the clock spring and, after
turning the vehicle’s front wheels to straight-ahead
position, install the clock spring to the column switch.
Mating Mark Alignment
Turn the clock spring clockwise fully, and then turn back
it approx. 3 4/5 turns counterclockwise to align the mating
marks.
Caution
If the clock spring’s mating mark is not properly
aligned, the steering wheel may not be completely
rotational during a turn, or the flat cable within the
clock spring may be severed, obstructing normal
operation of the SRS and possibly leading to serious
injury to the vehicle’s driver or front passenger.
9. Install the steering column covers, steering wheel and
the air bag module.
10. Check steering wheel for noise, binds of difficult operation.
11. Check steering wheel for excessive free play.
REPLACE ANY VISUALLY INSPECTED PART IF IT
FAILS THAT INSPECTION. (Refer to P.52B-25.)
Caution
The SRS may not activate if any of the above
components is not installed properly, which could
result in serious injury or death to the vehicle’s driver
or front passenger.<Driver’s side>
Inflator case
Connector
<Front passenger’s side>
Inflator case
Connector
Protective tube
Case
Mating marksProtective tube

SRS – Post-collision Diagnosis52B-20
REPAIR PROCEDURE
WHEN AIR BAG DEPLOYS IN A COLLISION.
1. Replace the following parts with new ones.

SRS-ECU (Refer to P.52B-24.)

Air bag module (Refer to P.52B-25.)
2. Check the following parts and replace if there are any
malfunctions.

Clock spring (Refer to P.52B-25.)

Steering wheel, steering column and intermediate
joint
(1) Check wiring harness (built into steering wheel)
and connectors for damage, and terminals for
deformation.
(2) Install air bag module to check fit or alignment
with steering wheel.
(3) Check steering wheel for noise, binds or difficult
operation and excessive free play.
3. Check harnesses for binding, connectors for damage,
poor connections, and terminals for deformation.
(Refer to P.52B-18.)
WHEN AIR BAG DOES NOT DEPLOY IN LOW-SPEED
COLLISION.
Check the SRS components. If the SRS components are
showing any visible damage such as dents, cracks, or
deformation, replace them with new ones. Concerning parts
removed for inspection, replacement with new parts and
cautionary points for working, refer to appropriate INDIVIDUAL
COMPONENT SERVICE, P.52B-22.

SRS – Post-collision Diagnosis52B-21
SRS-ECU
1. Check SRS-ECU case and brackets for dents, cracks
or deformation.
2. Check connector for damage, and terminals for
deformation.
Air bag modules
1. Check pad cover for dents, cracks or deformation.
2. Check connector for damage, terminals deformities, and
harness for binds.
3. Check air bag inflator case for dents, cracks or deformities.
4. Install air bag module to steering wheel to check fit or
alignment with the wheel.
Clock spring
1. Check clock spring connectors and protective tube for
damage, and terminals for deformation.
2. Visually check the case for damage.
SRS-ECU
<Driver’s side>
Connector
<Front passenger’s side>
Inflator case
ConnectorInflator case
Case Protective tube
Protective tube

SRS – Post-collision Diagnosis / Individual Component Service52B-22
Steering wheel, steering column and intermediate joint
1. Check wiring harness (built into steering wheel) and
connectors for damage, and terminals for deformation.
2. Install air bag module to check fit or alignment with steering
wheel.
3. Check steering wheel for noise, binds or difficult operation
and excessive free play.
Harness connector (body wiring harness)
Check harnesses for binding, connectors for damage, poor
connection, and terminals for deformation. (Refer to P.52B-18.)
INDIVIDUAL COMPONENT SERVICE
If the SRS components are to be removed or replaced as a result of maintenance, troubleshooting,
etc., follow each procedure (P.52B-24 – P.52B-31)
Caution
1. SRS components should not be subjected to hear over 93C, so remove the SRS-ECU, air
bag module and clock spring before drying or baking the vehicle after painting.
Recheck SRS system operability after re-installing them.
2. If the SRS components are removed for the purpose of check, sheet metal repair, painting,
etc., they should be stored in a clean, dry place until they are reinstalled.

SRS – Warning/Caution Labels52B-23
WARNING/CAUTION LABELS
A number of caution labels related to the SRS are
found in the vehicle, as shown in the followingillustration. Follow label instructions when servicing
SRS. If labels are dirty or damaged, replace them.
Steering wheel Air bag module (driver’s side) Clock spring
Glove box Sun visor SRS-ECU
Steering gear and linkage Air bag module
(front passenger’s side)