Peugeot 206 SW Dag 2004 Owner's Guide

22
14-06-2004
23
14-06-2004
Dynamic stability
control system (ESP/
ASR) warning light
This comes on for a few seconds
each time the ignition is switched
on.
With the engine running and when
the vehicle is moving, it comes on if
the system is activated.
It lights permanently when the sys-
tem is disarmed.
If the warning light remains lit with
the engine running and when the ve-
hicle is moving, consult a PEUGEOT
dealer.
Battery charge warning
light
This indicates one of the fol-
lowing:
- faulty operation of the charging circuit,
- slack battery or starter terminals,
- a cut or slack alternator belt,
- an alternator failure.
Consult a PEUGEOT dealer.
Engine diagnostics
warning light
(according to model)
This comes on for a few seconds
each time the ignition is switched
on.
If it comes on with the engine run-
ning, this indicates incorrect opera-
tion of the injection, ignition or emis-
sion control system.
If the warning light lashes, there is a
risk of damage to the catalytic con-
verter on petrol engines.
Consult a PEUGEOT dealer.
Diesel engine pre-heat
warning light
Wait until the warning light
goes out before starting the engine.
If the temperature is high enough,
the warning light comes on for less
than one second. You can start the
engine without waiting.
PEF saturation warning
(Diesel)
An audible signal and a message
on the multi-function display indicate
clogging of the diesel ilter (PEF), this
is the beginning of saturation of the
particle emission ilter due to excep-
tionally prolonged urban driving con-
ditions: low speed, long trafic jams,
In order to regenerate the ilter, you
are advised to drive at a speed of
40 mph (60 km/h) or above as soon
as possible when trafic conditions
permit for at least ive minutes, until
the message disappears. If this fault
persists, consult a PEUGEOT dealer
as soon as possible.
INSTRUMENTS AND CONTROLS
Low fuel level
warning light
When this light irst
comes on, you have enough fuel
to drive at least 30 miles (50 km).
The tank capacity is approximately
50 litres.
Water in diesel filter
indicator*
If this warning light comes on,
accompanied by an audible signal and
a message on the multi-function dis-
play, this indicates that there is a risk of
damage to the injection system.
Consult a PEUGEOT dealer as soon
as possible.
Diesel additive level warning
(Diesel)
An audible signal and a message on
the multi-function display indicate a low
diesel additive level. This additive must
be topped up, consult a PEUGEOT
dealer as soon as possible.

22
14-06-2004
23
14-06-2004
Seat belt not fastened
warning light*
When the ignition is switched
on, this indicator light comes on if the
driver has not fastened his seat belt.
Above 12 mph (20 km/h), the warn-
ing light lashes for about two min-
utes accompanied by an increasingly
audible signal and a message on the
multifunction display. This warning
light remains lit until the driver's seat
belt is fastened.
Passenger air bag
disarmed warning
light*
Illumination of this warning light ac-
companied by a message on the
multi-function display, indicates that
the passenger air bag is disarmed.
The warning light remains lit as long as
the passenger air bag is disarmed.
Always consult a PEUGEOT dealer if
the warning light lashes.
Air bags warning light
The light will come on for a
few seconds when the igni-
tion is switched on.
With the engine running, illumination
of this warning light, accompanied by
an audible signal and a message on
the multi-function display, indicates a
fault in the air bags.
Consult a PEUGEOT dealer.
Coolant temperature indicator
- needle in zone (A), the tempera-
ture is correct,
- needle in zone (B), the tempera-
ture is too high. The central STOP
warning light lashes.
You must stop.
Consult a PEUGEOT dealer.
INSTRUMENTS AND CONTROLS
Engine oil temperature
indicator
With the engine running, this indi-
cates the oil temperature:
- needle in zone (C), the tempera-
ture is correct,
- needle in zone (D), the tempera-
ture is too high. To lower the oil
temperature, reduce your speed.
* According to country.

22
14-06-2004
23
14-06-2004
Seat belt not fastened
warning light*
When the ignition is switched
on, this indicator light comes on if the
driver has not fastened his seat belt.
Above 12 mph (20 km/h), the warn-
ing light lashes for about two min-
utes accompanied by an increasingly
audible signal and a message on the
multifunction display. This warning
light remains lit until the driver's seat
belt is fastened.
Passenger air bag
disarmed warning
light*
Illumination of this warning light ac-
companied by a message on the
multi-function display, indicates that
the passenger air bag is disarmed.
The warning light remains lit as long as
the passenger air bag is disarmed.
Always consult a PEUGEOT dealer if
the warning light lashes.
Air bags warning light
The light will come on for a
few seconds when the igni-
tion is switched on.
With the engine running, illumination
of this warning light, accompanied by
an audible signal and a message on
the multi-function display, indicates a
fault in the air bags.
Consult a PEUGEOT dealer.
Coolant temperature indicator
- needle in zone (A), the tempera-
ture is correct,
- needle in zone (B), the tempera-
ture is too high. The central STOP
warning light lashes.
You must stop.
Consult a PEUGEOT dealer.
INSTRUMENTS AND CONTROLS
Engine oil temperature
indicator
With the engine running, this indi-
cates the oil temperature:
- needle in zone (C), the tempera-
ture is correct,
- needle in zone (D), the tempera-
ture is too high. To lower the oil
temperature, reduce your speed.
* According to country.

24
14-06-2004
25
14-06-2004
INSTRUMENTS AND CONTROLS
Display screen showing the
positions of the automatic
gearbox selector lever Automatic gearbox indicator
lights
Park
Reverse
Neutral
Drive
Manual mode: 1st gear engaged
2nd gear engaged
3rd gear engaged
4th gear engaged "SPORT" Indicator light
This comes on when the
"SPORT"
program is selected.
"SNOW" Indicator light
This comes on when the
"SNOW" program is selected.
Operating abnormality
If the Sport and Snow indicator lights
lash, accompanied by an audible
signal and a message on the multi-
function diplay, consult a PEUGEOT
dealer.

24
14-06-2004
25
14-06-2004
INSTRUMENTS AND CONTROLS
Service indicator
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the man-
ufacturer's servicing schedule.
Operation
As soon as the ignition is switched
on and for 5 seconds, the spanner
symbolising ''service operation'' is lit.
The trip recorder display shows the
distance remaining (in round igures)
before the next service.
Example: 4,800 miles/km remain
before the next service is due. When
the ignition comes on and for 5 sec-
onds the display indicates: 5 seconds after the ignition is
switched on, the total distance re-
corder resumes normal operation
and the display shows the total or trip
distances.
The distance remaining before the
next service is less than 500 miles
(1,000 km).
Example:
400 miles (900 km) remain
before the next service is due.
When switching on the ignition and
for 5 seconds, the display shows:
5 seconds after the ignition is
switched on, the total distance re-
corder resumes normal operation
and the symbol remains lit.
This indicates that a service should
be carried out shortly. The display
shows the total or trip distances. The service is overdue.
Each time the ignition is switched on
and for 5 seconds, the symbol and
the excess distance lash.
Example:
the service is overdue by
300 miles/km. The service should be
carried out very shortly.
When the ignition is switched on and
for 5 seconds, the display shows:
INSTRUMENT PANEL
DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder, it remains displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
5 seconds after the ignition is
switched on, the total distance record-
er resumes normal operation and the
symbol remains lit. The display shows
the total or trip distances.
Note: the service spanner lights if the
two-year interval has been exceeded*.
* According to country.

26
14-06-2004
27
14-06-2004
INSTRUMENTS AND CONTROLS
Resetting the service indicator
Your PEUGEOT dealer carries out
this operation after each service. The
reset procedure is as follows:
- Switch off the ignition.
- Press and hold button 1.
- Switch on the ignition.
The display begins a 10 second
countdown.
- Keep button 1 pressed for 10 sec-
onds.
The display shows [= 0] and the
service symbol disappears.Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 10 seconds, after the
service information. Oil level gauge fault
Flashing of the six segments indi-
cates a malfunction of the oil level
gauge.
There is a risk of damage to the engine.
Contact a PEUGEOT dealer.
Surplus of oil
Flashing of the six squares and dis-
playing of "max" indicate a surplus of
oil which could damage the engine.
If the surplus of oil is conirmed by
a check using the dipstick, contact a
PEUGEOT dealer without delay.
Lack of oil
Flashing of the six segments and dis-
playing of "min" indicate a lack of oil
which could damage the engine.
If the lack of oil is conirmed by a
check using the dipstick, it is essen-
tial that the level is topped up. The level read on the gauge will
only be correct if the vehicle
is on level ground and the en-
gine has been off for more than
10 minutes.

26
14-06-2004
27
14-06-2004
INSTRUMENTS AND CONTROLS
Total distance recorder
Briely pressing button 1 alternates
between the total and trip distance
displays.
To reset the trip recorder to zero,
when it is displayed press button 1
until zeros appear.
LIGHTING RHEOSTAT
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
HAZARD WARNING
LIGHTS
Press the button, the direction indica-
tors lash.
They can operate with the ignition off.
Automatic lighting of hazard
warning lights*
When braking in an emergency, de-
pending on the force of deceleration,
the hazard warning lights come on au-
tomatically. They switch off automati-
cally the irst time you accelerate.
It is also possible to switch them off
by pressing the button.
* According to destination.

28
14-06-2004
29
14-06-2004
YOUR 206 IN DETAIL
CLOCK
Adjusting the parameters
Press and hold button 1 for two sec-
onds to access the settings; the data
lashes, indicating it is ready to be
modiied.
Then, each press of button 1 scrolls
through the various data in the fol-
lowing order:
- language of information displayed,
- hours (12 then 24 hour mode),
- minutes,
- year,
- month,
- day,
- unit of temperature (degrees Celsius or Fahrenheit).
Pressing button 2 allows modiication
of the data selected. Press and hold
for rapid advance (return to start after
the last possible value).
After 7 seconds with no action, the main
display returns; the modiied data are
now recorded.
Note: Pressing button 2 briely dis-
plays the outside temperature for a
few seconds.
Button
1: hour adjustment
Button 2: minute adjustment
Press and hold the button for rapid
advance.DISPLAY A
This displays the following informa-
tion:
- the time,
- the date,
- the outside temperature* (this lashes if there is a risk
of ice),
- the audio system displays,
- a door check (e.g.: ''left front door open''),
- warning messages (e.g. ''remote control battery lat'')
or information
฀-฀฀ messages
(e.g. ''economy mode active''),
displayed temporarily.
* According to model.

28
14-06-2004
29
14-06-2004
YOUR 206 IN DETAIL
Setting the parameters
Press button 1 for two seconds to
access the settings. The information
lashes to show it is ready to be mo-
diied.
Then, individual presses on button
1 allow you to scroll through the va-
rious data in the following sequence:
- language in which the information is displayed,
- unit of distance (kms or miles),
- unit of temperature (degrees Celsius or Fahrenheit),
- time format (12 then 24 hour mode),
- hour,
- minutes,
- year,
- month,
- day.
Pressing button 2 allows you to chan-
ge the information selected. Maintain
the pressure for rapid scrolling.
After 7 seconds without operation,
the screen returns to the main display
and the modiied data is recorded.DISPLAY B
This enables the following informa-
tion to be displayed:
- the time,
- the date,
- the outside temperature (this lashes when there is a risk of ice),
- the radio displays,
- the status of the doors. The display shows you, by means of a graphic,
whether a door is open,
- the warning messages (e.g. ''battery charge low'') or information messa-
ges (e.g. "fuel tank low''), displayed
temporarily, can be cleared by pres-
sing button 1 or 2,
- the trip computer.

30
14-06-2004
31
14-06-2004
YOUR 206 IN DETAIL
MONOCHROME SCREEN CT
This is controlled by the RT3 GPS
audio/telephone keypad.
It enables the following information to
be displayed:
- the time,
- the date,
- the outside temperature (a mes- sage warns you when there is a
risk of ice),
-
the audio source displays (radio, CD, ...),- the telematic system displays (tele- phone, services, ...),
- the status of the openings (doors, bonnet, ...),
- the warning messages (e.g. "Fuel le- vel low") and vehicle functions status
messages (e.g. "Passenger air bag
deactivated") displayed temporarily,
- the trip computer display (see cor- responding section),
- the satellite navigation system dis- plays (see corresponding section). Coniguration menu
This gives access to the following
parameters:
- "Adjust the brightness": adjust the
brightness of the display.
- "Sound": voice synthesiser setting (for the masculine/feminine voice
parameter; insert the coniguration
CD-Rom); setting of the spoken
commands.
- "International parameters": date and time setting (12 or 24 hour
mode, adjustment of the minutes
on GPS); units setting (l/100 - °C or
mpg - °F).
- "Choice of the language": choice of the language of the display, in-
formation and spoken commands
(German, English, Spanish, French,
Italian, Dutch, Portuguese: insert
the coniguration CD-Rom).
Main menu
Press the RT3 audio/telephone
"MENU"
button to access the main
menu and select one of the following
applications:
- navigation - guidance (see section "Satellite navigation system"),
- audio functions (see "RT3 Audio/ telephone" section),
- trip computer (see corresponding section),
- directory (see "RT3 audio/telephone" section),
- telematics (see "RT3 audio/telephone" section),
- coniguration.
Note: to enable you to use all of your
system's functions, you have two CD
ROMs: one, "Coniguration", contains
the software and the various display
and spoken information languages,
the other, "Navigation", contains the
satellite navigation system map data.