NISSAN ALMERA N15 1995 Service Manual
Page 1651 of 1701
TROUBLEDIAGNOSES -Supplemental RestraintSystem(SRS)-
Dual AirBag System
Wiring Diagram -SRS -(Cont'd)
RS-SRS-04
AIR BAG
OIAGNOSIS
SENSOR
UNIT
em
<I>:
LHOmodels
<E>: RHOmodels
@:
GAand SReng ine
@:
CDengine
*7 ...
<D
10<E> 6
,
*8 ...
<D
9<E> 3
,
G/B
~
GY/L
~
~
G/W
t
o
•
G/W
~
SSS
SSSSSS
ClK TXRX
~ ~11
2
.°1
G/W
@
GY
IL
G/B
IciJ~
<M~3g)
1$~ -- -1$1
G/W
GY/L
G/B
i
II
G/W
GY/L
G/B
~ ~~JUNCTION BOXNO.2
II B.II 11*711 II*BII(JOINT CONNECTORS)
<flli): <D
JOINT CONNECTOR-5
1*:1 II*.BI~:
<ID
GY/l
G/B
I I
FUSE
Referto
7 .5A BLOCK El-POWER.
rn
(JIB)
~
G
rtl
IGNITION
SWITCH
ON or START
4-J
B
I
To RS-SRS-02 {~B ~
i
<@-B~
•
em
Y
@
Y
Refer
tolast page
(Foldout page).
~Q@
~GY
~(M24):<E>
~ OR
HRS006
RS-31
Page 1652 of 1701
TROUBLEDIAGNOSES -Supplemental RestraintSystem(SRS)-
Dual AirBag System
Self-diagnosis DIAGNOSTIC PROCEDURE 1(@ without CONSULT)
Checking SRSoperation byusing" AIRBAG" warning lamp-
User mode
1. After turning ignition switchfrom"OFF" to"ON", "AIR
BAG" warning lampoperates.
2. Compare "AIRBAG" warning lampoperation tothe chart
below.
"AIR BAG" warning lampoperation -User mode -
IGN ON
i
ON
J
I
OFF ~~----------------
MRS095A
SRS
condition
No malfunction is
detected. No further actionisnec-
essary. Reference
item
ON
OFF
The
system hasproblem GotoDIAGNOSTIC PRO-
and needs tobe repaired CEDURE2,or 3(RS-33
as indicated. or34).
MRS096A
lGN ON
ON •
OFF
Jr--------------------
MRS097A
IGN ON
ON
OFF --------------------
MRS098A
Air
bag isdeployed. GotoCOLLISION DIAG-
NOSIS (RS-40).
Fuse, diagnosis sensor GotoDIAGNOSTIC PRO-
unit orharness ismal- CEDURE 4(RS-38).
functioning andneeds to
be repaired.
Diagnosis sensorunitor GotoDIAGNOSTIC PRO-
"AIR BAG" warning CEDURE5(RS-38).
lamp circuit isshorted or
open andneeds tobe
repaired.
NOTE:
If "AIR BAG" warning lampoperates differently fromtheoper-
ations shown above, referto"AIR BAG" warning lampopera-
tion -Diagnosis mode-,
DIAGNOSTIC PROCEDURE3,RS-34.
Then repair asnecessary.
RS-32
Page 1653 of 1701
TROUBLEDIAGNOSES -Supplemental RestraintSystem(SRS)-
Dual AirBag System
Self-diagnosis (Cont'd)
DIAGNOSTIC PROCEDURE2
(00
withCONSULT)
Inspecting SRSmalfunctioning partsbyusing CONSULT -
Diagnosis mode
1. Turn ignition switch"OFF".
2. Connect "CONSULT" toData linkconnector.
MRS124A
AIRBAG SELF-DIAG RESULTS
NISSAN
CONSULT
START
SUB MODE
I
SRS046
I ~
SELECT SYSTEM
01
I
ENGINE
1
1 '
1-----1
I
I
I 1
MRS125A
I ~
SELECT DIAGMODE
01
I
ECUDISCRIMINATED NO.
I
'======
1 -
1 -
1========
SRS043
• SELF-DIAG RESULTS.
0
FAILURE DETECTED
CONTROL UNIT
I
ERASE
II
PRINT
I
SRS064
3.
Turn ignition switch"ON".
4. Touch "START".
5. Touch "AIRBAG".
6. Touch "SELF-DIAG RESULTS".
7. Diagnostic codesaredisplayed on"SELF-DIAG RESULTS".
RS-33
•
Page 1654 of 1701
•SELF-DIAG RESULTS.
0
FAILURE DETECTED
• NO SELF DIAGNOSTIC
FAILURE INDICATED.
TROUBLE
DIAGNOSES -Supplemental RestraintSystem(SRS)-
Dual AirBag System
Self-diagnosis (Cont'd)
If no self-diagnostic failureisdetected on"SELF-DIAG
RESULTS", nofurther actionisnecessary. Touch"BACK" key
of CONSULT untilSELECT SYSTEM MODEappears, thenturn
off CONSULT.
FURTHER TESTING
MAY BEREQUIRED.
**
ERASE "PRINT
I
SRS044
8.Touch "PRINT".
9. Compare diagnostic codestothe CONSULT DIAGNOSTIC
CODE CHART, pageRS-36.
10. Touch "BACK" keyofCONSULT untilSELECT SYSTEM
MODE appears, thenturnoffCONSULT.
11. Turn ignition switch"OFF", thendisconnect CONSULTand
both battery cables.
12. Repair thesystem asoutlined bythe "Repair order"in
CONSULT DIAGNOSTIC CODECHART, thatcorresponds to
the problem code.Forreplacement procedureofcomponent
parts, refertoRS-12.
13. After repairing thesystem, conduct DIAGNOSTIC PROCE-
DURE 2again.
If repair iscompleted, turnignition switch"OFF", anddis-
connect CONSULT. ThengotoDIAGNOSTIC PROCEDURE 1,
page RS-32.
Door switch DIAGNOSTIC
PROCEDURE 3
(00
without CONSULT)
Inspecting SRSmalfunctioning partsbyusing "AIRBAG" warn-
ing lamp -Diagnosis mode
1. Open driver's door.
2. Turn ignition switchfrom"OFF" to"ON".
3. Press driver's doorswitch atleast 5times within 7seconds
after turning ignition switch"ON".
SRS isnow inDiagnosis mode.
4. "AIR BAG" warning lampoperates indiagnosis modeas
follows:
NOTE:
If
SRS does notenter diagnostic mode,gotoDIAGNOSTIC
PROCEDURE 6,page RS-39.
RS-34
Page 1655 of 1701
TROUBLEDIAGNOSES -Supplemental RestraintSystem(SRS)-
Dual AirBag System
Self-diagnosis (Cont'd)
No.
ON
OFF
IGN
ON
t
"AIR
BAG" warning lampoperation -Diagnosis mode-
@
through
@
are repeated.
MRS100A
SRS
condition
No malfunc-
tion is
detected. No further
action isnec-
essary.
2 ON
OFF
IGN
ON
I
7 sec.
@)
@
(c)
3sec.
2 sec. 2sec. Varies withmalfunctioning part
MRS099A
@
through
@
are repeated.
NOTE: @ -
Interval I
@ -
Start signal (Startsignal
identifies displaymodes)
@ -
Interval II
@ -
Indicates malfunctioning
part (0.5sec. ONand 0.5
sec. OFF iscounted as
one flash.) The
system
has problem
and needs to
be repaired.
5. Malfunctioning partisindicated bythe number offlashes
(part
@).
Compare thenumber offlashes toWARNING
LAMP FLASH CODECHART, pageRS-37, andlocate mal-
functioning part.
6. Turn ignition switch"OFF", anddisconnect bothbattery
cables.
7. Repair thesystem asoutlined bythe "Repair order"in
WARNING LAMPFLASH CODECHART thatcorresponds to
the flash code. Forreplacement procedureofcomponent
parts, refertoRS-12.
8. After repairing thesystem, conduct DIAGNOSTIC PROCE-
DURE 3again.
If repair iscompleted, turnignition switch"OFF"andthen
turn "ON". Pressdriver's doorswitch atleast 5times within
7 seconds afterturning ignition switch"ON".
9. The system isreset fromDiagnostic modetoUser mode.
Next, gotoDIAGNOSTIC PROCEDURE 1,page RS-32. •
RS-35
Page 1656 of 1701
TROUBLEDIAGNOSES -Supplemental RestraintSystem(SRS)-
Dual AirBag System
Self-diagnosis (Cont'd)
CONSULT DIAGNOSTIC CODECHART
Diagnostic item
Explanation Repair
order
Recheck SRSateach replacement.
NO SELF DIAGNOSTIC
•No malfunction isdetected.
-
FAILURE INDICATED.
AIRBAG MODULE
•Driver's airbag module circuitisopen.
1.
Visually checkthewiring harness connec-
[OPEN) (includingthespiral cable)
tions.
AIRBAG MODULE
•Driver's airbag module circuitisshorted 2.
Replace thespiral cable.
3. Replace driver'sairbag module.
[VB-SHORT] tosome power supply circuit. (including
(Beforedisposing ofit,itmust be
the spiral cable)
deployed.)
AIRBAG MODULE
•Driver's airbag module circuitisshorted 4.
Replace thediagnosis sensorunit.
[GND-SHORT] toground. (including thespiral cable) 5.
Replace theairbag harness.
AIRBAG MODULE
•Driver's airbag module circuitsare
[SHORT] shortedtoeach other.
ASSIST A/BMODULE •Front passenger airbag module circuitis
1.
Visually checkthewiring harness connec-
[OPEN] open. tions.
ASSIST A/BMODULE
•Front passenger airbag module circuitis2.
Replace frontpassenger airbag module.
(Before disposing ofit,itmust be
[VB-SHORT] shortedtosome power supply circuit.
deployed.)
ASSIST A/BMODULE •Front passenger airbag module circuitis3.
Replace thediagnosis sensorunit.
[GND-SHORT) shortedtoground. 4.
Replace theairbag harness.
ASSIST A/BMODULE •Front passenger airbag module circuits
[SHORT] areshorted toeach other.
CONTROL UNIT
•Diagnosis sensorunitisout oforder.
1.
Visually
checkthewiring harness connec-
tions.
2. Replace thediagnosis sensorunit.
3. Replace theairbag harness.
4. Replace themain harness.
*
Follow theprocedures innumerical orderwhenrepairing malfunctioning parts.Confirm whether malfunction iseliminated
using theairbag warning lamp(inuser mode) orCONSULT eachtimerepair isfinished.
If
malfunction isstill observed, pro-
ceed tothe next step. When malfunction iseliminated, furtherrepairworkisnot required.
RS-36
Page 1657 of 1701
TROUBLEDIAGNOSES -Supplemental RestraintSystem(SRS)
Dual AirBag System
Self-diagnosis
(Cont'd)
WARNING LAMPFLASH CODECHART
Warning Flashcode
@
Explanation Repair
order
lamp (#offlashes)
RecheckSRSateach replacement.
0
Nomalfunction isdetected.
-
2 The
driver's airbag module circuit
1.Visually checkthewiring harness connections.
is out oforder.
2.Replace thespiral cable.
D.
3.
Replace thedriver's airbag module.
E
(Before
disposing ofit,itmust bedeployed.)
(Ij
-
4.Replace thediagnosis sensorunit.
en
c
5.Replace theairbag harness.
c
ca
7
The
diagnosis sensorunitisout of 1.Visually checkthewiring harness connections.
~
order. 2.
Replace thediagnosis sensorunit.
C)
3.Replace theairbag harness.
«
OJ
.
4.Replace themain harness .
cr:
;:(
8
The
front passenger airbag module 1.Visually checkthewiring harness connections.
circuit isout oforder. 2.Replace thefront passenger airbag module.
(Before disposing of
it,it
must bedeployed.)
3. Replace thediagnosis sensorunit.
4. Replace theairbag harness.
* Follow theprocedures innumerical orderwhen repairing malfunctioning parts.Confirm whether malfunction iseliminaled
using theairbag warning lamp(inuser mode) orCONSULT eachtimerepair isfinished. Ifmalfunction isstill observed, pro-
ceed tothe next step. When malfunction iseliminated, furtherrepairworkisnol required.
RS-37
•
Page 1658 of 1701
TROUBLEDIAGNOSES -Supplemental RestraintSystem(SRS)-
Dual AirBag System
Trouble Diagnoses forAir Bag Warning Lamp
DIAGNOSTIC PROCEDURE 4
SYMPTOM: "AIRBAG" warning lampdoesnotturn off.
{f
UP
SIDE
•
T
AIRBAG
EE3J
Is
air bag module deployed?
No
Is SRS "AirBag" fuse(10A) OK?
Yes Replace
airbag module
and diagnosis sensor
unit. Refer toCOLLISION
DIAGNOSIS, (RS-40).
Replace fuse.
I ~
SELECT SYSTEM
01
I
ENGINE
I
AIRBAG
MRS125A
00
Connect
CONSULT andtouch No
Replace diagnosis sensor
"START".
----....
unit.
• Is "AIRBAG" displayedon
CONSULT?
~Yes
Is harness connection betweenwarning No
Connect warning lamp
lamp anddiagnosis sensorunitOK?
~
anddiagnosis sensorunit
Yes properly.
Ifwarning lamp
still does notgooff,
replace harness.
[RePlace diagnosissensorunit.
DIAGNOSTIC PROCEDURE 5
SYMPTOM: "AIRBAG" warning lampdoesnotturn on.
{f
+
METER
UP
SIDE
EE3J
MRS127A
Is
warning lampfuseOK?
Yes
Is warning lampLEDOK?
Yes
Is harness connection betweenwarning
lamp anddiagnosis sensorunitOK?
Yes
I
Replace diagnosis sensorunit.
RS-38
No
Replace fuse.
Replace warning lamp
LED.
Connect warning lamp
harness properly. Ifwarn-
ing lamp stilldoes not
come on,replace har-
ness.
Page 1659 of 1701
NoSRSisingood order. Set-
ting theCONSULT tothe
Diagnosis modeisimpos-
sible. Nofurther actionis
necessary.
Is
"AIR BAG" warning lampblinking?
Yes
MRS115A
TROUBLE
DIAGNOSES -Supplemental RestraintSystem(SRS)-
Dual AirBag System
Trouble Diagnoses forAir Bag Warning Lamp
m
(Cont'd)
DIAGNOSTIC PROCEDURE 6
SYMPTOM: SRSdoes notenter Diagnostic mode.
m
NoCharge battery.
SRS058
Disconnect
bothbattery cablesand
check battery voltage usingcircuit
te.ster .
• Is battery voltage morethan9V?
Remove driver'sdoorswitch andcheck
continuity betweendriver'sdoorswitch
connector terminals
G)
and
@
under
the following conditions.
No
Replace driver'sdoor
switch.
Condition
Door switch isdepressed
(Door isclosed).
Door switch isreleased
(Door isopen). Continuity
YES
NO
MRS104
00
Check harness continuity betweendriv-
er's door switch connector terminal
@
and body ground .
• Does continuity exist?
Yes
Replace diagnosis sensorunit.
I
Go 10DIAGNOSTIC PROCEDURE3.No
Replace orrepair har-
ness.
•
SRS060
RS-39
Page 1660 of 1701
COLLISIONDIAGNOSIS -Dual AirBag System
To repair theSRS, perform thefollowing steps.
When SRSisactivated inacollision:
CD
Replace thediagnosis sensorunit.
@ Remove
theairbag modules.
@
Check theSRS components usingthetable shown below:
• Replace anySRS components showing
visible
signsofdamage (dents,cracks, deformation).
@
Conduct self-diagnosis. Referto"Self-diagnosis" fordetails (RS-32). Ensuretheremainder ofthe
SRS isoperating properly.
<ID
Install newairbag modules.
@
Conduct self-diagnosis again.
When SRSisnot activated inacollision:
CD
Check theSRS components usingthetable shown below:
• Replace anySRS components showingvisiblesignsofdamage (dents,cracks, deformation).
@
Conduct self-diagnosis usingCONSULT and"'AIR BAG" warning lamp.Referto"Self-diagnosis" for
details (RS-32). EnsureentireSRSoperates properly.
SRS inspection
Part SRSisactivated
SRSisNOT activated
Air bag module REPLACE
1.Remove airbag module. Checkharness coverandconnectors fordamage,
(driver andpassen-
Installwithnew terminalsfordeformities, andharness forbinding.
ger side) bolts.
2-1.Install driverairbag module intothesteering wheeltocheck fitand align-
ment withthewheel.
2-2. Install passenger airbag module intotheinstrument paneltocheck fit
with theinstrument panel.
3. No damage found,reinstall withnewbolts.
4. Ifdamaged-REPLACE. Airbag must bedeployed beforediscarding.
Instrument panel
REPLACE 1.Check instrument panelforbending, deformities, orcracks.
Install withnew
2.Ifno damage isfound, reinstall withnewbolts.
bolts. 3.Ifdamaged-REPLACE.
Diagnosis sensor REPLACE
1.Check caseandbracket fordents, cracks ordeformities.
unit Installwithnew
2.Check connectors fordamage, andterminals fordeformities.
bolts. 3.Ifno damage isfound, reinstall withnewbolts.
4. Ifdamaged-REPLACE.
Steering wheel
1.Visually checksteering wheelfordeformities.
2. Check harness (builtintosteering wheel)andconnectors fordamage, andterminals fordeformi-
ties.
3. Install airbag module tocheck fitor alignment withsteering wheel.
4. Check steering wheelforexcessive freeplay.
5. Ifno damage isfound, reinstall withnewbolts.
6. Ifdamaged-REPLACE.
Spiral cable
1.Visually checklock(engagement) pinsandcombination switchfordamage.
2. Check connectors, flatcable andprotective tapefordamage.
3. Check steering wheelfornoise, binding orheavy operation.
4. Ifno damage isfound, reinstall withnew bolts.
5. Ifdamaged-REPLACE.
Harness andCon-
1.Check connectors forpoor connection, damage,andterminals fordeformities.
nectors 2.Check harness forbinding, chafing,cuts,ordeformities.
3. Ifno damage isfound, reinstall theharness andconnectors.
4. Damaged-REPLACE damagedsectionofharness. Donot attempt torepair, spliceormodify any
SRS harness.
RS-40