Peugeot 107 Dag 2006 Owner's Guide

23Audio equipment-
01-01-2006
GENERAL FUNCTIONSOn / off
With the ignition key
in the accessories
position or with the
ignition on, press this button to switch
the audio equipment on or off.
After the engine has been switched
off, the audio equipment can
only operate for approximately
30 minutes, to prevent discharging
of the battery. Press the upper part
of this button several
times in succession to
increase the volume of
the audio equipment
or the lower part of this
button to decrease it.
VOLUME ADJUSTMENT
CLOCK ADJUSTMENT
Press this button
several times in
succession to gain
access to the bass
(BASS) , treble (TREB), front / rear
balance (FAD) and left / right balance
(BAL) settings.
AUDIO SETTINGS
Press this button for
more than 2 seconds,
the clock display
flashes:
AUXILIARY SOCKET
An auxiliary socket
"AUX" is provided
for the connection of
portable equipment
(MP3 player, etc.).
When the parameter
is displayed, change
the setting using these
two buttons.
You exit from this mode automatically
after a few seconds without any
action. In order to listen
to it, connect your
equipment then press
this button.
The audio equipment controls enable
you to adjust the volume and the
audio settings.
To exit from the AUX source, press
AM/FM .
- to adjust the hours, press this button,
- to adjust the minutes, press this button. Note:
set the volume of the
portable equipment to half
volume to avoid saturating
the audio equipment sound.
Then use the audio equipment
volume button.
You exit from this mode automatically
after a few seconds without any
action.

Audio equipment24 -
01-01-2006
Selection of the AM / FM
(FM1, FM2, FM3) wavebands Autostore: automatic storing of
6 stations on AM and FM3 TA function on/off: traffic
information priority
Automatic search for a higher frequency: double press / Successive tuning in to the stations Selection of the type of radio
programme: News, Sports, Talk, Pop, Classics AF function on/off:
alternative frequency
Manual search for
a higher frequency
Selection of the stored station / Storing of a station: press for more than 2 seconds Manual search for
a lower frequency
RADIO

25Audio equipment-
01-01-2006
Stereo reception
When the audio equipment receives
a station broadcasting in stereo it
automatically transmits stereo sound
and the screen displays "ST". If the
reception conditions deteriorate, the
audio equipment returns to mono
transmission and "ST" is no longer
displayed. Press one of these
two buttons briefly to
increase or decrease
the frequency dis-
played respectively.
If you maintain the
pressure on the
button in the chosen
direction, the frequency will be
scanned continuously.
The scan stops when you release the
button.
Manual station search
Automatic station search
Manual station storing
Selection of the radio source
Selection of a waveband
Press this button. Press this button
twice to select the
next station.
Press this button
briefly to listen to each station
available on the FM waveband for
three seconds. To stop the station
scan, press this button again.
If the traffic information programme
TA is selected, only stations which
broadcast this type of programme
are selected.
Press the button
several times in
succession to select
the wavebands FM1,
FM2, FM3 and AM. Select the required station.
Press one of the buttons "1" to "6"
for more than 2 seconds
An audible signal confirms that the
station has been stored.

Audio equipment26 -
01-01-2006
Notes on radio
reception
Your audio equipment will
be subjected to phenomena
which do not affect domestic radio
sets. Both MW/LW and FM reception
are subject to various forms of
interference. This is no reflection on
the quality of the equipment but is due
to the nature of the signals and the
way in which they are transmitted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the
result of increasing distance from the
transmitter, deflection of the signal by
obstacles (mountains, hills, buildings,
etc) or of being in an area which is
not covered by a transmitter.
Automatic storing of FM
stations (autostore)
Press this button.
Your audio equipment
automatically stores
the six best transmit-
ters received on AM and FM in your
current location. These stations are
stored on the AM and FM3 wave-
bands. The end of the search is si-
gnalled by two audible signals.
Recalling stored stations
On each waveband, a brief press on
one of the buttons "1" to "6" recalls
the corresponding stored station.
If it was not possible to find six
transmitters, the remaining
memories remain empty:
three dashes are displayed
on the audio equipment screen for
each empty memory.

27Audio equipment-
01-01-2006
RDS
Using the AF (alternative
frequency) function on the FM
waveband
Regional following
mode (REG)
This enables you to listen to stations
which broadcast a type of programme
which has a theme (NEWS, SPORTS,
TALK, POP, CLASSICS).
Search by type of
programme (PTY)EON system
This system links stations which
belong to the same network. It permits
the transmission of traffic information
broadcast by a station which belongs
to the same network as the station to
which you are listening.
In order to benefit from this, select the
traffic information programme
TA.
The
RDS (Radio Data System)
enables you to continue listening to
the same station irrespective of the
frequency that it uses in your current
location. The audio equipment
continuously searches for the
transmitter which provides the best
reception.
Some stations, organised in a network,
broadcast regional programmes in
the various regions which they serve.
The regional following mode enables
you to contiue listening to the same
programme. Press this button seve-
ral times in succession
to activate or deacti-
vate the function.
On FM, the multifunction display will
indicate:
- "TP" or "TP EON" : the radio
transmits a programme while
awaiting the broadcasting of traffic
information.
- "TA" or "TA EON" : the programme
transmitted by the radio is put
on standby while awaiting the
broadcasting of traffic information.
If you wish to interrupt the
transmission of a message, press
this button again.
Traffic information
programme (TA)
Press this button se-
veral times in suc-
cession to activate or
deactivate the func-
tion.
The screen will indicate:
- "AF" if the function is activated,
- "AF REG" if the function is activated
at regional level,
- "AF" flashing if the function is not
available. When
FM is selected,
press this button:
- "no pty" is displayed,
- then press the button briefly to select a programme.
After a few seconds without any
action, your selection is stored. Notes:
the volume of
the traffic information is
independent of the volume
of normal radio listening.
You can adjust it using the volume
button, when the TA programme is
being transmitted.
The setting will be stored and will be
used during subsequent message
transmissions.

Audio equipment28 -
01-01-2006
CD ejectSelection of the source:
CD or CD changer or auxiliary Selection of the next track
Playing of the start of each
track on the CD: brief press 
: accelerated forwards play
 : accelerated backwards play Selection of the previous track
Random playing of the tracks on the CD currently being played
CD changer:
 : selection of the previous CD
 : selection of the next CD CD: repeating of the current track /
CD changer, press for more than 2 seconds: repeating of the current CD
CD PLAYER OR CD CHANGER

29Audio equipment-
01-01-2006
Press this button to
select the next track.
Press this button to
return to the start of
the current track or
to select the previous
track.
CD PLAYER AND CD
CHANGER FUNCTIONS
Selection of a track on a CD
Introscan (SCAN)
Press this button to
listen to the start of
each track on the
current CD.
Accelerated play
Press and hold one
of these buttons for
accelerated forwards
or backwards play
respectively.
The accelerated play
stops when the button
is released.When a CD is inser-
ted, printed face up-
permost, play begins
automatically.
If there is a CD in the player already,
press this button.
CD PLAYER FUNCTIONS
Selection of the CD player Repeating of a track on the
CD (RPT)
Random playing of the CD
(RAND)
When the CD player
is selected, press this
button. If you wish to listen
to the current track
again, press this
button. To cancel the
repetition, press the button again.
CD eject
Press this button to
eject the CD from the
player.
The tracks on the CD will be played
in a random order. Press the button
again to return to normal play.
The random play mode is deactivated
when the audio equipment is switched
off. The use of copied CDs may
cause faults.
Insert circular CDs only.

Audio equipment28 -
01-01-2006
CD ejectSelection of the source:
CD or CD changer or auxiliary Selection of the next track
Playing of the start of each
track on the CD: brief press 
: accelerated forwards play
 : accelerated backwards play Selection of the previous track
Random playing of the tracks on the CD currently being played
CD changer:
 : selection of the previous CD
 : selection of the next CD CD: repeating of the current track /
CD changer, press for more than 2 seconds: repeating of the current CD
CD PLAYER OR CD CHANGER

29Audio equipment-
01-01-2006
Press this button to
select the next track.
Press this button to
return to the start of
the current track or
to select the previous
track.
CD PLAYER AND CD
CHANGER FUNCTIONS
Selection of a track on a CD
Introscan (SCAN)
Press this button to
listen to the start of
each track on the
current CD.
Accelerated play
Press and hold one
of these buttons for
accelerated forwards
or backwards play
respectively.
The accelerated play
stops when the button
is released.When a CD is inser-
ted, printed face up-
permost, play begins
automatically.
If there is a CD in the player already,
press this button.
CD PLAYER FUNCTIONS
Selection of the CD player Repeating of a track on the
CD (RPT)
Random playing of the CD
(RAND)
When the CD player
is selected, press this
button. If you wish to listen
to the current track
again, press this
button. To cancel the
repetition, press the button again.
CD eject
Press this button to
eject the CD from the
player.
The tracks on the CD will be played
in a random order. Press the button
again to return to normal play.
The random play mode is deactivated
when the audio equipment is switched
off. The use of copied CDs may
cause faults.
Insert circular CDs only.

Audio equipment30 -
01-01-2006
Press this button.
CD CHANGER FUNCTIONS
Selection of the CD changerRandom playing of a CD
(RAND)
When the CD changer
is selected, press this
button for 2 seconds.
The tracks of the
current CD will be played in a random
order.
Press the button again for 2 seconds
to return to normal play.
Selection of a CD
Press one of these
buttons on the audio
equipment to select
the previous or next
CD respectively.
Repeating of a CD (RPT)
If you wish to listen to
the current CD again,
press and hold this
button.
The use of copied CDs may
cause faults.
Insert circular CDs only.
To cancel the repetition, press the
button again.