engine MITSUBISHI MIRAGE 2014 6.G Manual PDF

Features and controls
3-115
3
Vehicles equipped with daytime running lights
[When the engine is started, and the parking brake is released]
The daytime running lights will be illuminated:NOTE
Once the daytime running light come on, they do not go
out until the ignition switch is turned to the “OFF” or
“ACC” position or the operation mode is changed to OFF
or ACC.
[When the engine is not running, or when the engine is running
but the parking brake is not released]
The engine starts when the lights are off.NOTE
Do not leave the headlights and other lights on for a long
period of time when the engine is not running. The battery
will run down.
When it rains, or when the vehicle has been washed, the
inside of the lens sometimes becomes foggy. This is the
same as when window glass mists up on a humid day, and
does not indicate a problem. When the light is switched
on, the heat will dry out the fog. However, if water col-
lects inside the light, have it checked by an authorized
Mitsubishi Motors dealer or a repair facility of your
choice.OFF The daytime running lights illuminated
The daytime running lights illuminated
Parking, tail, front and rear side-marker lights, license
plate and instrument panel lights on
Headlights and other lights on
OFF All lights off
Parking, tail, front and rear side-marker lights, license
plate and instrument panel lights on
Headlights and other lights on
BK0162600US.book 115 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-116 Features and controls
3
Light auto-cutout function (headlights and other
lights)
N00532600570

If the following operation is performed with the combina-
tion headlights and dimmer switch in the “ ” or “ ”
position, the lights automatically turn off.
[Except for vehicles equipped with the F.A.S.T.-key]
The ignition switch is turned to the “OFF” or “ACC” posi-
tion or the key is removed from the ignition switch and the
driver’s door is opened.
[For vehicles equipped with the F.A.S.T.-key]
The operation mode is changed to OFF or ACC and the
driver’s door is opened.

If the following operation is performed with the combina-
tion headlights and dimmer switch in the “ ” or “ ”
position, the lights automatically turn off after about 3
minutes.
[Except for vehicles equipped with the F.A.S.T.-key]
The ignition switch is turned to the “OFF” or “ACC” posi-
tion or the key is removed from the ignition switch and the
driver’s door is not opened.
[For vehicles equipped with the F.A.S.T.-key]
The operation mode is changed to OFF or ACC and the
driver’s door is not opened.NOTE
The light auto-cutout function can be deactivated.
See your authorized Mitsubishi Motors dealer for details.
When you want to keep the lights on:If the combination headlights and dimmer switch is turned to
the “ ” or “ ” position again after the engine is turned off,
the about 3-minute auto-cutout function described above will
not work. The lights (the parking lights, tail lights and license
plate lights) will stay on and will not turn off automatically.
BK0162600US.book 116 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-117
3
Headlight reminder buzzer
N00549800226
[When using a key to start the engine]
If the driver’s door is opened with the key in the “OFF” or
“ACC” position or removed from the ignition switch while the
lights are on, the tone will sound to remind you to turn off the
lights.
[When using the F.A.S.T.-key to start the engine]
If the driver’s door is opened with the operation mode is put in
OFF or ACC, or if the operation mode is changed to OFF while
the lights are on, the tone will sound to remind you to turn off
the lights.
In either case, the lights will turn off automatically and so will
the tone. Or you can turn the light switch to the “OFF” position
to stop the tone.
Dimmer (high/low beam change)
N00549900142
To change the headlights from high beam to low beam and vice
versa, pull the turn signal lever to (1). Switch the headlights to
low beam as a courtesy whenever there are oncoming vehicles,
or when there is traffic moving ahead of you. An illuminated
blue light in the instrument cluster indicates when the head-
lights are on high beam.
BK0162600US.book 117 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-124 Features and controls
3
NOTE
On vehicles with CVT, to ensure a clear rearward view,
the wiper perform several continuous operations when the
reverse gear is engaged and the switch is in the “INT”
position.
Following this continuous operation, the wiper will auto-
matically switch to intermittent operation.

It is possible to modify functions as follows:
• Adjustment of the interval for intermittent operation.
• Changing intermittent wiper operation to continuous
wiper operation.
See your authorized Mitsubishi Motors dealer for
details.

The washer fluid reservoir is located in the engine com-
partment.
Check the fluid level regularly and refill if necessary.
(Refer to “Washer fluid” on page 7-15.)
Precautions to observe when using wipers and
washers
N00523500254
NOTE
Do not use the wipers when the windshield is dry. This
could scratch the glass and wear the wiper blades prema-
turely.

Before using the wipers in cold weather, check to be sure
that the wiper blades are not frozen to the windshield or
rear window. Using the wipers while the blades are frozen
could cause the wiper motor to burn out.

If the wipers are left on the glass out of the parked posi-
tion and they become blocked by ice or other deposits on
the glass, the motor may still burn out even if the wiper
switch is OFF. If deposits form on the windshield, park
your vehicle in a safe place, turn off the engine, and clean
the glass so that the wipers can operate smoothly.

Avoid using the washer for more than 20 seconds at a
time. Do not operate the washer when the washer fluid
reservoir is empty or the pump may fail.

During cold weather, add a recommended washer solution
that will not freeze in the washer fluid reservoir. Other-
wise the washer may not work or may be damaged.
CAUTION
!
If the washer is used in cold weather, washer fluid
sprayed onto the glass might freeze, blocking your
view. Heat the glass with the defroster before using
the washer.
BK0162600US.book 124 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-125
3

Replace the wiper blades when they are worn. Use the
proper size replacement blades. For further information,
please contact your authorized Mitsubishi Motors dealer.
Electric rear window defogger switch
N00523700403
The rear window defogger can be used when the engine is run-
ning.
The indicator light (A) will come on when you press the elec-
tric rear window defogger switch. Electric current will flow
through the heating wires on the rear window to help clear
away moisture or frost.Ty p e 1
BK0162600US.book 125 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-126 Features and controls
3
After about 20 minutes of operation, the system will shut off
automatically.
To switch the defogger OFF before 20 minutes have passed,
press the switch again. The indicator light will go out and the
defogger will turn off.
If you need the defogger for more than 20 minutes, press the
switch again. This will add 20 more minutes.
NOTE
If your vehicle is equipped with heated mirrors, mist can
also be removed from the outside rearview mirrors when
the rear window defogger switch is pressed. (Refer to
“Door mirror heater” on page 3-53.)
CAUTION
!
The rear window defogger is not designed to melt
snow. Remove any snow manually before using the
rear window defogger.
Use the rear window defogger only after the engine
has started and is running. Be sure to turn the
defogger switch off immediately after the window is
clear to save on battery power.Ty p e 2

Do not place stickers, tape, or other items that are
attached with adhesive over the grid wires on the
rear window.
When cleaning the inside rear window, use a soft
cloth and wipe lightly over the grid wires.
CAUTION
!
BK0162600US.book 126 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-133
3
Setting the passcode
Use the following procedure to turn on the security function by
setting a passcode.
1. Press the SPEECH button.
2. Say “Setup.”
3. Say “Passcode.”
4. The voice guide will say “Passcode is disabled. Would
you like to enable it?” Answer “Yes.”
Answer “No” to cancel the setting of the passcode and
return to the main menu.
5. The voice guide will say “Please say a 4-digit passcode.
Remember this passcode. It will be required to use this
system.”
Say a 4-digit number which you want to set as a passcode.
6. For confirmation purposes, the voice guide will say “Pass-
code <4-digit passcode>. Is this correct?” Answer “Yes.”
Answer “No” to return to the passcode input in Step 5.
7. When the registration of the passcode is completed, the
voice guide will say “Passcode is enabled” and the system
will return to the main menu. NOTE
Passcode will be required to access the system after the
next ignition cycle.

It is required for a little time after engine stop that the
entered passcode is actually recorded in the system.
If the ignition switch or the operation mode is made to
ACC or ON or the engine is started immediately after
engine stop, there is a case when the entered passcode is
not recorded in the system. At this time, please try to enter
the passcode again.Entering the passcode
If a passcode has been set and the security function is enabled,
the voice guide will say “Hands-free system is locked. State the
passcode to continue” when the SPEECH button is pressed to
enter voice recognition mode. Say the 4-digit passcode number
to enter the passcode.
If the entered passcode is wrong, the voice guide will say “<4-
digit passcode>, Incorrect passcode. Please try again.” Enter
the correct passcode.
NOTE
You can reenter the passcode as many times as you want.

If you have forgotten your passcode, say “Cancel” to quit
the voice input mode and then check with an authorized
Mitsubishi Motors dealer.
Disabling the passcode
Use the following procedure to turn off the security function by
disabling the passcode. NOTE
System must be unlocked to disable the passcode.
1. Press the SPEECH button.
2. Say “Setup.”
3. Say “Passcode.”
4. The voice guide will say “Passcode is enabled. Would you
like to disable it?” Answer “Yes.”
Answer “No” to cancel the disabling of the passcode and
return to the main menu.
5. When the disabling of the passcode is completed, the
voice guide will say “Passcode is disabled” and the sys-
tem will return to the main menu.
BK0162600US.book 133 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-161
3
Card holderCards can be slipped into the holder (A) on the sun visor.
12 V power outlets
N00525000615
Accessories can be operated while the ignition switch or the
operation mode is in ON or ACC.
To use a “plug-in” type accessory, open the cover, and insert
the plug in the power outlet.
CAUTION
!
Be sure to use a “plug-in” type accessory operating
at 12 V and at 120 W or less.
Also be aware that using electronic equipment with
the engine off may run the battery down.
When the power outlet is not in use, be sure to close
the power outlet cover. This will prevent the power
outlet from becoming clogged and short circuiting.
BK0162600US.book 161 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-162 Features and controls
3Interior lights
N00525300575
NOTE
Be aware that leaving the light illuminated with the engine
off may run the battery down.
Never leave the vehicle without checking that the light is
off.
Dome light
N00525800235
1- ( )
The light illuminates regardless of whether a door or the
liftgate is open or closed.
2- (•)
Delayed off function
The light illuminates when a door or the liftgate is opened.
It goes off approximately 30 seconds after the door or
liftgate is closed.
However, the light goes off immediately with all doors
and the liftgate closed in the following cases:
• When the ignition switch is turned to the “ON” position
or the operation mode is put in ON.
• When the power door lock function is used to lock the
vehicle.
1- Cargo room light → P.3-164
2- Dome light → P. 3 - 1 6 2
BK0162600US.book 162 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-163
3
• When the remote control transmitter of the keyless entry
system or the F.A.S.T.-key is used to lock the vehicle.
• When the door lock/unlock switch or liftgate switch is
pressed to lock the vehicle while carrying the F.A.S.T.-
key.
Auto cut-out function
If the light is left switched on with the ignition switch is in
the “OFF” or “ACC” position or the operation mode is in
OFF or ACC, and a door or the liftgate is opened, it goes
off automatically after approximately 30 minutes.
The light will illuminate again after it automatically goes
off in the following cases:
• When the ignition switch is turned to the “ON” position
or the operation mode is put in ON.
• When the keyless entry system or the F.A.S.T.-key is
operated.
• When all doors and the liftgate are closed.
NOTE
When the key was used to start the engine: if the key is
removed while the doors and liftgate are closed, the light
is illuminated and after approximately 30 seconds it goes
off.

When the F.A.S.T.-key was used to start the engine: if the
operation mode is put in OFF while the doors and liftgate
are closed, the light illuminates and after approximately
30 seconds it goes off.

The time until the light goes off (delayed off) can be
adjusted. See your authorized Mitsubishi Motors dealer
for details.
The auto cut-out function cannot be operated when the
dome light switch is in the “ ” position.
Also, this function can be deactivated. See your autho-
rized Mitsubishi Motors dealer for details.
3- ( )
The light goes off regardless of whether a door or the
liftgate is open or closed.
BK0162600US.book 163 ページ ２０１３年３月２２日　金曜日　午後２時４１分